| /* |
| * core.c - DesignWare HS OTG Controller common routines |
| * |
| * Copyright (C) 2004-2013 Synopsys, Inc. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * 1. Redistributions of source code must retain the above copyright |
| * notice, this list of conditions, and the following disclaimer, |
| * without modification. |
| * 2. Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in the |
| * documentation and/or other materials provided with the distribution. |
| * 3. The names of the above-listed copyright holders may not be used |
| * to endorse or promote products derived from this software without |
| * specific prior written permission. |
| * |
| * ALTERNATIVELY, this software may be distributed under the terms of the |
| * GNU General Public License ("GPL") as published by the Free Software |
| * Foundation; either version 2 of the License, or (at your option) any |
| * later version. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS |
| * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, |
| * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR |
| * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR |
| * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, |
| * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, |
| * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR |
| * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF |
| * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING |
| * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS |
| * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| /* |
| * The Core code provides basic services for accessing and managing the |
| * DWC_otg hardware. These services are used by both the Host Controller |
| * Driver and the Peripheral Controller Driver. |
| */ |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/spinlock.h> |
| #include <linux/interrupt.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/delay.h> |
| #include <linux/io.h> |
| #include <linux/slab.h> |
| #include <linux/usb.h> |
| |
| #include <linux/usb/hcd.h> |
| #include <linux/usb/ch11.h> |
| |
| #include "core.h" |
| #include "hcd.h" |
| |
| /** |
| * dwc2_backup_global_registers() - Backup global controller registers. |
| * When suspending usb bus, registers needs to be backuped |
| * if controller power is disabled once suspended. |
| * |
| * @hsotg: Programming view of the DWC_otg controller |
| */ |
| static int dwc2_backup_global_registers(struct dwc2_hsotg *hsotg) |
| { |
| struct dwc2_gregs_backup *gr; |
| int i; |
| |
| /* Backup global regs */ |
| gr = &hsotg->gr_backup; |
| |
| gr->gotgctl = dwc2_readl(hsotg->regs + GOTGCTL); |
| gr->gintmsk = dwc2_readl(hsotg->regs + GINTMSK); |
| gr->gahbcfg = dwc2_readl(hsotg->regs + GAHBCFG); |
| gr->gusbcfg = dwc2_readl(hsotg->regs + GUSBCFG); |
| gr->grxfsiz = dwc2_readl(hsotg->regs + GRXFSIZ); |
| gr->gnptxfsiz = dwc2_readl(hsotg->regs + GNPTXFSIZ); |
| gr->hptxfsiz = dwc2_readl(hsotg->regs + HPTXFSIZ); |
| gr->gdfifocfg = dwc2_readl(hsotg->regs + GDFIFOCFG); |
| for (i = 0; i < MAX_EPS_CHANNELS; i++) |
| gr->dtxfsiz[i] = dwc2_readl(hsotg->regs + DPTXFSIZN(i)); |
| |
| gr->valid = true; |
| return 0; |
| } |
| |
| /** |
| * dwc2_restore_global_registers() - Restore controller global registers. |
| * When resuming usb bus, device registers needs to be restored |
| * if controller power were disabled. |
| * |
| * @hsotg: Programming view of the DWC_otg controller |
| */ |
| static int dwc2_restore_global_registers(struct dwc2_hsotg *hsotg) |
| { |
| struct dwc2_gregs_backup *gr; |
| int i; |
| |
| dev_dbg(hsotg->dev, "%s\n", __func__); |
| |
| /* Restore global regs */ |
| gr = &hsotg->gr_backup; |
| if (!gr->valid) { |
| dev_err(hsotg->dev, "%s: no global registers to restore\n", |
| __func__); |
| return -EINVAL; |
| } |
| gr->valid = false; |
| |
| dwc2_writel(0xffffffff, hsotg->regs + GINTSTS); |
| dwc2_writel(gr->gotgctl, hsotg->regs + GOTGCTL); |
| dwc2_writel(gr->gintmsk, hsotg->regs + GINTMSK); |
| dwc2_writel(gr->gusbcfg, hsotg->regs + GUSBCFG); |
| dwc2_writel(gr->gahbcfg, hsotg->regs + GAHBCFG); |
| dwc2_writel(gr->grxfsiz, hsotg->regs + GRXFSIZ); |
| dwc2_writel(gr->gnptxfsiz, hsotg->regs + GNPTXFSIZ); |
| dwc2_writel(gr->hptxfsiz, hsotg->regs + HPTXFSIZ); |
| dwc2_writel(gr->gdfifocfg, hsotg->regs + GDFIFOCFG); |
| for (i = 0; i < MAX_EPS_CHANNELS; i++) |
| dwc2_writel(gr->dtxfsiz[i], hsotg->regs + DPTXFSIZN(i)); |
| |
| return 0; |
| } |
| |
| /** |
| * dwc2_exit_hibernation() - Exit controller from Partial Power Down. |
| * |
| * @hsotg: Programming view of the DWC_otg controller |
| * @restore: Controller registers need to be restored |
| */ |
| int dwc2_exit_hibernation(struct dwc2_hsotg *hsotg, bool restore) |
| { |
| u32 pcgcctl; |
| int ret = 0; |
| |
| if (!hsotg->core_params->hibernation) |
| return -ENOTSUPP; |
| |
| pcgcctl = dwc2_readl(hsotg->regs + PCGCTL); |
| pcgcctl &= ~PCGCTL_STOPPCLK; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| |
| pcgcctl = dwc2_readl(hsotg->regs + PCGCTL); |
| pcgcctl &= ~PCGCTL_PWRCLMP; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| |
| pcgcctl = dwc2_readl(hsotg->regs + PCGCTL); |
| pcgcctl &= ~PCGCTL_RSTPDWNMODULE; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| |
| udelay(100); |
| if (restore) { |
| ret = dwc2_restore_global_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to restore registers\n", |
| __func__); |
| return ret; |
| } |
| if (dwc2_is_host_mode(hsotg)) { |
| ret = dwc2_restore_host_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to restore host registers\n", |
| __func__); |
| return ret; |
| } |
| } else { |
| ret = dwc2_restore_device_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to restore device registers\n", |
| __func__); |
| return ret; |
| } |
| } |
| } |
| |
| return ret; |
| } |
| |
| /** |
| * dwc2_enter_hibernation() - Put controller in Partial Power Down. |
| * |
| * @hsotg: Programming view of the DWC_otg controller |
| */ |
| int dwc2_enter_hibernation(struct dwc2_hsotg *hsotg) |
| { |
| u32 pcgcctl; |
| int ret = 0; |
| |
| if (!hsotg->core_params->hibernation) |
| return -ENOTSUPP; |
| |
| /* Backup all registers */ |
| ret = dwc2_backup_global_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to backup global registers\n", |
| __func__); |
| return ret; |
| } |
| |
| if (dwc2_is_host_mode(hsotg)) { |
| ret = dwc2_backup_host_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to backup host registers\n", |
| __func__); |
| return ret; |
| } |
| } else { |
| ret = dwc2_backup_device_registers(hsotg); |
| if (ret) { |
| dev_err(hsotg->dev, "%s: failed to backup device registers\n", |
| __func__); |
| return ret; |
| } |
| } |
| |
| /* |
| * Clear any pending interrupts since dwc2 will not be able to |
| * clear them after entering hibernation. |
| */ |
| dwc2_writel(0xffffffff, hsotg->regs + GINTSTS); |
| |
| /* Put the controller in low power state */ |
| pcgcctl = dwc2_readl(hsotg->regs + PCGCTL); |
| |
| pcgcctl |= PCGCTL_PWRCLMP; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| ndelay(20); |
| |
| pcgcctl |= PCGCTL_RSTPDWNMODULE; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| ndelay(20); |
| |
| pcgcctl |= PCGCTL_STOPPCLK; |
| dwc2_writel(pcgcctl, hsotg->regs + PCGCTL); |
| |
| return ret; |
| } |
| |
| /** |
| * dwc2_wait_for_mode() - Waits for the controller mode. |
| * @hsotg: Programming view of the DWC_otg controller. |
| * @host_mode: If true, waits for host mode, otherwise device mode. |
| */ |
| static void dwc2_wait_for_mode(struct dwc2_hsotg *hsotg, |
| bool host_mode) |
| { |
| ktime_t start; |
| ktime_t end; |
| unsigned int timeout = 110; |
| |
| dev_vdbg(hsotg->dev, "Waiting for %s mode\n", |
| host_mode ? "host" : "device"); |
| |
| start = ktime_get(); |
| |
| while (1) { |
| s64 ms; |
| |
| if (dwc2_is_host_mode(hsotg) == host_mode) { |
| dev_vdbg(hsotg->dev, "%s mode set\n", |
| host_mode ? "Host" : "Device"); |
| break; |
| } |
| |
| end = ktime_get(); |
| ms = ktime_to_ms(ktime_sub(end, start)); |
| |
| if (ms >= (s64)timeout) { |
| dev_warn(hsotg->dev, "%s: Couldn't set %s mode\n", |
| __func__, host_mode ? "host" : "device"); |
| break; |
| } |
| |
| usleep_range(1000, 2000); |
| } |
| } |
| |
| /** |
| * dwc2_iddig_filter_enabled() - Returns true if the IDDIG debounce |
| * filter is enabled. |
| */ |
| static bool dwc2_iddig_filter_enabled(struct dwc2_hsotg *hsotg) |
| { |
| u32 gsnpsid; |
| u32 ghwcfg4; |
| |
| if (!dwc2_hw_is_otg(hsotg)) |
| return false; |
| |
| /* Check if core configuration includes the IDDIG filter. */ |
| ghwcfg4 = dwc2_readl(hsotg->regs + GHWCFG4); |
| if (!(ghwcfg4 & GHWCFG4_IDDIG_FILT_EN)) |
| return false; |
| |
| /* |
| * Check if the IDDIG debounce filter is bypassed. Available |
| * in core version >= 3.10a. |
| */ |
| gsnpsid = dwc2_readl(hsotg->regs + GSNPSID); |
| if (gsnpsid >= DWC2_CORE_REV_3_10a) { |
| u32 gotgctl = dwc2_readl(hsotg->regs + GOTGCTL); |
| |
| if (gotgctl & GOTGCTL_DBNCE_FLTR_BYPASS) |
| return false; |
| } |
| |
| return true; |
| } |
| |
| /* |
| * Do core a soft reset of the core. Be careful with this because it |
| * resets all the internal state machines of the core. |
| */ |
| int dwc2_core_reset(struct dwc2_hsotg *hsotg) |
| { |
| u32 greset; |
| int count = 0; |
| bool wait_for_host_mode = false; |
| |
| dev_vdbg(hsotg->dev, "%s()\n", __func__); |
| |
| /* |
| * If the current mode is host, either due to the force mode |
| * bit being set (which persists after core reset) or the |
| * connector id pin, a core soft reset will temporarily reset |
| * the mode to device. A delay from the IDDIG debounce filter |
| * will occur before going back to host mode. |
| * |
| * Determine whether we will go back into host mode after a |
| * reset and account for this delay after the reset. |
| */ |
| if (dwc2_iddig_filter_enabled(hsotg)) { |
| u32 gotgctl = dwc2_readl(hsotg->regs + GOTGCTL); |
| u32 gusbcfg = dwc2_readl(hsotg->regs + GUSBCFG); |
| |
| if (!(gotgctl & GOTGCTL_CONID_B) || |
| (gusbcfg & GUSBCFG_FORCEHOSTMODE)) { |
| wait_for_host_mode = true; |
| } |
| } |
| |
| /* Core Soft Reset */ |
| greset = dwc2_readl(hsotg->regs + GRSTCTL); |
| greset |= GRSTCTL_CSFTRST; |
| dwc2_writel(greset, hsotg->regs + GRSTCTL); |
| do { |
| udelay(1); |
| greset = dwc2_readl(hsotg->regs + GRSTCTL); |
| if (++count > 50) { |
| dev_warn(hsotg->dev, |
| "%s() HANG! Soft Reset GRSTCTL=%0x\n", |
| __func__, greset); |
| return -EBUSY; |
| } |
| } while (greset & GRSTCTL_CSFTRST); |
| |
| /* Wait for AHB master IDLE state */ |
| count = 0; |
| do { |
| udelay(1); |
| greset = dwc2_readl(hsotg->regs + GRSTCTL); |
| if (++count > 50) { |
| dev_warn(hsotg->dev, |
| "%s() HANG! AHB Idle GRSTCTL=%0x\n", |
| __func__, greset); |
| return -EBUSY; |
| } |
| } while (!(greset & GRSTCTL_AHBIDLE)); |
| |
| if (wait_for_host_mode) |
| dwc2_wait_for_mode(hsotg, true); |
| |
| return 0; |
| } |
| |
| /* |
| * Force the mode of the controller. |
| * |
| * Forcing the mode is needed for two cases: |
| * |
| * 1) If the dr_mode is set to either HOST or PERIPHERAL we force the |
| * controller to stay in a particular mode regardless of ID pin |
| * changes. We do this usually after a core reset. |
| * |
| * 2) During probe we want to read reset values of the hw |
| * configuration registers that are only available in either host or |
| * device mode. We may need to force the mode if the current mode does |
| * not allow us to access the register in the mode that we want. |
| * |
| * In either case it only makes sense to force the mode if the |
| * controller hardware is OTG capable. |
| * |
| * Checks are done in this function to determine whether doing a force |
| * would be valid or not. |
| * |
| * If a force is done, it requires a IDDIG debounce filter delay if |
| * the filter is configured and enabled. We poll the current mode of |
| * the controller to account for this delay. |
| */ |
| static bool dwc2_force_mode(struct dwc2_hsotg *hsotg, bool host) |
| { |
| u32 gusbcfg; |
| u32 set; |
| u32 clear; |
| |
| dev_dbg(hsotg->dev, "Forcing mode to %s\n", host ? "host" : "device"); |
| |
| /* |
| * Force mode has no effect if the hardware is not OTG. |
| */ |
| if (!dwc2_hw_is_otg(hsotg)) |
| return false; |
| |
| /* |
| * If dr_mode is either peripheral or host only, there is no |
| * need to ever force the mode to the opposite mode. |
| */ |
| if (WARN_ON(host && hsotg->dr_mode == USB_DR_MODE_PERIPHERAL)) |
| return false; |
| |
| if (WARN_ON(!host && hsotg->dr_mode == USB_DR_MODE_HOST)) |
| return false; |
| |
| gusbcfg = dwc2_readl(hsotg->regs + GUSBCFG); |
| |
| set = host ? GUSBCFG_FORCEHOSTMODE : GUSBCFG_FORCEDEVMODE; |
| clear = host ? GUSBCFG_FORCEDEVMODE : GUSBCFG_FORCEHOSTMODE; |
| |
| gusbcfg &= ~clear; |
| gusbcfg |= set; |
| dwc2_writel(gusbcfg, hsotg->regs + GUSBCFG); |
| |
| dwc2_wait_for_mode(hsotg, host); |
| return true; |
| } |
| |
| /** |
| * dwc2_clear_force_mode() - Clears the force mode bits. |
| * |
| * After clearing the bits, wait up to 100 ms to account for any |
| * potential IDDIG filter delay. We can't know if we expect this delay |
| * or not because the value of the connector ID status is affected by |
| * the force mode. We only need to call this once during probe if |
| * dr_mode == OTG. |
| */ |
| static void dwc2_clear_force_mode(struct dwc2_hsotg *hsotg) |
| { |
| u32 gusbcfg; |
| |
| gusbcfg = dwc2_readl(hsotg->regs + GUSBCFG); |
| gusbcfg &= ~GUSBCFG_FORCEHOSTMODE; |
| gusbcfg &= ~GUSBCFG_FORCEDEVMODE; |
| dwc2_writel(gusbcfg, hsotg->regs + GUSBCFG); |
| |
| if (dwc2_iddig_filter_enabled(hsotg)) |
| usleep_range(100000, 110000); |
| } |
| |
| /* |
| * Sets or clears force mode based on the dr_mode parameter. |
| */ |
| void dwc2_force_dr_mode(struct dwc2_hsotg *hsotg) |
| { |
| switch (hsotg->dr_mode) { |
| case USB_DR_MODE_HOST: |
| dwc2_force_mode(hsotg, true); |
| break; |
| case USB_DR_MODE_PERIPHERAL: |
| dwc2_force_mode(hsotg, false); |
| break; |
| case USB_DR_MODE_OTG: |
| dwc2_clear_force_mode(hsotg); |
| break; |
| default: |
| dev_warn(hsotg->dev, "%s() Invalid dr_mode=%d\n", |
| __func__, hsotg->dr_mode); |
| break; |
| } |
| } |
| |
| /* |
| * Do core a soft reset of the core. Be careful with this because it |
| * resets all the internal state machines of the core. |
| * |
| * Additionally this will apply force mode as per the hsotg->dr_mode |
| * parameter. |
| */ |
| int dwc2_core_reset_and_force_dr_mode(struct dwc2_hsotg *hsotg) |
| { |
| int retval; |
| |
| retval = dwc2_core_reset(hsotg); |
| if (retval) |
| return retval; |
| |
| dwc2_force_dr_mode(hsotg); |
| return 0; |
| } |
| |
| /** |
| * dwc2_dump_host_registers() - Prints the host registers |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| * |
| * NOTE: This function will be removed once the peripheral controller code |
| * is integrated and the driver is stable |
| */ |
| void dwc2_dump_host_registers(struct dwc2_hsotg *hsotg) |
| { |
| #ifdef DEBUG |
| u32 __iomem *addr; |
| int i; |
| |
| dev_dbg(hsotg->dev, "Host Global Registers\n"); |
| addr = hsotg->regs + HCFG; |
| dev_dbg(hsotg->dev, "HCFG @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HFIR; |
| dev_dbg(hsotg->dev, "HFIR @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HFNUM; |
| dev_dbg(hsotg->dev, "HFNUM @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HPTXSTS; |
| dev_dbg(hsotg->dev, "HPTXSTS @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HAINT; |
| dev_dbg(hsotg->dev, "HAINT @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HAINTMSK; |
| dev_dbg(hsotg->dev, "HAINTMSK @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| if (hsotg->core_params->dma_desc_enable > 0) { |
| addr = hsotg->regs + HFLBADDR; |
| dev_dbg(hsotg->dev, "HFLBADDR @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| } |
| |
| addr = hsotg->regs + HPRT0; |
| dev_dbg(hsotg->dev, "HPRT0 @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| |
| for (i = 0; i < hsotg->core_params->host_channels; i++) { |
| dev_dbg(hsotg->dev, "Host Channel %d Specific Registers\n", i); |
| addr = hsotg->regs + HCCHAR(i); |
| dev_dbg(hsotg->dev, "HCCHAR @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HCSPLT(i); |
| dev_dbg(hsotg->dev, "HCSPLT @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HCINT(i); |
| dev_dbg(hsotg->dev, "HCINT @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HCINTMSK(i); |
| dev_dbg(hsotg->dev, "HCINTMSK @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HCTSIZ(i); |
| dev_dbg(hsotg->dev, "HCTSIZ @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HCDMA(i); |
| dev_dbg(hsotg->dev, "HCDMA @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| if (hsotg->core_params->dma_desc_enable > 0) { |
| addr = hsotg->regs + HCDMAB(i); |
| dev_dbg(hsotg->dev, "HCDMAB @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| } |
| } |
| #endif |
| } |
| |
| /** |
| * dwc2_dump_global_registers() - Prints the core global registers |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| * |
| * NOTE: This function will be removed once the peripheral controller code |
| * is integrated and the driver is stable |
| */ |
| void dwc2_dump_global_registers(struct dwc2_hsotg *hsotg) |
| { |
| #ifdef DEBUG |
| u32 __iomem *addr; |
| |
| dev_dbg(hsotg->dev, "Core Global Registers\n"); |
| addr = hsotg->regs + GOTGCTL; |
| dev_dbg(hsotg->dev, "GOTGCTL @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GOTGINT; |
| dev_dbg(hsotg->dev, "GOTGINT @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GAHBCFG; |
| dev_dbg(hsotg->dev, "GAHBCFG @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GUSBCFG; |
| dev_dbg(hsotg->dev, "GUSBCFG @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GRSTCTL; |
| dev_dbg(hsotg->dev, "GRSTCTL @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GINTSTS; |
| dev_dbg(hsotg->dev, "GINTSTS @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GINTMSK; |
| dev_dbg(hsotg->dev, "GINTMSK @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GRXSTSR; |
| dev_dbg(hsotg->dev, "GRXSTSR @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GRXFSIZ; |
| dev_dbg(hsotg->dev, "GRXFSIZ @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GNPTXFSIZ; |
| dev_dbg(hsotg->dev, "GNPTXFSIZ @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GNPTXSTS; |
| dev_dbg(hsotg->dev, "GNPTXSTS @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GI2CCTL; |
| dev_dbg(hsotg->dev, "GI2CCTL @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GPVNDCTL; |
| dev_dbg(hsotg->dev, "GPVNDCTL @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GGPIO; |
| dev_dbg(hsotg->dev, "GGPIO @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GUID; |
| dev_dbg(hsotg->dev, "GUID @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GSNPSID; |
| dev_dbg(hsotg->dev, "GSNPSID @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GHWCFG1; |
| dev_dbg(hsotg->dev, "GHWCFG1 @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GHWCFG2; |
| dev_dbg(hsotg->dev, "GHWCFG2 @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GHWCFG3; |
| dev_dbg(hsotg->dev, "GHWCFG3 @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GHWCFG4; |
| dev_dbg(hsotg->dev, "GHWCFG4 @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GLPMCFG; |
| dev_dbg(hsotg->dev, "GLPMCFG @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GPWRDN; |
| dev_dbg(hsotg->dev, "GPWRDN @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + GDFIFOCFG; |
| dev_dbg(hsotg->dev, "GDFIFOCFG @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| addr = hsotg->regs + HPTXFSIZ; |
| dev_dbg(hsotg->dev, "HPTXFSIZ @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| |
| addr = hsotg->regs + PCGCTL; |
| dev_dbg(hsotg->dev, "PCGCTL @0x%08lX : 0x%08X\n", |
| (unsigned long)addr, dwc2_readl(addr)); |
| #endif |
| } |
| |
| /** |
| * dwc2_flush_tx_fifo() - Flushes a Tx FIFO |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| * @num: Tx FIFO to flush |
| */ |
| void dwc2_flush_tx_fifo(struct dwc2_hsotg *hsotg, const int num) |
| { |
| u32 greset; |
| int count = 0; |
| |
| dev_vdbg(hsotg->dev, "Flush Tx FIFO %d\n", num); |
| |
| greset = GRSTCTL_TXFFLSH; |
| greset |= num << GRSTCTL_TXFNUM_SHIFT & GRSTCTL_TXFNUM_MASK; |
| dwc2_writel(greset, hsotg->regs + GRSTCTL); |
| |
| do { |
| greset = dwc2_readl(hsotg->regs + GRSTCTL); |
| if (++count > 10000) { |
| dev_warn(hsotg->dev, |
| "%s() HANG! GRSTCTL=%0x GNPTXSTS=0x%08x\n", |
| __func__, greset, |
| dwc2_readl(hsotg->regs + GNPTXSTS)); |
| break; |
| } |
| udelay(1); |
| } while (greset & GRSTCTL_TXFFLSH); |
| |
| /* Wait for at least 3 PHY Clocks */ |
| udelay(1); |
| } |
| |
| /** |
| * dwc2_flush_rx_fifo() - Flushes the Rx FIFO |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| */ |
| void dwc2_flush_rx_fifo(struct dwc2_hsotg *hsotg) |
| { |
| u32 greset; |
| int count = 0; |
| |
| dev_vdbg(hsotg->dev, "%s()\n", __func__); |
| |
| greset = GRSTCTL_RXFFLSH; |
| dwc2_writel(greset, hsotg->regs + GRSTCTL); |
| |
| do { |
| greset = dwc2_readl(hsotg->regs + GRSTCTL); |
| if (++count > 10000) { |
| dev_warn(hsotg->dev, "%s() HANG! GRSTCTL=%0x\n", |
| __func__, greset); |
| break; |
| } |
| udelay(1); |
| } while (greset & GRSTCTL_RXFFLSH); |
| |
| /* Wait for at least 3 PHY Clocks */ |
| udelay(1); |
| } |
| |
| #define DWC2_OUT_OF_BOUNDS(a, b, c) ((a) < (b) || (a) > (c)) |
| |
| /* Parameter access functions */ |
| void dwc2_set_param_otg_cap(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| switch (val) { |
| case DWC2_CAP_PARAM_HNP_SRP_CAPABLE: |
| if (hsotg->hw_params.op_mode != GHWCFG2_OP_MODE_HNP_SRP_CAPABLE) |
| valid = 0; |
| break; |
| case DWC2_CAP_PARAM_SRP_ONLY_CAPABLE: |
| switch (hsotg->hw_params.op_mode) { |
| case GHWCFG2_OP_MODE_HNP_SRP_CAPABLE: |
| case GHWCFG2_OP_MODE_SRP_ONLY_CAPABLE: |
| case GHWCFG2_OP_MODE_SRP_CAPABLE_DEVICE: |
| case GHWCFG2_OP_MODE_SRP_CAPABLE_HOST: |
| break; |
| default: |
| valid = 0; |
| break; |
| } |
| break; |
| case DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE: |
| /* always valid */ |
| break; |
| default: |
| valid = 0; |
| break; |
| } |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for otg_cap parameter. Check HW configuration.\n", |
| val); |
| switch (hsotg->hw_params.op_mode) { |
| case GHWCFG2_OP_MODE_HNP_SRP_CAPABLE: |
| val = DWC2_CAP_PARAM_HNP_SRP_CAPABLE; |
| break; |
| case GHWCFG2_OP_MODE_SRP_ONLY_CAPABLE: |
| case GHWCFG2_OP_MODE_SRP_CAPABLE_DEVICE: |
| case GHWCFG2_OP_MODE_SRP_CAPABLE_HOST: |
| val = DWC2_CAP_PARAM_SRP_ONLY_CAPABLE; |
| break; |
| default: |
| val = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE; |
| break; |
| } |
| dev_dbg(hsotg->dev, "Setting otg_cap to %d\n", val); |
| } |
| |
| hsotg->core_params->otg_cap = val; |
| } |
| |
| void dwc2_set_param_dma_enable(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val > 0 && hsotg->hw_params.arch == GHWCFG2_SLAVE_ONLY_ARCH) |
| valid = 0; |
| if (val < 0) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for dma_enable parameter. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.arch != GHWCFG2_SLAVE_ONLY_ARCH; |
| dev_dbg(hsotg->dev, "Setting dma_enable to %d\n", val); |
| } |
| |
| hsotg->core_params->dma_enable = val; |
| } |
| |
| void dwc2_set_param_dma_desc_enable(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val > 0 && (hsotg->core_params->dma_enable <= 0 || |
| !hsotg->hw_params.dma_desc_enable)) |
| valid = 0; |
| if (val < 0) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for dma_desc_enable parameter. Check HW configuration.\n", |
| val); |
| val = (hsotg->core_params->dma_enable > 0 && |
| hsotg->hw_params.dma_desc_enable); |
| dev_dbg(hsotg->dev, "Setting dma_desc_enable to %d\n", val); |
| } |
| |
| hsotg->core_params->dma_desc_enable = val; |
| } |
| |
| void dwc2_set_param_dma_desc_fs_enable(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val > 0 && (hsotg->core_params->dma_enable <= 0 || |
| !hsotg->hw_params.dma_desc_enable)) |
| valid = 0; |
| if (val < 0) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for dma_desc_fs_enable parameter. Check HW configuration.\n", |
| val); |
| val = (hsotg->core_params->dma_enable > 0 && |
| hsotg->hw_params.dma_desc_enable); |
| } |
| |
| hsotg->core_params->dma_desc_fs_enable = val; |
| dev_dbg(hsotg->dev, "Setting dma_desc_fs_enable to %d\n", val); |
| } |
| |
| void dwc2_set_param_host_support_fs_ls_low_power(struct dwc2_hsotg *hsotg, |
| int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "Wrong value for host_support_fs_low_power\n"); |
| dev_err(hsotg->dev, |
| "host_support_fs_low_power must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, |
| "Setting host_support_fs_low_power to %d\n", val); |
| } |
| |
| hsotg->core_params->host_support_fs_ls_low_power = val; |
| } |
| |
| void dwc2_set_param_enable_dynamic_fifo(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val > 0 && !hsotg->hw_params.enable_dynamic_fifo) |
| valid = 0; |
| if (val < 0) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for enable_dynamic_fifo parameter. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.enable_dynamic_fifo; |
| dev_dbg(hsotg->dev, "Setting enable_dynamic_fifo to %d\n", val); |
| } |
| |
| hsotg->core_params->enable_dynamic_fifo = val; |
| } |
| |
| void dwc2_set_param_host_rx_fifo_size(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 16 || val > hsotg->hw_params.host_rx_fifo_size) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for host_rx_fifo_size. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.host_rx_fifo_size; |
| dev_dbg(hsotg->dev, "Setting host_rx_fifo_size to %d\n", val); |
| } |
| |
| hsotg->core_params->host_rx_fifo_size = val; |
| } |
| |
| void dwc2_set_param_host_nperio_tx_fifo_size(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 16 || val > hsotg->hw_params.host_nperio_tx_fifo_size) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for host_nperio_tx_fifo_size. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.host_nperio_tx_fifo_size; |
| dev_dbg(hsotg->dev, "Setting host_nperio_tx_fifo_size to %d\n", |
| val); |
| } |
| |
| hsotg->core_params->host_nperio_tx_fifo_size = val; |
| } |
| |
| void dwc2_set_param_host_perio_tx_fifo_size(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 16 || val > hsotg->hw_params.host_perio_tx_fifo_size) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for host_perio_tx_fifo_size. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.host_perio_tx_fifo_size; |
| dev_dbg(hsotg->dev, "Setting host_perio_tx_fifo_size to %d\n", |
| val); |
| } |
| |
| hsotg->core_params->host_perio_tx_fifo_size = val; |
| } |
| |
| void dwc2_set_param_max_transfer_size(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 2047 || val > hsotg->hw_params.max_transfer_size) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for max_transfer_size. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.max_transfer_size; |
| dev_dbg(hsotg->dev, "Setting max_transfer_size to %d\n", val); |
| } |
| |
| hsotg->core_params->max_transfer_size = val; |
| } |
| |
| void dwc2_set_param_max_packet_count(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 15 || val > hsotg->hw_params.max_packet_count) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for max_packet_count. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.max_packet_count; |
| dev_dbg(hsotg->dev, "Setting max_packet_count to %d\n", val); |
| } |
| |
| hsotg->core_params->max_packet_count = val; |
| } |
| |
| void dwc2_set_param_host_channels(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (val < 1 || val > hsotg->hw_params.host_channels) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for host_channels. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.host_channels; |
| dev_dbg(hsotg->dev, "Setting host_channels to %d\n", val); |
| } |
| |
| hsotg->core_params->host_channels = val; |
| } |
| |
| void dwc2_set_param_phy_type(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 0; |
| u32 hs_phy_type, fs_phy_type; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, DWC2_PHY_TYPE_PARAM_FS, |
| DWC2_PHY_TYPE_PARAM_ULPI)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for phy_type\n"); |
| dev_err(hsotg->dev, "phy_type must be 0, 1 or 2\n"); |
| } |
| |
| valid = 0; |
| } |
| |
| hs_phy_type = hsotg->hw_params.hs_phy_type; |
| fs_phy_type = hsotg->hw_params.fs_phy_type; |
| if (val == DWC2_PHY_TYPE_PARAM_UTMI && |
| (hs_phy_type == GHWCFG2_HS_PHY_TYPE_UTMI || |
| hs_phy_type == GHWCFG2_HS_PHY_TYPE_UTMI_ULPI)) |
| valid = 1; |
| else if (val == DWC2_PHY_TYPE_PARAM_ULPI && |
| (hs_phy_type == GHWCFG2_HS_PHY_TYPE_ULPI || |
| hs_phy_type == GHWCFG2_HS_PHY_TYPE_UTMI_ULPI)) |
| valid = 1; |
| else if (val == DWC2_PHY_TYPE_PARAM_FS && |
| fs_phy_type == GHWCFG2_FS_PHY_TYPE_DEDICATED) |
| valid = 1; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for phy_type. Check HW configuration.\n", |
| val); |
| val = DWC2_PHY_TYPE_PARAM_FS; |
| if (hs_phy_type != GHWCFG2_HS_PHY_TYPE_NOT_SUPPORTED) { |
| if (hs_phy_type == GHWCFG2_HS_PHY_TYPE_UTMI || |
| hs_phy_type == GHWCFG2_HS_PHY_TYPE_UTMI_ULPI) |
| val = DWC2_PHY_TYPE_PARAM_UTMI; |
| else |
| val = DWC2_PHY_TYPE_PARAM_ULPI; |
| } |
| dev_dbg(hsotg->dev, "Setting phy_type to %d\n", val); |
| } |
| |
| hsotg->core_params->phy_type = val; |
| } |
| |
| static int dwc2_get_param_phy_type(struct dwc2_hsotg *hsotg) |
| { |
| return hsotg->core_params->phy_type; |
| } |
| |
| void dwc2_set_param_speed(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for speed parameter\n"); |
| dev_err(hsotg->dev, "max_speed parameter must be 0 or 1\n"); |
| } |
| valid = 0; |
| } |
| |
| if (val == DWC2_SPEED_PARAM_HIGH && |
| dwc2_get_param_phy_type(hsotg) == DWC2_PHY_TYPE_PARAM_FS) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for speed parameter. Check HW configuration.\n", |
| val); |
| val = dwc2_get_param_phy_type(hsotg) == DWC2_PHY_TYPE_PARAM_FS ? |
| DWC2_SPEED_PARAM_FULL : DWC2_SPEED_PARAM_HIGH; |
| dev_dbg(hsotg->dev, "Setting speed to %d\n", val); |
| } |
| |
| hsotg->core_params->speed = val; |
| } |
| |
| void dwc2_set_param_host_ls_low_power_phy_clk(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ, |
| DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "Wrong value for host_ls_low_power_phy_clk parameter\n"); |
| dev_err(hsotg->dev, |
| "host_ls_low_power_phy_clk must be 0 or 1\n"); |
| } |
| valid = 0; |
| } |
| |
| if (val == DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ && |
| dwc2_get_param_phy_type(hsotg) == DWC2_PHY_TYPE_PARAM_FS) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for host_ls_low_power_phy_clk. Check HW configuration.\n", |
| val); |
| val = dwc2_get_param_phy_type(hsotg) == DWC2_PHY_TYPE_PARAM_FS |
| ? DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ |
| : DWC2_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ; |
| dev_dbg(hsotg->dev, "Setting host_ls_low_power_phy_clk to %d\n", |
| val); |
| } |
| |
| hsotg->core_params->host_ls_low_power_phy_clk = val; |
| } |
| |
| void dwc2_set_param_phy_ulpi_ddr(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for phy_ulpi_ddr\n"); |
| dev_err(hsotg->dev, "phy_upli_ddr must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting phy_upli_ddr to %d\n", val); |
| } |
| |
| hsotg->core_params->phy_ulpi_ddr = val; |
| } |
| |
| void dwc2_set_param_phy_ulpi_ext_vbus(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "Wrong value for phy_ulpi_ext_vbus\n"); |
| dev_err(hsotg->dev, |
| "phy_ulpi_ext_vbus must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting phy_ulpi_ext_vbus to %d\n", val); |
| } |
| |
| hsotg->core_params->phy_ulpi_ext_vbus = val; |
| } |
| |
| void dwc2_set_param_phy_utmi_width(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 0; |
| |
| switch (hsotg->hw_params.utmi_phy_data_width) { |
| case GHWCFG4_UTMI_PHY_DATA_WIDTH_8: |
| valid = (val == 8); |
| break; |
| case GHWCFG4_UTMI_PHY_DATA_WIDTH_16: |
| valid = (val == 16); |
| break; |
| case GHWCFG4_UTMI_PHY_DATA_WIDTH_8_OR_16: |
| valid = (val == 8 || val == 16); |
| break; |
| } |
| |
| if (!valid) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "%d invalid for phy_utmi_width. Check HW configuration.\n", |
| val); |
| } |
| val = (hsotg->hw_params.utmi_phy_data_width == |
| GHWCFG4_UTMI_PHY_DATA_WIDTH_8) ? 8 : 16; |
| dev_dbg(hsotg->dev, "Setting phy_utmi_width to %d\n", val); |
| } |
| |
| hsotg->core_params->phy_utmi_width = val; |
| } |
| |
| void dwc2_set_param_ulpi_fs_ls(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for ulpi_fs_ls\n"); |
| dev_err(hsotg->dev, "ulpi_fs_ls must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting ulpi_fs_ls to %d\n", val); |
| } |
| |
| hsotg->core_params->ulpi_fs_ls = val; |
| } |
| |
| void dwc2_set_param_ts_dline(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for ts_dline\n"); |
| dev_err(hsotg->dev, "ts_dline must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting ts_dline to %d\n", val); |
| } |
| |
| hsotg->core_params->ts_dline = val; |
| } |
| |
| void dwc2_set_param_i2c_enable(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, "Wrong value for i2c_enable\n"); |
| dev_err(hsotg->dev, "i2c_enable must be 0 or 1\n"); |
| } |
| |
| valid = 0; |
| } |
| |
| if (val == 1 && !(hsotg->hw_params.i2c_enable)) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for i2c_enable. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.i2c_enable; |
| dev_dbg(hsotg->dev, "Setting i2c_enable to %d\n", val); |
| } |
| |
| hsotg->core_params->i2c_enable = val; |
| } |
| |
| void dwc2_set_param_en_multiple_tx_fifo(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "Wrong value for en_multiple_tx_fifo,\n"); |
| dev_err(hsotg->dev, |
| "en_multiple_tx_fifo must be 0 or 1\n"); |
| } |
| valid = 0; |
| } |
| |
| if (val == 1 && !hsotg->hw_params.en_multiple_tx_fifo) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for parameter en_multiple_tx_fifo. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.en_multiple_tx_fifo; |
| dev_dbg(hsotg->dev, "Setting en_multiple_tx_fifo to %d\n", val); |
| } |
| |
| hsotg->core_params->en_multiple_tx_fifo = val; |
| } |
| |
| void dwc2_set_param_reload_ctl(struct dwc2_hsotg *hsotg, int val) |
| { |
| int valid = 1; |
| |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "'%d' invalid for parameter reload_ctl\n", val); |
| dev_err(hsotg->dev, "reload_ctl must be 0 or 1\n"); |
| } |
| valid = 0; |
| } |
| |
| if (val == 1 && hsotg->hw_params.snpsid < DWC2_CORE_REV_2_92a) |
| valid = 0; |
| |
| if (!valid) { |
| if (val >= 0) |
| dev_err(hsotg->dev, |
| "%d invalid for parameter reload_ctl. Check HW configuration.\n", |
| val); |
| val = hsotg->hw_params.snpsid >= DWC2_CORE_REV_2_92a; |
| dev_dbg(hsotg->dev, "Setting reload_ctl to %d\n", val); |
| } |
| |
| hsotg->core_params->reload_ctl = val; |
| } |
| |
| void dwc2_set_param_ahbcfg(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (val != -1) |
| hsotg->core_params->ahbcfg = val; |
| else |
| hsotg->core_params->ahbcfg = GAHBCFG_HBSTLEN_INCR4 << |
| GAHBCFG_HBSTLEN_SHIFT; |
| } |
| |
| void dwc2_set_param_otg_ver(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "'%d' invalid for parameter otg_ver\n", val); |
| dev_err(hsotg->dev, |
| "otg_ver must be 0 (for OTG 1.3 support) or 1 (for OTG 2.0 support)\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting otg_ver to %d\n", val); |
| } |
| |
| hsotg->core_params->otg_ver = val; |
| } |
| |
| static void dwc2_set_param_uframe_sched(struct dwc2_hsotg *hsotg, int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "'%d' invalid for parameter uframe_sched\n", |
| val); |
| dev_err(hsotg->dev, "uframe_sched must be 0 or 1\n"); |
| } |
| val = 1; |
| dev_dbg(hsotg->dev, "Setting uframe_sched to %d\n", val); |
| } |
| |
| hsotg->core_params->uframe_sched = val; |
| } |
| |
| static void dwc2_set_param_external_id_pin_ctl(struct dwc2_hsotg *hsotg, |
| int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "'%d' invalid for parameter external_id_pin_ctl\n", |
| val); |
| dev_err(hsotg->dev, "external_id_pin_ctl must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting external_id_pin_ctl to %d\n", val); |
| } |
| |
| hsotg->core_params->external_id_pin_ctl = val; |
| } |
| |
| static void dwc2_set_param_hibernation(struct dwc2_hsotg *hsotg, |
| int val) |
| { |
| if (DWC2_OUT_OF_BOUNDS(val, 0, 1)) { |
| if (val >= 0) { |
| dev_err(hsotg->dev, |
| "'%d' invalid for parameter hibernation\n", |
| val); |
| dev_err(hsotg->dev, "hibernation must be 0 or 1\n"); |
| } |
| val = 0; |
| dev_dbg(hsotg->dev, "Setting hibernation to %d\n", val); |
| } |
| |
| hsotg->core_params->hibernation = val; |
| } |
| |
| /* |
| * This function is called during module intialization to pass module parameters |
| * for the DWC_otg core. |
| */ |
| void dwc2_set_parameters(struct dwc2_hsotg *hsotg, |
| const struct dwc2_core_params *params) |
| { |
| dev_dbg(hsotg->dev, "%s()\n", __func__); |
| |
| dwc2_set_param_otg_cap(hsotg, params->otg_cap); |
| dwc2_set_param_dma_enable(hsotg, params->dma_enable); |
| dwc2_set_param_dma_desc_enable(hsotg, params->dma_desc_enable); |
| dwc2_set_param_dma_desc_fs_enable(hsotg, params->dma_desc_fs_enable); |
| dwc2_set_param_host_support_fs_ls_low_power(hsotg, |
| params->host_support_fs_ls_low_power); |
| dwc2_set_param_enable_dynamic_fifo(hsotg, |
| params->enable_dynamic_fifo); |
| dwc2_set_param_host_rx_fifo_size(hsotg, |
| params->host_rx_fifo_size); |
| dwc2_set_param_host_nperio_tx_fifo_size(hsotg, |
| params->host_nperio_tx_fifo_size); |
| dwc2_set_param_host_perio_tx_fifo_size(hsotg, |
| params->host_perio_tx_fifo_size); |
| dwc2_set_param_max_transfer_size(hsotg, |
| params->max_transfer_size); |
| dwc2_set_param_max_packet_count(hsotg, |
| params->max_packet_count); |
| dwc2_set_param_host_channels(hsotg, params->host_channels); |
| dwc2_set_param_phy_type(hsotg, params->phy_type); |
| dwc2_set_param_speed(hsotg, params->speed); |
| dwc2_set_param_host_ls_low_power_phy_clk(hsotg, |
| params->host_ls_low_power_phy_clk); |
| dwc2_set_param_phy_ulpi_ddr(hsotg, params->phy_ulpi_ddr); |
| dwc2_set_param_phy_ulpi_ext_vbus(hsotg, |
| params->phy_ulpi_ext_vbus); |
| dwc2_set_param_phy_utmi_width(hsotg, params->phy_utmi_width); |
| dwc2_set_param_ulpi_fs_ls(hsotg, params->ulpi_fs_ls); |
| dwc2_set_param_ts_dline(hsotg, params->ts_dline); |
| dwc2_set_param_i2c_enable(hsotg, params->i2c_enable); |
| dwc2_set_param_en_multiple_tx_fifo(hsotg, |
| params->en_multiple_tx_fifo); |
| dwc2_set_param_reload_ctl(hsotg, params->reload_ctl); |
| dwc2_set_param_ahbcfg(hsotg, params->ahbcfg); |
| dwc2_set_param_otg_ver(hsotg, params->otg_ver); |
| dwc2_set_param_uframe_sched(hsotg, params->uframe_sched); |
| dwc2_set_param_external_id_pin_ctl(hsotg, params->external_id_pin_ctl); |
| dwc2_set_param_hibernation(hsotg, params->hibernation); |
| } |
| |
| /* |
| * Forces either host or device mode if the controller is not |
| * currently in that mode. |
| * |
| * Returns true if the mode was forced. |
| */ |
| static bool dwc2_force_mode_if_needed(struct dwc2_hsotg *hsotg, bool host) |
| { |
| if (host && dwc2_is_host_mode(hsotg)) |
| return false; |
| else if (!host && dwc2_is_device_mode(hsotg)) |
| return false; |
| |
| return dwc2_force_mode(hsotg, host); |
| } |
| |
| /* |
| * Gets host hardware parameters. Forces host mode if not currently in |
| * host mode. Should be called immediately after a core soft reset in |
| * order to get the reset values. |
| */ |
| static void dwc2_get_host_hwparams(struct dwc2_hsotg *hsotg) |
| { |
| struct dwc2_hw_params *hw = &hsotg->hw_params; |
| u32 gnptxfsiz; |
| u32 hptxfsiz; |
| bool forced; |
| |
| if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL) |
| return; |
| |
| forced = dwc2_force_mode_if_needed(hsotg, true); |
| |
| gnptxfsiz = dwc2_readl(hsotg->regs + GNPTXFSIZ); |
| hptxfsiz = dwc2_readl(hsotg->regs + HPTXFSIZ); |
| dev_dbg(hsotg->dev, "gnptxfsiz=%08x\n", gnptxfsiz); |
| dev_dbg(hsotg->dev, "hptxfsiz=%08x\n", hptxfsiz); |
| |
| if (forced) |
| dwc2_clear_force_mode(hsotg); |
| |
| hw->host_nperio_tx_fifo_size = (gnptxfsiz & FIFOSIZE_DEPTH_MASK) >> |
| FIFOSIZE_DEPTH_SHIFT; |
| hw->host_perio_tx_fifo_size = (hptxfsiz & FIFOSIZE_DEPTH_MASK) >> |
| FIFOSIZE_DEPTH_SHIFT; |
| } |
| |
| /* |
| * Gets device hardware parameters. Forces device mode if not |
| * currently in device mode. Should be called immediately after a core |
| * soft reset in order to get the reset values. |
| */ |
| static void dwc2_get_dev_hwparams(struct dwc2_hsotg *hsotg) |
| { |
| struct dwc2_hw_params *hw = &hsotg->hw_params; |
| bool forced; |
| u32 gnptxfsiz; |
| |
| if (hsotg->dr_mode == USB_DR_MODE_HOST) |
| return; |
| |
| forced = dwc2_force_mode_if_needed(hsotg, false); |
| |
| gnptxfsiz = dwc2_readl(hsotg->regs + GNPTXFSIZ); |
| dev_dbg(hsotg->dev, "gnptxfsiz=%08x\n", gnptxfsiz); |
| |
| if (forced) |
| dwc2_clear_force_mode(hsotg); |
| |
| hw->dev_nperio_tx_fifo_size = (gnptxfsiz & FIFOSIZE_DEPTH_MASK) >> |
| FIFOSIZE_DEPTH_SHIFT; |
| } |
| |
| /** |
| * During device initialization, read various hardware configuration |
| * registers and interpret the contents. |
| */ |
| int dwc2_get_hwparams(struct dwc2_hsotg *hsotg) |
| { |
| struct dwc2_hw_params *hw = &hsotg->hw_params; |
| unsigned width; |
| u32 hwcfg1, hwcfg2, hwcfg3, hwcfg4; |
| u32 grxfsiz; |
| |
| /* |
| * Attempt to ensure this device is really a DWC_otg Controller. |
| * Read and verify the GSNPSID register contents. The value should be |
| * 0x45f42xxx or 0x45f43xxx, which corresponds to either "OT2" or "OT3", |
| * as in "OTG version 2.xx" or "OTG version 3.xx". |
| */ |
| hw->snpsid = dwc2_readl(hsotg->regs + GSNPSID); |
| if ((hw->snpsid & 0xfffff000) != 0x4f542000 && |
| (hw->snpsid & 0xfffff000) != 0x4f543000) { |
| dev_err(hsotg->dev, "Bad value for GSNPSID: 0x%08x\n", |
| hw->snpsid); |
| return -ENODEV; |
| } |
| |
| dev_dbg(hsotg->dev, "Core Release: %1x.%1x%1x%1x (snpsid=%x)\n", |
| hw->snpsid >> 12 & 0xf, hw->snpsid >> 8 & 0xf, |
| hw->snpsid >> 4 & 0xf, hw->snpsid & 0xf, hw->snpsid); |
| |
| hwcfg1 = dwc2_readl(hsotg->regs + GHWCFG1); |
| hwcfg2 = dwc2_readl(hsotg->regs + GHWCFG2); |
| hwcfg3 = dwc2_readl(hsotg->regs + GHWCFG3); |
| hwcfg4 = dwc2_readl(hsotg->regs + GHWCFG4); |
| grxfsiz = dwc2_readl(hsotg->regs + GRXFSIZ); |
| |
| dev_dbg(hsotg->dev, "hwcfg1=%08x\n", hwcfg1); |
| dev_dbg(hsotg->dev, "hwcfg2=%08x\n", hwcfg2); |
| dev_dbg(hsotg->dev, "hwcfg3=%08x\n", hwcfg3); |
| dev_dbg(hsotg->dev, "hwcfg4=%08x\n", hwcfg4); |
| dev_dbg(hsotg->dev, "grxfsiz=%08x\n", grxfsiz); |
| |
| /* |
| * Host specific hardware parameters. Reading these parameters |
| * requires the controller to be in host mode. The mode will |
| * be forced, if necessary, to read these values. |
| */ |
| dwc2_get_host_hwparams(hsotg); |
| dwc2_get_dev_hwparams(hsotg); |
| |
| /* hwcfg1 */ |
| hw->dev_ep_dirs = hwcfg1; |
| |
| /* hwcfg2 */ |
| hw->op_mode = (hwcfg2 & GHWCFG2_OP_MODE_MASK) >> |
| GHWCFG2_OP_MODE_SHIFT; |
| hw->arch = (hwcfg2 & GHWCFG2_ARCHITECTURE_MASK) >> |
| GHWCFG2_ARCHITECTURE_SHIFT; |
| hw->enable_dynamic_fifo = !!(hwcfg2 & GHWCFG2_DYNAMIC_FIFO); |
| hw->host_channels = 1 + ((hwcfg2 & GHWCFG2_NUM_HOST_CHAN_MASK) >> |
| GHWCFG2_NUM_HOST_CHAN_SHIFT); |
| hw->hs_phy_type = (hwcfg2 & GHWCFG2_HS_PHY_TYPE_MASK) >> |
| GHWCFG2_HS_PHY_TYPE_SHIFT; |
| hw->fs_phy_type = (hwcfg2 & GHWCFG2_FS_PHY_TYPE_MASK) >> |
| GHWCFG2_FS_PHY_TYPE_SHIFT; |
| hw->num_dev_ep = (hwcfg2 & GHWCFG2_NUM_DEV_EP_MASK) >> |
| GHWCFG2_NUM_DEV_EP_SHIFT; |
| hw->nperio_tx_q_depth = |
| (hwcfg2 & GHWCFG2_NONPERIO_TX_Q_DEPTH_MASK) >> |
| GHWCFG2_NONPERIO_TX_Q_DEPTH_SHIFT << 1; |
| hw->host_perio_tx_q_depth = |
| (hwcfg2 & GHWCFG2_HOST_PERIO_TX_Q_DEPTH_MASK) >> |
| GHWCFG2_HOST_PERIO_TX_Q_DEPTH_SHIFT << 1; |
| hw->dev_token_q_depth = |
| (hwcfg2 & GHWCFG2_DEV_TOKEN_Q_DEPTH_MASK) >> |
| GHWCFG2_DEV_TOKEN_Q_DEPTH_SHIFT; |
| |
| /* hwcfg3 */ |
| width = (hwcfg3 & GHWCFG3_XFER_SIZE_CNTR_WIDTH_MASK) >> |
| GHWCFG3_XFER_SIZE_CNTR_WIDTH_SHIFT; |
| hw->max_transfer_size = (1 << (width + 11)) - 1; |
| width = (hwcfg3 & GHWCFG3_PACKET_SIZE_CNTR_WIDTH_MASK) >> |
| GHWCFG3_PACKET_SIZE_CNTR_WIDTH_SHIFT; |
| hw->max_packet_count = (1 << (width + 4)) - 1; |
| hw->i2c_enable = !!(hwcfg3 & GHWCFG3_I2C); |
| hw->total_fifo_size = (hwcfg3 & GHWCFG3_DFIFO_DEPTH_MASK) >> |
| GHWCFG3_DFIFO_DEPTH_SHIFT; |
| |
| /* hwcfg4 */ |
| hw->en_multiple_tx_fifo = !!(hwcfg4 & GHWCFG4_DED_FIFO_EN); |
| hw->num_dev_perio_in_ep = (hwcfg4 & GHWCFG4_NUM_DEV_PERIO_IN_EP_MASK) >> |
| GHWCFG4_NUM_DEV_PERIO_IN_EP_SHIFT; |
| hw->dma_desc_enable = !!(hwcfg4 & GHWCFG4_DESC_DMA); |
| hw->power_optimized = !!(hwcfg4 & GHWCFG4_POWER_OPTIMIZ); |
| hw->utmi_phy_data_width = (hwcfg4 & GHWCFG4_UTMI_PHY_DATA_WIDTH_MASK) >> |
| GHWCFG4_UTMI_PHY_DATA_WIDTH_SHIFT; |
| |
| /* fifo sizes */ |
| hw->host_rx_fifo_size = (grxfsiz & GRXFSIZ_DEPTH_MASK) >> |
| GRXFSIZ_DEPTH_SHIFT; |
| |
| dev_dbg(hsotg->dev, "Detected values from hardware:\n"); |
| dev_dbg(hsotg->dev, " op_mode=%d\n", |
| hw->op_mode); |
| dev_dbg(hsotg->dev, " arch=%d\n", |
| hw->arch); |
| dev_dbg(hsotg->dev, " dma_desc_enable=%d\n", |
| hw->dma_desc_enable); |
| dev_dbg(hsotg->dev, " power_optimized=%d\n", |
| hw->power_optimized); |
| dev_dbg(hsotg->dev, " i2c_enable=%d\n", |
| hw->i2c_enable); |
| dev_dbg(hsotg->dev, " hs_phy_type=%d\n", |
| hw->hs_phy_type); |
| dev_dbg(hsotg->dev, " fs_phy_type=%d\n", |
| hw->fs_phy_type); |
| dev_dbg(hsotg->dev, " utmi_phy_data_width=%d\n", |
| hw->utmi_phy_data_width); |
| dev_dbg(hsotg->dev, " num_dev_ep=%d\n", |
| hw->num_dev_ep); |
| dev_dbg(hsotg->dev, " num_dev_perio_in_ep=%d\n", |
| hw->num_dev_perio_in_ep); |
| dev_dbg(hsotg->dev, " host_channels=%d\n", |
| hw->host_channels); |
| dev_dbg(hsotg->dev, " max_transfer_size=%d\n", |
| hw->max_transfer_size); |
| dev_dbg(hsotg->dev, " max_packet_count=%d\n", |
| hw->max_packet_count); |
| dev_dbg(hsotg->dev, " nperio_tx_q_depth=0x%0x\n", |
| hw->nperio_tx_q_depth); |
| dev_dbg(hsotg->dev, " host_perio_tx_q_depth=0x%0x\n", |
| hw->host_perio_tx_q_depth); |
| dev_dbg(hsotg->dev, " dev_token_q_depth=0x%0x\n", |
| hw->dev_token_q_depth); |
| dev_dbg(hsotg->dev, " enable_dynamic_fifo=%d\n", |
| hw->enable_dynamic_fifo); |
| dev_dbg(hsotg->dev, " en_multiple_tx_fifo=%d\n", |
| hw->en_multiple_tx_fifo); |
| dev_dbg(hsotg->dev, " total_fifo_size=%d\n", |
| hw->total_fifo_size); |
| dev_dbg(hsotg->dev, " host_rx_fifo_size=%d\n", |
| hw->host_rx_fifo_size); |
| dev_dbg(hsotg->dev, " host_nperio_tx_fifo_size=%d\n", |
| hw->host_nperio_tx_fifo_size); |
| dev_dbg(hsotg->dev, " host_perio_tx_fifo_size=%d\n", |
| hw->host_perio_tx_fifo_size); |
| dev_dbg(hsotg->dev, "\n"); |
| |
| return 0; |
| } |
| |
| /* |
| * Sets all parameters to the given value. |
| * |
| * Assumes that the dwc2_core_params struct contains only integers. |
| */ |
| void dwc2_set_all_params(struct dwc2_core_params *params, int value) |
| { |
| int *p = (int *)params; |
| size_t size = sizeof(*params) / sizeof(*p); |
| int i; |
| |
| for (i = 0; i < size; i++) |
| p[i] = value; |
| } |
| |
| |
| u16 dwc2_get_otg_version(struct dwc2_hsotg *hsotg) |
| { |
| return hsotg->core_params->otg_ver == 1 ? 0x0200 : 0x0103; |
| } |
| |
| bool dwc2_is_controller_alive(struct dwc2_hsotg *hsotg) |
| { |
| if (dwc2_readl(hsotg->regs + GSNPSID) == 0xffffffff) |
| return false; |
| else |
| return true; |
| } |
| |
| /** |
| * dwc2_enable_global_interrupts() - Enables the controller's Global |
| * Interrupt in the AHB Config register |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| */ |
| void dwc2_enable_global_interrupts(struct dwc2_hsotg *hsotg) |
| { |
| u32 ahbcfg = dwc2_readl(hsotg->regs + GAHBCFG); |
| |
| ahbcfg |= GAHBCFG_GLBL_INTR_EN; |
| dwc2_writel(ahbcfg, hsotg->regs + GAHBCFG); |
| } |
| |
| /** |
| * dwc2_disable_global_interrupts() - Disables the controller's Global |
| * Interrupt in the AHB Config register |
| * |
| * @hsotg: Programming view of DWC_otg controller |
| */ |
| void dwc2_disable_global_interrupts(struct dwc2_hsotg *hsotg) |
| { |
| u32 ahbcfg = dwc2_readl(hsotg->regs + GAHBCFG); |
| |
| ahbcfg &= ~GAHBCFG_GLBL_INTR_EN; |
| dwc2_writel(ahbcfg, hsotg->regs + GAHBCFG); |
| } |
| |
| /* Returns the controller's GHWCFG2.OTG_MODE. */ |
| unsigned dwc2_op_mode(struct dwc2_hsotg *hsotg) |
| { |
| u32 ghwcfg2 = dwc2_readl(hsotg->regs + GHWCFG2); |
| |
| return (ghwcfg2 & GHWCFG2_OP_MODE_MASK) >> |
| GHWCFG2_OP_MODE_SHIFT; |
| } |
| |
| /* Returns true if the controller is capable of DRD. */ |
| bool dwc2_hw_is_otg(struct dwc2_hsotg *hsotg) |
| { |
| unsigned op_mode = dwc2_op_mode(hsotg); |
| |
| return (op_mode == GHWCFG2_OP_MODE_HNP_SRP_CAPABLE) || |
| (op_mode == GHWCFG2_OP_MODE_SRP_ONLY_CAPABLE) || |
| (op_mode == GHWCFG2_OP_MODE_NO_HNP_SRP_CAPABLE); |
| } |
| |
| /* Returns true if the controller is host-only. */ |
| bool dwc2_hw_is_host(struct dwc2_hsotg *hsotg) |
| { |
| unsigned op_mode = dwc2_op_mode(hsotg); |
| |
| return (op_mode == GHWCFG2_OP_MODE_SRP_CAPABLE_HOST) || |
| (op_mode == GHWCFG2_OP_MODE_NO_SRP_CAPABLE_HOST); |
| } |
| |
| /* Returns true if the controller is device-only. */ |
| bool dwc2_hw_is_device(struct dwc2_hsotg *hsotg) |
| { |
| unsigned op_mode = dwc2_op_mode(hsotg); |
| |
| return (op_mode == GHWCFG2_OP_MODE_SRP_CAPABLE_DEVICE) || |
| (op_mode == GHWCFG2_OP_MODE_NO_SRP_CAPABLE_DEVICE); |
| } |
| |
| MODULE_DESCRIPTION("DESIGNWARE HS OTG Core"); |
| MODULE_AUTHOR("Synopsys, Inc."); |
| MODULE_LICENSE("Dual BSD/GPL"); |