Ira W. Snyder | bd35813 | 2010-04-07 09:43:00 +0200 | [diff] [blame] | 1 | /* |
| 2 | * Janz CMOD-IO MODULbus Carrier Board PCI Driver |
| 3 | * |
| 4 | * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> |
| 5 | * |
| 6 | * Lots of inspiration and code was copied from drivers/mfd/sm501.c |
| 7 | * |
| 8 | * This program is free software; you can redistribute it and/or modify it |
| 9 | * under the terms of the GNU General Public License as published by the |
| 10 | * Free Software Foundation; either version 2 of the License, or (at your |
| 11 | * option) any later version. |
| 12 | */ |
| 13 | |
| 14 | #include <linux/kernel.h> |
| 15 | #include <linux/module.h> |
| 16 | #include <linux/init.h> |
| 17 | #include <linux/pci.h> |
| 18 | #include <linux/interrupt.h> |
| 19 | #include <linux/delay.h> |
| 20 | #include <linux/platform_device.h> |
David Miller | 8102bad | 2010-08-04 22:57:14 -0700 | [diff] [blame] | 21 | #include <linux/slab.h> |
Ira W. Snyder | bd35813 | 2010-04-07 09:43:00 +0200 | [diff] [blame] | 22 | #include <linux/mfd/core.h> |
| 23 | |
| 24 | #include <linux/mfd/janz.h> |
| 25 | |
| 26 | #define DRV_NAME "janz-cmodio" |
| 27 | |
| 28 | /* Size of each MODULbus module in PCI BAR4 */ |
| 29 | #define CMODIO_MODULBUS_SIZE 0x200 |
| 30 | |
| 31 | /* Maximum number of MODULbus modules on a CMOD-IO carrier board */ |
| 32 | #define CMODIO_MAX_MODULES 4 |
| 33 | |
| 34 | /* Module Parameters */ |
| 35 | static unsigned int num_modules = CMODIO_MAX_MODULES; |
| 36 | static unsigned char *modules[CMODIO_MAX_MODULES] = { |
| 37 | "empty", "empty", "empty", "empty", |
| 38 | }; |
| 39 | |
| 40 | module_param_array(modules, charp, &num_modules, S_IRUGO); |
| 41 | MODULE_PARM_DESC(modules, "MODULbus modules attached to the carrier board"); |
| 42 | |
| 43 | /* Unique Device Id */ |
| 44 | static unsigned int cmodio_id; |
| 45 | |
| 46 | struct cmodio_device { |
| 47 | /* Parent PCI device */ |
| 48 | struct pci_dev *pdev; |
| 49 | |
| 50 | /* PLX control registers */ |
| 51 | struct janz_cmodio_onboard_regs __iomem *ctrl; |
| 52 | |
| 53 | /* hex switch position */ |
| 54 | u8 hex; |
| 55 | |
| 56 | /* mfd-core API */ |
| 57 | struct mfd_cell cells[CMODIO_MAX_MODULES]; |
| 58 | struct resource resources[3 * CMODIO_MAX_MODULES]; |
| 59 | struct janz_platform_data pdata[CMODIO_MAX_MODULES]; |
| 60 | }; |
| 61 | |
| 62 | /* |
| 63 | * Subdevices using the mfd-core API |
| 64 | */ |
| 65 | |
| 66 | static int __devinit cmodio_setup_subdevice(struct cmodio_device *priv, |
| 67 | char *name, unsigned int devno, |
| 68 | unsigned int modno) |
| 69 | { |
| 70 | struct janz_platform_data *pdata; |
| 71 | struct mfd_cell *cell; |
| 72 | struct resource *res; |
| 73 | struct pci_dev *pci; |
| 74 | |
| 75 | pci = priv->pdev; |
| 76 | cell = &priv->cells[devno]; |
| 77 | res = &priv->resources[devno * 3]; |
| 78 | pdata = &priv->pdata[devno]; |
| 79 | |
| 80 | cell->name = name; |
| 81 | cell->resources = res; |
| 82 | cell->num_resources = 3; |
| 83 | |
| 84 | /* Setup the subdevice ID -- must be unique */ |
| 85 | cell->id = cmodio_id++; |
| 86 | |
| 87 | /* Add platform data */ |
| 88 | pdata->modno = modno; |
| 89 | cell->platform_data = pdata; |
| 90 | cell->data_size = sizeof(*pdata); |
| 91 | |
| 92 | /* MODULbus registers -- PCI BAR3 is big-endian MODULbus access */ |
| 93 | res->flags = IORESOURCE_MEM; |
| 94 | res->parent = &pci->resource[3]; |
| 95 | res->start = pci->resource[3].start + (CMODIO_MODULBUS_SIZE * modno); |
| 96 | res->end = res->start + CMODIO_MODULBUS_SIZE - 1; |
| 97 | res++; |
| 98 | |
| 99 | /* PLX Control Registers -- PCI BAR4 is interrupt and other registers */ |
| 100 | res->flags = IORESOURCE_MEM; |
| 101 | res->parent = &pci->resource[4]; |
| 102 | res->start = pci->resource[4].start; |
| 103 | res->end = pci->resource[4].end; |
| 104 | res++; |
| 105 | |
| 106 | /* |
| 107 | * IRQ |
| 108 | * |
| 109 | * The start and end fields are used as an offset to the irq_base |
| 110 | * parameter passed into the mfd_add_devices() function call. All |
| 111 | * devices share the same IRQ. |
| 112 | */ |
| 113 | res->flags = IORESOURCE_IRQ; |
| 114 | res->parent = NULL; |
| 115 | res->start = 0; |
| 116 | res->end = 0; |
| 117 | res++; |
| 118 | |
| 119 | return 0; |
| 120 | } |
| 121 | |
| 122 | /* Probe each submodule using kernel parameters */ |
| 123 | static int __devinit cmodio_probe_submodules(struct cmodio_device *priv) |
| 124 | { |
| 125 | struct pci_dev *pdev = priv->pdev; |
| 126 | unsigned int num_probed = 0; |
| 127 | char *name; |
| 128 | int i; |
| 129 | |
| 130 | for (i = 0; i < num_modules; i++) { |
| 131 | name = modules[i]; |
| 132 | if (!strcmp(name, "") || !strcmp(name, "empty")) |
| 133 | continue; |
| 134 | |
| 135 | dev_dbg(&priv->pdev->dev, "MODULbus %d: name %s\n", i, name); |
| 136 | cmodio_setup_subdevice(priv, name, num_probed, i); |
| 137 | num_probed++; |
| 138 | } |
| 139 | |
| 140 | /* print an error message if no modules were probed */ |
| 141 | if (num_probed == 0) { |
| 142 | dev_err(&priv->pdev->dev, "no MODULbus modules specified, " |
| 143 | "please set the ``modules'' kernel " |
| 144 | "parameter according to your " |
| 145 | "hardware configuration\n"); |
| 146 | return -ENODEV; |
| 147 | } |
| 148 | |
| 149 | return mfd_add_devices(&pdev->dev, 0, priv->cells, |
| 150 | num_probed, NULL, pdev->irq); |
| 151 | } |
| 152 | |
| 153 | /* |
| 154 | * SYSFS Attributes |
| 155 | */ |
| 156 | |
| 157 | static ssize_t mbus_show(struct device *dev, struct device_attribute *attr, |
| 158 | char *buf) |
| 159 | { |
| 160 | struct cmodio_device *priv = dev_get_drvdata(dev); |
| 161 | |
| 162 | return snprintf(buf, PAGE_SIZE, "%x\n", priv->hex); |
| 163 | } |
| 164 | |
| 165 | static DEVICE_ATTR(modulbus_number, S_IRUGO, mbus_show, NULL); |
| 166 | |
| 167 | static struct attribute *cmodio_sysfs_attrs[] = { |
| 168 | &dev_attr_modulbus_number.attr, |
| 169 | NULL, |
| 170 | }; |
| 171 | |
| 172 | static const struct attribute_group cmodio_sysfs_attr_group = { |
| 173 | .attrs = cmodio_sysfs_attrs, |
| 174 | }; |
| 175 | |
| 176 | /* |
| 177 | * PCI Driver |
| 178 | */ |
| 179 | |
| 180 | static int __devinit cmodio_pci_probe(struct pci_dev *dev, |
| 181 | const struct pci_device_id *id) |
| 182 | { |
| 183 | struct cmodio_device *priv; |
| 184 | int ret; |
| 185 | |
| 186 | priv = kzalloc(sizeof(*priv), GFP_KERNEL); |
| 187 | if (!priv) { |
| 188 | dev_err(&dev->dev, "unable to allocate private data\n"); |
| 189 | ret = -ENOMEM; |
| 190 | goto out_return; |
| 191 | } |
| 192 | |
| 193 | pci_set_drvdata(dev, priv); |
| 194 | priv->pdev = dev; |
| 195 | |
| 196 | /* Hardware Initialization */ |
| 197 | ret = pci_enable_device(dev); |
| 198 | if (ret) { |
| 199 | dev_err(&dev->dev, "unable to enable device\n"); |
| 200 | goto out_free_priv; |
| 201 | } |
| 202 | |
| 203 | pci_set_master(dev); |
| 204 | ret = pci_request_regions(dev, DRV_NAME); |
| 205 | if (ret) { |
| 206 | dev_err(&dev->dev, "unable to request regions\n"); |
| 207 | goto out_pci_disable_device; |
| 208 | } |
| 209 | |
| 210 | /* Onboard configuration registers */ |
| 211 | priv->ctrl = pci_ioremap_bar(dev, 4); |
| 212 | if (!priv->ctrl) { |
| 213 | dev_err(&dev->dev, "unable to remap onboard regs\n"); |
| 214 | ret = -ENOMEM; |
| 215 | goto out_pci_release_regions; |
| 216 | } |
| 217 | |
| 218 | /* Read the hex switch on the carrier board */ |
| 219 | priv->hex = ioread8(&priv->ctrl->int_enable); |
| 220 | |
| 221 | /* Add the MODULbus number (hex switch value) to the device's sysfs */ |
| 222 | ret = sysfs_create_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); |
| 223 | if (ret) { |
| 224 | dev_err(&dev->dev, "unable to create sysfs attributes\n"); |
| 225 | goto out_unmap_ctrl; |
| 226 | } |
| 227 | |
| 228 | /* |
| 229 | * Disable all interrupt lines, each submodule will enable its |
| 230 | * own interrupt line if needed |
| 231 | */ |
| 232 | iowrite8(0xf, &priv->ctrl->int_disable); |
| 233 | |
| 234 | /* Register drivers for all submodules */ |
| 235 | ret = cmodio_probe_submodules(priv); |
| 236 | if (ret) { |
| 237 | dev_err(&dev->dev, "unable to probe submodules\n"); |
| 238 | goto out_sysfs_remove_group; |
| 239 | } |
| 240 | |
| 241 | return 0; |
| 242 | |
| 243 | out_sysfs_remove_group: |
| 244 | sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); |
| 245 | out_unmap_ctrl: |
| 246 | iounmap(priv->ctrl); |
| 247 | out_pci_release_regions: |
| 248 | pci_release_regions(dev); |
| 249 | out_pci_disable_device: |
| 250 | pci_disable_device(dev); |
| 251 | out_free_priv: |
| 252 | kfree(priv); |
| 253 | out_return: |
| 254 | return ret; |
| 255 | } |
| 256 | |
| 257 | static void __devexit cmodio_pci_remove(struct pci_dev *dev) |
| 258 | { |
| 259 | struct cmodio_device *priv = pci_get_drvdata(dev); |
| 260 | |
| 261 | mfd_remove_devices(&dev->dev); |
| 262 | sysfs_remove_group(&dev->dev.kobj, &cmodio_sysfs_attr_group); |
| 263 | iounmap(priv->ctrl); |
| 264 | pci_release_regions(dev); |
| 265 | pci_disable_device(dev); |
| 266 | kfree(priv); |
| 267 | } |
| 268 | |
| 269 | #define PCI_VENDOR_ID_JANZ 0x13c3 |
| 270 | |
| 271 | /* The list of devices that this module will support */ |
| 272 | static DEFINE_PCI_DEVICE_TABLE(cmodio_pci_ids) = { |
| 273 | { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_JANZ, 0x0101 }, |
| 274 | { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_VENDOR_ID_JANZ, 0x0100 }, |
| 275 | { 0, } |
| 276 | }; |
| 277 | MODULE_DEVICE_TABLE(pci, cmodio_pci_ids); |
| 278 | |
| 279 | static struct pci_driver cmodio_pci_driver = { |
| 280 | .name = DRV_NAME, |
| 281 | .id_table = cmodio_pci_ids, |
| 282 | .probe = cmodio_pci_probe, |
| 283 | .remove = __devexit_p(cmodio_pci_remove), |
| 284 | }; |
| 285 | |
| 286 | /* |
| 287 | * Module Init / Exit |
| 288 | */ |
| 289 | |
| 290 | static int __init cmodio_init(void) |
| 291 | { |
| 292 | return pci_register_driver(&cmodio_pci_driver); |
| 293 | } |
| 294 | |
| 295 | static void __exit cmodio_exit(void) |
| 296 | { |
| 297 | pci_unregister_driver(&cmodio_pci_driver); |
| 298 | } |
| 299 | |
| 300 | MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>"); |
| 301 | MODULE_DESCRIPTION("Janz CMOD-IO PCI MODULbus Carrier Board Driver"); |
| 302 | MODULE_LICENSE("GPL"); |
| 303 | |
| 304 | module_init(cmodio_init); |
| 305 | module_exit(cmodio_exit); |