| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| */ |
| |
| #define pr_fmt(fmt) "[drm-dp]: %s: " fmt, __func__ |
| |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_atomic.h> |
| #include <drm/drm_crtc.h> |
| |
| #include "msm_drv.h" |
| #include "msm_kms.h" |
| #include "sde_connector.h" |
| #include "dp_drm.h" |
| #include "dp_debug.h" |
| |
| #define DP_MST_DEBUG(fmt, ...) pr_debug(fmt, ##__VA_ARGS__) |
| |
| #define to_dp_bridge(x) container_of((x), struct dp_bridge, base) |
| |
| void convert_to_drm_mode(const struct dp_display_mode *dp_mode, |
| struct drm_display_mode *drm_mode) |
| { |
| u32 flags = 0; |
| |
| memset(drm_mode, 0, sizeof(*drm_mode)); |
| |
| drm_mode->hdisplay = dp_mode->timing.h_active; |
| drm_mode->hsync_start = drm_mode->hdisplay + |
| dp_mode->timing.h_front_porch; |
| drm_mode->hsync_end = drm_mode->hsync_start + |
| dp_mode->timing.h_sync_width; |
| drm_mode->htotal = drm_mode->hsync_end + dp_mode->timing.h_back_porch; |
| drm_mode->hskew = dp_mode->timing.h_skew; |
| |
| drm_mode->vdisplay = dp_mode->timing.v_active; |
| drm_mode->vsync_start = drm_mode->vdisplay + |
| dp_mode->timing.v_front_porch; |
| drm_mode->vsync_end = drm_mode->vsync_start + |
| dp_mode->timing.v_sync_width; |
| drm_mode->vtotal = drm_mode->vsync_end + dp_mode->timing.v_back_porch; |
| |
| drm_mode->vrefresh = dp_mode->timing.refresh_rate; |
| drm_mode->clock = dp_mode->timing.pixel_clk_khz; |
| |
| if (dp_mode->timing.h_active_low) |
| flags |= DRM_MODE_FLAG_NHSYNC; |
| else |
| flags |= DRM_MODE_FLAG_PHSYNC; |
| |
| if (dp_mode->timing.v_active_low) |
| flags |= DRM_MODE_FLAG_NVSYNC; |
| else |
| flags |= DRM_MODE_FLAG_PVSYNC; |
| |
| drm_mode->flags = flags; |
| |
| drm_mode->type = 0x48; |
| drm_mode_set_name(drm_mode); |
| } |
| |
| static int dp_bridge_attach(struct drm_bridge *dp_bridge) |
| { |
| struct dp_bridge *bridge = to_dp_bridge(dp_bridge); |
| |
| if (!dp_bridge) { |
| pr_err("Invalid params\n"); |
| return -EINVAL; |
| } |
| |
| pr_debug("[%d] attached\n", bridge->id); |
| |
| return 0; |
| } |
| |
| static void dp_bridge_pre_enable(struct drm_bridge *drm_bridge) |
| { |
| int rc = 0; |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge) { |
| pr_err("Invalid params\n"); |
| return; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| dp = bridge->display; |
| |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| return; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| return; |
| } |
| |
| /* By this point mode should have been validated through mode_fixup */ |
| rc = dp->set_mode(dp, bridge->dp_panel, &bridge->dp_mode); |
| if (rc) { |
| pr_err("[%d] failed to perform a mode set, rc=%d\n", |
| bridge->id, rc); |
| return; |
| } |
| |
| rc = dp->prepare(dp, bridge->dp_panel); |
| if (rc) { |
| pr_err("[%d] DP display prepare failed, rc=%d\n", |
| bridge->id, rc); |
| return; |
| } |
| |
| /* for SST force stream id, start slot and total slots to 0 */ |
| dp->set_stream_info(dp, bridge->dp_panel, 0, 0, 0, 0, 0); |
| |
| rc = dp->enable(dp, bridge->dp_panel); |
| if (rc) { |
| pr_err("[%d] DP display enable failed, rc=%d\n", |
| bridge->id, rc); |
| dp->unprepare(dp, bridge->dp_panel); |
| } |
| } |
| |
| static void dp_bridge_enable(struct drm_bridge *drm_bridge) |
| { |
| int rc = 0; |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge) { |
| pr_err("Invalid params\n"); |
| return; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| return; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| return; |
| } |
| |
| dp = bridge->display; |
| |
| rc = dp->post_enable(dp, bridge->dp_panel); |
| if (rc) |
| pr_err("[%d] DP display post enable failed, rc=%d\n", |
| bridge->id, rc); |
| } |
| |
| static void dp_bridge_disable(struct drm_bridge *drm_bridge) |
| { |
| int rc = 0; |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge) { |
| pr_err("Invalid params\n"); |
| return; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| return; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| return; |
| } |
| |
| dp = bridge->display; |
| |
| if (!dp) { |
| pr_err("dp is null\n"); |
| return; |
| } |
| |
| if (dp) |
| sde_connector_helper_bridge_disable(bridge->connector); |
| |
| rc = dp->pre_disable(dp, bridge->dp_panel); |
| if (rc) { |
| pr_err("[%d] DP display pre disable failed, rc=%d\n", |
| bridge->id, rc); |
| } |
| } |
| |
| static void dp_bridge_post_disable(struct drm_bridge *drm_bridge) |
| { |
| int rc = 0; |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge) { |
| pr_err("Invalid params\n"); |
| return; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| return; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| return; |
| } |
| |
| dp = bridge->display; |
| |
| rc = dp->disable(dp, bridge->dp_panel); |
| if (rc) { |
| pr_err("[%d] DP display disable failed, rc=%d\n", |
| bridge->id, rc); |
| return; |
| } |
| |
| rc = dp->unprepare(dp, bridge->dp_panel); |
| if (rc) { |
| pr_err("[%d] DP display unprepare failed, rc=%d\n", |
| bridge->id, rc); |
| return; |
| } |
| } |
| |
| static void dp_bridge_mode_set(struct drm_bridge *drm_bridge, |
| struct drm_display_mode *mode, |
| struct drm_display_mode *adjusted_mode) |
| { |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge || !mode || !adjusted_mode) { |
| pr_err("Invalid params\n"); |
| return; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| return; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| return; |
| } |
| |
| dp = bridge->display; |
| |
| dp->convert_to_dp_mode(dp, bridge->dp_panel, adjusted_mode, |
| &bridge->dp_mode); |
| } |
| |
| static bool dp_bridge_mode_fixup(struct drm_bridge *drm_bridge, |
| const struct drm_display_mode *mode, |
| struct drm_display_mode *adjusted_mode) |
| { |
| bool ret = true; |
| struct dp_display_mode dp_mode; |
| struct dp_bridge *bridge; |
| struct dp_display *dp; |
| |
| if (!drm_bridge || !mode || !adjusted_mode) { |
| pr_err("Invalid params\n"); |
| ret = false; |
| goto end; |
| } |
| |
| bridge = to_dp_bridge(drm_bridge); |
| if (!bridge->connector) { |
| pr_err("Invalid connector\n"); |
| ret = false; |
| goto end; |
| } |
| |
| if (!bridge->dp_panel) { |
| pr_err("Invalid dp_panel\n"); |
| ret = false; |
| goto end; |
| } |
| |
| dp = bridge->display; |
| |
| dp->convert_to_dp_mode(dp, bridge->dp_panel, mode, &dp_mode); |
| convert_to_drm_mode(&dp_mode, adjusted_mode); |
| end: |
| return ret; |
| } |
| |
| static const struct drm_bridge_funcs dp_bridge_ops = { |
| .attach = dp_bridge_attach, |
| .mode_fixup = dp_bridge_mode_fixup, |
| .pre_enable = dp_bridge_pre_enable, |
| .enable = dp_bridge_enable, |
| .disable = dp_bridge_disable, |
| .post_disable = dp_bridge_post_disable, |
| .mode_set = dp_bridge_mode_set, |
| }; |
| |
| int dp_connector_config_hdr(struct drm_connector *connector, void *display, |
| struct sde_connector_state *c_state) |
| { |
| struct dp_display *dp = display; |
| struct sde_connector *sde_conn; |
| |
| if (!display || !c_state || !connector) { |
| pr_err("invalid params\n"); |
| return -EINVAL; |
| } |
| |
| sde_conn = to_sde_connector(connector); |
| if (!sde_conn->drv_panel) { |
| pr_err("invalid dp panel\n"); |
| return -EINVAL; |
| } |
| |
| return dp->config_hdr(dp, sde_conn->drv_panel, &c_state->hdr_meta, |
| c_state->dyn_hdr_meta.dynamic_hdr_update); |
| } |
| |
| int dp_connector_post_init(struct drm_connector *connector, void *display) |
| { |
| int rc; |
| struct dp_display *dp_display = display; |
| struct sde_connector *sde_conn; |
| |
| if (!dp_display || !connector) |
| return -EINVAL; |
| |
| dp_display->base_connector = connector; |
| dp_display->bridge->connector = connector; |
| |
| if (dp_display->post_init) { |
| rc = dp_display->post_init(dp_display); |
| if (rc) |
| goto end; |
| } |
| |
| sde_conn = to_sde_connector(connector); |
| dp_display->bridge->dp_panel = sde_conn->drv_panel; |
| |
| rc = dp_mst_init(dp_display); |
| end: |
| return rc; |
| } |
| |
| int dp_connector_get_mode_info(struct drm_connector *connector, |
| const struct drm_display_mode *drm_mode, |
| struct msm_mode_info *mode_info, |
| u32 max_mixer_width, void *display) |
| { |
| const u32 dual_lm = 2; |
| const u32 single_lm = 1; |
| const u32 single_intf = 1; |
| const u32 no_enc = 0; |
| struct msm_display_topology *topology; |
| struct sde_connector *sde_conn; |
| struct dp_panel *dp_panel; |
| struct dp_display_mode dp_mode; |
| struct dp_display *dp_disp = display; |
| |
| if (!drm_mode || !mode_info || !max_mixer_width || !connector || |
| !display) { |
| pr_err("invalid params\n"); |
| return -EINVAL; |
| } |
| |
| memset(mode_info, 0, sizeof(*mode_info)); |
| |
| sde_conn = to_sde_connector(connector); |
| dp_panel = sde_conn->drv_panel; |
| |
| topology = &mode_info->topology; |
| topology->num_lm = (max_mixer_width <= drm_mode->hdisplay) ? |
| dual_lm : single_lm; |
| topology->num_enc = no_enc; |
| topology->num_intf = single_intf; |
| |
| mode_info->frame_rate = drm_mode->vrefresh; |
| mode_info->vtotal = drm_mode->vtotal; |
| |
| mode_info->wide_bus_en = dp_panel->widebus_en; |
| |
| dp_disp->convert_to_dp_mode(dp_disp, dp_panel, drm_mode, &dp_mode); |
| |
| if (dp_mode.timing.comp_info.comp_ratio) { |
| memcpy(&mode_info->comp_info, |
| &dp_mode.timing.comp_info, |
| sizeof(mode_info->comp_info)); |
| |
| topology->num_enc = topology->num_lm; |
| } |
| |
| return 0; |
| } |
| |
| int dp_connector_get_info(struct drm_connector *connector, |
| struct msm_display_info *info, void *data) |
| { |
| struct dp_display *display = data; |
| |
| if (!info || !display || !display->drm_dev) { |
| pr_err("invalid params\n"); |
| return -EINVAL; |
| } |
| |
| info->intf_type = DRM_MODE_CONNECTOR_DisplayPort; |
| |
| info->num_of_h_tiles = 1; |
| info->h_tile_instance[0] = 0; |
| info->is_connected = display->is_sst_connected; |
| info->capabilities = MSM_DISPLAY_CAP_VID_MODE | MSM_DISPLAY_CAP_EDID | |
| MSM_DISPLAY_CAP_HOT_PLUG; |
| |
| return 0; |
| } |
| |
| enum drm_connector_status dp_connector_detect(struct drm_connector *conn, |
| bool force, |
| void *display) |
| { |
| enum drm_connector_status status = connector_status_unknown; |
| struct msm_display_info info; |
| int rc; |
| |
| if (!conn || !display) |
| return status; |
| |
| /* get display dp_info */ |
| memset(&info, 0x0, sizeof(info)); |
| rc = dp_connector_get_info(conn, &info, display); |
| if (rc) { |
| pr_err("failed to get display info, rc=%d\n", rc); |
| return connector_status_disconnected; |
| } |
| |
| if (info.capabilities & MSM_DISPLAY_CAP_HOT_PLUG) |
| status = (info.is_connected ? connector_status_connected : |
| connector_status_disconnected); |
| else |
| status = connector_status_connected; |
| |
| conn->display_info.width_mm = info.width_mm; |
| conn->display_info.height_mm = info.height_mm; |
| |
| return status; |
| } |
| |
| void dp_connector_post_open(struct drm_connector *connector, void *display) |
| { |
| struct dp_display *dp; |
| |
| if (!display) { |
| pr_err("invalid input\n"); |
| return; |
| } |
| |
| dp = display; |
| |
| if (dp->post_open) |
| dp->post_open(dp); |
| } |
| |
| int dp_connector_get_modes(struct drm_connector *connector, |
| void *display) |
| { |
| int rc = 0; |
| struct dp_display *dp; |
| struct dp_display_mode *dp_mode = NULL; |
| struct drm_display_mode *m, drm_mode; |
| struct sde_connector *sde_conn; |
| |
| if (!connector || !display) |
| return 0; |
| |
| sde_conn = to_sde_connector(connector); |
| if (!sde_conn->drv_panel) { |
| pr_err("invalid dp panel\n"); |
| return 0; |
| } |
| |
| dp = display; |
| |
| dp_mode = kzalloc(sizeof(*dp_mode), GFP_KERNEL); |
| if (!dp_mode) |
| return 0; |
| |
| /* pluggable case assumes EDID is read when HPD */ |
| if (dp->is_sst_connected) { |
| rc = dp->get_modes(dp, sde_conn->drv_panel, dp_mode); |
| if (!rc) |
| pr_err("failed to get DP sink modes, rc=%d\n", rc); |
| |
| if (dp_mode->timing.pixel_clk_khz) { /* valid DP mode */ |
| memset(&drm_mode, 0x0, sizeof(drm_mode)); |
| convert_to_drm_mode(dp_mode, &drm_mode); |
| m = drm_mode_duplicate(connector->dev, &drm_mode); |
| if (!m) { |
| pr_err("failed to add mode %ux%u\n", |
| drm_mode.hdisplay, |
| drm_mode.vdisplay); |
| kfree(dp_mode); |
| return 0; |
| } |
| m->width_mm = connector->display_info.width_mm; |
| m->height_mm = connector->display_info.height_mm; |
| drm_mode_probed_add(connector, m); |
| } |
| } else { |
| pr_err("No sink connected\n"); |
| } |
| kfree(dp_mode); |
| |
| return rc; |
| } |
| |
| int dp_drm_bridge_init(void *data, struct drm_encoder *encoder) |
| { |
| int rc = 0; |
| struct dp_bridge *bridge; |
| struct drm_device *dev; |
| struct dp_display *display = data; |
| struct msm_drm_private *priv = NULL; |
| |
| bridge = kzalloc(sizeof(*bridge), GFP_KERNEL); |
| if (!bridge) { |
| rc = -ENOMEM; |
| goto error; |
| } |
| |
| dev = display->drm_dev; |
| bridge->display = display; |
| bridge->base.funcs = &dp_bridge_ops; |
| bridge->base.encoder = encoder; |
| |
| priv = dev->dev_private; |
| |
| rc = drm_bridge_attach(encoder, &bridge->base, NULL); |
| if (rc) { |
| pr_err("failed to attach bridge, rc=%d\n", rc); |
| goto error_free_bridge; |
| } |
| |
| rc = display->request_irq(display); |
| if (rc) { |
| pr_err("request_irq failed, rc=%d\n", rc); |
| goto error_free_bridge; |
| } |
| |
| encoder->bridge = &bridge->base; |
| priv->bridges[priv->num_bridges++] = &bridge->base; |
| display->bridge = bridge; |
| |
| return 0; |
| error_free_bridge: |
| kfree(bridge); |
| error: |
| return rc; |
| } |
| |
| void dp_drm_bridge_deinit(void *data) |
| { |
| struct dp_display *display = data; |
| struct dp_bridge *bridge = display->bridge; |
| |
| if (bridge && bridge->base.encoder) |
| bridge->base.encoder->bridge = NULL; |
| |
| kfree(bridge); |
| } |
| |
| enum drm_mode_status dp_connector_mode_valid(struct drm_connector *connector, |
| struct drm_display_mode *mode, void *display) |
| { |
| struct dp_display *dp_disp; |
| struct sde_connector *sde_conn; |
| |
| if (!mode || !display || !connector) { |
| pr_err("invalid params\n"); |
| return MODE_ERROR; |
| } |
| |
| sde_conn = to_sde_connector(connector); |
| if (!sde_conn->drv_panel) { |
| pr_err("invalid dp panel\n"); |
| return MODE_ERROR; |
| } |
| |
| dp_disp = display; |
| mode->vrefresh = drm_mode_vrefresh(mode); |
| |
| return dp_disp->validate_mode(dp_disp, sde_conn->drv_panel, mode); |
| } |
| |
| int dp_connector_update_pps(struct drm_connector *connector, |
| char *pps_cmd, void *display) |
| { |
| struct dp_display *dp_disp; |
| struct sde_connector *sde_conn; |
| |
| if (!display || !connector) { |
| pr_err("invalid params\n"); |
| return -EINVAL; |
| } |
| |
| sde_conn = to_sde_connector(connector); |
| if (!sde_conn->drv_panel) { |
| pr_err("invalid dp panel\n"); |
| return MODE_ERROR; |
| } |
| |
| dp_disp = display; |
| return dp_disp->update_pps(dp_disp, connector, pps_cmd); |
| } |