arch/arm/boot/dts/armada-xp-db.dts

/*
 * Device Tree file for Marvell Armada XP evaluation board
 * (DB-78460-BP)
 *
 * Copyright (C) 2012-2014 Marvell
 *
 * Lior Amsalem <alior@marvell.com>
 * Gregory CLEMENT <gregory.clement@free-electrons.com>
 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 *
 * This file is dual-licensed: you can use it either under the terms
 * of the GPL or the X11 license, at your option. Note that this dual
 * licensing only applies to this file, and not this project as a
 * whole.
 *
 *  a) This file is free software; you can redistribute it and/or
 *     modify it under the terms of the GNU General Public License as
 *     published by the Free Software Foundation; either version 2 of the
 *     License, or (at your option) any later version.
 *
 *     This file is distributed in the hope that it will be useful,
 *     but WITHOUT ANY WARRANTY; without even the implied warranty of
 *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *     GNU General Public License for more details.
 *
 * Or, alternatively,
 *
 *  b) Permission is hereby granted, free of charge, to any person
 *     obtaining a copy of this software and associated documentation
 *     files (the "Software"), to deal in the Software without
 *     restriction, including without limitation the rights to use,
 *     copy, modify, merge, publish, distribute, sublicense, and/or
 *     sell copies of the Software, and to permit persons to whom the
 *     Software is furnished to do so, subject to the following
 *     conditions:
 *
 *     The above copyright notice and this permission notice shall be
 *     included in all copies or substantial portions of the Software.
 *
 *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
 *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
 *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
 *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
 *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
 *     OTHER DEALINGS IN THE SOFTWARE.
  *
 * Note: this Device Tree assumes that the bootloader has remapped the
 * internal registers to 0xf1000000 (instead of the default
 * 0xd0000000). The 0xf1000000 is the default used by the recent,
 * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
 * boards were delivered with an older version of the bootloader that
 * left internal registers mapped at 0xd0000000. If you are in this
 * situation, you should either update your bootloader (preferred
 * solution) or the below Device Tree should be adjusted.
 */

/dts-v1/;
#include "armada-xp-mv78460.dtsi"

/ {
	model = "Marvell Armada XP Evaluation Board";
	compatible = "marvell,axp-db", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";

	chosen {
		stdout-path = "serial0:115200n8";
	};

	memory@0 {
		device_type = "memory";
		reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
	};

	soc {
		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
			  MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
			  MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
			  MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;

		devbus-bootcs {
			status = "okay";

			/* Device Bus parameters are required */

			/* Read parameters */
			devbus,bus-width    = <16>;
			devbus,turn-off-ps  = <60000>;
			devbus,badr-skew-ps = <0>;
			devbus,acc-first-ps = <124000>;
			devbus,acc-next-ps  = <248000>;
			devbus,rd-setup-ps  = <0>;
			devbus,rd-hold-ps   = <0>;

			/* Write parameters */
			devbus,sync-enable = <0>;
			devbus,wr-high-ps  = <60000>;
			devbus,wr-low-ps   = <60000>;
			devbus,ale-wr-ps   = <60000>;

			/* NOR 16 MiB */
			nor@0 {
				compatible = "cfi-flash";
				reg = <0 0x1000000>;
				bank-width = <2>;
			};
		};

		internal-regs {
			serial@12000 {
				status = "okay";
			};
			serial@12100 {
				status = "okay";
			};
			serial@12200 {
				status = "okay";
			};
			serial@12300 {
				status = "okay";
			};

			sata@a0000 {
				nr-ports = <2>;
				status = "okay";
			};

			ethernet@70000 {
				status = "okay";
				phy = <&phy0>;
				phy-mode = "rgmii-id";
				buffer-manager = <&bm>;
				bm,pool-long = <0>;
			};
			ethernet@74000 {
				status = "okay";
				phy = <&phy1>;
				phy-mode = "rgmii-id";
				buffer-manager = <&bm>;
				bm,pool-long = <1>;
			};
			ethernet@30000 {
				status = "okay";
				phy = <&phy2>;
				phy-mode = "sgmii";
				buffer-manager = <&bm>;
				bm,pool-long = <2>;
			};
			ethernet@34000 {
				status = "okay";
				phy = <&phy3>;
				phy-mode = "sgmii";
				buffer-manager = <&bm>;
				bm,pool-long = <3>;
			};

			bm@c0000 {
				status = "okay";
			};

			mvsdio@d4000 {
				pinctrl-0 = <&sdio_pins>;
				pinctrl-names = "default";
				status = "okay";
				/* No CD or WP GPIOs */
				broken-cd;
			};

			usb@50000 {
				status = "okay";
			};

			usb@51000 {
				status = "okay";
			};

			usb@52000 {
				status = "okay";
			};

			nand@d0000 {
				status = "okay";
				num-cs = <1>;
				marvell,nand-keep-config;
				marvell,nand-enable-arbiter;
				nand-on-flash-bbt;

				partitions {
					compatible = "fixed-partitions";
					#address-cells = <1>;
					#size-cells = <1>;

					partition@0 {
						label = "U-Boot";
						reg = <0 0x800000>;
					};
					partition@800000 {
						label = "Linux";
						reg = <0x800000 0x800000>;
					};
					partition@1000000 {
						label = "Filesystem";
						reg = <0x1000000 0x3f000000>;

					};
				};
			};
		};

		bm-bppi {
			status = "okay";
		};
	};
};

&pciec {
	status = "okay";

	/*
	 * All 6 slots are physically present as
	 * standard PCIe slots on the board.
	 */
	pcie@1,0 {
		/* Port 0, Lane 0 */
		status = "okay";
	};
	pcie@2,0 {
		/* Port 0, Lane 1 */
		status = "okay";
	};
	pcie@3,0 {
		/* Port 0, Lane 2 */
		status = "okay";
	};
	pcie@4,0 {
		/* Port 0, Lane 3 */
		status = "okay";
	};
	pcie@9,0 {
		/* Port 2, Lane 0 */
		status = "okay";
	};
	pcie@10,0 {
		/* Port 3, Lane 0 */
		status = "okay";
	};
};

&mdio {
	phy0: ethernet-phy@0 {
		reg = <0>;
	};

	phy1: ethernet-phy@1 {
		reg = <1>;
	};

	phy2: ethernet-phy@2 {
		reg = <25>;
	};

	phy3: ethernet-phy@3 {
		reg = <27>;
	};
};

&spi0 {
	status = "okay";

	spi-flash@0 {
		#address-cells = <1>;
		#size-cells = <1>;
		compatible = "m25p64", "jedec,spi-nor";
		reg = <0>; /* Chip select 0 */
		spi-max-frequency = <20000000>;
	};
};