Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* vi: ts=8 sw=8 |
| 2 | * |
| 3 | * TI 3410/5052 USB Serial Driver Header |
| 4 | * |
| 5 | * Copyright (C) 2004 Texas Instruments |
| 6 | * |
| 7 | * This driver is based on the Linux io_ti driver, which is |
| 8 | * Copyright (C) 2000-2002 Inside Out Networks |
| 9 | * Copyright (C) 2001-2002 Greg Kroah-Hartman |
| 10 | * |
| 11 | * This program is free software; you can redistribute it and/or modify |
| 12 | * it under the terms of the GNU General Public License as published by |
| 13 | * the Free Software Foundation; either version 2 of the License, or |
| 14 | * (at your option) any later version. |
| 15 | * |
| 16 | * For questions or problems with this driver, contact Texas Instruments |
| 17 | * technical support, or Al Borchers <alborchers@steinerpoint.com>, or |
| 18 | * Peter Berger <pberger@brimson.com>. |
| 19 | */ |
| 20 | |
| 21 | #ifndef _TI_3410_5052_H_ |
| 22 | #define _TI_3410_5052_H_ |
| 23 | |
| 24 | /* Configuration ids */ |
| 25 | #define TI_BOOT_CONFIG 1 |
| 26 | #define TI_ACTIVE_CONFIG 2 |
| 27 | |
| 28 | /* Vendor and product ids */ |
| 29 | #define TI_VENDOR_ID 0x0451 |
| 30 | #define TI_3410_PRODUCT_ID 0x3410 |
| 31 | #define TI_5052_BOOT_PRODUCT_ID 0x5052 /* no EEPROM, no firmware */ |
| 32 | #define TI_5152_BOOT_PRODUCT_ID 0x5152 /* no EEPROM, no firmware */ |
| 33 | #define TI_5052_EEPROM_PRODUCT_ID 0x505A /* EEPROM, no firmware */ |
| 34 | #define TI_5052_FIRMWARE_PRODUCT_ID 0x505F /* firmware is running */ |
| 35 | |
| 36 | /* Commands */ |
| 37 | #define TI_GET_VERSION 0x01 |
| 38 | #define TI_GET_PORT_STATUS 0x02 |
| 39 | #define TI_GET_PORT_DEV_INFO 0x03 |
| 40 | #define TI_GET_CONFIG 0x04 |
| 41 | #define TI_SET_CONFIG 0x05 |
| 42 | #define TI_OPEN_PORT 0x06 |
| 43 | #define TI_CLOSE_PORT 0x07 |
| 44 | #define TI_START_PORT 0x08 |
| 45 | #define TI_STOP_PORT 0x09 |
| 46 | #define TI_TEST_PORT 0x0A |
| 47 | #define TI_PURGE_PORT 0x0B |
| 48 | #define TI_RESET_EXT_DEVICE 0x0C |
| 49 | #define TI_WRITE_DATA 0x80 |
| 50 | #define TI_READ_DATA 0x81 |
| 51 | #define TI_REQ_TYPE_CLASS 0x82 |
| 52 | |
| 53 | /* Module identifiers */ |
| 54 | #define TI_I2C_PORT 0x01 |
| 55 | #define TI_IEEE1284_PORT 0x02 |
| 56 | #define TI_UART1_PORT 0x03 |
| 57 | #define TI_UART2_PORT 0x04 |
| 58 | #define TI_RAM_PORT 0x05 |
| 59 | |
| 60 | /* Modem status */ |
| 61 | #define TI_MSR_DELTA_CTS 0x01 |
| 62 | #define TI_MSR_DELTA_DSR 0x02 |
| 63 | #define TI_MSR_DELTA_RI 0x04 |
| 64 | #define TI_MSR_DELTA_CD 0x08 |
| 65 | #define TI_MSR_CTS 0x10 |
| 66 | #define TI_MSR_DSR 0x20 |
| 67 | #define TI_MSR_RI 0x40 |
| 68 | #define TI_MSR_CD 0x80 |
| 69 | #define TI_MSR_DELTA_MASK 0x0F |
| 70 | #define TI_MSR_MASK 0xF0 |
| 71 | |
| 72 | /* Line status */ |
| 73 | #define TI_LSR_OVERRUN_ERROR 0x01 |
| 74 | #define TI_LSR_PARITY_ERROR 0x02 |
| 75 | #define TI_LSR_FRAMING_ERROR 0x04 |
| 76 | #define TI_LSR_BREAK 0x08 |
| 77 | #define TI_LSR_ERROR 0x0F |
| 78 | #define TI_LSR_RX_FULL 0x10 |
| 79 | #define TI_LSR_TX_EMPTY 0x20 |
| 80 | |
| 81 | /* Line control */ |
| 82 | #define TI_LCR_BREAK 0x40 |
| 83 | |
| 84 | /* Modem control */ |
| 85 | #define TI_MCR_LOOP 0x04 |
| 86 | #define TI_MCR_DTR 0x10 |
| 87 | #define TI_MCR_RTS 0x20 |
| 88 | |
| 89 | /* Mask settings */ |
| 90 | #define TI_UART_ENABLE_RTS_IN 0x0001 |
| 91 | #define TI_UART_DISABLE_RTS 0x0002 |
| 92 | #define TI_UART_ENABLE_PARITY_CHECKING 0x0008 |
| 93 | #define TI_UART_ENABLE_DSR_OUT 0x0010 |
| 94 | #define TI_UART_ENABLE_CTS_OUT 0x0020 |
| 95 | #define TI_UART_ENABLE_X_OUT 0x0040 |
| 96 | #define TI_UART_ENABLE_XA_OUT 0x0080 |
| 97 | #define TI_UART_ENABLE_X_IN 0x0100 |
| 98 | #define TI_UART_ENABLE_DTR_IN 0x0800 |
| 99 | #define TI_UART_DISABLE_DTR 0x1000 |
| 100 | #define TI_UART_ENABLE_MS_INTS 0x2000 |
| 101 | #define TI_UART_ENABLE_AUTO_START_DMA 0x4000 |
| 102 | |
| 103 | /* Parity */ |
| 104 | #define TI_UART_NO_PARITY 0x00 |
| 105 | #define TI_UART_ODD_PARITY 0x01 |
| 106 | #define TI_UART_EVEN_PARITY 0x02 |
| 107 | #define TI_UART_MARK_PARITY 0x03 |
| 108 | #define TI_UART_SPACE_PARITY 0x04 |
| 109 | |
| 110 | /* Stop bits */ |
| 111 | #define TI_UART_1_STOP_BITS 0x00 |
| 112 | #define TI_UART_1_5_STOP_BITS 0x01 |
| 113 | #define TI_UART_2_STOP_BITS 0x02 |
| 114 | |
| 115 | /* Bits per character */ |
| 116 | #define TI_UART_5_DATA_BITS 0x00 |
| 117 | #define TI_UART_6_DATA_BITS 0x01 |
| 118 | #define TI_UART_7_DATA_BITS 0x02 |
| 119 | #define TI_UART_8_DATA_BITS 0x03 |
| 120 | |
| 121 | /* 232/485 modes */ |
| 122 | #define TI_UART_232 0x00 |
| 123 | #define TI_UART_485_RECEIVER_DISABLED 0x01 |
| 124 | #define TI_UART_485_RECEIVER_ENABLED 0x02 |
| 125 | |
| 126 | /* Pipe transfer mode and timeout */ |
| 127 | #define TI_PIPE_MODE_CONTINOUS 0x01 |
| 128 | #define TI_PIPE_MODE_MASK 0x03 |
| 129 | #define TI_PIPE_TIMEOUT_MASK 0x7C |
| 130 | #define TI_PIPE_TIMEOUT_ENABLE 0x80 |
| 131 | |
| 132 | /* Config struct */ |
| 133 | struct ti_uart_config { |
| 134 | __u16 wBaudRate; |
| 135 | __u16 wFlags; |
| 136 | __u8 bDataBits; |
| 137 | __u8 bParity; |
| 138 | __u8 bStopBits; |
| 139 | char cXon; |
| 140 | char cXoff; |
| 141 | __u8 bUartMode; |
| 142 | } __attribute__((packed)); |
| 143 | |
| 144 | /* Get port status */ |
| 145 | struct ti_port_status { |
| 146 | __u8 bCmdCode; |
| 147 | __u8 bModuleId; |
| 148 | __u8 bErrorCode; |
| 149 | __u8 bMSR; |
| 150 | __u8 bLSR; |
| 151 | } __attribute__((packed)); |
| 152 | |
| 153 | /* Purge modes */ |
| 154 | #define TI_PURGE_OUTPUT 0x00 |
| 155 | #define TI_PURGE_INPUT 0x80 |
| 156 | |
| 157 | /* Read/Write data */ |
| 158 | #define TI_RW_DATA_ADDR_SFR 0x10 |
| 159 | #define TI_RW_DATA_ADDR_IDATA 0x20 |
| 160 | #define TI_RW_DATA_ADDR_XDATA 0x30 |
| 161 | #define TI_RW_DATA_ADDR_CODE 0x40 |
| 162 | #define TI_RW_DATA_ADDR_GPIO 0x50 |
| 163 | #define TI_RW_DATA_ADDR_I2C 0x60 |
| 164 | #define TI_RW_DATA_ADDR_FLASH 0x70 |
| 165 | #define TI_RW_DATA_ADDR_DSP 0x80 |
| 166 | |
| 167 | #define TI_RW_DATA_UNSPECIFIED 0x00 |
| 168 | #define TI_RW_DATA_BYTE 0x01 |
| 169 | #define TI_RW_DATA_WORD 0x02 |
| 170 | #define TI_RW_DATA_DOUBLE_WORD 0x04 |
| 171 | |
| 172 | struct ti_write_data_bytes { |
| 173 | __u8 bAddrType; |
| 174 | __u8 bDataType; |
| 175 | __u8 bDataCounter; |
| 176 | __be16 wBaseAddrHi; |
| 177 | __be16 wBaseAddrLo; |
| 178 | __u8 bData[0]; |
| 179 | } __attribute__((packed)); |
| 180 | |
| 181 | struct ti_read_data_request { |
| 182 | __u8 bAddrType; |
| 183 | __u8 bDataType; |
| 184 | __u8 bDataCounter; |
| 185 | __be16 wBaseAddrHi; |
| 186 | __be16 wBaseAddrLo; |
| 187 | } __attribute__((packed)); |
| 188 | |
| 189 | struct ti_read_data_bytes { |
| 190 | __u8 bCmdCode; |
| 191 | __u8 bModuleId; |
| 192 | __u8 bErrorCode; |
| 193 | __u8 bData[0]; |
| 194 | } __attribute__((packed)); |
| 195 | |
| 196 | /* Interrupt struct */ |
| 197 | struct ti_interrupt { |
| 198 | __u8 bICode; |
| 199 | __u8 bIInfo; |
| 200 | } __attribute__((packed)); |
| 201 | |
| 202 | /* Interrupt codes */ |
| 203 | #define TI_GET_PORT_FROM_CODE(c) (((c) >> 4) - 3) |
| 204 | #define TI_GET_FUNC_FROM_CODE(c) ((c) & 0x0f) |
| 205 | #define TI_CODE_HARDWARE_ERROR 0xFF |
| 206 | #define TI_CODE_DATA_ERROR 0x03 |
| 207 | #define TI_CODE_MODEM_STATUS 0x04 |
| 208 | |
| 209 | /* Download firmware max packet size */ |
| 210 | #define TI_DOWNLOAD_MAX_PACKET_SIZE 64 |
| 211 | |
| 212 | /* Firmware image header */ |
| 213 | struct ti_firmware_header { |
| 214 | __le16 wLength; |
| 215 | __u8 bCheckSum; |
| 216 | } __attribute__((packed)); |
| 217 | |
| 218 | /* UART addresses */ |
| 219 | #define TI_UART1_BASE_ADDR 0xFFA0 /* UART 1 base address */ |
| 220 | #define TI_UART2_BASE_ADDR 0xFFB0 /* UART 2 base address */ |
| 221 | #define TI_UART_OFFSET_LCR 0x0002 /* UART MCR register offset */ |
| 222 | #define TI_UART_OFFSET_MCR 0x0004 /* UART MCR register offset */ |
| 223 | |
| 224 | #endif /* _TI_3410_5052_H_ */ |