| /* |
| * Device Tree Source for AM4372 SoC |
| * |
| * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| / { |
| compatible = "ti,am4372", "ti,am43"; |
| interrupt-parent = <&wakeupgen>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| chosen { }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0 0>; |
| }; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| serial3 = &uart3; |
| serial4 = &uart4; |
| serial5 = &uart5; |
| ethernet0 = &cpsw_emac0; |
| ethernet1 = &cpsw_emac1; |
| spi0 = &qspi; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| cpu: cpu@0 { |
| compatible = "arm,cortex-a9"; |
| device_type = "cpu"; |
| reg = <0>; |
| |
| clocks = <&dpll_mpu_ck>; |
| clock-names = "cpu"; |
| |
| operating-points-v2 = <&cpu0_opp_table>; |
| ti,syscon-efuse = <&scm_conf 0x610 0x3f 0>; |
| ti,syscon-rev = <&scm_conf 0x600>; |
| |
| clock-latency = <300000>; /* From omap-cpufreq driver */ |
| }; |
| }; |
| |
| cpu0_opp_table: opp_table0 { |
| compatible = "operating-points-v2"; |
| |
| opp50@300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-microvolt = <950000 931000 969000>; |
| opp-supported-hw = <0xFF 0x01>; |
| opp-suspend; |
| }; |
| |
| opp100@600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <1100000 1078000 1122000>; |
| opp-supported-hw = <0xFF 0x04>; |
| }; |
| |
| opp120@720000000 { |
| opp-hz = /bits/ 64 <720000000>; |
| opp-microvolt = <1200000 1176000 1224000>; |
| opp-supported-hw = <0xFF 0x08>; |
| }; |
| |
| oppturbo@800000000 { |
| opp-hz = /bits/ 64 <800000000>; |
| opp-microvolt = <1260000 1234800 1285200>; |
| opp-supported-hw = <0xFF 0x10>; |
| }; |
| |
| oppnitro@1000000000 { |
| opp-hz = /bits/ 64 <1000000000>; |
| opp-microvolt = <1325000 1298500 1351500>; |
| opp-supported-hw = <0xFF 0x20>; |
| }; |
| }; |
| |
| gic: interrupt-controller@48241000 { |
| compatible = "arm,cortex-a9-gic"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x48241000 0x1000>, |
| <0x48240100 0x0100>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| wakeupgen: interrupt-controller@48281000 { |
| compatible = "ti,omap4-wugen-mpu"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x48281000 0x1000>; |
| interrupt-parent = <&gic>; |
| }; |
| |
| scu: scu@48240000 { |
| compatible = "arm,cortex-a9-scu"; |
| reg = <0x48240000 0x100>; |
| }; |
| |
| global_timer: timer@48240200 { |
| compatible = "arm,cortex-a9-global-timer"; |
| reg = <0x48240200 0x100>; |
| interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>; |
| interrupt-parent = <&gic>; |
| clocks = <&mpu_periphclk>; |
| }; |
| |
| local_timer: timer@48240600 { |
| compatible = "arm,cortex-a9-twd-timer"; |
| reg = <0x48240600 0x100>; |
| interrupts = <GIC_PPI 13 IRQ_TYPE_EDGE_RISING>; |
| interrupt-parent = <&gic>; |
| clocks = <&mpu_periphclk>; |
| }; |
| |
| l2-cache-controller@48242000 { |
| compatible = "arm,pl310-cache"; |
| reg = <0x48242000 0x1000>; |
| cache-unified; |
| cache-level = <2>; |
| }; |
| |
| ocp@44000000 { |
| compatible = "ti,am4372-l3-noc", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "l3_main"; |
| reg = <0x44000000 0x400000 |
| 0x44800000 0x400000>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| |
| l4_wkup: l4_wkup@44c00000 { |
| compatible = "ti,am4-l4-wkup", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x44c00000 0x287000>; |
| |
| wkup_m3: wkup_m3@100000 { |
| compatible = "ti,am4372-wkup-m3"; |
| reg = <0x100000 0x4000>, |
| <0x180000 0x2000>; |
| reg-names = "umem", "dmem"; |
| ti,hwmods = "wkup_m3"; |
| ti,pm-firmware = "am335x-pm-firmware.elf"; |
| }; |
| |
| prcm: prcm@1f0000 { |
| compatible = "ti,am4-prcm"; |
| reg = <0x1f0000 0x11000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| |
| prcm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| prcm_clockdomains: clockdomains { |
| }; |
| }; |
| |
| scm: scm@210000 { |
| compatible = "ti,am4-scm", "simple-bus"; |
| reg = <0x210000 0x4000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x210000 0x4000>; |
| |
| am43xx_pinmux: pinmux@800 { |
| compatible = "ti,am437-padconf", |
| "pinctrl-single"; |
| reg = <0x800 0x31c>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #pinctrl-cells = <1>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <32>; |
| pinctrl-single,function-mask = <0xffffffff>; |
| }; |
| |
| scm_conf: scm_conf@0 { |
| compatible = "syscon"; |
| reg = <0x0 0x800>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| scm_clocks: clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| wkup_m3_ipc: wkup_m3_ipc@1324 { |
| compatible = "ti,am4372-wkup-m3-ipc"; |
| reg = <0x1324 0x44>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| ti,rproc = <&wkup_m3>; |
| mboxes = <&mailbox &mbox_wkupm3>; |
| }; |
| |
| edma_xbar: dma-router@f90 { |
| compatible = "ti,am335x-edma-crossbar"; |
| reg = <0xf90 0x40>; |
| #dma-cells = <3>; |
| dma-requests = <64>; |
| dma-masters = <&edma>; |
| }; |
| |
| scm_clockdomains: clockdomains { |
| }; |
| }; |
| }; |
| |
| emif: emif@4c000000 { |
| compatible = "ti,emif-am4372"; |
| reg = <0x4c000000 0x1000000>; |
| ti,hwmods = "emif"; |
| }; |
| |
| edma: edma@49000000 { |
| compatible = "ti,edma3-tpcc"; |
| ti,hwmods = "tpcc"; |
| reg = <0x49000000 0x10000>; |
| reg-names = "edma3_cc"; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "edma3_ccint", "edma3_mperr", |
| "edma3_ccerrint"; |
| dma-requests = <64>; |
| #dma-cells = <2>; |
| |
| ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>, |
| <&edma_tptc2 0>; |
| |
| ti,edma-memcpy-channels = <58 59>; |
| }; |
| |
| edma_tptc0: tptc@49800000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc0"; |
| reg = <0x49800000 0x100000>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| edma_tptc1: tptc@49900000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc1"; |
| reg = <0x49900000 0x100000>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| edma_tptc2: tptc@49a00000 { |
| compatible = "ti,edma3-tptc"; |
| ti,hwmods = "tptc2"; |
| reg = <0x49a00000 0x100000>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "edma3_tcerrint"; |
| }; |
| |
| uart0: serial@44e09000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x44e09000 0x2000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart1"; |
| }; |
| |
| uart1: serial@48022000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x48022000 0x2000>; |
| interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart2"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@48024000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x48024000 0x2000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart3"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@481a6000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x481a6000 0x2000>; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart4"; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@481a8000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x481a8000 0x2000>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart5"; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@481aa000 { |
| compatible = "ti,am4372-uart","ti,omap2-uart"; |
| reg = <0x481aa000 0x2000>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "uart6"; |
| status = "disabled"; |
| }; |
| |
| mailbox: mailbox@480C8000 { |
| compatible = "ti,omap4-mailbox"; |
| reg = <0x480C8000 0x200>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "mailbox"; |
| #mbox-cells = <1>; |
| ti,mbox-num-users = <4>; |
| ti,mbox-num-fifos = <8>; |
| mbox_wkupm3: wkup_m3 { |
| ti,mbox-send-noirq; |
| ti,mbox-tx = <0 0 0>; |
| ti,mbox-rx = <0 0 3>; |
| }; |
| }; |
| |
| timer1: timer@44e31000 { |
| compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms"; |
| reg = <0x44e31000 0x400>; |
| interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| ti,timer-alwon; |
| ti,hwmods = "timer1"; |
| }; |
| |
| timer2: timer@48040000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48040000 0x400>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer2"; |
| }; |
| |
| timer3: timer@48042000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48042000 0x400>; |
| interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer3"; |
| status = "disabled"; |
| }; |
| |
| timer4: timer@48044000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48044000 0x400>; |
| interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; |
| ti,timer-pwm; |
| ti,hwmods = "timer4"; |
| status = "disabled"; |
| }; |
| |
| timer5: timer@48046000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48046000 0x400>; |
| interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; |
| ti,timer-pwm; |
| ti,hwmods = "timer5"; |
| status = "disabled"; |
| }; |
| |
| timer6: timer@48048000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48048000 0x400>; |
| interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; |
| ti,timer-pwm; |
| ti,hwmods = "timer6"; |
| status = "disabled"; |
| }; |
| |
| timer7: timer@4804a000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x4804a000 0x400>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| ti,timer-pwm; |
| ti,hwmods = "timer7"; |
| status = "disabled"; |
| }; |
| |
| timer8: timer@481c1000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x481c1000 0x400>; |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer8"; |
| status = "disabled"; |
| }; |
| |
| timer9: timer@4833d000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x4833d000 0x400>; |
| interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer9"; |
| status = "disabled"; |
| }; |
| |
| timer10: timer@4833f000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x4833f000 0x400>; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer10"; |
| status = "disabled"; |
| }; |
| |
| timer11: timer@48341000 { |
| compatible = "ti,am4372-timer","ti,am335x-timer"; |
| reg = <0x48341000 0x400>; |
| interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "timer11"; |
| status = "disabled"; |
| }; |
| |
| counter32k: counter@44e86000 { |
| compatible = "ti,am4372-counter32k","ti,omap-counter32k"; |
| reg = <0x44e86000 0x40>; |
| ti,hwmods = "counter_32k"; |
| }; |
| |
| rtc: rtc@44e3e000 { |
| compatible = "ti,am4372-rtc", "ti,am3352-rtc", |
| "ti,da830-rtc"; |
| reg = <0x44e3e000 0x1000>; |
| interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH |
| GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "rtc"; |
| clocks = <&clk_32768_ck>; |
| clock-names = "int-clk"; |
| status = "disabled"; |
| }; |
| |
| wdt: wdt@44e35000 { |
| compatible = "ti,am4372-wdt","ti,omap3-wdt"; |
| reg = <0x44e35000 0x1000>; |
| interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "wd_timer2"; |
| }; |
| |
| gpio0: gpio@44e07000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x44e07000 0x1000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio1"; |
| status = "disabled"; |
| }; |
| |
| gpio1: gpio@4804c000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x4804c000 0x1000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio2"; |
| status = "disabled"; |
| }; |
| |
| gpio2: gpio@481ac000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x481ac000 0x1000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio3"; |
| status = "disabled"; |
| }; |
| |
| gpio3: gpio@481ae000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x481ae000 0x1000>; |
| interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio4"; |
| status = "disabled"; |
| }; |
| |
| gpio4: gpio@48320000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x48320000 0x1000>; |
| interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio5"; |
| status = "disabled"; |
| }; |
| |
| gpio5: gpio@48322000 { |
| compatible = "ti,am4372-gpio","ti,omap4-gpio"; |
| reg = <0x48322000 0x1000>; |
| interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| ti,hwmods = "gpio6"; |
| status = "disabled"; |
| }; |
| |
| hwspinlock: spinlock@480ca000 { |
| compatible = "ti,omap4-hwspinlock"; |
| reg = <0x480ca000 0x1000>; |
| ti,hwmods = "spinlock"; |
| #hwlock-cells = <1>; |
| }; |
| |
| i2c0: i2c@44e0b000 { |
| compatible = "ti,am4372-i2c","ti,omap4-i2c"; |
| reg = <0x44e0b000 0x1000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "i2c1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@4802a000 { |
| compatible = "ti,am4372-i2c","ti,omap4-i2c"; |
| reg = <0x4802a000 0x1000>; |
| interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "i2c2"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@4819c000 { |
| compatible = "ti,am4372-i2c","ti,omap4-i2c"; |
| reg = <0x4819c000 0x1000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "i2c3"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@48030000 { |
| compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; |
| reg = <0x48030000 0x400>; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "spi0"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| mmc1: mmc@48060000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x48060000 0x1000>; |
| ti,hwmods = "mmc1"; |
| ti,dual-volt; |
| ti,needs-special-reset; |
| dmas = <&edma 24 0>, |
| <&edma 25 0>; |
| dma-names = "tx", "rx"; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| mmc2: mmc@481d8000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x481d8000 0x1000>; |
| ti,hwmods = "mmc2"; |
| ti,needs-special-reset; |
| dmas = <&edma 2 0>, |
| <&edma 3 0>; |
| dma-names = "tx", "rx"; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| mmc3: mmc@47810000 { |
| compatible = "ti,omap4-hsmmc"; |
| reg = <0x47810000 0x1000>; |
| ti,hwmods = "mmc3"; |
| ti,needs-special-reset; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@481a0000 { |
| compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; |
| reg = <0x481a0000 0x400>; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "spi1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi2: spi@481a2000 { |
| compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; |
| reg = <0x481a2000 0x400>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "spi2"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@481a4000 { |
| compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; |
| reg = <0x481a4000 0x400>; |
| interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "spi3"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@48345000 { |
| compatible = "ti,am4372-mcspi","ti,omap4-mcspi"; |
| reg = <0x48345000 0x400>; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "spi4"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| mac: ethernet@4a100000 { |
| compatible = "ti,am4372-cpsw","ti,cpsw"; |
| reg = <0x4a100000 0x800 |
| 0x4a101200 0x100>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH |
| GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH |
| GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH |
| GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ti,hwmods = "cpgmac0"; |
| clocks = <&cpsw_125mhz_gclk>, <&cpsw_cpts_rft_clk>, |
| <&dpll_clksel_mac_clk>; |
| clock-names = "fck", "cpts", "50mclk"; |
| assigned-clocks = <&dpll_clksel_mac_clk>; |
| assigned-clock-rates = <50000000>; |
| status = "disabled"; |
| cpdma_channels = <8>; |
| ale_entries = <1024>; |
| bd_ram_size = <0x2000>; |
| mac_control = <0x20>; |
| slaves = <2>; |
| active_slave = <0>; |
| cpts_clock_mult = <0x80000000>; |
| cpts_clock_shift = <29>; |
| ranges; |
| syscon = <&scm_conf>; |
| |
| davinci_mdio: mdio@4a101000 { |
| compatible = "ti,am4372-mdio","ti,cpsw-mdio","ti,davinci_mdio"; |
| reg = <0x4a101000 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "davinci_mdio"; |
| bus_freq = <1000000>; |
| status = "disabled"; |
| }; |
| |
| cpsw_emac0: slave@4a100200 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| cpsw_emac1: slave@4a100300 { |
| /* Filled in by U-Boot */ |
| mac-address = [ 00 00 00 00 00 00 ]; |
| }; |
| |
| phy_sel: cpsw-phy-sel@44e10650 { |
| compatible = "ti,am43xx-cpsw-phy-sel"; |
| reg= <0x44e10650 0x4>; |
| reg-names = "gmii-sel"; |
| }; |
| }; |
| |
| epwmss0: epwmss@48300000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x48300000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss0"; |
| status = "disabled"; |
| |
| ecap0: ecap@48300100 { |
| compatible = "ti,am4372-ecap", |
| "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48300100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm0: pwm@48300200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48300200 0x80>; |
| clocks = <&ehrpwm0_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss1: epwmss@48302000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x48302000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss1"; |
| status = "disabled"; |
| |
| ecap1: ecap@48302100 { |
| compatible = "ti,am4372-ecap", |
| "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48302100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm1: pwm@48302200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48302200 0x80>; |
| clocks = <&ehrpwm1_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss2: epwmss@48304000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x48304000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss2"; |
| status = "disabled"; |
| |
| ecap2: ecap@48304100 { |
| compatible = "ti,am4372-ecap", |
| "ti,am3352-ecap", |
| "ti,am33xx-ecap"; |
| #pwm-cells = <3>; |
| reg = <0x48304100 0x80>; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| status = "disabled"; |
| }; |
| |
| ehrpwm2: pwm@48304200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48304200 0x80>; |
| clocks = <&ehrpwm2_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss3: epwmss@48306000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x48306000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss3"; |
| status = "disabled"; |
| |
| ehrpwm3: pwm@48306200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48306200 0x80>; |
| clocks = <&ehrpwm3_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss4: epwmss@48308000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x48308000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss4"; |
| status = "disabled"; |
| |
| ehrpwm4: pwm@48308200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x48308200 0x80>; |
| clocks = <&ehrpwm4_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| epwmss5: epwmss@4830a000 { |
| compatible = "ti,am4372-pwmss","ti,am33xx-pwmss"; |
| reg = <0x4830a000 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "epwmss5"; |
| status = "disabled"; |
| |
| ehrpwm5: pwm@4830a200 { |
| compatible = "ti,am4372-ehrpwm", |
| "ti,am3352-ehrpwm", |
| "ti,am33xx-ehrpwm"; |
| #pwm-cells = <3>; |
| reg = <0x4830a200 0x80>; |
| clocks = <&ehrpwm5_tbclk>, <&l4ls_gclk>; |
| clock-names = "tbclk", "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| tscadc: tscadc@44e0d000 { |
| compatible = "ti,am3359-tscadc"; |
| reg = <0x44e0d000 0x1000>; |
| ti,hwmods = "adc_tsc"; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&adc_tsc_fck>; |
| clock-names = "fck"; |
| status = "disabled"; |
| dmas = <&edma 53 0>, <&edma 57 0>; |
| dma-names = "fifo0", "fifo1"; |
| |
| tsc { |
| compatible = "ti,am3359-tsc"; |
| }; |
| |
| adc { |
| #io-channel-cells = <1>; |
| compatible = "ti,am3359-adc"; |
| }; |
| |
| }; |
| |
| sham: sham@53100000 { |
| compatible = "ti,omap5-sham"; |
| ti,hwmods = "sham"; |
| reg = <0x53100000 0x300>; |
| dmas = <&edma 36 0>; |
| dma-names = "rx"; |
| interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| aes: aes@53501000 { |
| compatible = "ti,omap4-aes"; |
| ti,hwmods = "aes"; |
| reg = <0x53501000 0xa0>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&edma 6 0>, |
| <&edma 5 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| des: des@53701000 { |
| compatible = "ti,omap4-des"; |
| ti,hwmods = "des"; |
| reg = <0x53701000 0xa0>; |
| interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&edma 34 0>, |
| <&edma 33 0>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| rng: rng@48310000 { |
| compatible = "ti,omap4-rng"; |
| ti,hwmods = "rng"; |
| reg = <0x48310000 0x2000>; |
| interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| mcasp0: mcasp@48038000 { |
| compatible = "ti,am33xx-mcasp-audio"; |
| ti,hwmods = "mcasp0"; |
| reg = <0x48038000 0x2000>, |
| <0x46000000 0x400000>; |
| reg-names = "mpu", "dat"; |
| interrupts = <80>, <81>; |
| interrupt-names = "tx", "rx"; |
| status = "disabled"; |
| dmas = <&edma 8 2>, |
| <&edma 9 2>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| mcasp1: mcasp@4803C000 { |
| compatible = "ti,am33xx-mcasp-audio"; |
| ti,hwmods = "mcasp1"; |
| reg = <0x4803C000 0x2000>, |
| <0x46400000 0x400000>; |
| reg-names = "mpu", "dat"; |
| interrupts = <82>, <83>; |
| interrupt-names = "tx", "rx"; |
| status = "disabled"; |
| dmas = <&edma 10 2>, |
| <&edma 11 2>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| elm: elm@48080000 { |
| compatible = "ti,am3352-elm"; |
| reg = <0x48080000 0x2000>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "elm"; |
| clocks = <&l4ls_gclk>; |
| clock-names = "fck"; |
| status = "disabled"; |
| }; |
| |
| gpmc: gpmc@50000000 { |
| compatible = "ti,am3352-gpmc"; |
| ti,hwmods = "gpmc"; |
| dmas = <&edma 52 0>; |
| dma-names = "rxtx"; |
| clocks = <&l3s_gclk>; |
| clock-names = "fck"; |
| reg = <0x50000000 0x2000>; |
| interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; |
| gpmc,num-cs = <7>; |
| gpmc,num-waitpins = <2>; |
| #address-cells = <2>; |
| #size-cells = <1>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| ocp2scp0: ocp2scp@483a8000 { |
| compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "ocp2scp0"; |
| |
| usb2_phy1: phy@483a8000 { |
| compatible = "ti,am437x-usb2"; |
| reg = <0x483a8000 0x8000>; |
| syscon-phy-power = <&scm_conf 0x620>; |
| clocks = <&usb_phy0_always_on_clk32k>, |
| <&usb_otg_ss0_refclk960m>; |
| clock-names = "wkupclk", "refclk"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| ocp2scp1: ocp2scp@483e8000 { |
| compatible = "ti,am437x-ocp2scp", "ti,omap-ocp2scp"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| ti,hwmods = "ocp2scp1"; |
| |
| usb2_phy2: phy@483e8000 { |
| compatible = "ti,am437x-usb2"; |
| reg = <0x483e8000 0x8000>; |
| syscon-phy-power = <&scm_conf 0x628>; |
| clocks = <&usb_phy1_always_on_clk32k>, |
| <&usb_otg_ss1_refclk960m>; |
| clock-names = "wkupclk", "refclk"; |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| dwc3_1: omap_dwc3@48380000 { |
| compatible = "ti,am437x-dwc3"; |
| ti,hwmods = "usb_otg_ss0"; |
| reg = <0x48380000 0x10000>; |
| interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| utmi-mode = <1>; |
| ranges; |
| |
| usb1: usb@48390000 { |
| compatible = "synopsys,dwc3"; |
| reg = <0x48390000 0x10000>; |
| interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "peripheral", |
| "host", |
| "otg"; |
| phys = <&usb2_phy1>; |
| phy-names = "usb2-phy"; |
| maximum-speed = "high-speed"; |
| dr_mode = "otg"; |
| status = "disabled"; |
| snps,dis_u3_susphy_quirk; |
| snps,dis_u2_susphy_quirk; |
| }; |
| }; |
| |
| dwc3_2: omap_dwc3@483c0000 { |
| compatible = "ti,am437x-dwc3"; |
| ti,hwmods = "usb_otg_ss1"; |
| reg = <0x483c0000 0x10000>; |
| interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| utmi-mode = <1>; |
| ranges; |
| |
| usb2: usb@483d0000 { |
| compatible = "synopsys,dwc3"; |
| reg = <0x483d0000 0x10000>; |
| interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "peripheral", |
| "host", |
| "otg"; |
| phys = <&usb2_phy2>; |
| phy-names = "usb2-phy"; |
| maximum-speed = "high-speed"; |
| dr_mode = "otg"; |
| status = "disabled"; |
| snps,dis_u3_susphy_quirk; |
| snps,dis_u2_susphy_quirk; |
| }; |
| }; |
| |
| qspi: qspi@47900000 { |
| compatible = "ti,am4372-qspi"; |
| reg = <0x47900000 0x100>, |
| <0x30000000 0x4000000>; |
| reg-names = "qspi_base", "qspi_mmap"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| ti,hwmods = "qspi"; |
| interrupts = <0 138 0x4>; |
| num-cs = <4>; |
| status = "disabled"; |
| }; |
| |
| hdq: hdq@48347000 { |
| compatible = "ti,am4372-hdq"; |
| reg = <0x48347000 0x1000>; |
| interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&func_12m_clk>; |
| clock-names = "fck"; |
| ti,hwmods = "hdq1w"; |
| status = "disabled"; |
| }; |
| |
| dss: dss@4832a000 { |
| compatible = "ti,omap3-dss"; |
| reg = <0x4832a000 0x200>; |
| status = "disabled"; |
| ti,hwmods = "dss_core"; |
| clocks = <&disp_clk>; |
| clock-names = "fck"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| dispc: dispc@4832a400 { |
| compatible = "ti,omap3-dispc"; |
| reg = <0x4832a400 0x400>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "dss_dispc"; |
| clocks = <&disp_clk>; |
| clock-names = "fck"; |
| }; |
| |
| rfbi: rfbi@4832a800 { |
| compatible = "ti,omap3-rfbi"; |
| reg = <0x4832a800 0x100>; |
| ti,hwmods = "dss_rfbi"; |
| clocks = <&disp_clk>; |
| clock-names = "fck"; |
| status = "disabled"; |
| }; |
| }; |
| |
| ocmcram: ocmcram@40300000 { |
| compatible = "mmio-sram"; |
| reg = <0x40300000 0x40000>; /* 256k */ |
| }; |
| |
| dcan0: can@481cc000 { |
| compatible = "ti,am4372-d_can", "ti,am3352-d_can"; |
| ti,hwmods = "d_can0"; |
| clocks = <&dcan0_fck>; |
| clock-names = "fck"; |
| reg = <0x481cc000 0x2000>; |
| syscon-raminit = <&scm_conf 0x644 0>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| dcan1: can@481d0000 { |
| compatible = "ti,am4372-d_can", "ti,am3352-d_can"; |
| ti,hwmods = "d_can1"; |
| clocks = <&dcan1_fck>; |
| clock-names = "fck"; |
| reg = <0x481d0000 0x2000>; |
| syscon-raminit = <&scm_conf 0x644 1>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| vpfe0: vpfe@48326000 { |
| compatible = "ti,am437x-vpfe"; |
| reg = <0x48326000 0x2000>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "vpfe0"; |
| status = "disabled"; |
| }; |
| |
| vpfe1: vpfe@48328000 { |
| compatible = "ti,am437x-vpfe"; |
| reg = <0x48328000 0x2000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| ti,hwmods = "vpfe1"; |
| status = "disabled"; |
| }; |
| }; |
| }; |
| |
| /include/ "am43xx-clocks.dtsi" |