xhci: replace xhci_readl() with readl()
Function xhci_readl() is used to read 32bit xHC registers residing in MMIO
address space. It takes as first argument a pointer to the xhci_hcd although
it does not use it. xhci_readl() internally simply calls readl(). This creates
an illusion that xhci_readl() is an xhci specific function that has to be
called in a context where a pointer to xhci_hcd is available.
Remove the unnecessary xhci_readl() wrapper function and replace its calls to
with calls to readl() to make the code more straightforward.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 99e7251..3682a3b 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -1986,7 +1986,7 @@
}
/* Port offset and count in the third dword, see section 7.2 */
- temp = xhci_readl(xhci, addr + 2);
+ temp = readl(addr + 2);
port_offset = XHCI_EXT_PORT_OFF(temp);
port_count = XHCI_EXT_PORT_COUNT(temp);
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
@@ -2069,7 +2069,7 @@
int cap_count = 0;
addr = &xhci->cap_regs->hcc_params;
- offset = XHCI_HCC_EXT_CAPS(xhci_readl(xhci, addr));
+ offset = XHCI_HCC_EXT_CAPS(readl(addr));
if (offset == 0) {
xhci_err(xhci, "No Extended Capability registers, "
"unable to set up roothub.\n");
@@ -2106,7 +2106,7 @@
/* count extended protocol capability entries for later caching */
do {
u32 cap_id;
- cap_id = xhci_readl(xhci, tmp_addr);
+ cap_id = readl(tmp_addr);
if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL)
cap_count++;
tmp_offset = XHCI_EXT_CAPS_NEXT(cap_id);
@@ -2120,7 +2120,7 @@
while (1) {
u32 cap_id;
- cap_id = xhci_readl(xhci, addr);
+ cap_id = readl(addr);
if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL)
xhci_add_in_port(xhci, num_ports, addr,
(u8) XHCI_EXT_PORT_MAJOR(cap_id),
@@ -2224,7 +2224,7 @@
INIT_LIST_HEAD(&xhci->cancel_cmd_list);
- page_size = xhci_readl(xhci, &xhci->op_regs->page_size);
+ page_size = readl(&xhci->op_regs->page_size);
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
"Supported page size register = 0x%x", page_size);
for (i = 0; i < 16; i++) {
@@ -2247,10 +2247,10 @@
* Program the Number of Device Slots Enabled field in the CONFIG
* register with the max value of slots the HC can handle.
*/
- val = HCS_MAX_SLOTS(xhci_readl(xhci, &xhci->cap_regs->hcs_params1));
+ val = HCS_MAX_SLOTS(readl(&xhci->cap_regs->hcs_params1));
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
"// xHC can handle at most %d device slots.", val);
- val2 = xhci_readl(xhci, &xhci->op_regs->config_reg);
+ val2 = readl(&xhci->op_regs->config_reg);
val |= (val2 & ~HCS_SLOTS_MASK);
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
"// Setting Max device slots reg = 0x%x.", val);
@@ -2331,7 +2331,7 @@
*/
xhci->cmd_ring_reserved_trbs++;
- val = xhci_readl(xhci, &xhci->cap_regs->db_off);
+ val = readl(&xhci->cap_regs->db_off);
val &= DBOFF_MASK;
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
"// Doorbell array is located at offset 0x%x"
@@ -2382,7 +2382,7 @@
}
/* set ERST count with the number of entries in the segment table */
- val = xhci_readl(xhci, &xhci->ir_set->erst_size);
+ val = readl(&xhci->ir_set->erst_size);
val &= ERST_SIZE_MASK;
val |= ERST_NUM_SEGS;
xhci_dbg_trace(xhci, trace_xhci_dbg_init,
@@ -2431,7 +2431,7 @@
* is necessary for allowing USB 3.0 devices to do remote wakeup from
* U3 (device suspend).
*/
- temp = xhci_readl(xhci, &xhci->op_regs->dev_notification);
+ temp = readl(&xhci->op_regs->dev_notification);
temp &= ~DEV_NOTE_MASK;
temp |= DEV_NOTE_FWAKE;
xhci_writel(xhci, temp, &xhci->op_regs->dev_notification);