| /* |
| * Alchemy Db1550/Pb1550 board support |
| * |
| * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/gpio.h> |
| #include <linux/i2c.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <linux/interrupt.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/nand.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm.h> |
| #include <linux/spi/spi.h> |
| #include <linux/spi/flash.h> |
| #include <asm/bootinfo.h> |
| #include <asm/mach-au1x00/au1000.h> |
| #include <asm/mach-au1x00/gpio-au1000.h> |
| #include <asm/mach-au1x00/au1xxx_eth.h> |
| #include <asm/mach-au1x00/au1xxx_dbdma.h> |
| #include <asm/mach-au1x00/au1xxx_psc.h> |
| #include <asm/mach-au1x00/au1550_spi.h> |
| #include <asm/mach-au1x00/au1550nd.h> |
| #include <asm/mach-db1x00/bcsr.h> |
| #include <prom.h> |
| #include "platform.h" |
| |
| static void __init db1550_hw_setup(void) |
| { |
| void __iomem *base; |
| unsigned long v; |
| |
| /* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line) |
| * as well as PSC1_SYNC for AC97 on PB1550. |
| */ |
| v = alchemy_rdsys(AU1000_SYS_PINFUNC); |
| alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC); |
| |
| /* reset the AC97 codec now, the reset time in the psc-ac97 driver |
| * is apparently too short although it's ridiculous as it is. |
| */ |
| base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR); |
| __raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE, |
| base + PSC_SEL_OFFSET); |
| __raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET); |
| wmb(); |
| __raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET); |
| wmb(); |
| } |
| |
| int __init db1550_board_setup(void) |
| { |
| unsigned short whoami; |
| |
| bcsr_init(DB1550_BCSR_PHYS_ADDR, |
| DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS); |
| |
| whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */ |
| switch (BCSR_WHOAMI_BOARD(whoami)) { |
| case BCSR_WHOAMI_PB1550_SDR: |
| case BCSR_WHOAMI_PB1550_DDR: |
| bcsr_init(PB1550_BCSR_PHYS_ADDR, |
| PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS); |
| case BCSR_WHOAMI_DB1550: |
| break; |
| default: |
| return -ENODEV; |
| } |
| |
| pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d " \ |
| "Daughtercard ID %d\n", get_system_type(), |
| (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf); |
| |
| db1550_hw_setup(); |
| return 0; |
| } |
| |
| /*****************************************************************************/ |
| |
| static struct mtd_partition db1550_spiflash_parts[] = { |
| { |
| .name = "spi_flash", |
| .offset = 0, |
| .size = MTDPART_SIZ_FULL, |
| }, |
| }; |
| |
| static struct flash_platform_data db1550_spiflash_data = { |
| .name = "s25fl010", |
| .parts = db1550_spiflash_parts, |
| .nr_parts = ARRAY_SIZE(db1550_spiflash_parts), |
| .type = "m25p10", |
| }; |
| |
| static struct spi_board_info db1550_spi_devs[] __initdata = { |
| { |
| /* TI TMP121AIDBVR temp sensor */ |
| .modalias = "tmp121", |
| .max_speed_hz = 2400000, |
| .bus_num = 0, |
| .chip_select = 0, |
| .mode = SPI_MODE_0, |
| }, |
| { |
| /* Spansion S25FL001D0FMA SPI flash */ |
| .modalias = "m25p80", |
| .max_speed_hz = 2400000, |
| .bus_num = 0, |
| .chip_select = 1, |
| .mode = SPI_MODE_0, |
| .platform_data = &db1550_spiflash_data, |
| }, |
| }; |
| |
| static struct i2c_board_info db1550_i2c_devs[] __initdata = { |
| { I2C_BOARD_INFO("24c04", 0x52),}, /* AT24C04-10 I2C eeprom */ |
| { I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */ |
| { I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */ |
| }; |
| |
| /**********************************************************************/ |
| |
| static void au1550_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, |
| unsigned int ctrl) |
| { |
| struct nand_chip *this = mtd_to_nand(mtd); |
| unsigned long ioaddr = (unsigned long)this->IO_ADDR_W; |
| |
| ioaddr &= 0xffffff00; |
| |
| if (ctrl & NAND_CLE) { |
| ioaddr += MEM_STNAND_CMD; |
| } else if (ctrl & NAND_ALE) { |
| ioaddr += MEM_STNAND_ADDR; |
| } else { |
| /* assume we want to r/w real data by default */ |
| ioaddr += MEM_STNAND_DATA; |
| } |
| this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr; |
| if (cmd != NAND_CMD_NONE) { |
| __raw_writeb(cmd, this->IO_ADDR_W); |
| wmb(); |
| } |
| } |
| |
| static int au1550_nand_device_ready(struct mtd_info *mtd) |
| { |
| return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1; |
| } |
| |
| static struct mtd_partition db1550_nand_parts[] = { |
| { |
| .name = "NAND FS 0", |
| .offset = 0, |
| .size = 8 * 1024 * 1024, |
| }, |
| { |
| .name = "NAND FS 1", |
| .offset = MTDPART_OFS_APPEND, |
| .size = MTDPART_SIZ_FULL |
| }, |
| }; |
| |
| struct platform_nand_data db1550_nand_platdata = { |
| .chip = { |
| .nr_chips = 1, |
| .chip_offset = 0, |
| .nr_partitions = ARRAY_SIZE(db1550_nand_parts), |
| .partitions = db1550_nand_parts, |
| .chip_delay = 20, |
| }, |
| .ctrl = { |
| .dev_ready = au1550_nand_device_ready, |
| .cmd_ctrl = au1550_nand_cmd_ctrl, |
| }, |
| }; |
| |
| static struct resource db1550_nand_res[] = { |
| [0] = { |
| .start = 0x20000000, |
| .end = 0x200000ff, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| static struct platform_device db1550_nand_dev = { |
| .name = "gen_nand", |
| .num_resources = ARRAY_SIZE(db1550_nand_res), |
| .resource = db1550_nand_res, |
| .id = -1, |
| .dev = { |
| .platform_data = &db1550_nand_platdata, |
| } |
| }; |
| |
| static struct au1550nd_platdata pb1550_nand_pd = { |
| .parts = db1550_nand_parts, |
| .num_parts = ARRAY_SIZE(db1550_nand_parts), |
| .devwidth = 0, /* x8 NAND default, needs fixing up */ |
| }; |
| |
| static struct platform_device pb1550_nand_dev = { |
| .name = "au1550-nand", |
| .id = -1, |
| .resource = db1550_nand_res, |
| .num_resources = ARRAY_SIZE(db1550_nand_res), |
| .dev = { |
| .platform_data = &pb1550_nand_pd, |
| }, |
| }; |
| |
| static void __init pb1550_nand_setup(void) |
| { |
| int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) | |
| ((bcsr_read(BCSR_STATUS) >> 6) & 0x1); |
| |
| gpio_direction_input(206); /* de-assert NAND CS# */ |
| switch (boot_swapboot) { |
| case 0: case 2: case 8: case 0xC: case 0xD: |
| /* x16 NAND Flash */ |
| pb1550_nand_pd.devwidth = 1; |
| /* fallthrough */ |
| case 1: case 3: case 9: case 0xE: case 0xF: |
| /* x8 NAND, already set up */ |
| platform_device_register(&pb1550_nand_dev); |
| } |
| } |
| |
| /**********************************************************************/ |
| |
| static struct resource au1550_psc0_res[] = { |
| [0] = { |
| .start = AU1550_PSC0_PHYS_ADDR, |
| .end = AU1550_PSC0_PHYS_ADDR + 0xfff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = AU1550_PSC0_INT, |
| .end = AU1550_PSC0_INT, |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = AU1550_DSCR_CMD0_PSC0_TX, |
| .end = AU1550_DSCR_CMD0_PSC0_TX, |
| .flags = IORESOURCE_DMA, |
| }, |
| [3] = { |
| .start = AU1550_DSCR_CMD0_PSC0_RX, |
| .end = AU1550_DSCR_CMD0_PSC0_RX, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol) |
| { |
| if (cs) |
| bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL); |
| else |
| bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0); |
| } |
| |
| static struct au1550_spi_info db1550_spi_platdata = { |
| .mainclk_hz = 48000000, /* PSC0 clock: max. 2.4MHz SPI clk */ |
| .num_chipselect = 2, |
| .activate_cs = db1550_spi_cs_en, |
| }; |
| |
| static u64 spi_dmamask = DMA_BIT_MASK(32); |
| |
| static struct platform_device db1550_spi_dev = { |
| .dev = { |
| .dma_mask = &spi_dmamask, |
| .coherent_dma_mask = DMA_BIT_MASK(32), |
| .platform_data = &db1550_spi_platdata, |
| }, |
| .name = "au1550-spi", |
| .id = 0, /* bus number */ |
| .num_resources = ARRAY_SIZE(au1550_psc0_res), |
| .resource = au1550_psc0_res, |
| }; |
| |
| /**********************************************************************/ |
| |
| static struct resource au1550_psc1_res[] = { |
| [0] = { |
| .start = AU1550_PSC1_PHYS_ADDR, |
| .end = AU1550_PSC1_PHYS_ADDR + 0xfff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = AU1550_PSC1_INT, |
| .end = AU1550_PSC1_INT, |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = AU1550_DSCR_CMD0_PSC1_TX, |
| .end = AU1550_DSCR_CMD0_PSC1_TX, |
| .flags = IORESOURCE_DMA, |
| }, |
| [3] = { |
| .start = AU1550_DSCR_CMD0_PSC1_RX, |
| .end = AU1550_DSCR_CMD0_PSC1_RX, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static struct platform_device db1550_ac97_dev = { |
| .name = "au1xpsc_ac97", |
| .id = 1, /* PSC ID */ |
| .num_resources = ARRAY_SIZE(au1550_psc1_res), |
| .resource = au1550_psc1_res, |
| }; |
| |
| |
| static struct resource au1550_psc2_res[] = { |
| [0] = { |
| .start = AU1550_PSC2_PHYS_ADDR, |
| .end = AU1550_PSC2_PHYS_ADDR + 0xfff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = AU1550_PSC2_INT, |
| .end = AU1550_PSC2_INT, |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = AU1550_DSCR_CMD0_PSC2_TX, |
| .end = AU1550_DSCR_CMD0_PSC2_TX, |
| .flags = IORESOURCE_DMA, |
| }, |
| [3] = { |
| .start = AU1550_DSCR_CMD0_PSC2_RX, |
| .end = AU1550_DSCR_CMD0_PSC2_RX, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static struct platform_device db1550_i2c_dev = { |
| .name = "au1xpsc_smbus", |
| .id = 0, /* bus number */ |
| .num_resources = ARRAY_SIZE(au1550_psc2_res), |
| .resource = au1550_psc2_res, |
| }; |
| |
| /**********************************************************************/ |
| |
| static struct resource au1550_psc3_res[] = { |
| [0] = { |
| .start = AU1550_PSC3_PHYS_ADDR, |
| .end = AU1550_PSC3_PHYS_ADDR + 0xfff, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = AU1550_PSC3_INT, |
| .end = AU1550_PSC3_INT, |
| .flags = IORESOURCE_IRQ, |
| }, |
| [2] = { |
| .start = AU1550_DSCR_CMD0_PSC3_TX, |
| .end = AU1550_DSCR_CMD0_PSC3_TX, |
| .flags = IORESOURCE_DMA, |
| }, |
| [3] = { |
| .start = AU1550_DSCR_CMD0_PSC3_RX, |
| .end = AU1550_DSCR_CMD0_PSC3_RX, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static struct platform_device db1550_i2s_dev = { |
| .name = "au1xpsc_i2s", |
| .id = 3, /* PSC ID */ |
| .num_resources = ARRAY_SIZE(au1550_psc3_res), |
| .resource = au1550_psc3_res, |
| }; |
| |
| /**********************************************************************/ |
| |
| static struct platform_device db1550_stac_dev = { |
| .name = "ac97-codec", |
| .id = 1, /* on PSC1 */ |
| }; |
| |
| static struct platform_device db1550_ac97dma_dev = { |
| .name = "au1xpsc-pcm", |
| .id = 1, /* on PSC3 */ |
| }; |
| |
| static struct platform_device db1550_i2sdma_dev = { |
| .name = "au1xpsc-pcm", |
| .id = 3, /* on PSC3 */ |
| }; |
| |
| static struct platform_device db1550_sndac97_dev = { |
| .name = "db1550-ac97", |
| }; |
| |
| static struct platform_device db1550_sndi2s_dev = { |
| .name = "db1550-i2s", |
| }; |
| |
| /**********************************************************************/ |
| |
| static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) |
| { |
| if ((slot < 11) || (slot > 13) || pin == 0) |
| return -1; |
| if (slot == 11) |
| return (pin == 1) ? AU1550_PCI_INTC : 0xff; |
| if (slot == 12) { |
| switch (pin) { |
| case 1: return AU1550_PCI_INTB; |
| case 2: return AU1550_PCI_INTC; |
| case 3: return AU1550_PCI_INTD; |
| case 4: return AU1550_PCI_INTA; |
| } |
| } |
| if (slot == 13) { |
| switch (pin) { |
| case 1: return AU1550_PCI_INTA; |
| case 2: return AU1550_PCI_INTB; |
| case 3: return AU1550_PCI_INTC; |
| case 4: return AU1550_PCI_INTD; |
| } |
| } |
| return -1; |
| } |
| |
| static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin) |
| { |
| if ((slot < 12) || (slot > 13) || pin == 0) |
| return -1; |
| if (slot == 12) { |
| switch (pin) { |
| case 1: return AU1500_PCI_INTB; |
| case 2: return AU1500_PCI_INTC; |
| case 3: return AU1500_PCI_INTD; |
| case 4: return AU1500_PCI_INTA; |
| } |
| } |
| if (slot == 13) { |
| switch (pin) { |
| case 1: return AU1500_PCI_INTA; |
| case 2: return AU1500_PCI_INTB; |
| case 3: return AU1500_PCI_INTC; |
| case 4: return AU1500_PCI_INTD; |
| } |
| } |
| return -1; |
| } |
| |
| static struct resource alchemy_pci_host_res[] = { |
| [0] = { |
| .start = AU1500_PCI_PHYS_ADDR, |
| .end = AU1500_PCI_PHYS_ADDR + 0xfff, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| static struct alchemy_pci_platdata db1550_pci_pd = { |
| .board_map_irq = db1550_map_pci_irq, |
| }; |
| |
| static struct platform_device db1550_pci_host_dev = { |
| .dev.platform_data = &db1550_pci_pd, |
| .name = "alchemy-pci", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(alchemy_pci_host_res), |
| .resource = alchemy_pci_host_res, |
| }; |
| |
| /**********************************************************************/ |
| |
| static struct platform_device *db1550_devs[] __initdata = { |
| &db1550_i2c_dev, |
| &db1550_ac97_dev, |
| &db1550_spi_dev, |
| &db1550_i2s_dev, |
| &db1550_stac_dev, |
| &db1550_ac97dma_dev, |
| &db1550_i2sdma_dev, |
| &db1550_sndac97_dev, |
| &db1550_sndi2s_dev, |
| }; |
| |
| /* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */ |
| int __init db1550_pci_setup(int id) |
| { |
| if (id) |
| db1550_pci_pd.board_map_irq = pb1550_map_pci_irq; |
| return platform_device_register(&db1550_pci_host_dev); |
| } |
| |
| static void __init db1550_devices(void) |
| { |
| alchemy_gpio_direction_output(203, 0); /* red led on */ |
| |
| irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH); /* CD0# */ |
| irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH); /* CD1# */ |
| irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW); /* CARD0# */ |
| irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW); /* CARD1# */ |
| irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */ |
| irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */ |
| |
| db1x_register_pcmcia_socket( |
| AU1000_PCMCIA_ATTR_PHYS_ADDR, |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, |
| AU1000_PCMCIA_MEM_PHYS_ADDR, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, |
| AU1000_PCMCIA_IO_PHYS_ADDR, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, |
| AU1550_GPIO3_INT, AU1550_GPIO0_INT, |
| /*AU1550_GPIO21_INT*/0, 0, 0); |
| |
| db1x_register_pcmcia_socket( |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000, |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1, |
| AU1550_GPIO5_INT, AU1550_GPIO1_INT, |
| /*AU1550_GPIO22_INT*/0, 0, 1); |
| |
| platform_device_register(&db1550_nand_dev); |
| |
| alchemy_gpio_direction_output(202, 0); /* green led on */ |
| } |
| |
| static void __init pb1550_devices(void) |
| { |
| irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW); |
| irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW); |
| irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH); |
| |
| /* enable both PCMCIA card irqs in the shared line */ |
| alchemy_gpio2_enable_int(201); /* socket 0 card irq */ |
| alchemy_gpio2_enable_int(202); /* socket 1 card irq */ |
| |
| /* Pb1550, like all others, also has statuschange irqs; however they're |
| * wired up on one of the Au1550's shared GPIO201_205 line, which also |
| * services the PCMCIA card interrupts. So we ignore statuschange and |
| * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia |
| * drivers are used to shared irqs and b) statuschange isn't really use- |
| * ful anyway. |
| */ |
| db1x_register_pcmcia_socket( |
| AU1000_PCMCIA_ATTR_PHYS_ADDR, |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1, |
| AU1000_PCMCIA_MEM_PHYS_ADDR, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1, |
| AU1000_PCMCIA_IO_PHYS_ADDR, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1, |
| AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0); |
| |
| db1x_register_pcmcia_socket( |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000, |
| AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000, |
| AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000, |
| AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1, |
| AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1); |
| |
| pb1550_nand_setup(); |
| } |
| |
| int __init db1550_dev_setup(void) |
| { |
| int swapped, id; |
| struct clk *c; |
| |
| id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550); |
| |
| i2c_register_board_info(0, db1550_i2c_devs, |
| ARRAY_SIZE(db1550_i2c_devs)); |
| spi_register_board_info(db1550_spi_devs, |
| ARRAY_SIZE(db1550_i2c_devs)); |
| |
| c = clk_get(NULL, "psc0_intclk"); |
| if (!IS_ERR(c)) { |
| clk_set_rate(c, 50000000); |
| clk_prepare_enable(c); |
| clk_put(c); |
| } |
| c = clk_get(NULL, "psc2_intclk"); |
| if (!IS_ERR(c)) { |
| clk_set_rate(c, db1550_spi_platdata.mainclk_hz); |
| clk_prepare_enable(c); |
| clk_put(c); |
| } |
| |
| /* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */ |
| __raw_writel(PSC_SEL_CLK_SERCLK, |
| (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET); |
| wmb(); |
| __raw_writel(PSC_SEL_CLK_SERCLK, |
| (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET); |
| wmb(); |
| /* SPI/I2C use internally supplied 50MHz source */ |
| __raw_writel(PSC_SEL_CLK_INTCLK, |
| (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET); |
| wmb(); |
| __raw_writel(PSC_SEL_CLK_INTCLK, |
| (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET); |
| wmb(); |
| |
| id ? pb1550_devices() : db1550_devices(); |
| |
| swapped = bcsr_read(BCSR_STATUS) & |
| (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT); |
| db1x_register_norflash(128 << 20, 4, swapped); |
| |
| return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs)); |
| } |