| /* |
| * driver for NXP USB Host devices |
| * |
| * Currently supported OHCI host devices: |
| * - NXP LPC32xx |
| * |
| * Authors: Dmitry Chigirev <source@mvista.com> |
| * Vitaly Wool <vitalywool@gmail.com> |
| * |
| * register initialization is based on code examples provided by Philips |
| * Copyright (c) 2005 Koninklijke Philips Electronics N.V. |
| * |
| * NOTE: This driver does not have suspend/resume functionality |
| * This driver is intended for engineering development purposes only |
| * |
| * 2005-2006 (c) MontaVista Software, Inc. This file is licensed under |
| * the terms of the GNU General Public License version 2. This program |
| * is licensed "as is" without any warranty of any kind, whether express |
| * or implied. |
| */ |
| #include <linux/clk.h> |
| #include <linux/platform_device.h> |
| #include <linux/i2c.h> |
| #include <linux/of.h> |
| #include <linux/usb/isp1301.h> |
| |
| #include <mach/hardware.h> |
| #include <asm/mach-types.h> |
| #include <asm/io.h> |
| |
| #include <mach/platform.h> |
| #include <mach/irqs.h> |
| |
| #define USB_CONFIG_BASE 0x31020000 |
| #define PWRMAN_BASE 0x40004000 |
| |
| #define USB_CTRL IO_ADDRESS(PWRMAN_BASE + 0x64) |
| |
| /* USB_CTRL bit defines */ |
| #define USB_SLAVE_HCLK_EN (1 << 24) |
| #define USB_DEV_NEED_CLK_EN (1 << 22) |
| #define USB_HOST_NEED_CLK_EN (1 << 21) |
| #define PAD_CONTROL_LAST_DRIVEN (1 << 19) |
| |
| #define USB_OTG_STAT_CONTROL IO_ADDRESS(USB_CONFIG_BASE + 0x110) |
| |
| /* USB_OTG_STAT_CONTROL bit defines */ |
| #define TRANSPARENT_I2C_EN (1 << 7) |
| #define HOST_EN (1 << 0) |
| |
| /* On LPC32xx, those are undefined */ |
| #ifndef start_int_set_falling_edge |
| #define start_int_set_falling_edge(irq) |
| #define start_int_set_rising_edge(irq) |
| #define start_int_ack(irq) |
| #define start_int_mask(irq) |
| #define start_int_umask(irq) |
| #endif |
| |
| static struct i2c_client *isp1301_i2c_client; |
| |
| extern int usb_disabled(void); |
| |
| static struct clk *usb_pll_clk; |
| static struct clk *usb_dev_clk; |
| static struct clk *usb_otg_clk; |
| |
| static void isp1301_configure_lpc32xx(void) |
| { |
| /* LPC32XX only supports DAT_SE0 USB mode */ |
| /* This sequence is important */ |
| |
| /* Disable transparent UART mode first */ |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), |
| MC1_UART_EN); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), |
| ~MC1_SPEED_REG); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_MODE_CONTROL_1, MC1_SPEED_REG); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| (ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR), |
| ~0); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_MODE_CONTROL_2, |
| (MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL)); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), ~0); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_MODE_CONTROL_1, MC1_DAT_SE0); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_OTG_CONTROL_1, |
| (OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN)); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), |
| (OTG1_DM_PULLUP | OTG1_DP_PULLUP)); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR, ~0); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR, |
| ~0); |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR, ~0); |
| |
| /* Enable usb_need_clk clock after transceiver is initialized */ |
| __raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL); |
| |
| printk(KERN_INFO "ISP1301 Vendor ID : 0x%04x\n", |
| i2c_smbus_read_word_data(isp1301_i2c_client, 0x00)); |
| printk(KERN_INFO "ISP1301 Product ID : 0x%04x\n", |
| i2c_smbus_read_word_data(isp1301_i2c_client, 0x02)); |
| printk(KERN_INFO "ISP1301 Version ID : 0x%04x\n", |
| i2c_smbus_read_word_data(isp1301_i2c_client, 0x14)); |
| } |
| |
| static void isp1301_configure(void) |
| { |
| isp1301_configure_lpc32xx(); |
| } |
| |
| static inline void isp1301_vbus_on(void) |
| { |
| i2c_smbus_write_byte_data(isp1301_i2c_client, ISP1301_I2C_OTG_CONTROL_1, |
| OTG1_VBUS_DRV); |
| } |
| |
| static inline void isp1301_vbus_off(void) |
| { |
| i2c_smbus_write_byte_data(isp1301_i2c_client, |
| ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR, |
| OTG1_VBUS_DRV); |
| } |
| |
| static void nxp_start_hc(void) |
| { |
| unsigned long tmp = __raw_readl(USB_OTG_STAT_CONTROL) | HOST_EN; |
| __raw_writel(tmp, USB_OTG_STAT_CONTROL); |
| isp1301_vbus_on(); |
| } |
| |
| static void nxp_stop_hc(void) |
| { |
| unsigned long tmp; |
| isp1301_vbus_off(); |
| tmp = __raw_readl(USB_OTG_STAT_CONTROL) & ~HOST_EN; |
| __raw_writel(tmp, USB_OTG_STAT_CONTROL); |
| } |
| |
| static int __devinit ohci_nxp_start(struct usb_hcd *hcd) |
| { |
| struct ohci_hcd *ohci = hcd_to_ohci(hcd); |
| int ret; |
| |
| if ((ret = ohci_init(ohci)) < 0) |
| return ret; |
| |
| if ((ret = ohci_run(ohci)) < 0) { |
| dev_err(hcd->self.controller, "can't start\n"); |
| ohci_stop(hcd); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static const struct hc_driver ohci_nxp_hc_driver = { |
| .description = hcd_name, |
| .product_desc = "nxp OHCI", |
| |
| /* |
| * generic hardware linkage |
| */ |
| .irq = ohci_irq, |
| .flags = HCD_USB11 | HCD_MEMORY, |
| |
| .hcd_priv_size = sizeof(struct ohci_hcd), |
| /* |
| * basic lifecycle operations |
| */ |
| .start = ohci_nxp_start, |
| .stop = ohci_stop, |
| .shutdown = ohci_shutdown, |
| |
| /* |
| * managing i/o requests and associated device resources |
| */ |
| .urb_enqueue = ohci_urb_enqueue, |
| .urb_dequeue = ohci_urb_dequeue, |
| .endpoint_disable = ohci_endpoint_disable, |
| |
| /* |
| * scheduling support |
| */ |
| .get_frame_number = ohci_get_frame, |
| |
| /* |
| * root hub support |
| */ |
| .hub_status_data = ohci_hub_status_data, |
| .hub_control = ohci_hub_control, |
| #ifdef CONFIG_PM |
| .bus_suspend = ohci_bus_suspend, |
| .bus_resume = ohci_bus_resume, |
| #endif |
| .start_port_reset = ohci_start_port_reset, |
| }; |
| |
| static int __devinit usb_hcd_nxp_probe(struct platform_device *pdev) |
| { |
| struct usb_hcd *hcd = 0; |
| struct ohci_hcd *ohci; |
| const struct hc_driver *driver = &ohci_nxp_hc_driver; |
| struct resource *res; |
| int ret = 0, irq; |
| struct device_node *isp1301_node; |
| |
| if (pdev->dev.of_node) { |
| isp1301_node = of_parse_phandle(pdev->dev.of_node, |
| "transceiver", 0); |
| } else { |
| isp1301_node = NULL; |
| } |
| |
| isp1301_i2c_client = isp1301_get_client(isp1301_node); |
| if (!isp1301_i2c_client) { |
| ret = -EPROBE_DEFER; |
| goto out; |
| } |
| |
| pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32); |
| pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; |
| |
| dev_dbg(&pdev->dev, "%s: " DRIVER_DESC " (nxp)\n", hcd_name); |
| if (usb_disabled()) { |
| dev_err(&pdev->dev, "USB is disabled\n"); |
| ret = -ENODEV; |
| goto out; |
| } |
| |
| /* Enable AHB slave USB clock, needed for further USB clock control */ |
| __raw_writel(USB_SLAVE_HCLK_EN | PAD_CONTROL_LAST_DRIVEN, USB_CTRL); |
| |
| /* Enable USB PLL */ |
| usb_pll_clk = clk_get(&pdev->dev, "ck_pll5"); |
| if (IS_ERR(usb_pll_clk)) { |
| dev_err(&pdev->dev, "failed to acquire USB PLL\n"); |
| ret = PTR_ERR(usb_pll_clk); |
| goto out1; |
| } |
| |
| ret = clk_enable(usb_pll_clk); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to start USB PLL\n"); |
| goto out2; |
| } |
| |
| ret = clk_set_rate(usb_pll_clk, 48000); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to set USB clock rate\n"); |
| goto out3; |
| } |
| |
| /* Enable USB device clock */ |
| usb_dev_clk = clk_get(&pdev->dev, "ck_usbd"); |
| if (IS_ERR(usb_dev_clk)) { |
| dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n"); |
| ret = PTR_ERR(usb_dev_clk); |
| goto out4; |
| } |
| |
| ret = clk_enable(usb_dev_clk); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to start USB DEV Clock\n"); |
| goto out5; |
| } |
| |
| /* Enable USB otg clocks */ |
| usb_otg_clk = clk_get(&pdev->dev, "ck_usb_otg"); |
| if (IS_ERR(usb_otg_clk)) { |
| dev_err(&pdev->dev, "failed to acquire USB DEV Clock\n"); |
| ret = PTR_ERR(usb_dev_clk); |
| goto out6; |
| } |
| |
| __raw_writel(__raw_readl(USB_CTRL) | USB_HOST_NEED_CLK_EN, USB_CTRL); |
| |
| ret = clk_enable(usb_otg_clk); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to start USB DEV Clock\n"); |
| goto out7; |
| } |
| |
| isp1301_configure(); |
| |
| hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); |
| if (!hcd) { |
| dev_err(&pdev->dev, "Failed to allocate HC buffer\n"); |
| ret = -ENOMEM; |
| goto out8; |
| } |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!res) { |
| dev_err(&pdev->dev, "Failed to get MEM resource\n"); |
| ret = -ENOMEM; |
| goto out8; |
| } |
| |
| hcd->regs = devm_request_and_ioremap(&pdev->dev, res); |
| if (!hcd->regs) { |
| dev_err(&pdev->dev, "Failed to devm_request_and_ioremap\n"); |
| ret = -ENOMEM; |
| goto out8; |
| } |
| hcd->rsrc_start = res->start; |
| hcd->rsrc_len = resource_size(res); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) { |
| ret = -ENXIO; |
| goto out8; |
| } |
| |
| nxp_start_hc(); |
| platform_set_drvdata(pdev, hcd); |
| ohci = hcd_to_ohci(hcd); |
| ohci_hcd_init(ohci); |
| |
| dev_info(&pdev->dev, "at 0x%p, irq %d\n", hcd->regs, hcd->irq); |
| ret = usb_add_hcd(hcd, irq, 0); |
| if (ret == 0) |
| return ret; |
| |
| nxp_stop_hc(); |
| out8: |
| usb_put_hcd(hcd); |
| out7: |
| clk_disable(usb_otg_clk); |
| out6: |
| clk_put(usb_otg_clk); |
| out5: |
| clk_disable(usb_dev_clk); |
| out4: |
| clk_put(usb_dev_clk); |
| out3: |
| clk_disable(usb_pll_clk); |
| out2: |
| clk_put(usb_pll_clk); |
| out1: |
| isp1301_i2c_client = NULL; |
| out: |
| return ret; |
| } |
| |
| static int usb_hcd_nxp_remove(struct platform_device *pdev) |
| { |
| struct usb_hcd *hcd = platform_get_drvdata(pdev); |
| |
| usb_remove_hcd(hcd); |
| nxp_stop_hc(); |
| release_mem_region(hcd->rsrc_start, hcd->rsrc_len); |
| usb_put_hcd(hcd); |
| clk_disable(usb_pll_clk); |
| clk_put(usb_pll_clk); |
| clk_disable(usb_dev_clk); |
| clk_put(usb_dev_clk); |
| i2c_unregister_device(isp1301_i2c_client); |
| isp1301_i2c_client = NULL; |
| |
| platform_set_drvdata(pdev, NULL); |
| |
| return 0; |
| } |
| |
| /* work with hotplug and coldplug */ |
| MODULE_ALIAS("platform:usb-ohci"); |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id usb_hcd_nxp_match[] = { |
| { .compatible = "nxp,ohci-nxp" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, usb_hcd_nxp_match); |
| #endif |
| |
| static struct platform_driver usb_hcd_nxp_driver = { |
| .driver = { |
| .name = "usb-ohci", |
| .owner = THIS_MODULE, |
| .of_match_table = of_match_ptr(usb_hcd_nxp_match), |
| }, |
| .probe = usb_hcd_nxp_probe, |
| .remove = usb_hcd_nxp_remove, |
| }; |
| |