| /* |
| * INET An implementation of the TCP/IP protocol suite for the LINUX |
| * operating system. NET is implemented using the BSD Socket |
| * interface as the means of communication with the user level. |
| * |
| * Definitions used by the ARCnet driver. |
| * |
| * Authors: Avery Pennarun and David Woodhouse |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * as published by the Free Software Foundation; either version |
| * 2 of the License, or (at your option) any later version. |
| * |
| */ |
| #ifndef _LINUX_ARCDEVICE_H |
| #define _LINUX_ARCDEVICE_H |
| |
| #include <asm/timex.h> |
| #include <linux/if_arcnet.h> |
| |
| #ifdef __KERNEL__ |
| #include <linux/irqreturn.h> |
| |
| /* |
| * RECON_THRESHOLD is the maximum number of RECON messages to receive |
| * within one minute before printing a "cabling problem" warning. The |
| * default value should be fine. |
| * |
| * After that, a "cabling restored" message will be printed on the next IRQ |
| * if no RECON messages have been received for 10 seconds. |
| * |
| * Do not define RECON_THRESHOLD at all if you want to disable this feature. |
| */ |
| #define RECON_THRESHOLD 30 |
| |
| /* |
| * Define this to the minimum "timeout" value. If a transmit takes longer |
| * than TX_TIMEOUT jiffies, Linux will abort the TX and retry. On a large |
| * network, or one with heavy network traffic, this timeout may need to be |
| * increased. The larger it is, though, the longer it will be between |
| * necessary transmits - don't set this too high. |
| */ |
| #define TX_TIMEOUT (HZ * 200 / 1000) |
| |
| /* Display warnings about the driver being an ALPHA version. */ |
| #undef ALPHA_WARNING |
| |
| /* |
| * Debugging bitflags: each option can be enabled individually. |
| * |
| * Note: only debug flags included in the ARCNET_DEBUG_MAX define will |
| * actually be available. GCC will (at least, GCC 2.7.0 will) notice |
| * lines using a BUGLVL not in ARCNET_DEBUG_MAX and automatically optimize |
| * them out. |
| */ |
| #define D_NORMAL 1 /* important operational info */ |
| #define D_EXTRA 2 /* useful, but non-vital information */ |
| #define D_INIT 4 /* show init/probe messages */ |
| #define D_INIT_REASONS 8 /* show reasons for discarding probes */ |
| #define D_RECON 32 /* print a message whenever token is lost */ |
| #define D_PROTO 64 /* debug auto-protocol support */ |
| /* debug levels below give LOTS of output during normal operation! */ |
| #define D_DURING 128 /* trace operations (including irq's) */ |
| #define D_TX 256 /* show tx packets */ |
| #define D_RX 512 /* show rx packets */ |
| #define D_SKB 1024 /* show skb's */ |
| #define D_SKB_SIZE 2048 /* show skb sizes */ |
| #define D_TIMING 4096 /* show time needed to copy buffers to card */ |
| #define D_DEBUG 8192 /* Very detailed debug line for line */ |
| |
| #ifndef ARCNET_DEBUG_MAX |
| #define ARCNET_DEBUG_MAX (127) /* change to ~0 if you want detailed debugging */ |
| #endif |
| |
| #ifndef ARCNET_DEBUG |
| #define ARCNET_DEBUG (D_NORMAL | D_EXTRA) |
| #endif |
| extern int arcnet_debug; |
| |
| #define BUGLVL(x) ((x) & ARCNET_DEBUG_MAX & arcnet_debug) |
| |
| /* macros to simplify debug checking */ |
| #define arc_printk(x, dev, fmt, ...) \ |
| do { \ |
| if (BUGLVL(x)) { \ |
| if ((x) == D_NORMAL) \ |
| netdev_warn(dev, fmt, ##__VA_ARGS__); \ |
| else if ((x) < D_DURING) \ |
| netdev_info(dev, fmt, ##__VA_ARGS__); \ |
| else \ |
| netdev_dbg(dev, fmt, ##__VA_ARGS__); \ |
| } \ |
| } while (0) |
| |
| #define arc_cont(x, fmt, ...) \ |
| do { \ |
| if (BUGLVL(x)) \ |
| pr_cont(fmt, ##__VA_ARGS__); \ |
| } while (0) |
| |
| /* see how long a function call takes to run, expressed in CPU cycles */ |
| #define TIME(dev, name, bytes, call) \ |
| do { \ |
| if (BUGLVL(D_TIMING)) { \ |
| unsigned long _x, _y; \ |
| _x = get_cycles(); \ |
| call; \ |
| _y = get_cycles(); \ |
| arc_printk(D_TIMING, dev, \ |
| "%s: %d bytes in %lu cycles == %lu Kbytes/100Mcycle\n", \ |
| name, bytes, _y - _x, \ |
| 100000000 / 1024 * bytes / (_y - _x + 1)); \ |
| } else { \ |
| call; \ |
| } \ |
| } while (0) |
| |
| /* |
| * Time needed to reset the card - in ms (milliseconds). This works on my |
| * SMC PC100. I can't find a reference that tells me just how long I |
| * should wait. |
| */ |
| #define RESETtime (300) |
| |
| /* |
| * These are the max/min lengths of packet payload, not including the |
| * arc_hardware header, but definitely including the soft header. |
| * |
| * Note: packet sizes 254, 255, 256 are impossible because of the way |
| * ARCnet registers work That's why RFC1201 defines "exception" packets. |
| * In non-RFC1201 protocols, we have to just tack some extra bytes on the |
| * end. |
| */ |
| #define MTU 253 /* normal packet max size */ |
| #define MinTU 257 /* extended packet min size */ |
| #define XMTU 508 /* extended packet max size */ |
| |
| /* status/interrupt mask bit fields */ |
| #define TXFREEflag 0x01 /* transmitter available */ |
| #define TXACKflag 0x02 /* transmitted msg. ackd */ |
| #define RECONflag 0x04 /* network reconfigured */ |
| #define TESTflag 0x08 /* test flag */ |
| #define EXCNAKflag 0x08 /* excesive nak flag */ |
| #define RESETflag 0x10 /* power-on-reset */ |
| #define RES1flag 0x20 /* reserved - usually set by jumper */ |
| #define RES2flag 0x40 /* reserved - usually set by jumper */ |
| #define NORXflag 0x80 /* receiver inhibited */ |
| |
| /* Flags used for IO-mapped memory operations */ |
| #define AUTOINCflag 0x40 /* Increase location with each access */ |
| #define IOMAPflag 0x02 /* (for 90xx) Use IO mapped memory, not mmap */ |
| #define ENABLE16flag 0x80 /* (for 90xx) Enable 16-bit mode */ |
| |
| /* in the command register, the following bits have these meanings: |
| * 0-2 command |
| * 3-4 page number (for enable rcv/xmt command) |
| * 7 receive broadcasts |
| */ |
| #define NOTXcmd 0x01 /* disable transmitter */ |
| #define NORXcmd 0x02 /* disable receiver */ |
| #define TXcmd 0x03 /* enable transmitter */ |
| #define RXcmd 0x04 /* enable receiver */ |
| #define CONFIGcmd 0x05 /* define configuration */ |
| #define CFLAGScmd 0x06 /* clear flags */ |
| #define TESTcmd 0x07 /* load test flags */ |
| #define STARTIOcmd 0x18 /* start internal operation */ |
| |
| /* flags for "clear flags" command */ |
| #define RESETclear 0x08 /* power-on-reset */ |
| #define CONFIGclear 0x10 /* system reconfigured */ |
| |
| #define EXCNAKclear 0x0E /* Clear and acknowledge the excive nak bit */ |
| |
| /* flags for "load test flags" command */ |
| #define TESTload 0x08 /* test flag (diagnostic) */ |
| |
| /* byte deposited into first address of buffers on reset */ |
| #define TESTvalue 0321 /* that's octal for 0xD1 :) */ |
| |
| /* for "enable receiver" command */ |
| #define RXbcasts 0x80 /* receive broadcasts */ |
| |
| /* flags for "define configuration" command */ |
| #define NORMALconf 0x00 /* 1-249 byte packets */ |
| #define EXTconf 0x08 /* 250-504 byte packets */ |
| |
| /* card feature flags, set during auto-detection. |
| * (currently only used by com20020pci) |
| */ |
| #define ARC_IS_5MBIT 1 /* card default speed is 5MBit */ |
| #define ARC_CAN_10MBIT 2 /* card uses COM20022, supporting 10MBit, |
| but default is 2.5MBit. */ |
| |
| /* information needed to define an encapsulation driver */ |
| struct ArcProto { |
| char suffix; /* a for RFC1201, e for ether-encap, etc. */ |
| int mtu; /* largest possible packet */ |
| int is_ip; /* This is a ip plugin - not a raw thing */ |
| |
| void (*rx)(struct net_device *dev, int bufnum, |
| struct archdr *pkthdr, int length); |
| int (*build_header)(struct sk_buff *skb, struct net_device *dev, |
| unsigned short ethproto, uint8_t daddr); |
| |
| /* these functions return '1' if the skb can now be freed */ |
| int (*prepare_tx)(struct net_device *dev, struct archdr *pkt, |
| int length, int bufnum); |
| int (*continue_tx)(struct net_device *dev, int bufnum); |
| int (*ack_tx)(struct net_device *dev, int acked); |
| }; |
| |
| extern struct ArcProto *arc_proto_map[256], *arc_proto_default, |
| *arc_bcast_proto, *arc_raw_proto; |
| |
| /* |
| * "Incoming" is information needed for each address that could be sending |
| * to us. Mostly for partially-received split packets. |
| */ |
| struct Incoming { |
| struct sk_buff *skb; /* packet data buffer */ |
| __be16 sequence; /* sequence number of assembly */ |
| uint8_t lastpacket, /* number of last packet (from 1) */ |
| numpackets; /* number of packets in split */ |
| }; |
| |
| /* only needed for RFC1201 */ |
| struct Outgoing { |
| struct ArcProto *proto; /* protocol driver that owns this: |
| * if NULL, no packet is pending. |
| */ |
| struct sk_buff *skb; /* buffer from upper levels */ |
| struct archdr *pkt; /* a pointer into the skb */ |
| uint16_t length, /* bytes total */ |
| dataleft, /* bytes left */ |
| segnum, /* segment being sent */ |
| numsegs; /* number of segments */ |
| }; |
| |
| struct arcnet_local { |
| uint8_t config, /* current value of CONFIG register */ |
| timeout, /* Extended timeout for COM20020 */ |
| backplane, /* Backplane flag for COM20020 */ |
| clockp, /* COM20020 clock divider */ |
| clockm, /* COM20020 clock multiplier flag */ |
| setup, /* Contents of setup1 register */ |
| setup2, /* Contents of setup2 register */ |
| intmask; /* current value of INTMASK register */ |
| uint8_t default_proto[256]; /* default encap to use for each host */ |
| int cur_tx, /* buffer used by current transmit, or -1 */ |
| next_tx, /* buffer where a packet is ready to send */ |
| cur_rx; /* current receive buffer */ |
| int lastload_dest, /* can last loaded packet be acked? */ |
| lasttrans_dest; /* can last TX'd packet be acked? */ |
| int timed_out; /* need to process TX timeout and drop packet */ |
| unsigned long last_timeout; /* time of last reported timeout */ |
| char *card_name; /* card ident string */ |
| int card_flags; /* special card features */ |
| |
| /* On preemtive and SMB a lock is needed */ |
| spinlock_t lock; |
| |
| /* |
| * Buffer management: an ARCnet card has 4 x 512-byte buffers, each of |
| * which can be used for either sending or receiving. The new dynamic |
| * buffer management routines use a simple circular queue of available |
| * buffers, and take them as they're needed. This way, we simplify |
| * situations in which we (for example) want to pre-load a transmit |
| * buffer, or start receiving while we copy a received packet to |
| * memory. |
| * |
| * The rules: only the interrupt handler is allowed to _add_ buffers to |
| * the queue; thus, this doesn't require a lock. Both the interrupt |
| * handler and the transmit function will want to _remove_ buffers, so |
| * we need to handle the situation where they try to do it at the same |
| * time. |
| * |
| * If next_buf == first_free_buf, the queue is empty. Since there are |
| * only four possible buffers, the queue should never be full. |
| */ |
| atomic_t buf_lock; |
| int buf_queue[5]; |
| int next_buf, first_free_buf; |
| |
| /* network "reconfiguration" handling */ |
| unsigned long first_recon; /* time of "first" RECON message to count */ |
| unsigned long last_recon; /* time of most recent RECON */ |
| int num_recons; /* number of RECONs between first and last. */ |
| int network_down; /* do we think the network is down? */ |
| |
| int excnak_pending; /* We just got an excesive nak interrupt */ |
| |
| struct { |
| uint16_t sequence; /* sequence number (incs with each packet) */ |
| __be16 aborted_seq; |
| |
| struct Incoming incoming[256]; /* one from each address */ |
| } rfc1201; |
| |
| /* really only used by rfc1201, but we'll pretend it's not */ |
| struct Outgoing outgoing; /* packet currently being sent */ |
| |
| /* hardware-specific functions */ |
| struct { |
| struct module *owner; |
| void (*command)(struct net_device *dev, int cmd); |
| int (*status)(struct net_device *dev); |
| void (*intmask)(struct net_device *dev, int mask); |
| int (*reset)(struct net_device *dev, int really_reset); |
| void (*open)(struct net_device *dev); |
| void (*close)(struct net_device *dev); |
| |
| void (*copy_to_card)(struct net_device *dev, int bufnum, |
| int offset, void *buf, int count); |
| void (*copy_from_card)(struct net_device *dev, int bufnum, |
| int offset, void *buf, int count); |
| } hw; |
| |
| void __iomem *mem_start; /* pointer to ioremap'ed MMIO */ |
| }; |
| |
| #if ARCNET_DEBUG_MAX & D_SKB |
| void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc); |
| #else |
| static inline |
| void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc) |
| { |
| } |
| #endif |
| |
| void arcnet_unregister_proto(struct ArcProto *proto); |
| irqreturn_t arcnet_interrupt(int irq, void *dev_id); |
| struct net_device *alloc_arcdev(const char *name); |
| |
| int arcnet_open(struct net_device *dev); |
| int arcnet_close(struct net_device *dev); |
| netdev_tx_t arcnet_send_packet(struct sk_buff *skb, |
| struct net_device *dev); |
| void arcnet_timeout(struct net_device *dev); |
| |
| /* I/O equivalents */ |
| |
| #ifdef CONFIG_SA1100_CT6001 |
| #define BUS_ALIGN 2 /* 8 bit device on a 16 bit bus - needs padding */ |
| #else |
| #define BUS_ALIGN 1 |
| #endif |
| |
| /* addr and offset allow register like names to define the actual IO address. |
| * A configuration option multiplies the offset for alignment. |
| */ |
| #define arcnet_inb(addr, offset) \ |
| inb((addr) + BUS_ALIGN * (offset)) |
| #define arcnet_outb(value, addr, offset) \ |
| outb(value, (addr) + BUS_ALIGN * (offset)) |
| |
| #define arcnet_insb(addr, offset, buffer, count) \ |
| insb((addr) + BUS_ALIGN * (offset), buffer, count) |
| #define arcnet_outsb(addr, offset, buffer, count) \ |
| outsb((addr) + BUS_ALIGN * (offset), buffer, count) |
| |
| #define arcnet_readb(addr, offset) \ |
| readb((addr) + (offset)) |
| #define arcnet_writeb(value, addr, offset) \ |
| writeb(value, (addr) + (offset)) |
| |
| #endif /* __KERNEL__ */ |
| #endif /* _LINUX_ARCDEVICE_H */ |