Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | # |
| 2 | # USB Host Controller Drivers |
| 3 | # |
| 4 | comment "USB Host Controller Drivers" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 5 | |
Peter Korsgaard | e9b29ff | 2008-04-27 08:59:45 +0200 | [diff] [blame] | 6 | config USB_C67X00_HCD |
| 7 | tristate "Cypress C67x00 HCD support" |
Peter Korsgaard | e9b29ff | 2008-04-27 08:59:45 +0200 | [diff] [blame] | 8 | help |
| 9 | The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role |
| 10 | host/peripheral/OTG USB controllers. |
| 11 | |
| 12 | Enable this option to support this chip in host controller mode. |
| 13 | If unsure, say N. |
| 14 | |
| 15 | To compile this driver as a module, choose M here: the |
| 16 | module will be called c67x00. |
| 17 | |
Sarah Sharp | eb6bab1 | 2009-04-29 19:07:13 -0700 | [diff] [blame] | 18 | config USB_XHCI_HCD |
Greg Kroah-Hartman | eb83be9 | 2012-09-14 21:15:50 -0700 | [diff] [blame] | 19 | tristate "xHCI HCD (USB 3.0) support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 20 | depends on USB_ARCH_HAS_XHCI |
Sarah Sharp | eb6bab1 | 2009-04-29 19:07:13 -0700 | [diff] [blame] | 21 | ---help--- |
| 22 | The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0 |
| 23 | "SuperSpeed" host controller hardware. |
| 24 | |
| 25 | To compile this driver as a module, choose M here: the |
| 26 | module will be called xhci-hcd. |
| 27 | |
Florian Fainelli | 0fcb998 | 2013-04-09 14:29:29 +0200 | [diff] [blame] | 28 | if USB_XHCI_HCD |
| 29 | |
Sebastian Andrzej Siewior | 3429e91 | 2012-03-13 16:57:41 +0200 | [diff] [blame] | 30 | config USB_XHCI_PLATFORM |
| 31 | tristate |
Sebastian Andrzej Siewior | 3429e91 | 2012-03-13 16:57:41 +0200 | [diff] [blame] | 32 | |
Sarah Sharp | eb6bab1 | 2009-04-29 19:07:13 -0700 | [diff] [blame] | 33 | config USB_XHCI_HCD_DEBUGGING |
| 34 | bool "Debugging for the xHCI host controller" |
Sarah Sharp | eb6bab1 | 2009-04-29 19:07:13 -0700 | [diff] [blame] | 35 | ---help--- |
| 36 | Say 'Y' to turn on debugging for the xHCI host controller driver. |
| 37 | This will spew debugging output, even in interrupt context. |
| 38 | This should only be used for debugging xHCI driver bugs. |
| 39 | |
| 40 | If unsure, say N. |
| 41 | |
Florian Fainelli | 0fcb998 | 2013-04-09 14:29:29 +0200 | [diff] [blame] | 42 | endif # USB_XHCI_HCD |
| 43 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 44 | config USB_EHCI_HCD |
| 45 | tristate "EHCI HCD (USB 2.0) support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 46 | depends on USB_ARCH_HAS_EHCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 47 | ---help--- |
| 48 | The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0 |
| 49 | "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware. |
| 50 | If your USB host controller supports USB 2.0, you will likely want to |
Thierry Vignaud | b967c88 | 2009-02-11 13:31:05 -0800 | [diff] [blame] | 51 | configure this Host Controller Driver. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 52 | |
| 53 | EHCI controllers are packaged with "companion" host controllers (OHCI |
| 54 | or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports |
Jesper Juhl | b3c29d8 | 2006-01-10 00:35:22 +0100 | [diff] [blame] | 55 | will connect to EHCI if the device is high speed, otherwise they |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 56 | connect to a companion controller. If you configure EHCI, you should |
| 57 | probably configure the OHCI (for NEC and some other vendors) USB Host |
| 58 | Controller Driver or UHCI (for Via motherboards) Host Controller |
| 59 | Driver too. |
| 60 | |
| 61 | You may want to read <file:Documentation/usb/ehci.txt>. |
| 62 | |
| 63 | To compile this driver as a module, choose M here: the |
| 64 | module will be called ehci-hcd. |
| 65 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 66 | config USB_EHCI_ROOT_HUB_TT |
Robert P. J. Day | 9ec249a | 2008-03-08 03:27:44 -0500 | [diff] [blame] | 67 | bool "Root Hub Transaction Translators" |
Marek Vasut | b12909b | 2012-05-15 06:10:20 +0200 | [diff] [blame] | 68 | depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 69 | ---help--- |
| 70 | Some EHCI chips have vendor-specific extensions to integrate |
| 71 | transaction translators, so that no OHCI or UHCI companion |
| 72 | controller is needed. It's safe to say "y" even if your |
| 73 | controller doesn't support this feature. |
| 74 | |
Dan Streetman | ba47f66 | 2006-05-24 09:39:16 -0700 | [diff] [blame] | 75 | This supports the EHCI implementation that's originally |
| 76 | from ARC, and has since changed hands a few times. |
| 77 | |
| 78 | config USB_EHCI_TT_NEWSCHED |
Alan Stern | 37cd681 | 2010-05-21 17:08:21 -0400 | [diff] [blame] | 79 | bool "Improved Transaction Translator scheduling" |
Marek Vasut | b12909b | 2012-05-15 06:10:20 +0200 | [diff] [blame] | 80 | depends on USB_EHCI_HCD || USB_CHIPIDEA_HOST |
Alan Stern | 37cd681 | 2010-05-21 17:08:21 -0400 | [diff] [blame] | 81 | default y |
Dan Streetman | ba47f66 | 2006-05-24 09:39:16 -0700 | [diff] [blame] | 82 | ---help--- |
| 83 | This changes the periodic scheduling code to fill more of the low |
| 84 | and full speed bandwidth available from the Transaction Translator |
| 85 | (TT) in USB 2.0 hubs. Without this, only one transfer will be |
| 86 | issued in each microframe, significantly reducing the number of |
| 87 | periodic low/fullspeed transfers possible. |
| 88 | |
| 89 | If you have multiple periodic low/fullspeed devices connected to a |
| 90 | highspeed USB hub which is connected to a highspeed USB Host |
| 91 | Controller, and some of those devices will not work correctly |
Alan Stern | 37cd681 | 2010-05-21 17:08:21 -0400 | [diff] [blame] | 92 | (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if |
| 93 | you have only one such device and it doesn't work, you could try |
| 94 | saying N. |
Dan Streetman | ba47f66 | 2006-05-24 09:39:16 -0700 | [diff] [blame] | 95 | |
Alan Stern | 37cd681 | 2010-05-21 17:08:21 -0400 | [diff] [blame] | 96 | If unsure, say Y. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 97 | |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 98 | config USB_FSL_MPH_DR_OF |
| 99 | tristate |
| 100 | |
| 101 | if USB_EHCI_HCD |
| 102 | |
Alan Stern | adfa79d | 2012-11-01 11:13:04 -0400 | [diff] [blame] | 103 | config USB_EHCI_PCI |
| 104 | tristate |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 105 | depends on PCI |
Alan Stern | adfa79d | 2012-11-01 11:13:04 -0400 | [diff] [blame] | 106 | default y |
| 107 | |
Anoop | 22ced687 | 2011-02-24 19:26:28 +0530 | [diff] [blame] | 108 | config USB_EHCI_HCD_PMC_MSP |
| 109 | tristate "EHCI support for on-chip PMC MSP71xx USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 110 | depends on MSP_HAS_USB |
Anoop | 22ced687 | 2011-02-24 19:26:28 +0530 | [diff] [blame] | 111 | default n |
| 112 | select USB_EHCI_BIG_ENDIAN_DESC |
| 113 | select USB_EHCI_BIG_ENDIAN_MMIO |
| 114 | ---help--- |
| 115 | Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's. |
| 116 | If unsure, say N. |
| 117 | |
Benjamin Herrenschmidt | 083522d | 2006-12-15 06:54:08 +1100 | [diff] [blame] | 118 | config USB_EHCI_BIG_ENDIAN_MMIO |
| 119 | bool |
Benjamin Herrenschmidt | 083522d | 2006-12-15 06:54:08 +1100 | [diff] [blame] | 120 | |
Stefan Roese | 6dbd682 | 2007-05-01 09:29:37 -0700 | [diff] [blame] | 121 | config USB_EHCI_BIG_ENDIAN_DESC |
| 122 | bool |
Stefan Roese | 6dbd682 | 2007-05-01 09:29:37 -0700 | [diff] [blame] | 123 | |
Julie Zhu | 08d3c18 | 2009-09-21 16:08:19 -0600 | [diff] [blame] | 124 | config XPS_USB_HCD_XILINX |
| 125 | bool "Use Xilinx usb host EHCI controller core" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 126 | depends on (PPC32 || MICROBLAZE) |
Julie Zhu | 08d3c18 | 2009-09-21 16:08:19 -0600 | [diff] [blame] | 127 | select USB_EHCI_BIG_ENDIAN_DESC |
| 128 | select USB_EHCI_BIG_ENDIAN_MMIO |
| 129 | ---help--- |
| 130 | Xilinx xps USB host controller core is EHCI compilant and has |
| 131 | transaction translator built-in. It can be configured to either |
| 132 | support both high speed and full speed devices, or high speed |
| 133 | devices only. |
| 134 | |
Li Yang | ba02978 | 2007-05-11 17:09:55 +0800 | [diff] [blame] | 135 | config USB_EHCI_FSL |
Fabio Estevam | c0ca9bc | 2012-02-02 14:23:34 -0200 | [diff] [blame] | 136 | bool "Support for Freescale PPC on-chip EHCI USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 137 | depends on FSL_SOC |
Li Yang | ba02978 | 2007-05-11 17:09:55 +0800 | [diff] [blame] | 138 | select USB_EHCI_ROOT_HUB_TT |
Marc Kleine-Budde | 018b97d | 2010-10-29 11:04:49 +0200 | [diff] [blame] | 139 | select USB_FSL_MPH_DR_OF if OF |
Li Yang | ba02978 | 2007-05-11 17:09:55 +0800 | [diff] [blame] | 140 | ---help--- |
| 141 | Variation of ARC USB block used in some Freescale chips. |
| 142 | |
Daniel Mack | 7e8d5cd | 2009-10-28 01:14:59 +0100 | [diff] [blame] | 143 | config USB_EHCI_MXC |
Alan Stern | dba63b2 | 2013-01-23 13:26:15 -0500 | [diff] [blame] | 144 | tristate "Support for Freescale i.MX on-chip EHCI USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 145 | depends on ARCH_MXC |
Daniel Mack | 7e8d5cd | 2009-10-28 01:14:59 +0100 | [diff] [blame] | 146 | select USB_EHCI_ROOT_HUB_TT |
| 147 | ---help--- |
| 148 | Variation of ARC USB block used in some Freescale chips. |
| 149 | |
Keshava Munegowda | 7f124f4 | 2010-11-21 23:23:41 +0530 | [diff] [blame] | 150 | config USB_EHCI_HCD_OMAP |
Alan Stern | 54a41966 | 2013-03-12 12:44:39 +0200 | [diff] [blame] | 151 | tristate "EHCI support for OMAP3 and later chips" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 152 | depends on ARCH_OMAP |
Keshava Munegowda | 7f124f4 | 2010-11-21 23:23:41 +0530 | [diff] [blame] | 153 | default y |
Paul Bolle | d132d7f | 2012-05-07 11:14:59 +0200 | [diff] [blame] | 154 | ---help--- |
Keshava Munegowda | 7f124f4 | 2010-11-21 23:23:41 +0530 | [diff] [blame] | 155 | Enables support for the on-chip EHCI controller on |
| 156 | OMAP3 and later chips. |
Roger Quadros | 7c4ebe68 | 2013-04-15 14:50:34 +0300 | [diff] [blame] | 157 | If your system uses a PHY on the USB port, you will need to |
| 158 | enable USB_PHY and the appropriate PHY driver as well. Most |
| 159 | boards need the NOP_USB_XCEIV PHY driver. |
Keshava Munegowda | 7f124f4 | 2010-11-21 23:23:41 +0530 | [diff] [blame] | 160 | |
Manjunath Goudar | a76dd46 | 2013-04-02 18:23:59 +0200 | [diff] [blame] | 161 | config USB_EHCI_HCD_ORION |
| 162 | tristate "Support for Marvell EBU on-chip EHCI USB controller" |
| 163 | depends on USB_EHCI_HCD && PLAT_ORION |
| 164 | default y |
| 165 | ---help--- |
| 166 | Enables support for the on-chip EHCI controller on Marvell's |
| 167 | embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP, |
| 168 | Armada 370. This is different from the EHCI implementation |
| 169 | on Marvell's mobile PXA and MMP SoC, see "EHCI support for |
| 170 | Marvell PXA/MMP USB controller" for those. |
| 171 | |
Manjunath Goudar | 7675d6b | 2013-04-02 18:24:00 +0200 | [diff] [blame] | 172 | config USB_EHCI_HCD_SPEAR |
| 173 | tristate "Support for ST SPEAr on-chip EHCI USB controller" |
| 174 | depends on USB_EHCI_HCD && PLAT_SPEAR |
| 175 | default y |
| 176 | ---help--- |
| 177 | Enables support for the on-chip EHCI controller on |
| 178 | ST SPEAr chips. |
| 179 | |
Manjunath Goudar | 9773696 | 2013-04-02 18:24:02 +0200 | [diff] [blame] | 180 | config USB_EHCI_HCD_AT91 |
| 181 | tristate "Support for Atmel on-chip EHCI USB controller" |
| 182 | depends on USB_EHCI_HCD && ARCH_AT91 |
| 183 | default y |
| 184 | ---help--- |
| 185 | Enables support for the on-chip EHCI controller on |
| 186 | Atmel chips. |
| 187 | |
Pavankumar Kondeti | b0848ae | 2010-12-07 17:53:56 +0530 | [diff] [blame] | 188 | config USB_EHCI_MSM |
Manjunath Goudar | 8c68e84 | 2013-04-02 18:24:03 +0200 | [diff] [blame] | 189 | tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 190 | depends on ARCH_MSM |
Arnd Bergmann | 4626b8d | 2013-04-25 19:29:01 +0200 | [diff] [blame] | 191 | depends on USB_PHY |
Pavankumar Kondeti | b0848ae | 2010-12-07 17:53:56 +0530 | [diff] [blame] | 192 | select USB_EHCI_ROOT_HUB_TT |
Pavankumar Kondeti | dfb2130 | 2011-03-04 22:45:02 +0530 | [diff] [blame] | 193 | select USB_MSM_OTG |
Pavankumar Kondeti | b0848ae | 2010-12-07 17:53:56 +0530 | [diff] [blame] | 194 | ---help--- |
| 195 | Enables support for the USB Host controller present on the |
| 196 | Qualcomm chipsets. Root Hub has inbuilt TT. |
| 197 | This driver depends on OTG driver for PHY initialization, |
Pavankumar Kondeti | 8bb6a16 | 2010-12-07 17:53:57 +0530 | [diff] [blame] | 198 | clock management, powering up VBUS, and power management. |
Pavankumar Kondeti | 8cf28f1 | 2011-02-04 10:08:18 +0530 | [diff] [blame] | 199 | This driver is not supported on boards like trout which |
| 200 | has an external PHY. |
Pavankumar Kondeti | b0848ae | 2010-12-07 17:53:56 +0530 | [diff] [blame] | 201 | |
Benoit Goby | 79ad3b5 | 2011-03-09 16:28:56 -0800 | [diff] [blame] | 202 | config USB_EHCI_TEGRA |
| 203 | boolean "NVIDIA Tegra HCD support" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 204 | depends on ARCH_TEGRA |
Benoit Goby | 79ad3b5 | 2011-03-09 16:28:56 -0800 | [diff] [blame] | 205 | select USB_EHCI_ROOT_HUB_TT |
Felipe Balbi | 75f32ec | 2013-03-20 14:18:28 +0200 | [diff] [blame] | 206 | select USB_PHY |
Benoit Goby | 79ad3b5 | 2011-03-09 16:28:56 -0800 | [diff] [blame] | 207 | help |
| 208 | This driver enables support for the internal USB Host Controllers |
| 209 | found in NVIDIA Tegra SoCs. The controllers are EHCI compliant. |
| 210 | |
Valentine Barshak | da0e8fb | 2007-12-30 15:28:50 -0800 | [diff] [blame] | 211 | config USB_EHCI_HCD_PPC_OF |
| 212 | bool "EHCI support for PPC USB controller on OF platform bus" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 213 | depends on PPC_OF |
Valentine Barshak | da0e8fb | 2007-12-30 15:28:50 -0800 | [diff] [blame] | 214 | default y |
| 215 | ---help--- |
| 216 | Enables support for the USB controller present on the PowerPC |
| 217 | OpenFirmware platform bus. |
| 218 | |
Yoshihiro Shimoda | 60b0bf0 | 2011-03-01 16:58:37 +0900 | [diff] [blame] | 219 | config USB_EHCI_SH |
| 220 | bool "EHCI support for SuperH USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 221 | depends on SUPERH |
Yoshihiro Shimoda | 60b0bf0 | 2011-03-01 16:58:37 +0900 | [diff] [blame] | 222 | ---help--- |
| 223 | Enables support for the on-chip EHCI controller on the SuperH. |
| 224 | If you use the PCI EHCI controller, this option is not necessary. |
| 225 | |
Joonyoung Shim | 1bcc5aa | 2011-04-08 14:08:50 +0900 | [diff] [blame] | 226 | config USB_EHCI_S5P |
Manjunath Goudar | 7edb3da | 2013-04-02 18:24:01 +0200 | [diff] [blame] | 227 | tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 228 | depends on PLAT_S5P |
Greg Kroah-Hartman | e9a92b2 | 2013-02-20 10:25:05 -0800 | [diff] [blame] | 229 | help |
Manjunath Goudar | 7edb3da | 2013-04-02 18:24:01 +0200 | [diff] [blame] | 230 | Enable support for the Samsung S5Pxxxx and Exynos3/4/5 SOC's |
| 231 | on-chip EHCI controller. |
Joonyoung Shim | 1bcc5aa | 2011-04-08 14:08:50 +0900 | [diff] [blame] | 232 | |
Neil Zhang | 3a082ec | 2011-12-20 13:20:23 +0800 | [diff] [blame] | 233 | config USB_EHCI_MV |
Manjunath Goudar | a76dd46 | 2013-04-02 18:23:59 +0200 | [diff] [blame] | 234 | bool "EHCI support for Marvell PXA/MMP USB controller" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 235 | depends on (ARCH_PXA || ARCH_MMP) |
Neil Zhang | 3a082ec | 2011-12-20 13:20:23 +0800 | [diff] [blame] | 236 | select USB_EHCI_ROOT_HUB_TT |
| 237 | ---help--- |
| 238 | Enables support for Marvell (including PXA and MMP series) on-chip |
| 239 | USB SPH and OTG controller. SPH is a single port host, and it can |
| 240 | only be EHCI host. OTG is controller that can switch to host mode. |
Manjunath Goudar | a76dd46 | 2013-04-02 18:23:59 +0200 | [diff] [blame] | 241 | Note that this driver will not work on Marvell's other EHCI |
| 242 | controller used by the EBU-type SoCs including Orion, Kirkwood, |
| 243 | Dova, Armada 370 and Armada XP. See "Support for Marvell EBU |
| 244 | on-chip EHCI USB controller" for those. |
Neil Zhang | 3a082ec | 2011-12-20 13:20:23 +0800 | [diff] [blame] | 245 | |
Wan ZongShun | 586dfc8 | 2009-06-13 09:14:28 +0800 | [diff] [blame] | 246 | config USB_W90X900_EHCI |
| 247 | bool "W90X900(W90P910) EHCI support" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 248 | depends on ARCH_W90X900 |
Wan ZongShun | 586dfc8 | 2009-06-13 09:14:28 +0800 | [diff] [blame] | 249 | ---help--- |
| 250 | Enables support for the W90X900 USB controller |
| 251 | |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 252 | config USB_CNS3XXX_EHCI |
Florian Fainelli | f3a958d | 2012-10-08 15:11:25 +0200 | [diff] [blame] | 253 | bool "Cavium CNS3XXX EHCI Module (DEPRECATED)" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 254 | depends on ARCH_CNS3XXX |
Florian Fainelli | f3a958d | 2012-10-08 15:11:25 +0200 | [diff] [blame] | 255 | select USB_EHCI_HCD_PLATFORM |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 256 | ---help--- |
Florian Fainelli | f3a958d | 2012-10-08 15:11:25 +0200 | [diff] [blame] | 257 | This option is deprecated now and the driver was removed, use |
| 258 | USB_EHCI_HCD_PLATFORM instead. |
| 259 | |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 260 | Enable support for the CNS3XXX SOC's on-chip EHCI controller. |
| 261 | It is needed for high-speed (480Mbit/sec) USB 2.0 device |
| 262 | support. |
| 263 | |
Gabor Juhos | 502fa84 | 2011-04-13 10:54:22 +0200 | [diff] [blame] | 264 | config USB_EHCI_ATH79 |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 265 | bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)" |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 266 | depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X) |
Gabor Juhos | 502fa84 | 2011-04-13 10:54:22 +0200 | [diff] [blame] | 267 | select USB_EHCI_ROOT_HUB_TT |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 268 | select USB_EHCI_HCD_PLATFORM |
Gabor Juhos | 502fa84 | 2011-04-13 10:54:22 +0200 | [diff] [blame] | 269 | default y |
| 270 | ---help--- |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 271 | This option is deprecated now and the driver was removed, use |
| 272 | USB_EHCI_HCD_PLATFORM instead. |
| 273 | |
Gabor Juhos | 502fa84 | 2011-04-13 10:54:22 +0200 | [diff] [blame] | 274 | Enables support for the built-in EHCI controller present |
| 275 | on the Atheros AR7XXX/AR9XXX SoCs. |
| 276 | |
Florian Fainelli | 42443dc | 2013-04-09 14:29:27 +0200 | [diff] [blame] | 277 | config USB_EHCI_HCD_PLATFORM |
| 278 | tristate "Generic EHCI driver for a platform device" |
| 279 | default n |
| 280 | ---help--- |
| 281 | Adds an EHCI host driver for a generic platform device, which |
| 282 | provides a memory space and an irq. |
| 283 | |
| 284 | If unsure, say N. |
| 285 | |
| 286 | config USB_OCTEON_EHCI |
| 287 | bool "Octeon on-chip EHCI support" |
| 288 | depends on CPU_CAVIUM_OCTEON |
| 289 | default n |
| 290 | select USB_EHCI_BIG_ENDIAN_MMIO |
| 291 | help |
| 292 | Enable support for the Octeon II SOC's on-chip EHCI |
| 293 | controller. It is needed for high-speed (480Mbit/sec) |
| 294 | USB 2.0 device support. All CN6XXX based chips with USB are |
| 295 | supported. |
| 296 | |
| 297 | endif # USB_EHCI_HCD |
| 298 | |
Rodolfo Giometti | b92a78e | 2008-10-23 10:08:07 +0200 | [diff] [blame] | 299 | config USB_OXU210HP_HCD |
| 300 | tristate "OXU210HP HCD support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 301 | depends on GENERIC_HARDIRQS |
Rodolfo Giometti | b92a78e | 2008-10-23 10:08:07 +0200 | [diff] [blame] | 302 | ---help--- |
| 303 | The OXU210HP is an USB host/OTG/device controller. Enable this |
| 304 | option if your board has this chip. If unsure, say N. |
| 305 | |
| 306 | This driver does not support isochronous transfers and doesn't |
| 307 | implement OTG nor USB device controllers. |
| 308 | |
| 309 | To compile this driver as a module, choose M here: the |
| 310 | module will be called oxu210hp-hcd. |
| 311 | |
Olav Kongas | 4808a1c | 2005-04-09 22:57:39 +0300 | [diff] [blame] | 312 | config USB_ISP116X_HCD |
| 313 | tristate "ISP116X HCD support" |
Olav Kongas | 4808a1c | 2005-04-09 22:57:39 +0300 | [diff] [blame] | 314 | ---help--- |
| 315 | The ISP1160 and ISP1161 chips are USB host controllers. Enable this |
| 316 | option if your board has this chip. If unsure, say N. |
| 317 | |
| 318 | This driver does not support isochronous transfers. |
| 319 | |
| 320 | To compile this driver as a module, choose M here: the |
| 321 | module will be called isp116x-hcd. |
| 322 | |
Sebastian Siewior | db11e47 | 2008-04-24 00:37:04 +0200 | [diff] [blame] | 323 | config USB_ISP1760_HCD |
| 324 | tristate "ISP 1760 HCD support" |
Sebastian Siewior | db11e47 | 2008-04-24 00:37:04 +0200 | [diff] [blame] | 325 | ---help--- |
| 326 | The ISP1760 chip is a USB 2.0 host controller. |
| 327 | |
| 328 | This driver does not support isochronous transfers or OTG. |
Sebastian Andrzej Siewior | ff30bf1 | 2008-11-02 15:25:42 +0100 | [diff] [blame] | 329 | This USB controller is usually attached to a non-DMA-Master |
| 330 | capable bus. NXP's eval kit brings this chip on PCI card |
| 331 | where the chip itself is behind a PLB to simulate such |
| 332 | a bus. |
Sebastian Siewior | db11e47 | 2008-04-24 00:37:04 +0200 | [diff] [blame] | 333 | |
| 334 | To compile this driver as a module, choose M here: the |
Sebastian Andrzej Siewior | ff30bf1 | 2008-11-02 15:25:42 +0100 | [diff] [blame] | 335 | module will be called isp1760. |
Sebastian Siewior | db11e47 | 2008-04-24 00:37:04 +0200 | [diff] [blame] | 336 | |
Lothar Wassmann | a9d4309 | 2009-07-16 20:51:21 -0400 | [diff] [blame] | 337 | config USB_ISP1362_HCD |
| 338 | tristate "ISP1362 HCD support" |
Lothar Wassmann | a9d4309 | 2009-07-16 20:51:21 -0400 | [diff] [blame] | 339 | default N |
| 340 | ---help--- |
| 341 | Supports the Philips ISP1362 chip as a host controller |
| 342 | |
| 343 | This driver does not support isochronous transfers. |
| 344 | |
| 345 | To compile this driver as a module, choose M here: the |
| 346 | module will be called isp1362-hcd. |
| 347 | |
Yuan-Hsin Chen | 6c920bfb | 2013-05-17 10:14:14 +0000 | [diff] [blame^] | 348 | config USB_FUSBH200_HCD |
| 349 | tristate "FUSBH200 HCD support" |
| 350 | depends on USB |
| 351 | default N |
| 352 | ---help--- |
| 353 | Faraday FUSBH200 is designed to meet USB2.0 EHCI specification |
| 354 | with minor modification. |
| 355 | |
| 356 | To compile this driver as a module, choose M here: the |
| 357 | module will be called fusbh200-hcd. |
| 358 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 359 | config USB_OHCI_HCD |
| 360 | tristate "OHCI HCD support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 361 | depends on USB_ARCH_HAS_OHCI |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 362 | select ISP1301_OMAP if MACH_OMAP_H2 || MACH_OMAP_H3 |
Linus Torvalds | 61464c8 | 2012-10-01 18:19:05 -0700 | [diff] [blame] | 363 | depends on USB_ISP1301 || !ARCH_LPC32XX |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 364 | ---help--- |
| 365 | The Open Host Controller Interface (OHCI) is a standard for accessing |
| 366 | USB 1.1 host controller hardware. It does more in hardware than Intel's |
| 367 | UHCI specification. If your USB host controller follows the OHCI spec, |
| 368 | say Y. On most non-x86 systems, and on x86 hardware that's not using a |
| 369 | USB controller from Intel or VIA, this is appropriate. If your host |
| 370 | controller doesn't use PCI, this is probably appropriate. For a PCI |
| 371 | based system where you're not sure, the "lspci -v" entry will list the |
| 372 | right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI. |
| 373 | |
| 374 | To compile this driver as a module, choose M here: the |
| 375 | module will be called ohci-hcd. |
| 376 | |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 377 | if USB_OHCI_HCD |
| 378 | |
Anand Gadiyar | 968b448 | 2010-05-10 21:56:12 +0530 | [diff] [blame] | 379 | config USB_OHCI_HCD_OMAP1 |
| 380 | bool "OHCI support for OMAP1/2 chips" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 381 | depends on ARCH_OMAP1 |
Anand Gadiyar | 968b448 | 2010-05-10 21:56:12 +0530 | [diff] [blame] | 382 | default y |
| 383 | ---help--- |
| 384 | Enables support for the OHCI controller on OMAP1/2 chips. |
| 385 | |
| 386 | config USB_OHCI_HCD_OMAP3 |
| 387 | bool "OHCI support for OMAP3 and later chips" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 388 | depends on (ARCH_OMAP3 || ARCH_OMAP4) |
Anand Gadiyar | 968b448 | 2010-05-10 21:56:12 +0530 | [diff] [blame] | 389 | default y |
| 390 | ---help--- |
| 391 | Enables support for the on-chip OHCI controller on |
| 392 | OMAP3 and later chips. |
| 393 | |
Gabor Juhos | 90e6ca5 | 2011-04-13 10:54:24 +0200 | [diff] [blame] | 394 | config USB_OHCI_ATH79 |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 395 | bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 396 | depends on (SOC_AR71XX || SOC_AR724X) |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 397 | select USB_OHCI_HCD_PLATFORM |
Gabor Juhos | 90e6ca5 | 2011-04-13 10:54:24 +0200 | [diff] [blame] | 398 | default y |
| 399 | help |
Hauke Mehrtens | 5d98cd4 | 2012-03-13 01:04:53 +0100 | [diff] [blame] | 400 | This option is deprecated now and the driver was removed, use |
| 401 | USB_OHCI_HCD_PLATFORM instead. |
| 402 | |
Gabor Juhos | 90e6ca5 | 2011-04-13 10:54:24 +0200 | [diff] [blame] | 403 | Enables support for the built-in OHCI controller present on the |
| 404 | Atheros AR71XX/AR7240 SoCs. |
| 405 | |
Sylvain Munaut | 495a678 | 2006-12-13 21:09:55 +0100 | [diff] [blame] | 406 | config USB_OHCI_HCD_PPC_OF_BE |
Arnd Bergmann | 45e8388 | 2009-06-19 05:35:34 -0700 | [diff] [blame] | 407 | bool "OHCI support for OF platform bus (big endian)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 408 | depends on PPC_OF |
Sylvain Munaut | 495a678 | 2006-12-13 21:09:55 +0100 | [diff] [blame] | 409 | select USB_OHCI_BIG_ENDIAN_DESC |
| 410 | select USB_OHCI_BIG_ENDIAN_MMIO |
Arnd Bergmann | 45e8388 | 2009-06-19 05:35:34 -0700 | [diff] [blame] | 411 | ---help--- |
| 412 | Enables support for big-endian USB controllers present on the |
| 413 | OpenFirmware platform bus. |
Sylvain Munaut | 495a678 | 2006-12-13 21:09:55 +0100 | [diff] [blame] | 414 | |
| 415 | config USB_OHCI_HCD_PPC_OF_LE |
Arnd Bergmann | 45e8388 | 2009-06-19 05:35:34 -0700 | [diff] [blame] | 416 | bool "OHCI support for OF platform bus (little endian)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 417 | depends on PPC_OF |
Sylvain Munaut | 495a678 | 2006-12-13 21:09:55 +0100 | [diff] [blame] | 418 | select USB_OHCI_LITTLE_ENDIAN |
Arnd Bergmann | 45e8388 | 2009-06-19 05:35:34 -0700 | [diff] [blame] | 419 | ---help--- |
| 420 | Enables support for little-endian USB controllers present on the |
| 421 | OpenFirmware platform bus. |
| 422 | |
| 423 | config USB_OHCI_HCD_PPC_OF |
| 424 | bool |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 425 | depends on PPC_OF |
Arnd Bergmann | 45e8388 | 2009-06-19 05:35:34 -0700 | [diff] [blame] | 426 | default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE |
Sylvain Munaut | 495a678 | 2006-12-13 21:09:55 +0100 | [diff] [blame] | 427 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 428 | config USB_OHCI_HCD_PCI |
| 429 | bool "OHCI support for PCI-bus USB controllers" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 430 | depends on PCI && (STB03xxx || PPC_MPC52xx || USB_OHCI_HCD_PPC_OF) |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 431 | default y |
| 432 | select USB_OHCI_LITTLE_ENDIAN |
| 433 | ---help--- |
| 434 | Enables support for PCI-bus plug-in USB controller cards. |
| 435 | If unsure, say Y. |
| 436 | |
Michael Buesch | c604e85 | 2007-10-09 23:47:17 -0700 | [diff] [blame] | 437 | config USB_OHCI_HCD_SSB |
Hauke Mehrtens | 259b83a | 2012-03-15 23:49:59 +0100 | [diff] [blame] | 438 | bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 439 | depends on (SSB = y || SSB = USB_OHCI_HCD) |
Hauke Mehrtens | 259b83a | 2012-03-15 23:49:59 +0100 | [diff] [blame] | 440 | select USB_HCD_SSB |
| 441 | select USB_OHCI_HCD_PLATFORM |
Michael Buesch | c604e85 | 2007-10-09 23:47:17 -0700 | [diff] [blame] | 442 | default n |
| 443 | ---help--- |
Hauke Mehrtens | 259b83a | 2012-03-15 23:49:59 +0100 | [diff] [blame] | 444 | This option is deprecated now and the driver was removed, use |
| 445 | USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead. |
| 446 | |
Michael Buesch | c604e85 | 2007-10-09 23:47:17 -0700 | [diff] [blame] | 447 | Support for the Sonics Silicon Backplane (SSB) attached |
| 448 | Broadcom USB OHCI core. |
| 449 | |
| 450 | This device is present in some embedded devices with |
| 451 | Broadcom based SSB bus. |
| 452 | |
| 453 | If unsure, say N. |
| 454 | |
Yoshihiro Shimoda | 60b0bf0 | 2011-03-01 16:58:37 +0900 | [diff] [blame] | 455 | config USB_OHCI_SH |
Florian Fainelli | 231a72e | 2012-10-08 15:11:37 +0200 | [diff] [blame] | 456 | bool "OHCI support for SuperH USB controller (DEPRECATED)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 457 | depends on SUPERH |
Florian Fainelli | 231a72e | 2012-10-08 15:11:37 +0200 | [diff] [blame] | 458 | select USB_OHCI_HCD_PLATFORM |
Yoshihiro Shimoda | 60b0bf0 | 2011-03-01 16:58:37 +0900 | [diff] [blame] | 459 | ---help--- |
Florian Fainelli | 231a72e | 2012-10-08 15:11:37 +0200 | [diff] [blame] | 460 | This option is deprecated now and the driver was removed, use |
| 461 | USB_OHCI_HCD_PLATFORM instead. |
| 462 | |
Yoshihiro Shimoda | 60b0bf0 | 2011-03-01 16:58:37 +0900 | [diff] [blame] | 463 | Enables support for the on-chip OHCI controller on the SuperH. |
| 464 | If you use the PCI OHCI controller, this option is not necessary. |
| 465 | |
Jingoo Han | 6219424 | 2011-12-23 11:20:54 +0900 | [diff] [blame] | 466 | config USB_OHCI_EXYNOS |
| 467 | boolean "OHCI support for Samsung EXYNOS SoC Series" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 468 | depends on ARCH_EXYNOS |
Jingoo Han | 6219424 | 2011-12-23 11:20:54 +0900 | [diff] [blame] | 469 | help |
| 470 | Enable support for the Samsung Exynos SOC's on-chip OHCI controller. |
| 471 | |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 472 | config USB_CNS3XXX_OHCI |
Florian Fainelli | c23920b0 | 2012-10-08 15:11:33 +0200 | [diff] [blame] | 473 | bool "Cavium CNS3XXX OHCI Module (DEPRECATED)" |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 474 | depends on ARCH_CNS3XXX |
Florian Fainelli | c23920b0 | 2012-10-08 15:11:33 +0200 | [diff] [blame] | 475 | select USB_OHCI_HCD_PLATFORM |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 476 | ---help--- |
Florian Fainelli | c23920b0 | 2012-10-08 15:11:33 +0200 | [diff] [blame] | 477 | This option is deprecated now and the driver was removed, use |
| 478 | USB_OHCI_HCD_PLATFORM instead. |
| 479 | |
Mac Lin | 760efe6 | 2010-11-25 23:58:00 +0800 | [diff] [blame] | 480 | Enable support for the CNS3XXX SOC's on-chip OHCI controller. |
| 481 | It is needed for low-speed USB 1.0 device support. |
| 482 | |
Hauke Mehrtens | fa3364b | 2012-03-13 01:04:47 +0100 | [diff] [blame] | 483 | config USB_OHCI_HCD_PLATFORM |
| 484 | bool "Generic OHCI driver for a platform device" |
Hauke Mehrtens | fa3364b | 2012-03-13 01:04:47 +0100 | [diff] [blame] | 485 | default n |
| 486 | ---help--- |
| 487 | Adds an OHCI host driver for a generic platform device, which |
Peter Meerwald | 898d828 | 2012-08-18 15:53:12 +0200 | [diff] [blame] | 488 | provides a memory space and an irq. |
Hauke Mehrtens | fa3364b | 2012-03-13 01:04:47 +0100 | [diff] [blame] | 489 | |
| 490 | If unsure, say N. |
| 491 | |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 492 | config USB_OCTEON_OHCI |
| 493 | bool "Octeon on-chip OHCI support" |
| 494 | depends on CPU_CAVIUM_OCTEON |
| 495 | default USB_OCTEON_EHCI |
| 496 | select USB_OHCI_BIG_ENDIAN_MMIO |
| 497 | select USB_OHCI_LITTLE_ENDIAN |
| 498 | help |
| 499 | Enable support for the Octeon II SOC's on-chip OHCI |
| 500 | controller. It is needed for low-speed USB 1.0 device |
| 501 | support. All CN6XXX based chips with USB are supported. |
| 502 | |
Hauke Mehrtens | 7a7a4a59 | 2012-03-13 01:04:48 +0100 | [diff] [blame] | 503 | |
Benjamin Herrenschmidt | 11d1a4a | 2006-12-15 06:54:03 +1100 | [diff] [blame] | 504 | config USB_OHCI_BIG_ENDIAN_DESC |
| 505 | bool |
Benjamin Herrenschmidt | 11d1a4a | 2006-12-15 06:54:03 +1100 | [diff] [blame] | 506 | default n |
| 507 | |
| 508 | config USB_OHCI_BIG_ENDIAN_MMIO |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 509 | bool |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 510 | default n |
| 511 | |
| 512 | config USB_OHCI_LITTLE_ENDIAN |
| 513 | bool |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 514 | default n if STB03xxx || PPC_MPC52xx |
| 515 | default y |
| 516 | |
Florian Fainelli | 3ad3ca0 | 2013-04-09 14:29:28 +0200 | [diff] [blame] | 517 | endif # USB_OHCI_HCD |
| 518 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 519 | config USB_UHCI_HCD |
| 520 | tristate "UHCI HCD (most Intel and VIA) support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 521 | depends on PCI || SPARC_LEON || ARCH_VT8500 |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 522 | ---help--- |
| 523 | The Universal Host Controller Interface is a standard by Intel for |
| 524 | accessing the USB hardware in the PC (which is also called the USB |
| 525 | host controller). If your USB host controller conforms to this |
| 526 | standard, you may want to say Y, but see below. All recent boards |
| 527 | with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX, |
| 528 | i810, i820) conform to this standard. Also all VIA PCI chipsets |
| 529 | (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro |
Jan Andersson | 3db7739 | 2011-05-06 12:00:18 +0200 | [diff] [blame] | 530 | 133) and LEON/GRLIB SoCs with the GRUSBHC controller. |
| 531 | If unsure, say Y. |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 532 | |
| 533 | To compile this driver as a module, choose M here: the |
| 534 | module will be called uhci-hcd. |
| 535 | |
Jan Andersson | d3219d1 | 2011-05-06 12:00:17 +0200 | [diff] [blame] | 536 | config USB_UHCI_SUPPORT_NON_PCI_HC |
| 537 | bool |
| 538 | depends on USB_UHCI_HCD |
Tony Prisk | 100d459 | 2012-07-21 22:58:53 +1200 | [diff] [blame] | 539 | default y if (SPARC_LEON || ARCH_VT8500) |
| 540 | |
| 541 | config USB_UHCI_PLATFORM |
| 542 | bool "Generic UHCI Platform Driver support" |
| 543 | depends on USB_UHCI_SUPPORT_NON_PCI_HC |
| 544 | default y if ARCH_VT8500 |
| 545 | ---help--- |
| 546 | Enable support for generic UHCI platform devices that require no |
| 547 | additional configuration. |
Jan Andersson | d3219d1 | 2011-05-06 12:00:17 +0200 | [diff] [blame] | 548 | |
Jan Andersson | 8452c67 | 2011-05-18 10:44:49 +0200 | [diff] [blame] | 549 | config USB_UHCI_BIG_ENDIAN_MMIO |
| 550 | bool |
Jan Andersson | fda928a | 2011-05-18 10:44:53 +0200 | [diff] [blame] | 551 | depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON |
| 552 | default y |
Jan Andersson | 8452c67 | 2011-05-18 10:44:49 +0200 | [diff] [blame] | 553 | |
Jan Andersson | 51e2f62 | 2011-05-18 10:44:51 +0200 | [diff] [blame] | 554 | config USB_UHCI_BIG_ENDIAN_DESC |
| 555 | bool |
Jan Andersson | fda928a | 2011-05-18 10:44:53 +0200 | [diff] [blame] | 556 | depends on USB_UHCI_SUPPORT_NON_PCI_HC && SPARC_LEON |
| 557 | default y |
Jan Andersson | 51e2f62 | 2011-05-18 10:44:51 +0200 | [diff] [blame] | 558 | |
Anton Vorontsov | 236dd4d | 2009-01-10 05:03:21 +0300 | [diff] [blame] | 559 | config USB_FHCI_HCD |
| 560 | tristate "Freescale QE USB Host Controller support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 561 | depends on OF_GPIO && QE_GPIO && QUICC_ENGINE |
Anton Vorontsov | 236dd4d | 2009-01-10 05:03:21 +0300 | [diff] [blame] | 562 | select FSL_GTM |
| 563 | select QE_USB |
| 564 | help |
| 565 | This driver enables support for Freescale QE USB Host Controller |
| 566 | (as found on MPC8360 and MPC8323 processors), the driver supports |
| 567 | Full and Low Speed USB. |
| 568 | |
| 569 | config FHCI_DEBUG |
| 570 | bool "Freescale QE USB Host Controller debug support" |
| 571 | depends on USB_FHCI_HCD && DEBUG_FS |
| 572 | help |
| 573 | Say "y" to see some FHCI debug information and statistics |
Lucas De Marchi | 25985ed | 2011-03-30 22:57:33 -0300 | [diff] [blame] | 574 | through debugfs. |
Anton Vorontsov | 236dd4d | 2009-01-10 05:03:21 +0300 | [diff] [blame] | 575 | |
Tony Olech | d774efe | 2006-09-13 11:27:35 +0100 | [diff] [blame] | 576 | config USB_U132_HCD |
| 577 | tristate "Elan U132 Adapter Host Controller" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 578 | depends on USB_FTDI_ELAN |
Tony Olech | d774efe | 2006-09-13 11:27:35 +0100 | [diff] [blame] | 579 | default M |
| 580 | help |
| 581 | The U132 adapter is a USB to CardBus adapter specifically designed |
| 582 | for PC cards that contain an OHCI host controller. Typical PC cards |
| 583 | are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132 |
| 584 | adapter will *NOT* work with PC cards that do not contain an OHCI |
| 585 | controller. |
| 586 | |
Matt LaPlante | 3cb2fcc | 2006-11-30 05:22:59 +0100 | [diff] [blame] | 587 | For those PC cards that contain multiple OHCI controllers only the |
Tony Olech | d774efe | 2006-09-13 11:27:35 +0100 | [diff] [blame] | 588 | first one is used. |
| 589 | |
| 590 | The driver consists of two modules, the "ftdi-elan" module is a |
| 591 | USB client driver that interfaces to the FTDI chip within ELAN's |
| 592 | USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host |
| 593 | controller driver that talks to the OHCI controller within the |
| 594 | CardBus cards that are inserted in the U132 adapter. |
| 595 | |
| 596 | This driver has been tested with a CardBus OHCI USB adapter, and |
| 597 | worked with a USB PEN Drive inserted into the first USB port of |
| 598 | the PCCARD. A rather pointless thing to do, but useful for testing. |
| 599 | |
| 600 | It is safe to say M here. |
| 601 | |
| 602 | See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php> |
| 603 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 604 | config USB_SL811_HCD |
| 605 | tristate "SL811HS HCD support" |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 606 | help |
| 607 | The SL811HS is a single-port USB controller that supports either |
| 608 | host side or peripheral side roles. Enable this option if your |
| 609 | board has this chip, and you want to use it as a host controller. |
| 610 | If unsure, say N. |
| 611 | |
| 612 | To compile this driver as a module, choose M here: the |
| 613 | module will be called sl811-hcd. |
| 614 | |
Mike Frysinger | ad7c56f | 2011-03-22 15:35:39 -0400 | [diff] [blame] | 615 | config USB_SL811_HCD_ISO |
| 616 | bool "partial ISO support" |
| 617 | depends on USB_SL811_HCD |
| 618 | help |
| 619 | The driver doesn't support iso_frame_desc (yet), but for some simple |
| 620 | devices that just queue one ISO frame per URB, then ISO transfers |
| 621 | "should" work using the normal urb status fields. |
| 622 | |
| 623 | If unsure, say N. |
| 624 | |
David Brownell | c6de2b6 | 2005-05-26 05:55:55 -0700 | [diff] [blame] | 625 | config USB_SL811_CS |
| 626 | tristate "CF/PCMCIA support for SL811HS HCD" |
| 627 | depends on USB_SL811_HCD && PCMCIA |
David Brownell | c6de2b6 | 2005-05-26 05:55:55 -0700 | [diff] [blame] | 628 | help |
| 629 | Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC |
| 630 | REX-CFU1U CF card (often used with PDAs). If unsure, say N. |
| 631 | |
| 632 | To compile this driver as a module, choose M here: the |
| 633 | module will be called "sl811_cs". |
| 634 | |
Yoshihiro Shimoda | 5d30435 | 2007-05-10 13:18:19 +0900 | [diff] [blame] | 635 | config USB_R8A66597_HCD |
M4rkusXXL | fa0de2b | 2007-08-10 14:53:32 -0700 | [diff] [blame] | 636 | tristate "R8A66597 HCD support" |
Yoshihiro Shimoda | 5d30435 | 2007-05-10 13:18:19 +0900 | [diff] [blame] | 637 | help |
| 638 | The R8A66597 is a USB 2.0 host and peripheral controller. |
| 639 | |
| 640 | Enable this option if your board has this chip, and you want |
| 641 | to use it as a host controller. If unsure, say N. |
| 642 | |
| 643 | To compile this driver as a module, choose M here: the |
| 644 | module will be called r8a66597-hcd. |
| 645 | |
Kuninori Morimoto | 034d7c1 | 2011-10-10 22:07:40 -0700 | [diff] [blame] | 646 | config USB_RENESAS_USBHS_HCD |
| 647 | tristate "Renesas USBHS HCD support" |
Kuninori Morimoto | 034d7c1 | 2011-10-10 22:07:40 -0700 | [diff] [blame] | 648 | depends on USB_RENESAS_USBHS |
| 649 | help |
| 650 | The Renesas USBHS is a USB 2.0 host and peripheral controller. |
| 651 | |
| 652 | Enable this option if your board has this chip, and you want |
| 653 | to use it as a host controller. If unsure, say N. |
| 654 | |
| 655 | To compile this driver as a module, choose M here: the |
| 656 | module will be called renesas-usbhs. |
| 657 | |
David Vrabel | 7e6133a | 2008-09-17 16:34:28 +0100 | [diff] [blame] | 658 | config USB_WHCI_HCD |
Greg Kroah-Hartman | eb83be9 | 2012-09-14 21:15:50 -0700 | [diff] [blame] | 659 | tristate "Wireless USB Host Controller Interface (WHCI) driver" |
Randy Dunlap | 36f8ecb | 2012-01-27 15:47:03 -0800 | [diff] [blame] | 660 | depends on PCI && USB && UWB |
David Vrabel | 7e6133a | 2008-09-17 16:34:28 +0100 | [diff] [blame] | 661 | select USB_WUSB |
| 662 | select UWB_WHCI |
| 663 | help |
| 664 | A driver for PCI-based Wireless USB Host Controllers that are |
| 665 | compliant with the WHCI specification. |
| 666 | |
| 667 | To compile this driver a module, choose M here: the module |
| 668 | will be called "whci-hcd". |
Inaky Perez-Gonzalez | d09318b | 2008-09-17 16:34:30 +0100 | [diff] [blame] | 669 | |
| 670 | config USB_HWA_HCD |
Greg Kroah-Hartman | eb83be9 | 2012-09-14 21:15:50 -0700 | [diff] [blame] | 671 | tristate "Host Wire Adapter (HWA) driver" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 672 | depends on UWB |
Inaky Perez-Gonzalez | d09318b | 2008-09-17 16:34:30 +0100 | [diff] [blame] | 673 | select USB_WUSB |
| 674 | select UWB_HWA |
| 675 | help |
| 676 | This driver enables you to connect Wireless USB devices to |
| 677 | your system using a Host Wire Adaptor USB dongle. This is an |
| 678 | UWB Radio Controller and WUSB Host Controller connected to |
| 679 | your machine via USB (specified in WUSB1.0). |
| 680 | |
| 681 | To compile this driver a module, choose M here: the module |
| 682 | will be called "hwa-hc". |
Martin Fuzzey | 23d3e7a | 2009-11-21 12:14:48 +0100 | [diff] [blame] | 683 | |
| 684 | config USB_IMX21_HCD |
Sascha Hauer | 5de9ec4 | 2011-08-24 08:41:10 +0200 | [diff] [blame] | 685 | tristate "i.MX21 HCD support" |
Florian Fainelli | 25e11ec | 2013-04-09 14:29:25 +0200 | [diff] [blame] | 686 | depends on ARM && ARCH_MXC |
Martin Fuzzey | 23d3e7a | 2009-11-21 12:14:48 +0100 | [diff] [blame] | 687 | help |
| 688 | This driver enables support for the on-chip USB host in the |
Sascha Hauer | 5de9ec4 | 2011-08-24 08:41:10 +0200 | [diff] [blame] | 689 | i.MX21 processor. |
Martin Fuzzey | 23d3e7a | 2009-11-21 12:14:48 +0100 | [diff] [blame] | 690 | |
| 691 | To compile this driver as a module, choose M here: the |
| 692 | module will be called "imx21-hcd". |
| 693 | |
David Daney | 1643acc | 2010-10-08 14:47:52 -0700 | [diff] [blame] | 694 | |
David Daney | 1643acc | 2010-10-08 14:47:52 -0700 | [diff] [blame] | 695 | |
| 696 | config USB_OCTEON2_COMMON |
| 697 | bool |
| 698 | default y if USB_OCTEON_EHCI || USB_OCTEON_OHCI |
Hauke Mehrtens | 62e11d1 | 2012-03-15 23:49:57 +0100 | [diff] [blame] | 699 | |
| 700 | config USB_HCD_BCMA |
| 701 | tristate "BCMA usb host driver" |
Greg Kroah-Hartman | eb83be9 | 2012-09-14 21:15:50 -0700 | [diff] [blame] | 702 | depends on BCMA |
Hauke Mehrtens | 62e11d1 | 2012-03-15 23:49:57 +0100 | [diff] [blame] | 703 | select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD |
| 704 | select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD |
| 705 | help |
Jesper Dangaard Brouer | 71c421d | 2012-06-15 12:01:33 +0200 | [diff] [blame] | 706 | Enable support for the EHCI and OCHI host controller on an bcma bus. |
Hauke Mehrtens | 62e11d1 | 2012-03-15 23:49:57 +0100 | [diff] [blame] | 707 | It converts the bcma driver into two platform device drivers |
| 708 | for ehci and ohci. |
| 709 | |
| 710 | If unsure, say N. |
Hauke Mehrtens | 7043c2c | 2012-03-15 23:49:58 +0100 | [diff] [blame] | 711 | |
| 712 | config USB_HCD_SSB |
| 713 | tristate "SSB usb host driver" |
Greg Kroah-Hartman | eb83be9 | 2012-09-14 21:15:50 -0700 | [diff] [blame] | 714 | depends on SSB |
Hauke Mehrtens | 7043c2c | 2012-03-15 23:49:58 +0100 | [diff] [blame] | 715 | select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD |
| 716 | select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD |
| 717 | help |
Jesper Dangaard Brouer | 71c421d | 2012-06-15 12:01:33 +0200 | [diff] [blame] | 718 | Enable support for the EHCI and OCHI host controller on an bcma bus. |
Hauke Mehrtens | 7043c2c | 2012-03-15 23:49:58 +0100 | [diff] [blame] | 719 | It converts the bcma driver into two platform device drivers |
| 720 | for ehci and ohci. |
| 721 | |
| 722 | If unsure, say N. |