| menuconfig OMAP2_DSS |
| tristate "OMAP2/3 Display Subsystem support (EXPERIMENTAL)" |
| depends on ARCH_OMAP2 || ARCH_OMAP3 |
| help |
| OMAP2/3 Display Subsystem support. |
| |
| if OMAP2_DSS |
| |
| config OMAP2_VRAM_SIZE |
| int "VRAM size (MB)" |
| range 0 32 |
| default 0 |
| help |
| The amount of SDRAM to reserve at boot time for video RAM use. |
| This VRAM will be used by omapfb and other drivers that need |
| large continuous RAM area for video use. |
| |
| You can also set this with "vram=<bytes>" kernel argument, or |
| in the board file. |
| |
| config OMAP2_DSS_DEBUG_SUPPORT |
| bool "Debug support" |
| default y |
| help |
| This enables debug messages. You need to enable printing |
| with 'debug' module parameter. |
| |
| config OMAP2_DSS_COLLECT_IRQ_STATS |
| bool "Collect DSS IRQ statistics" |
| depends on OMAP2_DSS_DEBUG_SUPPORT |
| default n |
| help |
| Collect DSS IRQ statistics, printable via debugfs |
| |
| config OMAP2_DSS_RFBI |
| bool "RFBI support" |
| default n |
| help |
| MIPI DBI, or RFBI (Remote Framebuffer Interface), support. |
| |
| config OMAP2_DSS_VENC |
| bool "VENC support" |
| default y |
| help |
| OMAP Video Encoder support. |
| |
| config OMAP2_DSS_SDI |
| bool "SDI support" |
| depends on ARCH_OMAP3 |
| default n |
| help |
| SDI (Serial Display Interface) support. |
| |
| config OMAP2_DSS_DSI |
| bool "DSI support" |
| depends on ARCH_OMAP3 |
| default n |
| help |
| MIPI DSI support. |
| |
| config OMAP2_DSS_USE_DSI_PLL |
| bool "Use DSI PLL for PCLK (EXPERIMENTAL)" |
| default n |
| depends on OMAP2_DSS_DSI |
| help |
| Use DSI PLL to generate pixel clock. Currently only for DPI output. |
| DSI PLL can be used to generate higher and more precise pixel clocks. |
| |
| config OMAP2_DSS_FAKE_VSYNC |
| bool "Fake VSYNC irq from manual update displays" |
| default n |
| help |
| If this is selected, DSI will generate a fake DISPC VSYNC interrupt |
| when DSI has sent a frame. This is only needed with DSI or RFBI |
| displays using manual mode, and you want VSYNC to, for example, |
| time animation. |
| |
| config OMAP2_DSS_MIN_FCK_PER_PCK |
| int "Minimum FCK/PCK ratio (for scaling)" |
| range 0 32 |
| default 0 |
| help |
| This can be used to adjust the minimum FCK/PCK ratio. |
| |
| With this you can make sure that DISPC FCK is at least |
| n x PCK. Video plane scaling requires higher FCK than |
| normally. |
| |
| If this is set to 0, there's no extra constraint on the |
| DISPC FCK. However, the FCK will at minimum be |
| 2xPCK (if active matrix) or 3xPCK (if passive matrix). |
| |
| Max FCK is 173MHz, so this doesn't work if your PCK |
| is very high. |
| |
| endif |