include/linux/regulator/consumer.h - kernel/msm-4.19 - Gitiles

 /*
  * consumer.h -- SoC Regulator consumer support.
  *
  * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
  *
  * Author: Liam Girdwood <lrg@slimlogic.co.uk>
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  *
  * Regulator Consumer Interface.
  *
  * A Power Management Regulator framework for SoC based devices.
  * Features:-
  *   o Voltage and current level control.
  *   o Operating mode control.
  *   o Regulator status.
  *   o sysfs entries for showing client devices and status
  *
  * EXPERIMENTAL FEATURES:
  *   Dynamic Regulator operating Mode Switching (DRMS) - allows regulators
  *   to use most efficient operating mode depending upon voltage and load and
  *   is transparent to client drivers.
  *
  *   e.g. Devices x,y,z share regulator r. Device x and y draw 20mA each during
  *   IO and 1mA at idle. Device z draws 100mA when under load and 5mA when
  *   idling. Regulator r has > 90% efficiency in NORMAL mode at loads > 100mA
  *   but this drops rapidly to 60% when below 100mA. Regulator r has > 90%
  *   efficiency in IDLE mode at loads < 10mA. Thus regulator r will operate
  *   in normal mode for loads > 10mA and in IDLE mode for load <= 10mA.
  *
  */

 #ifndef __LINUX_REGULATOR_CONSUMER_H_
 #define __LINUX_REGULATOR_CONSUMER_H_

 #include <linux/device.h>

 /*
  * Regulator operating modes.
  *
  * Regulators can run in a variety of different operating modes depending on
  * output load. This allows further system power savings by selecting the
  * best (and most efficient) regulator mode for a desired load.
  *
  * Most drivers will only care about NORMAL. The modes below are generic and
  * will probably not match the naming convention of your regulator data sheet
  * but should match the use cases in the datasheet.
  *
  * In order of power efficiency (least efficient at top).
  *
  *  Mode       Description
  *  FAST       Regulator can handle fast changes in it's load.
  *             e.g. useful in CPU voltage & frequency scaling where
  *             load can quickly increase with CPU frequency increases.
  *
  *  NORMAL     Normal regulator power supply mode. Most drivers will
  *             use this mode.
  *
  *  IDLE       Regulator runs in a more efficient mode for light
  *             loads. Can be used for devices that have a low power
  *             requirement during periods of inactivity. This mode
  *             may be more noisy than NORMAL and may not be able
  *             to handle fast load switching.
  *
  *  STANDBY    Regulator runs in the most efficient mode for very
  *             light loads. Can be used by devices when they are
  *             in a sleep/standby state. This mode is likely to be
  *             the most noisy and may not be able to handle fast load
  *             switching.
  *
  * NOTE: Most regulators will only support a subset of these modes. Some
  * will only just support NORMAL.
  *
  * These modes can be OR'ed together to make up a mask of valid register modes.
  */

 #define REGULATOR_MODE_FAST			0x1
 #define REGULATOR_MODE_NORMAL			0x2
 #define REGULATOR_MODE_IDLE			0x4
 #define REGULATOR_MODE_STANDBY			0x8

 /*
  * Regulator notifier events.
  *
  * UNDER_VOLTAGE  Regulator output is under voltage.
  * OVER_CURRENT   Regulator output current is too high.
  * REGULATION_OUT Regulator output is out of regulation.
  * FAIL           Regulator output has failed.
  * OVER_TEMP      Regulator over temp.
  * FORCE_DISABLE  Regulator forcibly shut down by software.
  * VOLTAGE_CHANGE Regulator voltage changed.
  * DISABLE        Regulator was disabled.
  *
  * NOTE: These events can be OR'ed together when passed into handler.
  */

 #define REGULATOR_EVENT_UNDER_VOLTAGE		0x01
 #define REGULATOR_EVENT_OVER_CURRENT		0x02
 #define REGULATOR_EVENT_REGULATION_OUT		0x04
 #define REGULATOR_EVENT_FAIL			0x08
 #define REGULATOR_EVENT_OVER_TEMP		0x10
 #define REGULATOR_EVENT_FORCE_DISABLE		0x20
 #define REGULATOR_EVENT_VOLTAGE_CHANGE		0x40
 #define REGULATOR_EVENT_DISABLE 		0x80

 struct regulator;

 /**
  * struct regulator_bulk_data - Data used for bulk regulator operations.
  *
  * @supply:   The name of the supply.  Initialised by the user before
  *            using the bulk regulator APIs.
  * @consumer: The regulator consumer for the supply.  This will be managed
  *            by the bulk API.
  *
  * The regulator APIs provide a series of regulator_bulk_() API calls as
  * a convenience to consumers which require multiple supplies.  This
  * structure is used to manage data for these calls.
  */
 struct regulator_bulk_data {
 	const char *supply;
 	struct regulator *consumer;
 };

 #if defined(CONFIG_REGULATOR)

 /* regulator get and put */
 struct regulator *__must_check regulator_get(struct device *dev,
 					     const char *id);
 struct regulator *__must_check regulator_get_exclusive(struct device *dev,
 						       const char *id);
 void regulator_put(struct regulator *regulator);

 /* regulator output control and status */
 int regulator_enable(struct regulator *regulator);
 int regulator_disable(struct regulator *regulator);
 int regulator_force_disable(struct regulator *regulator);
 int regulator_is_enabled(struct regulator *regulator);

 int regulator_bulk_get(struct device *dev, int num_consumers,
 		       struct regulator_bulk_data *consumers);
 int regulator_bulk_enable(int num_consumers,
 			  struct regulator_bulk_data *consumers);
 int regulator_bulk_disable(int num_consumers,
 			   struct regulator_bulk_data *consumers);
 void regulator_bulk_free(int num_consumers,
 			 struct regulator_bulk_data *consumers);

 int regulator_count_voltages(struct regulator *regulator);
 int regulator_list_voltage(struct regulator *regulator, unsigned selector);
 int regulator_is_supported_voltage(struct regulator *regulator,
 				   int min_uV, int max_uV);
 int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV);
 int regulator_set_voltage_time(struct regulator *regulator,
 			       int old_uV, int new_uV);
 int regulator_get_voltage(struct regulator *regulator);
 int regulator_sync_voltage(struct regulator *regulator);
 int regulator_set_current_limit(struct regulator *regulator,
 			       int min_uA, int max_uA);
 int regulator_get_current_limit(struct regulator *regulator);

 int regulator_set_mode(struct regulator *regulator, unsigned int mode);
 unsigned int regulator_get_mode(struct regulator *regulator);
 int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);

 /* regulator notifier block */
 int regulator_register_notifier(struct regulator *regulator,
 			      struct notifier_block *nb);
 int regulator_unregister_notifier(struct regulator *regulator,
 				struct notifier_block *nb);

 /* driver data - core doesn't touch */
 void *regulator_get_drvdata(struct regulator *regulator);
 void regulator_set_drvdata(struct regulator *regulator, void *data);

 #else

 /*
  * Make sure client drivers will still build on systems with no software
  * controllable voltage or current regulators.
  */
 static inline struct regulator *__must_check regulator_get(struct device *dev,
 	const char *id)
 {
 	/* Nothing except the stubbed out regulator API should be
 	 * looking at the value except to check if it is an error
 	 * value. Drivers are free to handle NULL specifically by
 	 * skipping all regulator API calls, but they don't have to.
 	 * Drivers which don't, should make sure they properly handle
 	 * corner cases of the API, such as regulator_get_voltage()
 	 * returning 0.
 	 */
 	return NULL;
 }
 static inline void regulator_put(struct regulator *regulator)
 {
 }

 static inline int regulator_enable(struct regulator *regulator)
 {
 	return 0;
 }

 static inline int regulator_disable(struct regulator *regulator)
 {
 	return 0;
 }

 static inline int regulator_is_enabled(struct regulator *regulator)
 {
 	return 1;
 }

 static inline int regulator_bulk_get(struct device *dev,
 				     int num_consumers,
 				     struct regulator_bulk_data *consumers)
 {
 	return 0;
 }

 static inline int regulator_bulk_enable(int num_consumers,
 					struct regulator_bulk_data *consumers)
 {
 	return 0;
 }

 static inline int regulator_bulk_disable(int num_consumers,
 					 struct regulator_bulk_data *consumers)
 {
 	return 0;
 }

 static inline void regulator_bulk_free(int num_consumers,
 				       struct regulator_bulk_data *consumers)
 {
 }

 static inline int regulator_set_voltage(struct regulator *regulator,
 					int min_uV, int max_uV)
 {
 	return 0;
 }

 static inline int regulator_get_voltage(struct regulator *regulator)
 {
 	return 0;
 }

 static inline int regulator_set_current_limit(struct regulator *regulator,
 					     int min_uA, int max_uA)
 {
 	return 0;
 }

 static inline int regulator_get_current_limit(struct regulator *regulator)
 {
 	return 0;
 }

 static inline int regulator_set_mode(struct regulator *regulator,
 	unsigned int mode)
 {
 	return 0;
 }

 static inline unsigned int regulator_get_mode(struct regulator *regulator)
 {
 	return REGULATOR_MODE_NORMAL;
 }

 static inline int regulator_set_optimum_mode(struct regulator *regulator,
 					int load_uA)
 {
 	return REGULATOR_MODE_NORMAL;
 }

 static inline int regulator_register_notifier(struct regulator *regulator,
 			      struct notifier_block *nb)
 {
 	return 0;
 }

 static inline int regulator_unregister_notifier(struct regulator *regulator,
 				struct notifier_block *nb)
 {
 	return 0;
 }

 static inline void *regulator_get_drvdata(struct regulator *regulator)
 {
 	return NULL;
 }

 static inline void regulator_set_drvdata(struct regulator *regulator,
 	void *data)
 {
 }

 #endif

 #endif
	/*
	* consumer.h -- SoC Regulator consumer support.
	*
	* Copyright (C) 2007, 2008 Wolfson Microelectronics PLC.
	*
	* Author: Liam Girdwood <lrg@slimlogic.co.uk>
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License version 2 as
	* published by the Free Software Foundation.
	*
	* Regulator Consumer Interface.
	*
	* A Power Management Regulator framework for SoC based devices.
	* Features:-
	* o Voltage and current level control.
	* o Operating mode control.
	* o Regulator status.
	* o sysfs entries for showing client devices and status
	*
	* EXPERIMENTAL FEATURES:
	* Dynamic Regulator operating Mode Switching (DRMS) - allows regulators
	* to use most efficient operating mode depending upon voltage and load and
	* is transparent to client drivers.
	*
	* e.g. Devices x,y,z share regulator r. Device x and y draw 20mA each during
	* IO and 1mA at idle. Device z draws 100mA when under load and 5mA when
	* idling. Regulator r has > 90% efficiency in NORMAL mode at loads > 100mA
	* but this drops rapidly to 60% when below 100mA. Regulator r has > 90%
	* efficiency in IDLE mode at loads < 10mA. Thus regulator r will operate
	* in normal mode for loads > 10mA and in IDLE mode for load <= 10mA.
	*
	*/

	#ifndef __LINUX_REGULATOR_CONSUMER_H_
	#define __LINUX_REGULATOR_CONSUMER_H_

	#include <linux/device.h>

	/*
	* Regulator operating modes.
	*
	* Regulators can run in a variety of different operating modes depending on
	* output load. This allows further system power savings by selecting the
	* best (and most efficient) regulator mode for a desired load.
	*
	* Most drivers will only care about NORMAL. The modes below are generic and
	* will probably not match the naming convention of your regulator data sheet
	* but should match the use cases in the datasheet.
	*
	* In order of power efficiency (least efficient at top).
	*
	* Mode Description
	* FAST Regulator can handle fast changes in it's load.
	* e.g. useful in CPU voltage & frequency scaling where
	* load can quickly increase with CPU frequency increases.
	*
	* NORMAL Normal regulator power supply mode. Most drivers will
	* use this mode.
	*
	* IDLE Regulator runs in a more efficient mode for light
	* loads. Can be used for devices that have a low power
	* requirement during periods of inactivity. This mode
	* may be more noisy than NORMAL and may not be able
	* to handle fast load switching.
	*
	* STANDBY Regulator runs in the most efficient mode for very
	* light loads. Can be used by devices when they are
	* in a sleep/standby state. This mode is likely to be
	* the most noisy and may not be able to handle fast load
	* switching.
	*
	* NOTE: Most regulators will only support a subset of these modes. Some
	* will only just support NORMAL.
	*
	* These modes can be OR'ed together to make up a mask of valid register modes.
	*/

	#define REGULATOR_MODE_FAST 0x1
	#define REGULATOR_MODE_NORMAL 0x2
	#define REGULATOR_MODE_IDLE 0x4
	#define REGULATOR_MODE_STANDBY 0x8

	/*
	* Regulator notifier events.
	*
	* UNDER_VOLTAGE Regulator output is under voltage.
	* OVER_CURRENT Regulator output current is too high.
	* REGULATION_OUT Regulator output is out of regulation.
	* FAIL Regulator output has failed.
	* OVER_TEMP Regulator over temp.
	* FORCE_DISABLE Regulator forcibly shut down by software.
	* VOLTAGE_CHANGE Regulator voltage changed.
	* DISABLE Regulator was disabled.
	*
	* NOTE: These events can be OR'ed together when passed into handler.
	*/

	#define REGULATOR_EVENT_UNDER_VOLTAGE 0x01
	#define REGULATOR_EVENT_OVER_CURRENT 0x02
	#define REGULATOR_EVENT_REGULATION_OUT 0x04
	#define REGULATOR_EVENT_FAIL 0x08
	#define REGULATOR_EVENT_OVER_TEMP 0x10
	#define REGULATOR_EVENT_FORCE_DISABLE 0x20
	#define REGULATOR_EVENT_VOLTAGE_CHANGE 0x40
	#define REGULATOR_EVENT_DISABLE 0x80

	struct regulator;

	/**
	* struct regulator_bulk_data - Data used for bulk regulator operations.
	*
	* @supply: The name of the supply. Initialised by the user before
	* using the bulk regulator APIs.
	* @consumer: The regulator consumer for the supply. This will be managed
	* by the bulk API.
	*
	* The regulator APIs provide a series of regulator_bulk_() API calls as
	* a convenience to consumers which require multiple supplies. This
	* structure is used to manage data for these calls.
	*/
	struct regulator_bulk_data {
	const char *supply;
	struct regulator *consumer;
	};

	#if defined(CONFIG_REGULATOR)

	/* regulator get and put */
	struct regulator __must_check regulator_get(struct device dev,
	const char *id);
	struct regulator __must_check regulator_get_exclusive(struct device dev,
	const char *id);
	void regulator_put(struct regulator *regulator);

	/* regulator output control and status */
	int regulator_enable(struct regulator *regulator);
	int regulator_disable(struct regulator *regulator);
	int regulator_force_disable(struct regulator *regulator);
	int regulator_is_enabled(struct regulator *regulator);

	int regulator_bulk_get(struct device *dev, int num_consumers,
	struct regulator_bulk_data *consumers);
	int regulator_bulk_enable(int num_consumers,
	struct regulator_bulk_data *consumers);
	int regulator_bulk_disable(int num_consumers,
	struct regulator_bulk_data *consumers);
	void regulator_bulk_free(int num_consumers,
	struct regulator_bulk_data *consumers);

	int regulator_count_voltages(struct regulator *regulator);
	int regulator_list_voltage(struct regulator *regulator, unsigned selector);
	int regulator_is_supported_voltage(struct regulator *regulator,
	int min_uV, int max_uV);
	int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV);
	int regulator_set_voltage_time(struct regulator *regulator,
	int old_uV, int new_uV);
	int regulator_get_voltage(struct regulator *regulator);
	int regulator_sync_voltage(struct regulator *regulator);
	int regulator_set_current_limit(struct regulator *regulator,
	int min_uA, int max_uA);
	int regulator_get_current_limit(struct regulator *regulator);

	int regulator_set_mode(struct regulator *regulator, unsigned int mode);
	unsigned int regulator_get_mode(struct regulator *regulator);
	int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);

	/* regulator notifier block */
	int regulator_register_notifier(struct regulator *regulator,
	struct notifier_block *nb);
	int regulator_unregister_notifier(struct regulator *regulator,
	struct notifier_block *nb);

	/* driver data - core doesn't touch */
	void regulator_get_drvdata(struct regulator regulator);
	void regulator_set_drvdata(struct regulator regulator, void data);

	#else

	/*
	* Make sure client drivers will still build on systems with no software
	* controllable voltage or current regulators.
	*/
	static inline struct regulator __must_check regulator_get(struct device dev,
	const char *id)
	{
	/* Nothing except the stubbed out regulator API should be
	* looking at the value except to check if it is an error
	* value. Drivers are free to handle NULL specifically by
	* skipping all regulator API calls, but they don't have to.
	* Drivers which don't, should make sure they properly handle
	* corner cases of the API, such as regulator_get_voltage()
	* returning 0.
	*/
	return NULL;
	}
	static inline void regulator_put(struct regulator *regulator)
	{
	}

	static inline int regulator_enable(struct regulator *regulator)
	{
	return 0;
	}

	static inline int regulator_disable(struct regulator *regulator)
	{
	return 0;
	}

	static inline int regulator_is_enabled(struct regulator *regulator)
	{
	return 1;
	}

	static inline int regulator_bulk_get(struct device *dev,
	int num_consumers,
	struct regulator_bulk_data *consumers)
	{
	return 0;
	}

	static inline int regulator_bulk_enable(int num_consumers,
	struct regulator_bulk_data *consumers)
	{
	return 0;
	}

	static inline int regulator_bulk_disable(int num_consumers,
	struct regulator_bulk_data *consumers)
	{
	return 0;
	}

	static inline void regulator_bulk_free(int num_consumers,
	struct regulator_bulk_data *consumers)
	{
	}

	static inline int regulator_set_voltage(struct regulator *regulator,
	int min_uV, int max_uV)
	{
	return 0;
	}

	static inline int regulator_get_voltage(struct regulator *regulator)
	{
	return 0;
	}

	static inline int regulator_set_current_limit(struct regulator *regulator,
	int min_uA, int max_uA)
	{
	return 0;
	}

	static inline int regulator_get_current_limit(struct regulator *regulator)
	{
	return 0;
	}

	static inline int regulator_set_mode(struct regulator *regulator,
	unsigned int mode)
	{
	return 0;
	}

	static inline unsigned int regulator_get_mode(struct regulator *regulator)
	{
	return REGULATOR_MODE_NORMAL;
	}

	static inline int regulator_set_optimum_mode(struct regulator *regulator,
	int load_uA)
	{
	return REGULATOR_MODE_NORMAL;
	}

	static inline int regulator_register_notifier(struct regulator *regulator,
	struct notifier_block *nb)
	{
	return 0;
	}

	static inline int regulator_unregister_notifier(struct regulator *regulator,
	struct notifier_block *nb)
	{
	return 0;
	}

	static inline void regulator_get_drvdata(struct regulator regulator)
	{
	return NULL;
	}

	static inline void regulator_set_drvdata(struct regulator *regulator,
	void *data)
	{
	}

	#endif

	#endif