arch/blackfin/mach-bf537/boards/cm_bf537e.c - kernel/msm-4.19 - Gitiles

 /*
  * Copyright 2004-2009 Analog Devices Inc.
  *           2008-2009 Bluetechnix
  *                2005 National ICT Australia (NICTA)
  *                      Aidan Williams <aidan@nicta.com.au>
  *
  * Licensed under the GPL-2 or later.
  */

 #include <linux/device.h>
 #include <linux/export.h>
 #include <linux/etherdevice.h>
 #include <linux/platform_device.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
 #if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 #include <linux/usb/isp1362.h>
 #endif
 #include <linux/ata_platform.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
 #include <asm/dma.h>
 #include <asm/bfin5xx_spi.h>
 #include <asm/portmux.h>
 #include <asm/dpmc.h>
 #include <asm/bfin_sport.h>

 /*
  * Name the Board for the /proc/cpuinfo
  */
 const char bfin_board_name[] = "Bluetechnix CM BF537E";

 #if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 /* all SPI peripherals info goes here */

 #if IS_ENABLED(CONFIG_MTD_M25P80)
 static struct mtd_partition bfin_spi_flash_partitions[] = {
 	{
 		.name = "bootloader(spi)",
 		.size = 0x00020000,
 		.offset = 0,
 		.mask_flags = MTD_CAP_ROM
 	}, {
 		.name = "linux kernel(spi)",
 		.size = 0xe0000,
 		.offset = 0x20000
 	}, {
 		.name = "file system(spi)",
 		.size = 0x700000,
 		.offset = 0x00100000,
 	}
 };

 static struct flash_platform_data bfin_spi_flash_data = {
 	.name = "m25p80",
 	.parts = bfin_spi_flash_partitions,
 	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 	.type = "m25p64",
 };

 /* SPI flash chip (m25p64) */
 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 	.enable_dma = 0,         /* use dma transfer with this chip*/
 };
 #endif

 #if IS_ENABLED(CONFIG_MMC_SPI)
 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 	.enable_dma = 0,
 };
 #endif

 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 #if IS_ENABLED(CONFIG_MTD_M25P80)
 	{
 		/* the modalias must be the same as spi device driver name */
 		.modalias = "m25p80", /* Name of spi_driver for this device */
 		.max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0, /* Framework bus number */
 		.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 		.platform_data = &bfin_spi_flash_data,
 		.controller_data = &spi_flash_chip_info,
 		.mode = SPI_MODE_3,
 	},
 #endif

 #if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
 	{
 		.modalias = "ad183x",
 		.max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 4,
 	},
 #endif

 #if IS_ENABLED(CONFIG_MMC_SPI)
 	{
 		.modalias = "mmc_spi",
 		.max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 		.bus_num = 0,
 		.chip_select = 1,
 		.controller_data = &mmc_spi_chip_info,
 		.mode = SPI_MODE_3,
 	},
 #endif
 };

 /* SPI (0) */
 static struct resource bfin_spi0_resource[] = {
 	[0] = {
 		.start = SPI0_REGBASE,
 		.end   = SPI0_REGBASE + 0xFF,
 		.flags = IORESOURCE_MEM,
 		},
 	[1] = {
 		.start = CH_SPI,
 		.end   = CH_SPI,
 		.flags = IORESOURCE_DMA,
 	},
 	[2] = {
 		.start = IRQ_SPI,
 		.end   = IRQ_SPI,
 		.flags = IORESOURCE_IRQ,
 	},
 };

 /* SPI controller data */
 static struct bfin5xx_spi_master bfin_spi0_info = {
 	.num_chipselect = 8,
 	.enable_dma = 1,  /* master has the ability to do dma transfer */
 	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 };

 static struct platform_device bfin_spi0_device = {
 	.name = "bfin-spi",
 	.id = 0, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
 	.resource = bfin_spi0_resource,
 	.dev = {
 		.platform_data = &bfin_spi0_info, /* Passed to driver */
 	},
 };
 #endif  /* spi master and devices */

 #if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)

 /* SPORT SPI controller data */
 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
 	.num_chipselect = MAX_BLACKFIN_GPIOS,
 	.enable_dma = 0,  /* master don't support DMA */
 	.pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
 		P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
 };

 static struct resource bfin_sport_spi0_resource[] = {
 	[0] = {
 		.start = SPORT0_TCR1,
 		.end   = SPORT0_TCR1 + 0xFF,
 		.flags = IORESOURCE_MEM,
 		},
 	[1] = {
 		.start = IRQ_SPORT0_ERROR,
 		.end   = IRQ_SPORT0_ERROR,
 		.flags = IORESOURCE_IRQ,
 		},
 };

 static struct platform_device bfin_sport_spi0_device = {
 	.name = "bfin-sport-spi",
 	.id = 1, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
 	.resource = bfin_sport_spi0_resource,
 	.dev = {
 		.platform_data = &bfin_sport_spi0_info, /* Passed to driver */
 	},
 };

 static struct bfin5xx_spi_master bfin_sport_spi1_info = {
 	.num_chipselect = MAX_BLACKFIN_GPIOS,
 	.enable_dma = 0,  /* master don't support DMA */
 	.pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
 		P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
 };

 static struct resource bfin_sport_spi1_resource[] = {
 	[0] = {
 		.start = SPORT1_TCR1,
 		.end   = SPORT1_TCR1 + 0xFF,
 		.flags = IORESOURCE_MEM,
 		},
 	[1] = {
 		.start = IRQ_SPORT1_ERROR,
 		.end   = IRQ_SPORT1_ERROR,
 		.flags = IORESOURCE_IRQ,
 		},
 };

 static struct platform_device bfin_sport_spi1_device = {
 	.name = "bfin-sport-spi",
 	.id = 2, /* Bus number */
 	.num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
 	.resource = bfin_sport_spi1_resource,
 	.dev = {
 		.platform_data = &bfin_sport_spi1_info, /* Passed to driver */
 	},
 };

 #endif  /* sport spi master and devices */

 #if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 static struct platform_device rtc_device = {
 	.name = "rtc-bfin",
 	.id   = -1,
 };
 #endif

 #if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 static struct platform_device hitachi_fb_device = {
 	.name = "hitachi-tx09",
 };
 #endif

 #if IS_ENABLED(CONFIG_SMC91X)
 #include <linux/smc91x.h>

 static struct smc91x_platdata smc91x_info = {
 	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 	.leda = RPC_LED_100_10,
 	.ledb = RPC_LED_TX_RX,
 };

 static struct resource smc91x_resources[] = {
 	{
 		.start = 0x20200300,
 		.end = 0x20200300 + 16,
 		.flags = IORESOURCE_MEM,
 	}, {
 		.start = IRQ_PF14,
 		.end = IRQ_PF14,
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 		},
 };

 static struct platform_device smc91x_device = {
 	.name = "smc91x",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(smc91x_resources),
 	.resource = smc91x_resources,
 	.dev	= {
 		.platform_data	= &smc91x_info,
 	},
 };
 #endif

 #if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 static struct resource isp1362_hcd_resources[] = {
 	{
 		.start = 0x20308000,
 		.end = 0x20308000,
 		.flags = IORESOURCE_MEM,
 	}, {
 		.start = 0x20308004,
 		.end = 0x20308004,
 		.flags = IORESOURCE_MEM,
 	}, {
 		.start = IRQ_PG15,
 		.end = IRQ_PG15,
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
 	},
 };

 static struct isp1362_platform_data isp1362_priv = {
 	.sel15Kres = 1,
 	.clknotstop = 0,
 	.oc_enable = 0,
 	.int_act_high = 0,
 	.int_edge_triggered = 0,
 	.remote_wakeup_connected = 0,
 	.no_power_switching = 1,
 	.power_switching_mode = 0,
 };

 static struct platform_device isp1362_hcd_device = {
 	.name = "isp1362-hcd",
 	.id = 0,
 	.dev = {
 		.platform_data = &isp1362_priv,
 	},
 	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 	.resource = isp1362_hcd_resources,
 };
 #endif

 #if IS_ENABLED(CONFIG_USB_NET2272)
 static struct resource net2272_bfin_resources[] = {
 	{
 		.start = 0x20300000,
 		.end = 0x20300000 + 0x100,
 		.flags = IORESOURCE_MEM,
 	}, {
 		.start = IRQ_PG13,
 		.end = IRQ_PG13,
 		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 	},
 };

 static struct platform_device net2272_bfin_device = {
 	.name = "net2272",
 	.id = -1,
 	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
 	.resource = net2272_bfin_resources,
 };
 #endif

 #if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 static struct mtd_partition cm_partitions[] = {
 	{
 		.name   = "bootloader(nor)",
 		.size   = 0x40000,
 		.offset = 0,
 	}, {
 		.name   = "linux kernel(nor)",
 		.size   = 0x100000,
 		.offset = MTDPART_OFS_APPEND,
 	}, {
 		.name   = "file system(nor)",
 		.size   = MTDPART_SIZ_FULL,
 		.offset = MTDPART_OFS_APPEND,
 	}
 };

 static struct physmap_flash_data cm_flash_data = {
 	.width    = 2,
 	.parts    = cm_partitions,
 	.nr_parts = ARRAY_SIZE(cm_partitions),
 };

 static unsigned cm_flash_gpios[] = { GPIO_PF4 };

 static struct resource cm_flash_resource[] = {
 	{
 		.name  = "cfi_probe",
 		.start = 0x20000000,
 		.end   = 0x201fffff,
 		.flags = IORESOURCE_MEM,
 	}, {
 		.start = (unsigned long)cm_flash_gpios,
 		.end   = ARRAY_SIZE(cm_flash_gpios),
 		.flags = IORESOURCE_IRQ,
 	}
 };

 static struct platform_device cm_flash_device = {
 	.name          = "gpio-addr-flash",
 	.id            = 0,
 	.dev = {
 		.platform_data = &cm_flash_data,
 	},
 	.num_resources = ARRAY_SIZE(cm_flash_resource),
 	.resource      = cm_flash_resource,
 };
 #endif

 #if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 static struct resource bfin_uart0_resources[] = {
 	{
 		.start = UART0_THR,
 		.end = UART0_GCTL+2,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_UART0_TX,
 		.end = IRQ_UART0_TX,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_UART0_RX,
 		.end = IRQ_UART0_RX,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_UART0_ERROR,
 		.end = IRQ_UART0_ERROR,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = CH_UART0_TX,
 		.end = CH_UART0_TX,
 		.flags = IORESOURCE_DMA,
 	},
 	{
 		.start = CH_UART0_RX,
 		.end = CH_UART0_RX,
 		.flags = IORESOURCE_DMA,
 	},
 #ifdef CONFIG_BFIN_UART0_CTSRTS
 	{
 		/*
 		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 		 */
 		.start = -1,
 		.end = -1,
 		.flags = IORESOURCE_IO,
 	},
 	{
 		/*
 		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 		 */
 		.start = -1,
 		.end = -1,
 		.flags = IORESOURCE_IO,
 	},
 #endif
 };

 static unsigned short bfin_uart0_peripherals[] = {
 	P_UART0_TX, P_UART0_RX, 0
 };

 static struct platform_device bfin_uart0_device = {
 	.name = "bfin-uart",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
 	.resource = bfin_uart0_resources,
 	.dev = {
 		.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 	},
 };
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
 static struct resource bfin_uart1_resources[] = {
 	{
 		.start = UART1_THR,
 		.end = UART1_GCTL+2,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_UART1_TX,
 		.end = IRQ_UART1_TX,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_UART1_RX,
 		.end = IRQ_UART1_RX,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_UART1_ERROR,
 		.end = IRQ_UART1_ERROR,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = CH_UART1_TX,
 		.end = CH_UART1_TX,
 		.flags = IORESOURCE_DMA,
 	},
 	{
 		.start = CH_UART1_RX,
 		.end = CH_UART1_RX,
 		.flags = IORESOURCE_DMA,
 	},
 #ifdef CONFIG_BFIN_UART1_CTSRTS
 	{
 		/*
 		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 		 */
 		.start = -1,
 		.end = -1,
 		.flags = IORESOURCE_IO,
 	},
 	{
 		/*
 		 * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
 		 */
 		.start = -1,
 		.end = -1,
 		.flags = IORESOURCE_IO,
 	},
 #endif
 };

 static unsigned short bfin_uart1_peripherals[] = {
 	P_UART1_TX, P_UART1_RX, 0
 };

 static struct platform_device bfin_uart1_device = {
 	.name = "bfin-uart",
 	.id = 1,
 	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
 	.resource = bfin_uart1_resources,
 	.dev = {
 		.platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 	},
 };
 #endif
 #endif

 #if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 static struct resource bfin_sir0_resources[] = {
 	{
 		.start = 0xFFC00400,
 		.end = 0xFFC004FF,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_UART0_RX,
 		.end = IRQ_UART0_RX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = CH_UART0_RX,
 		.end = CH_UART0_RX+1,
 		.flags = IORESOURCE_DMA,
 	},
 };
 static struct platform_device bfin_sir0_device = {
 	.name = "bfin_sir",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
 	.resource = bfin_sir0_resources,
 };
 #endif
 #ifdef CONFIG_BFIN_SIR1
 static struct resource bfin_sir1_resources[] = {
 	{
 		.start = 0xFFC02000,
 		.end = 0xFFC020FF,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_UART1_RX,
 		.end = IRQ_UART1_RX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = CH_UART1_RX,
 		.end = CH_UART1_RX+1,
 		.flags = IORESOURCE_DMA,
 	},
 };
 static struct platform_device bfin_sir1_device = {
 	.name = "bfin_sir",
 	.id = 1,
 	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
 	.resource = bfin_sir1_resources,
 };
 #endif
 #endif

 #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};

 static struct resource bfin_twi0_resource[] = {
 	[0] = {
 		.start = TWI0_REGBASE,
 		.end   = TWI0_REGBASE,
 		.flags = IORESOURCE_MEM,
 	},
 	[1] = {
 		.start = IRQ_TWI,
 		.end   = IRQ_TWI,
 		.flags = IORESOURCE_IRQ,
 	},
 };

 static struct platform_device i2c_bfin_twi_device = {
 	.name = "i2c-bfin-twi",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
 	.resource = bfin_twi0_resource,
 	.dev = {
 		.platform_data = &bfin_twi0_pins,
 	},
 };
 #endif

 #if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
 || IS_ENABLED(CONFIG_BFIN_SPORT)
 unsigned short bfin_sport0_peripherals[] = {
 	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
 };
 #endif
 #if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 static struct resource bfin_sport0_uart_resources[] = {
 	{
 		.start = SPORT0_TCR1,
 		.end = SPORT0_MRCS3+4,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_SPORT0_RX,
 		.end = IRQ_SPORT0_RX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_SPORT0_ERROR,
 		.end = IRQ_SPORT0_ERROR,
 		.flags = IORESOURCE_IRQ,
 	},
 };

 static struct platform_device bfin_sport0_uart_device = {
 	.name = "bfin-sport-uart",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
 	.resource = bfin_sport0_uart_resources,
 	.dev = {
 		.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
 	},
 };
 #endif
 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 static struct resource bfin_sport1_uart_resources[] = {
 	{
 		.start = SPORT1_TCR1,
 		.end = SPORT1_MRCS3+4,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_SPORT1_RX,
 		.end = IRQ_SPORT1_RX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_SPORT1_ERROR,
 		.end = IRQ_SPORT1_ERROR,
 		.flags = IORESOURCE_IRQ,
 	},
 };

 static unsigned short bfin_sport1_peripherals[] = {
 	P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 	P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
 };

 static struct platform_device bfin_sport1_uart_device = {
 	.name = "bfin-sport-uart",
 	.id = 1,
 	.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
 	.resource = bfin_sport1_uart_resources,
 	.dev = {
 		.platform_data = &bfin_sport1_peripherals, /* Passed to driver */
 	},
 };
 #endif
 #endif
 #if IS_ENABLED(CONFIG_BFIN_SPORT)
 static struct resource bfin_sport0_resources[] = {
 	{
 		.start = SPORT0_TCR1,
 		.end = SPORT0_MRCS3+4,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = IRQ_SPORT0_RX,
 		.end = IRQ_SPORT0_RX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_SPORT0_TX,
 		.end = IRQ_SPORT0_TX+1,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = IRQ_SPORT0_ERROR,
 		.end = IRQ_SPORT0_ERROR,
 		.flags = IORESOURCE_IRQ,
 	},
 	{
 		.start = CH_SPORT0_TX,
 		.end = CH_SPORT0_TX,
 		.flags = IORESOURCE_DMA,
 	},
 	{
 		.start = CH_SPORT0_RX,
 		.end = CH_SPORT0_RX,
 		.flags = IORESOURCE_DMA,
 	},
 };
 static struct platform_device bfin_sport0_device = {
 	.name = "bfin_sport_raw",
 	.id = 0,
 	.num_resources = ARRAY_SIZE(bfin_sport0_resources),
 	.resource = bfin_sport0_resources,
 	.dev = {
 		.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
 	},
 };
 #endif

 #if IS_ENABLED(CONFIG_BFIN_MAC)
 #include <linux/bfin_mac.h>
 static const unsigned short bfin_mac_peripherals[] = P_MII0;

 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 	{
 		.addr = 1,
 		.irq = IRQ_MAC_PHYINT,
 	},
 };

 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
 	.phydev_number = 1,
 	.phydev_data = bfin_phydev_data,
 	.phy_mode = PHY_INTERFACE_MODE_MII,
 	.mac_peripherals = bfin_mac_peripherals,
 };

 static struct platform_device bfin_mii_bus = {
 	.name = "bfin_mii_bus",
 	.dev = {
 		.platform_data = &bfin_mii_bus_data,
 	}
 };

 static struct platform_device bfin_mac_device = {
 	.name = "bfin_mac",
 	.dev = {
 		.platform_data = &bfin_mii_bus,
 	}
 };
 #endif

 #if IS_ENABLED(CONFIG_PATA_PLATFORM)
 #define PATA_INT	IRQ_PF14

 static struct pata_platform_info bfin_pata_platform_data = {
 	.ioport_shift = 2,
 	.irq_type = IRQF_TRIGGER_HIGH,
 };

 static struct resource bfin_pata_resources[] = {
 	{
 		.start = 0x2030C000,
 		.end = 0x2030C01F,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = 0x2030D018,
 		.end = 0x2030D01B,
 		.flags = IORESOURCE_MEM,
 	},
 	{
 		.start = PATA_INT,
 		.end = PATA_INT,
 		.flags = IORESOURCE_IRQ,
 	},
 };

 static struct platform_device bfin_pata_device = {
 	.name = "pata_platform",
 	.id = -1,
 	.num_resources = ARRAY_SIZE(bfin_pata_resources),
 	.resource = bfin_pata_resources,
 	.dev = {
 		.platform_data = &bfin_pata_platform_data,
 	}
 };
 #endif

 static const unsigned int cclk_vlev_datasheet[] =
 {
 	VRPAIR(VLEV_085, 250000000),
 	VRPAIR(VLEV_090, 376000000),
 	VRPAIR(VLEV_095, 426000000),
 	VRPAIR(VLEV_100, 426000000),
 	VRPAIR(VLEV_105, 476000000),
 	VRPAIR(VLEV_110, 476000000),
 	VRPAIR(VLEV_115, 476000000),
 	VRPAIR(VLEV_120, 500000000),
 	VRPAIR(VLEV_125, 533000000),
 	VRPAIR(VLEV_130, 600000000),
 };

 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 	.tuple_tab = cclk_vlev_datasheet,
 	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 	.vr_settling_time = 25 /* us */,
 };

 static struct platform_device bfin_dpmc = {
 	.name = "bfin dpmc",
 	.dev = {
 		.platform_data = &bfin_dmpc_vreg_data,
 	},
 };

 static struct platform_device *cm_bf537e_devices[] __initdata = {

 	&bfin_dpmc,

 #if IS_ENABLED(CONFIG_BFIN_SPORT)
 	&bfin_sport0_device,
 #endif

 #if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
 	&hitachi_fb_device,
 #endif

 #if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
 	&rtc_device,
 #endif

 #if IS_ENABLED(CONFIG_SERIAL_BFIN)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
 	&bfin_uart1_device,
 #endif
 #endif

 #if IS_ENABLED(CONFIG_BFIN_SIR)
 #ifdef CONFIG_BFIN_SIR0
 	&bfin_sir0_device,
 #endif
 #ifdef CONFIG_BFIN_SIR1
 	&bfin_sir1_device,
 #endif
 #endif

 #if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
 	&i2c_bfin_twi_device,
 #endif

 #if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 	&bfin_sport1_uart_device,
 #endif
 #endif

 #if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
 	&isp1362_hcd_device,
 #endif

 #if IS_ENABLED(CONFIG_SMC91X)
 	&smc91x_device,
 #endif

 #if IS_ENABLED(CONFIG_BFIN_MAC)
 	&bfin_mii_bus,
 	&bfin_mac_device,
 #endif

 #if IS_ENABLED(CONFIG_USB_NET2272)
 	&net2272_bfin_device,
 #endif

 #if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	&bfin_spi0_device,
 #endif

 #if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
 	&bfin_sport_spi0_device,
 	&bfin_sport_spi1_device,
 #endif

 #if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	&bfin_pata_device,
 #endif

 #if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
 	&cm_flash_device,
 #endif
 };

 static int __init net2272_init(void)
 {
 #if IS_ENABLED(CONFIG_USB_NET2272)
 	int ret;

 	ret = gpio_request(GPIO_PG14, "net2272");
 	if (ret)
 		return ret;

 	/* Reset USB Chip, PG14 */
 	gpio_direction_output(GPIO_PG14, 0);
 	mdelay(2);
 	gpio_set_value(GPIO_PG14, 1);
 #endif

 	return 0;
 }

 static int __init cm_bf537e_init(void)
 {
 	printk(KERN_INFO "%s(): registering device resources\n", __func__);
 	platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
 #if IS_ENABLED(CONFIG_SPI_BFIN5XX)
 	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
 #endif

 #if IS_ENABLED(CONFIG_PATA_PLATFORM)
 	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
 #endif

 	if (net2272_init())
 		pr_warning("unable to configure net2272; it probably won't work\n");

 	return 0;
 }

 arch_initcall(cm_bf537e_init);

 static struct platform_device *cm_bf537e_early_devices[] __initdata = {
 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
 #ifdef CONFIG_SERIAL_BFIN_UART0
 	&bfin_uart0_device,
 #endif
 #ifdef CONFIG_SERIAL_BFIN_UART1
 	&bfin_uart1_device,
 #endif
 #endif

 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 	&bfin_sport0_uart_device,
 #endif
 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 	&bfin_sport1_uart_device,
 #endif
 #endif
 };

 void __init native_machine_early_platform_add_devices(void)
 {
 	printk(KERN_INFO "register early platform devices\n");
 	early_platform_add_devices(cm_bf537e_early_devices,
 		ARRAY_SIZE(cm_bf537e_early_devices));
 }

 int bfin_get_ether_addr(char *addr)
 {
 	return 1;
 }
 EXPORT_SYMBOL(bfin_get_ether_addr);
	/*
	* Copyright 2004-2009 Analog Devices Inc.
	* 2008-2009 Bluetechnix
	* 2005 National ICT Australia (NICTA)
	* Aidan Williams <aidan@nicta.com.au>
	*
	* Licensed under the GPL-2 or later.
	*/

	#include <linux/device.h>
	#include <linux/export.h>
	#include <linux/etherdevice.h>
	#include <linux/platform_device.h>
	#include <linux/mtd/mtd.h>
	#include <linux/mtd/partitions.h>
	#include <linux/mtd/physmap.h>
	#include <linux/spi/spi.h>
	#include <linux/spi/flash.h>
	#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
	#include <linux/usb/isp1362.h>
	#endif
	#include <linux/ata_platform.h>
	#include <linux/irq.h>
	#include <linux/gpio.h>
	#include <asm/dma.h>
	#include <asm/bfin5xx_spi.h>
	#include <asm/portmux.h>
	#include <asm/dpmc.h>
	#include <asm/bfin_sport.h>

	/*
	* Name the Board for the /proc/cpuinfo
	*/
	const char bfin_board_name[] = "Bluetechnix CM BF537E";

	#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
	/* all SPI peripherals info goes here */

	#if IS_ENABLED(CONFIG_MTD_M25P80)
	static struct mtd_partition bfin_spi_flash_partitions[] = {
	{
	.name = "bootloader(spi)",
	.size = 0x00020000,
	.offset = 0,
	.mask_flags = MTD_CAP_ROM
	}, {
	.name = "linux kernel(spi)",
	.size = 0xe0000,
	.offset = 0x20000
	}, {
	.name = "file system(spi)",
	.size = 0x700000,
	.offset = 0x00100000,
	}
	};

	static struct flash_platform_data bfin_spi_flash_data = {
	.name = "m25p80",
	.parts = bfin_spi_flash_partitions,
	.nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
	.type = "m25p64",
	};

	/* SPI flash chip (m25p64) */
	static struct bfin5xx_spi_chip spi_flash_chip_info = {
	.enable_dma = 0, /* use dma transfer with this chip*/
	};
	#endif

	#if IS_ENABLED(CONFIG_MMC_SPI)
	static struct bfin5xx_spi_chip mmc_spi_chip_info = {
	.enable_dma = 0,
	};
	#endif

	static struct spi_board_info bfin_spi_board_info[] __initdata = {
	#if IS_ENABLED(CONFIG_MTD_M25P80)
	{
	/* the modalias must be the same as spi device driver name */
	.modalias = "m25p80", /* Name of spi_driver for this device */
	.max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
	.bus_num = 0, /* Framework bus number */
	.chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
	.platform_data = &bfin_spi_flash_data,
	.controller_data = &spi_flash_chip_info,
	.mode = SPI_MODE_3,
	},
	#endif

	#if IS_ENABLED(CONFIG_SND_BF5XX_SOC_AD183X)
	{
	.modalias = "ad183x",
	.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
	.bus_num = 0,
	.chip_select = 4,
	},
	#endif

	#if IS_ENABLED(CONFIG_MMC_SPI)
	{
	.modalias = "mmc_spi",
	.max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
	.bus_num = 0,
	.chip_select = 1,
	.controller_data = &mmc_spi_chip_info,
	.mode = SPI_MODE_3,
	},
	#endif
	};

	/* SPI (0) */
	static struct resource bfin_spi0_resource[] = {
	[0] = {
	.start = SPI0_REGBASE,
	.end = SPI0_REGBASE + 0xFF,
	.flags = IORESOURCE_MEM,
	},
	[1] = {
	.start = CH_SPI,
	.end = CH_SPI,
	.flags = IORESOURCE_DMA,
	},
	[2] = {
	.start = IRQ_SPI,
	.end = IRQ_SPI,
	.flags = IORESOURCE_IRQ,
	},
	};

	/* SPI controller data */
	static struct bfin5xx_spi_master bfin_spi0_info = {
	.num_chipselect = 8,
	.enable_dma = 1, /* master has the ability to do dma transfer */
	.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
	};

	static struct platform_device bfin_spi0_device = {
	.name = "bfin-spi",
	.id = 0, /* Bus number */
	.num_resources = ARRAY_SIZE(bfin_spi0_resource),
	.resource = bfin_spi0_resource,
	.dev = {
	.platform_data = &bfin_spi0_info, /* Passed to driver */
	},
	};
	#endif /* spi master and devices */

	#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)

	/* SPORT SPI controller data */
	static struct bfin5xx_spi_master bfin_sport_spi0_info = {
	.num_chipselect = MAX_BLACKFIN_GPIOS,
	.enable_dma = 0, /* master don't support DMA */
	.pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
	P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
	};

	static struct resource bfin_sport_spi0_resource[] = {
	[0] = {
	.start = SPORT0_TCR1,
	.end = SPORT0_TCR1 + 0xFF,
	.flags = IORESOURCE_MEM,
	},
	[1] = {
	.start = IRQ_SPORT0_ERROR,
	.end = IRQ_SPORT0_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	};

	static struct platform_device bfin_sport_spi0_device = {
	.name = "bfin-sport-spi",
	.id = 1, /* Bus number */
	.num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
	.resource = bfin_sport_spi0_resource,
	.dev = {
	.platform_data = &bfin_sport_spi0_info, /* Passed to driver */
	},
	};

	static struct bfin5xx_spi_master bfin_sport_spi1_info = {
	.num_chipselect = MAX_BLACKFIN_GPIOS,
	.enable_dma = 0, /* master don't support DMA */
	.pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
	P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
	};

	static struct resource bfin_sport_spi1_resource[] = {
	[0] = {
	.start = SPORT1_TCR1,
	.end = SPORT1_TCR1 + 0xFF,
	.flags = IORESOURCE_MEM,
	},
	[1] = {
	.start = IRQ_SPORT1_ERROR,
	.end = IRQ_SPORT1_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	};

	static struct platform_device bfin_sport_spi1_device = {
	.name = "bfin-sport-spi",
	.id = 2, /* Bus number */
	.num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
	.resource = bfin_sport_spi1_resource,
	.dev = {
	.platform_data = &bfin_sport_spi1_info, /* Passed to driver */
	},
	};

	#endif /* sport spi master and devices */

	#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
	static struct platform_device rtc_device = {
	.name = "rtc-bfin",
	.id = -1,
	};
	#endif

	#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
	static struct platform_device hitachi_fb_device = {
	.name = "hitachi-tx09",
	};
	#endif

	#if IS_ENABLED(CONFIG_SMC91X)
	#include <linux/smc91x.h>

	static struct smc91x_platdata smc91x_info = {
	.flags = SMC91X_USE_16BIT \| SMC91X_NOWAIT,
	.leda = RPC_LED_100_10,
	.ledb = RPC_LED_TX_RX,
	};

	static struct resource smc91x_resources[] = {
	{
	.start = 0x20200300,
	.end = 0x20200300 + 16,
	.flags = IORESOURCE_MEM,
	}, {
	.start = IRQ_PF14,
	.end = IRQ_PF14,
	.flags = IORESOURCE_IRQ \| IORESOURCE_IRQ_HIGHLEVEL,
	},
	};

	static struct platform_device smc91x_device = {
	.name = "smc91x",
	.id = 0,
	.num_resources = ARRAY_SIZE(smc91x_resources),
	.resource = smc91x_resources,
	.dev = {
	.platform_data = &smc91x_info,
	},
	};
	#endif

	#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
	static struct resource isp1362_hcd_resources[] = {
	{
	.start = 0x20308000,
	.end = 0x20308000,
	.flags = IORESOURCE_MEM,
	}, {
	.start = 0x20308004,
	.end = 0x20308004,
	.flags = IORESOURCE_MEM,
	}, {
	.start = IRQ_PG15,
	.end = IRQ_PG15,
	.flags = IORESOURCE_IRQ \| IORESOURCE_IRQ_LOWEDGE,
	},
	};

	static struct isp1362_platform_data isp1362_priv = {
	.sel15Kres = 1,
	.clknotstop = 0,
	.oc_enable = 0,
	.int_act_high = 0,
	.int_edge_triggered = 0,
	.remote_wakeup_connected = 0,
	.no_power_switching = 1,
	.power_switching_mode = 0,
	};

	static struct platform_device isp1362_hcd_device = {
	.name = "isp1362-hcd",
	.id = 0,
	.dev = {
	.platform_data = &isp1362_priv,
	},
	.num_resources = ARRAY_SIZE(isp1362_hcd_resources),
	.resource = isp1362_hcd_resources,
	};
	#endif

	#if IS_ENABLED(CONFIG_USB_NET2272)
	static struct resource net2272_bfin_resources[] = {
	{
	.start = 0x20300000,
	.end = 0x20300000 + 0x100,
	.flags = IORESOURCE_MEM,
	}, {
	.start = IRQ_PG13,
	.end = IRQ_PG13,
	.flags = IORESOURCE_IRQ \| IORESOURCE_IRQ_HIGHLEVEL,
	},
	};

	static struct platform_device net2272_bfin_device = {
	.name = "net2272",
	.id = -1,
	.num_resources = ARRAY_SIZE(net2272_bfin_resources),
	.resource = net2272_bfin_resources,
	};
	#endif

	#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
	static struct mtd_partition cm_partitions[] = {
	{
	.name = "bootloader(nor)",
	.size = 0x40000,
	.offset = 0,
	}, {
	.name = "linux kernel(nor)",
	.size = 0x100000,
	.offset = MTDPART_OFS_APPEND,
	}, {
	.name = "file system(nor)",
	.size = MTDPART_SIZ_FULL,
	.offset = MTDPART_OFS_APPEND,
	}
	};

	static struct physmap_flash_data cm_flash_data = {
	.width = 2,
	.parts = cm_partitions,
	.nr_parts = ARRAY_SIZE(cm_partitions),
	};

	static unsigned cm_flash_gpios[] = { GPIO_PF4 };

	static struct resource cm_flash_resource[] = {
	{
	.name = "cfi_probe",
	.start = 0x20000000,
	.end = 0x201fffff,
	.flags = IORESOURCE_MEM,
	}, {
	.start = (unsigned long)cm_flash_gpios,
	.end = ARRAY_SIZE(cm_flash_gpios),
	.flags = IORESOURCE_IRQ,
	}
	};

	static struct platform_device cm_flash_device = {
	.name = "gpio-addr-flash",
	.id = 0,
	.dev = {
	.platform_data = &cm_flash_data,
	},
	.num_resources = ARRAY_SIZE(cm_flash_resource),
	.resource = cm_flash_resource,
	};
	#endif

	#if IS_ENABLED(CONFIG_SERIAL_BFIN)
	#ifdef CONFIG_SERIAL_BFIN_UART0
	static struct resource bfin_uart0_resources[] = {
	{
	.start = UART0_THR,
	.end = UART0_GCTL+2,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_UART0_TX,
	.end = IRQ_UART0_TX,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_UART0_RX,
	.end = IRQ_UART0_RX,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_UART0_ERROR,
	.end = IRQ_UART0_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = CH_UART0_TX,
	.end = CH_UART0_TX,
	.flags = IORESOURCE_DMA,
	},
	{
	.start = CH_UART0_RX,
	.end = CH_UART0_RX,
	.flags = IORESOURCE_DMA,
	},
	#ifdef CONFIG_BFIN_UART0_CTSRTS
	{
	/*
	* Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
	*/
	.start = -1,
	.end = -1,
	.flags = IORESOURCE_IO,
	},
	{
	/*
	* Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
	*/
	.start = -1,
	.end = -1,
	.flags = IORESOURCE_IO,
	},
	#endif
	};

	static unsigned short bfin_uart0_peripherals[] = {
	P_UART0_TX, P_UART0_RX, 0
	};

	static struct platform_device bfin_uart0_device = {
	.name = "bfin-uart",
	.id = 0,
	.num_resources = ARRAY_SIZE(bfin_uart0_resources),
	.resource = bfin_uart0_resources,
	.dev = {
	.platform_data = &bfin_uart0_peripherals, /* Passed to driver */
	},
	};
	#endif
	#ifdef CONFIG_SERIAL_BFIN_UART1
	static struct resource bfin_uart1_resources[] = {
	{
	.start = UART1_THR,
	.end = UART1_GCTL+2,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_UART1_TX,
	.end = IRQ_UART1_TX,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_UART1_RX,
	.end = IRQ_UART1_RX,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_UART1_ERROR,
	.end = IRQ_UART1_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = CH_UART1_TX,
	.end = CH_UART1_TX,
	.flags = IORESOURCE_DMA,
	},
	{
	.start = CH_UART1_RX,
	.end = CH_UART1_RX,
	.flags = IORESOURCE_DMA,
	},
	#ifdef CONFIG_BFIN_UART1_CTSRTS
	{
	/*
	* Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
	*/
	.start = -1,
	.end = -1,
	.flags = IORESOURCE_IO,
	},
	{
	/*
	* Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
	*/
	.start = -1,
	.end = -1,
	.flags = IORESOURCE_IO,
	},
	#endif
	};

	static unsigned short bfin_uart1_peripherals[] = {
	P_UART1_TX, P_UART1_RX, 0
	};

	static struct platform_device bfin_uart1_device = {
	.name = "bfin-uart",
	.id = 1,
	.num_resources = ARRAY_SIZE(bfin_uart1_resources),
	.resource = bfin_uart1_resources,
	.dev = {
	.platform_data = &bfin_uart1_peripherals, /* Passed to driver */
	},
	};
	#endif
	#endif

	#if IS_ENABLED(CONFIG_BFIN_SIR)
	#ifdef CONFIG_BFIN_SIR0
	static struct resource bfin_sir0_resources[] = {
	{
	.start = 0xFFC00400,
	.end = 0xFFC004FF,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_UART0_RX,
	.end = IRQ_UART0_RX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = CH_UART0_RX,
	.end = CH_UART0_RX+1,
	.flags = IORESOURCE_DMA,
	},
	};
	static struct platform_device bfin_sir0_device = {
	.name = "bfin_sir",
	.id = 0,
	.num_resources = ARRAY_SIZE(bfin_sir0_resources),
	.resource = bfin_sir0_resources,
	};
	#endif
	#ifdef CONFIG_BFIN_SIR1
	static struct resource bfin_sir1_resources[] = {
	{
	.start = 0xFFC02000,
	.end = 0xFFC020FF,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_UART1_RX,
	.end = IRQ_UART1_RX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = CH_UART1_RX,
	.end = CH_UART1_RX+1,
	.flags = IORESOURCE_DMA,
	},
	};
	static struct platform_device bfin_sir1_device = {
	.name = "bfin_sir",
	.id = 1,
	.num_resources = ARRAY_SIZE(bfin_sir1_resources),
	.resource = bfin_sir1_resources,
	};
	#endif
	#endif

	#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
	static const u16 bfin_twi0_pins[] = {P_TWI0_SCL, P_TWI0_SDA, 0};

	static struct resource bfin_twi0_resource[] = {
	[0] = {
	.start = TWI0_REGBASE,
	.end = TWI0_REGBASE,
	.flags = IORESOURCE_MEM,
	},
	[1] = {
	.start = IRQ_TWI,
	.end = IRQ_TWI,
	.flags = IORESOURCE_IRQ,
	},
	};

	static struct platform_device i2c_bfin_twi_device = {
	.name = "i2c-bfin-twi",
	.id = 0,
	.num_resources = ARRAY_SIZE(bfin_twi0_resource),
	.resource = bfin_twi0_resource,
	.dev = {
	.platform_data = &bfin_twi0_pins,
	},
	};
	#endif

	#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT) \
	\|\| IS_ENABLED(CONFIG_BFIN_SPORT)
	unsigned short bfin_sport0_peripherals[] = {
	P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
	P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
	};
	#endif
	#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
	#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
	static struct resource bfin_sport0_uart_resources[] = {
	{
	.start = SPORT0_TCR1,
	.end = SPORT0_MRCS3+4,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_SPORT0_RX,
	.end = IRQ_SPORT0_RX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_SPORT0_ERROR,
	.end = IRQ_SPORT0_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	};

	static struct platform_device bfin_sport0_uart_device = {
	.name = "bfin-sport-uart",
	.id = 0,
	.num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
	.resource = bfin_sport0_uart_resources,
	.dev = {
	.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
	},
	};
	#endif
	#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
	static struct resource bfin_sport1_uart_resources[] = {
	{
	.start = SPORT1_TCR1,
	.end = SPORT1_MRCS3+4,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_SPORT1_RX,
	.end = IRQ_SPORT1_RX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_SPORT1_ERROR,
	.end = IRQ_SPORT1_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	};

	static unsigned short bfin_sport1_peripherals[] = {
	P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
	P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
	};

	static struct platform_device bfin_sport1_uart_device = {
	.name = "bfin-sport-uart",
	.id = 1,
	.num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
	.resource = bfin_sport1_uart_resources,
	.dev = {
	.platform_data = &bfin_sport1_peripherals, /* Passed to driver */
	},
	};
	#endif
	#endif
	#if IS_ENABLED(CONFIG_BFIN_SPORT)
	static struct resource bfin_sport0_resources[] = {
	{
	.start = SPORT0_TCR1,
	.end = SPORT0_MRCS3+4,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = IRQ_SPORT0_RX,
	.end = IRQ_SPORT0_RX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_SPORT0_TX,
	.end = IRQ_SPORT0_TX+1,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = IRQ_SPORT0_ERROR,
	.end = IRQ_SPORT0_ERROR,
	.flags = IORESOURCE_IRQ,
	},
	{
	.start = CH_SPORT0_TX,
	.end = CH_SPORT0_TX,
	.flags = IORESOURCE_DMA,
	},
	{
	.start = CH_SPORT0_RX,
	.end = CH_SPORT0_RX,
	.flags = IORESOURCE_DMA,
	},
	};
	static struct platform_device bfin_sport0_device = {
	.name = "bfin_sport_raw",
	.id = 0,
	.num_resources = ARRAY_SIZE(bfin_sport0_resources),
	.resource = bfin_sport0_resources,
	.dev = {
	.platform_data = &bfin_sport0_peripherals, /* Passed to driver */
	},
	};
	#endif

	#if IS_ENABLED(CONFIG_BFIN_MAC)
	#include <linux/bfin_mac.h>
	static const unsigned short bfin_mac_peripherals[] = P_MII0;

	static struct bfin_phydev_platform_data bfin_phydev_data[] = {
	{
	.addr = 1,
	.irq = IRQ_MAC_PHYINT,
	},
	};

	static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
	.phydev_number = 1,
	.phydev_data = bfin_phydev_data,
	.phy_mode = PHY_INTERFACE_MODE_MII,
	.mac_peripherals = bfin_mac_peripherals,
	};

	static struct platform_device bfin_mii_bus = {
	.name = "bfin_mii_bus",
	.dev = {
	.platform_data = &bfin_mii_bus_data,
	}
	};

	static struct platform_device bfin_mac_device = {
	.name = "bfin_mac",
	.dev = {
	.platform_data = &bfin_mii_bus,
	}
	};
	#endif

	#if IS_ENABLED(CONFIG_PATA_PLATFORM)
	#define PATA_INT IRQ_PF14

	static struct pata_platform_info bfin_pata_platform_data = {
	.ioport_shift = 2,
	.irq_type = IRQF_TRIGGER_HIGH,
	};

	static struct resource bfin_pata_resources[] = {
	{
	.start = 0x2030C000,
	.end = 0x2030C01F,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = 0x2030D018,
	.end = 0x2030D01B,
	.flags = IORESOURCE_MEM,
	},
	{
	.start = PATA_INT,
	.end = PATA_INT,
	.flags = IORESOURCE_IRQ,
	},
	};

	static struct platform_device bfin_pata_device = {
	.name = "pata_platform",
	.id = -1,
	.num_resources = ARRAY_SIZE(bfin_pata_resources),
	.resource = bfin_pata_resources,
	.dev = {
	.platform_data = &bfin_pata_platform_data,
	}
	};
	#endif

	static const unsigned int cclk_vlev_datasheet[] =
	{
	VRPAIR(VLEV_085, 250000000),
	VRPAIR(VLEV_090, 376000000),
	VRPAIR(VLEV_095, 426000000),
	VRPAIR(VLEV_100, 426000000),
	VRPAIR(VLEV_105, 476000000),
	VRPAIR(VLEV_110, 476000000),
	VRPAIR(VLEV_115, 476000000),
	VRPAIR(VLEV_120, 500000000),
	VRPAIR(VLEV_125, 533000000),
	VRPAIR(VLEV_130, 600000000),
	};

	static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
	.tuple_tab = cclk_vlev_datasheet,
	.tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
	.vr_settling_time = 25 /* us */,
	};

	static struct platform_device bfin_dpmc = {
	.name = "bfin dpmc",
	.dev = {
	.platform_data = &bfin_dmpc_vreg_data,
	},
	};

	static struct platform_device *cm_bf537e_devices[] __initdata = {

	&bfin_dpmc,

	#if IS_ENABLED(CONFIG_BFIN_SPORT)
	&bfin_sport0_device,
	#endif

	#if IS_ENABLED(CONFIG_FB_HITACHI_TX09)
	&hitachi_fb_device,
	#endif

	#if IS_ENABLED(CONFIG_RTC_DRV_BFIN)
	&rtc_device,
	#endif

	#if IS_ENABLED(CONFIG_SERIAL_BFIN)
	#ifdef CONFIG_SERIAL_BFIN_UART0
	&bfin_uart0_device,
	#endif
	#ifdef CONFIG_SERIAL_BFIN_UART1
	&bfin_uart1_device,
	#endif
	#endif

	#if IS_ENABLED(CONFIG_BFIN_SIR)
	#ifdef CONFIG_BFIN_SIR0
	&bfin_sir0_device,
	#endif
	#ifdef CONFIG_BFIN_SIR1
	&bfin_sir1_device,
	#endif
	#endif

	#if IS_ENABLED(CONFIG_I2C_BLACKFIN_TWI)
	&i2c_bfin_twi_device,
	#endif

	#if IS_ENABLED(CONFIG_SERIAL_BFIN_SPORT)
	#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
	&bfin_sport0_uart_device,
	#endif
	#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
	&bfin_sport1_uart_device,
	#endif
	#endif

	#if IS_ENABLED(CONFIG_USB_ISP1362_HCD)
	&isp1362_hcd_device,
	#endif

	#if IS_ENABLED(CONFIG_SMC91X)
	&smc91x_device,
	#endif

	#if IS_ENABLED(CONFIG_BFIN_MAC)
	&bfin_mii_bus,
	&bfin_mac_device,
	#endif

	#if IS_ENABLED(CONFIG_USB_NET2272)
	&net2272_bfin_device,
	#endif

	#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
	&bfin_spi0_device,
	#endif

	#if IS_ENABLED(CONFIG_SPI_BFIN_SPORT)
	&bfin_sport_spi0_device,
	&bfin_sport_spi1_device,
	#endif

	#if IS_ENABLED(CONFIG_PATA_PLATFORM)
	&bfin_pata_device,
	#endif

	#if IS_ENABLED(CONFIG_MTD_GPIO_ADDR)
	&cm_flash_device,
	#endif
	};

	static int __init net2272_init(void)
	{
	#if IS_ENABLED(CONFIG_USB_NET2272)
	int ret;

	ret = gpio_request(GPIO_PG14, "net2272");
	if (ret)
	return ret;

	/* Reset USB Chip, PG14 */
	gpio_direction_output(GPIO_PG14, 0);
	mdelay(2);
	gpio_set_value(GPIO_PG14, 1);
	#endif

	return 0;
	}

	static int __init cm_bf537e_init(void)
	{
	printk(KERN_INFO "%s(): registering device resources\n", __func__);
	platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
	#if IS_ENABLED(CONFIG_SPI_BFIN5XX)
	spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
	#endif

	#if IS_ENABLED(CONFIG_PATA_PLATFORM)
	irq_set_status_flags(PATA_INT, IRQ_NOAUTOEN);
	#endif

	if (net2272_init())
	pr_warning("unable to configure net2272; it probably won't work\n");

	return 0;
	}

	arch_initcall(cm_bf537e_init);

	static struct platform_device *cm_bf537e_early_devices[] __initdata = {
	#if defined(CONFIG_SERIAL_BFIN_CONSOLE) \|\| defined(CONFIG_EARLY_PRINTK)
	#ifdef CONFIG_SERIAL_BFIN_UART0
	&bfin_uart0_device,
	#endif
	#ifdef CONFIG_SERIAL_BFIN_UART1
	&bfin_uart1_device,
	#endif
	#endif

	#if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
	#ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
	&bfin_sport0_uart_device,
	#endif
	#ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
	&bfin_sport1_uart_device,
	#endif
	#endif
	};

	void __init native_machine_early_platform_add_devices(void)
	{
	printk(KERN_INFO "register early platform devices\n");
	early_platform_add_devices(cm_bf537e_early_devices,
	ARRAY_SIZE(cm_bf537e_early_devices));
	}

	int bfin_get_ether_addr(char *addr)
	{
	return 1;
	}
	EXPORT_SYMBOL(bfin_get_ether_addr);