Documentation/kbuild/makefiles.txt

Linux Kernel Makefiles

This document describes the Linux kernel Makefiles.

=== Table of Contents

	=== 1 Overview
	=== 2 Who does what
	=== 3 The kbuild files
	   --- 3.1 Goal definitions
	   --- 3.2 Built-in object goals - obj-y
	   --- 3.3 Loadable module goals - obj-m
	   --- 3.4 Objects which export symbols
	   --- 3.5 Library file goals - lib-y
	   --- 3.6 Descending down in directories
	   --- 3.7 Compilation flags
	   --- 3.8 Command line dependency
	   --- 3.9 Dependency tracking
	   --- 3.10 Special Rules
	   --- 3.11 $(CC) support functions
	   --- 3.12 $(LD) support functions

	=== 4 Host Program support
	   --- 4.1 Simple Host Program
	   --- 4.2 Composite Host Programs
	   --- 4.3 Using C++ for host programs
	   --- 4.4 Controlling compiler options for host programs
	   --- 4.5 When host programs are actually built
	   --- 4.6 Using hostprogs-$(CONFIG_FOO)

	=== 5 Kbuild clean infrastructure

	=== 6 Architecture Makefiles
	   --- 6.1 Set variables to tweak the build to the architecture
	   --- 6.2 Add prerequisites to archheaders:
	   --- 6.3 Add prerequisites to archprepare:
	   --- 6.4 List directories to visit when descending
	   --- 6.5 Architecture-specific boot images
	   --- 6.6 Building non-kbuild targets
	   --- 6.7 Commands useful for building a boot image
	   --- 6.8 Custom kbuild commands
	   --- 6.9 Preprocessing linker scripts
	   --- 6.10 Generic header files
	   --- 6.11 Post-link pass

	=== 7 Kbuild syntax for exported headers
		--- 7.1 no-export-headers
		--- 7.2 generic-y
		--- 7.3 generated-y
		--- 7.4 mandatory-y

	=== 8 Kbuild Variables
	=== 9 Makefile language
	=== 10 Credits
	=== 11 TODO

=== 1 Overview

The Makefiles have five parts:

	Makefile		the top Makefile.
	.config			the kernel configuration file.
	arch/$(ARCH)/Makefile	the arch Makefile.
	scripts/Makefile.*	common rules etc. for all kbuild Makefiles.
	kbuild Makefiles	there are about 500 of these.

The top Makefile reads the .config file, which comes from the kernel
configuration process.

The top Makefile is responsible for building two major products: vmlinux
(the resident kernel image) and modules (any module files).
It builds these goals by recursively descending into the subdirectories of
the kernel source tree.
The list of subdirectories which are visited depends upon the kernel
configuration. The top Makefile textually includes an arch Makefile
with the name arch/$(ARCH)/Makefile. The arch Makefile supplies
architecture-specific information to the top Makefile.

Each subdirectory has a kbuild Makefile which carries out the commands
passed down from above. The kbuild Makefile uses information from the
.config file to construct various file lists used by kbuild to build
any built-in or modular targets.

scripts/Makefile.* contains all the definitions/rules etc. that
are used to build the kernel based on the kbuild makefiles.


=== 2 Who does what

People have four different relationships with the kernel Makefiles.

*Users* are people who build kernels.  These people type commands such as
"make menuconfig" or "make".  They usually do not read or edit
any kernel Makefiles (or any other source files).

*Normal developers* are people who work on features such as device
drivers, file systems, and network protocols.  These people need to
maintain the kbuild Makefiles for the subsystem they are
working on.  In order to do this effectively, they need some overall
knowledge about the kernel Makefiles, plus detailed knowledge about the
public interface for kbuild.

*Arch developers* are people who work on an entire architecture, such
as sparc or ia64.  Arch developers need to know about the arch Makefile
as well as kbuild Makefiles.

*Kbuild developers* are people who work on the kernel build system itself.
These people need to know about all aspects of the kernel Makefiles.

This document is aimed towards normal developers and arch developers.


=== 3 The kbuild files

Most Makefiles within the kernel are kbuild Makefiles that use the
kbuild infrastructure. This chapter introduces the syntax used in the
kbuild makefiles.
The preferred name for the kbuild files are 'Makefile' but 'Kbuild' can
be used and if both a 'Makefile' and a 'Kbuild' file exists, then the 'Kbuild'
file will be used.

Section 3.1 "Goal definitions" is a quick intro, further chapters provide
more details, with real examples.

--- 3.1 Goal definitions

	Goal definitions are the main part (heart) of the kbuild Makefile.
	These lines define the files to be built, any special compilation
	options, and any subdirectories to be entered recursively.

	The most simple kbuild makefile contains one line:

	Example:
		obj-y += foo.o

	This tells kbuild that there is one object in that directory, named
	foo.o. foo.o will be built from foo.c or foo.S.

	If foo.o shall be built as a module, the variable obj-m is used.
	Therefore the following pattern is often used:

	Example:
		obj-$(CONFIG_FOO) += foo.o

	$(CONFIG_FOO) evaluates to either y (for built-in) or m (for module).
	If CONFIG_FOO is neither y nor m, then the file will not be compiled
	nor linked.

--- 3.2 Built-in object goals - obj-y

	The kbuild Makefile specifies object files for vmlinux
	in the $(obj-y) lists.  These lists depend on the kernel
	configuration.

	Kbuild compiles all the $(obj-y) files.  It then calls
	"$(LD) -r" to merge these files into one built-in.o file.
	built-in.o is later linked into vmlinux by the parent Makefile.

	The order of files in $(obj-y) is significant.  Duplicates in
	the lists are allowed: the first instance will be linked into
	built-in.o and succeeding instances will be ignored.

	Link order is significant, because certain functions
	(module_init() / __initcall) will be called during boot in the
	order they appear. So keep in mind that changing the link
	order may e.g. change the order in which your SCSI
	controllers are detected, and thus your disks are renumbered.

	Example:
		#drivers/isdn/i4l/Makefile
		# Makefile for the kernel ISDN subsystem and device drivers.
		# Each configuration option enables a list of files.
		obj-$(CONFIG_ISDN_I4L)         += isdn.o
		obj-$(CONFIG_ISDN_PPP_BSDCOMP) += isdn_bsdcomp.o

--- 3.3 Loadable module goals - obj-m

	$(obj-m) specifies object files which are built as loadable
	kernel modules.

	A module may be built from one source file or several source
	files. In the case of one source file, the kbuild makefile
	simply adds the file to $(obj-m).

	Example:
		#drivers/isdn/i4l/Makefile
		obj-$(CONFIG_ISDN_PPP_BSDCOMP) += isdn_bsdcomp.o

	Note: In this example $(CONFIG_ISDN_PPP_BSDCOMP) evaluates to 'm'

	If a kernel module is built from several source files, you specify
	that you want to build a module in the same way as above; however,
	kbuild needs to know which object files you want to build your
	module from, so you have to tell it by setting a $(<module_name>-y)
	variable.

	Example:
		#drivers/isdn/i4l/Makefile
		obj-$(CONFIG_ISDN_I4L) += isdn.o
		isdn-y := isdn_net_lib.o isdn_v110.o isdn_common.o

	In this example, the module name will be isdn.o. Kbuild will
	compile the objects listed in $(isdn-y) and then run
	"$(LD) -r" on the list of these files to generate isdn.o.

	Due to kbuild recognizing $(<module_name>-y) for composite objects,
	you can use the value of a CONFIG_ symbol to optionally include an
	object file as part of a composite object.

	Example:
		#fs/ext2/Makefile
	        obj-$(CONFIG_EXT2_FS) += ext2.o
		ext2-y := balloc.o dir.o file.o ialloc.o inode.o ioctl.o \
			  namei.o super.o symlink.o
	        ext2-$(CONFIG_EXT2_FS_XATTR) += xattr.o xattr_user.o \
						xattr_trusted.o

	In this example, xattr.o, xattr_user.o and xattr_trusted.o are only
	part of the composite object ext2.o if $(CONFIG_EXT2_FS_XATTR)
	evaluates to 'y'.

	Note: Of course, when you are building objects into the kernel,
	the syntax above will also work. So, if you have CONFIG_EXT2_FS=y,
	kbuild will build an ext2.o file for you out of the individual
	parts and then link this into built-in.o, as you would expect.

--- 3.4 Objects which export symbols

	No special notation is required in the makefiles for
	modules exporting symbols.

--- 3.5 Library file goals - lib-y

	Objects listed with obj-* are used for modules, or
	combined in a built-in.o for that specific directory.
	There is also the possibility to list objects that will
	be included in a library, lib.a.
	All objects listed with lib-y are combined in a single
	library for that directory.
	Objects that are listed in obj-y and additionally listed in
	lib-y will not be included in the library, since they will
	be accessible anyway.
	For consistency, objects listed in lib-m will be included in lib.a.

	Note that the same kbuild makefile may list files to be built-in
	and to be part of a library. Therefore the same directory
	may contain both a built-in.o and a lib.a file.

	Example:
		#arch/x86/lib/Makefile
		lib-y    := delay.o

	This will create a library lib.a based on delay.o. For kbuild to
	actually recognize that there is a lib.a being built, the directory
	shall be listed in libs-y.
	See also "6.4 List directories to visit when descending".

	Use of lib-y is normally restricted to lib/ and arch/*/lib.

--- 3.6 Descending down in directories

	A Makefile is only responsible for building objects in its own
	directory. Files in subdirectories should be taken care of by
	Makefiles in these subdirs. The build system will automatically
	invoke make recursively in subdirectories, provided you let it know of
	them.

	To do so, obj-y and obj-m are used.
	ext2 lives in a separate directory, and the Makefile present in fs/
	tells kbuild to descend down using the following assignment.

	Example:
		#fs/Makefile
		obj-$(CONFIG_EXT2_FS) += ext2/

	If CONFIG_EXT2_FS is set to either 'y' (built-in) or 'm' (modular)
	the corresponding obj- variable will be set, and kbuild will descend
	down in the ext2 directory.
	Kbuild only uses this information to decide that it needs to visit
	the directory, it is the Makefile in the subdirectory that
	specifies what is modular and what is built-in.

	It is good practice to use a CONFIG_ variable when assigning directory
	names. This allows kbuild to totally skip the directory if the
	corresponding CONFIG_ option is neither 'y' nor 'm'.

--- 3.7 Compilation flags

    ccflags-y, asflags-y and ldflags-y
	These three flags apply only to the kbuild makefile in which they
	are assigned. They are used for all the normal cc, as and ld
	invocations happening during a recursive build.
	Note: Flags with the same behaviour were previously named:
	EXTRA_CFLAGS, EXTRA_AFLAGS and EXTRA_LDFLAGS.
	They are still supported but their usage is deprecated.

	ccflags-y specifies options for compiling with $(CC).

	Example:
		# drivers/acpi/Makefile
		ccflags-y := -Os
		ccflags-$(CONFIG_ACPI_DEBUG) += -DACPI_DEBUG_OUTPUT

	This variable is necessary because the top Makefile owns the
	variable $(KBUILD_CFLAGS) and uses it for compilation flags for the
	entire tree.

	asflags-y specifies options for assembling with $(AS).

	Example:
		#arch/sparc/kernel/Makefile
		asflags-y := -ansi

	ldflags-y specifies options for linking with $(LD).

	Example:
		#arch/cris/boot/compressed/Makefile
		ldflags-y += -T $(srctree)/$(src)/decompress_$(arch-y).lds

    subdir-ccflags-y, subdir-asflags-y
	The two flags listed above are similar to ccflags-y and asflags-y.
	The difference is that the subdir- variants have effect for the kbuild
	file where they are present and all subdirectories.
	Options specified using subdir-* are added to the commandline before
	the options specified using the non-subdir variants.

	Example:
		subdir-ccflags-y := -Werror

    CFLAGS_$@, AFLAGS_$@

	CFLAGS_$@ and AFLAGS_$@ only apply to commands in current
	kbuild makefile.

	$(CFLAGS_$@) specifies per-file options for $(CC).  The $@
	part has a literal value which specifies the file that it is for.

	Example:
		# drivers/scsi/Makefile
		CFLAGS_aha152x.o =   -DAHA152X_STAT -DAUTOCONF
		CFLAGS_gdth.o    = # -DDEBUG_GDTH=2 -D__SERIAL__ -D__COM2__ \
				     -DGDTH_STATISTICS

	These two lines specify compilation flags for aha152x.o and gdth.o.

	$(AFLAGS_$@) is a similar feature for source files in assembly
	languages.

	Example:
		# arch/arm/kernel/Makefile
		AFLAGS_head.o        := -DTEXT_OFFSET=$(TEXT_OFFSET)
		AFLAGS_crunch-bits.o := -Wa,-mcpu=ep9312
		AFLAGS_iwmmxt.o      := -Wa,-mcpu=iwmmxt


--- 3.9 Dependency tracking

	Kbuild tracks dependencies on the following:
	1) All prerequisite files (both *.c and *.h)
	2) CONFIG_ options used in all prerequisite files
	3) Command-line used to compile target

	Thus, if you change an option to $(CC) all affected files will
	be re-compiled.

--- 3.10 Special Rules

	Special rules are used when the kbuild infrastructure does
	not provide the required support. A typical example is
	header files generated during the build process.
	Another example are the architecture-specific Makefiles which
	need special rules to prepare boot images etc.

	Special rules are written as normal Make rules.
	Kbuild is not executing in the directory where the Makefile is
	located, so all special rules shall provide a relative
	path to prerequisite files and target files.

	Two variables are used when defining special rules:

    $(src)
	$(src) is a relative path which points to the directory
	where the Makefile is located. Always use $(src) when
	referring to files located in the src tree.

    $(obj)
	$(obj) is a relative path which points to the directory
	where the target is saved. Always use $(obj) when
	referring to generated files.

	Example:
		#drivers/scsi/Makefile
		$(obj)/53c8xx_d.h: $(src)/53c7,8xx.scr $(src)/script_asm.pl
			$(CPP) -DCHIP=810 - < $< | ... $(src)/script_asm.pl

	This is a special rule, following the normal syntax
	required by make.
	The target file depends on two prerequisite files. References
	to the target file are prefixed with $(obj), references
	to prerequisites are referenced with $(src) (because they are not
	generated files).

    $(kecho)
	echoing information to user in a rule is often a good practice
	but when execution "make -s" one does not expect to see any output
	except for warnings/errors.
	To support this kbuild defines $(kecho) which will echo out the
	text following $(kecho) to stdout except if "make -s" is used.

	Example:
		#arch/blackfin/boot/Makefile
		$(obj)/vmImage: $(obj)/vmlinux.gz
			$(call if_changed,uimage)
			@$(kecho) 'Kernel: $@ is ready'


--- 3.11 $(CC) support functions

	The kernel may be built with several different versions of
	$(CC), each supporting a unique set of features and options.
	kbuild provides basic support to check for valid options for $(CC).
	$(CC) is usually the gcc compiler, but other alternatives are
	available.

    as-option
	as-option is used to check if $(CC) -- when used to compile
	assembler (*.S) files -- supports the given option. An optional
	second option may be specified if the first option is not supported.

	Example:
		#arch/sh/Makefile
		cflags-y += $(call as-option,-Wa$(comma)-isa=$(isa-y),)

	In the above example, cflags-y will be assigned the option
	-Wa$(comma)-isa=$(isa-y) if it is supported by $(CC).
	The second argument is optional, and if supplied will be used
	if first argument is not supported.

    cc-ldoption
	cc-ldoption is used to check if $(CC) when used to link object files
	supports the given option.  An optional second option may be
	specified if first option are not supported.

	Example:
		#arch/x86/kernel/Makefile
		vsyscall-flags += $(call cc-ldoption, -Wl$(comma)--hash-style=sysv)

	In the above example, vsyscall-flags will be assigned the option
	-Wl$(comma)--hash-style=sysv if it is supported by $(CC).
	The second argument is optional, and if supplied will be used
	if first argument is not supported.

    as-instr
	as-instr checks if the assembler reports a specific instruction
	and then outputs either option1 or option2
	C escapes are supported in the test instruction
	Note: as-instr-option uses KBUILD_AFLAGS for $(AS) options

    cc-option
	cc-option is used to check if $(CC) supports a given option, and if
	not supported to use an optional second option.

	Example:
		#arch/x86/Makefile
		cflags-y += $(call cc-option,-march=pentium-mmx,-march=i586)

	In the above example, cflags-y will be assigned the option
	-march=pentium-mmx if supported by $(CC), otherwise -march=i586.
	The second argument to cc-option is optional, and if omitted,
	cflags-y will be assigned no value if first option is not supported.
	Note: cc-option uses KBUILD_CFLAGS for $(CC) options

   cc-option-yn
	cc-option-yn is used to check if gcc supports a given option
	and return 'y' if supported, otherwise 'n'.

	Example:
		#arch/ppc/Makefile
		biarch := $(call cc-option-yn, -m32)
		aflags-$(biarch) += -a32
		cflags-$(biarch) += -m32

	In the above example, $(biarch) is set to y if $(CC) supports the -m32
	option. When $(biarch) equals 'y', the expanded variables $(aflags-y)
	and $(cflags-y) will be assigned the values -a32 and -m32,
	respectively.
	Note: cc-option-yn uses KBUILD_CFLAGS for $(CC) options

    cc-disable-warning
	cc-disable-warning checks if gcc supports a given warning and returns
	the commandline switch to disable it. This special function is needed,
	because gcc 4.4 and later accept any unknown -Wno-* option and only
	warn about it if there is another warning in the source file.

	Example:
		KBUILD_CFLAGS += $(call cc-disable-warning, unused-but-set-variable)

	In the above example, -Wno-unused-but-set-variable will be added to
	KBUILD_CFLAGS only if gcc really accepts it.

    cc-version
	cc-version returns a numerical version of the $(CC) compiler version.
	The format is <major><minor> where both are two digits. So for example
	gcc 3.41 would return 0341.
	cc-version is useful when a specific $(CC) version is faulty in one
	area, for example -mregparm=3 was broken in some gcc versions
	even though the option was accepted by gcc.

	Example:
		#arch/x86/Makefile
		cflags-y += $(shell \
		if [ $(cc-version) -ge 0300 ] ; then \
			echo "-mregparm=3"; fi ;)

	In the above example, -mregparm=3 is only used for gcc version greater
	than or equal to gcc 3.0.

    cc-ifversion
	cc-ifversion tests the version of $(CC) and equals the fourth parameter
	if version expression is true, or the fifth (if given) if the version
	expression is false.

	Example:
		#fs/reiserfs/Makefile
		ccflags-y := $(call cc-ifversion, -lt, 0402, -O1)

	In this example, ccflags-y will be assigned the value -O1 if the
	$(CC) version is less than 4.2.
	cc-ifversion takes all the shell operators:
	-eq, -ne, -lt, -le, -gt, and -ge
	The third parameter may be a text as in this example, but it may also
	be an expanded variable or a macro.

    cc-fullversion
	cc-fullversion is useful when the exact version of gcc is needed.
	One typical use-case is when a specific GCC version is broken.
	cc-fullversion points out a more specific version than cc-version does.

	Example:
		#arch/powerpc/Makefile
		$(Q)if test "$(cc-fullversion)" = "040200" ; then \
			echo -n '*** GCC-4.2.0 cannot compile the 64-bit powerpc ' ; \
			false ; \
		fi

	In this example for a specific GCC version the build will error out
	explaining to the user why it stops.

    cc-cross-prefix
	cc-cross-prefix is used to check if there exists a $(CC) in path with
	one of the listed prefixes. The first prefix where there exist a
	prefix$(CC) in the PATH is returned - and if no prefix$(CC) is found
	then nothing is returned.
	Additional prefixes are separated by a single space in the
	call of cc-cross-prefix.
	This functionality is useful for architecture Makefiles that try
	to set CROSS_COMPILE to well-known values but may have several
	values to select between.
	It is recommended only to try to set CROSS_COMPILE if it is a cross
	build (host arch is different from target arch). And if CROSS_COMPILE
	is already set then leave it with the old value.

	Example:
		#arch/m68k/Makefile
		ifneq ($(SUBARCH),$(ARCH))
		        ifeq ($(CROSS_COMPILE),)
		               CROSS_COMPILE := $(call cc-cross-prefix, m68k-linux-gnu-)
			endif
		endif

--- 3.12 $(LD) support functions

    ld-option
	ld-option is used to check if $(LD) supports the supplied option.
	ld-option takes two options as arguments.
	The second argument is an optional option that can be used if the
	first option is not supported by $(LD).

	Example:
		#Makefile
		LDFLAGS_vmlinux += $(call ld-option, -X)


=== 4 Host Program support

Kbuild supports building executables on the host for use during the
compilation stage.
Two steps are required in order to use a host executable.

The first step is to tell kbuild that a host program exists. This is
done utilising the variable hostprogs-y.

The second step is to add an explicit dependency to the executable.
This can be done in two ways. Either add the dependency in a rule,
or utilise the variable $(always).
Both possibilities are described in the following.

--- 4.1 Simple Host Program

	In some cases there is a need to compile and run a program on the
	computer where the build is running.
	The following line tells kbuild that the program bin2hex shall be
	built on the build host.

	Example:
		hostprogs-y := bin2hex

	Kbuild assumes in the above example that bin2hex is made from a single
	c-source file named bin2hex.c located in the same directory as
	the Makefile.

--- 4.2 Composite Host Programs

	Host programs can be made up based on composite objects.
	The syntax used to define composite objects for host programs is
	similar to the syntax used for kernel objects.
	$(<executable>-objs) lists all objects used to link the final
	executable.

	Example:
		#scripts/lxdialog/Makefile
		hostprogs-y   := lxdialog
		lxdialog-objs := checklist.o lxdialog.o

	Objects with extension .o are compiled from the corresponding .c
	files. In the above example, checklist.c is compiled to checklist.o
	and lxdialog.c is compiled to lxdialog.o.
	Finally, the two .o files are linked to the executable, lxdialog.
	Note: The syntax <executable>-y is not permitted for host-programs.

--- 4.3 Using C++ for host programs

	kbuild offers support for host programs written in C++. This was
	introduced solely to support kconfig, and is not recommended
	for general use.

	Example:
		#scripts/kconfig/Makefile
		hostprogs-y   := qconf
		qconf-cxxobjs := qconf.o

	In the example above the executable is composed of the C++ file
	qconf.cc - identified by $(qconf-cxxobjs).

	If qconf is composed of a mixture of .c and .cc files, then an
	additional line can be used to identify this.

	Example:
		#scripts/kconfig/Makefile
		hostprogs-y   := qconf
		qconf-cxxobjs := qconf.o
		qconf-objs    := check.o

--- 4.4 Controlling compiler options for host programs

	When compiling host programs, it is possible to set specific flags.
	The programs will always be compiled utilising $(HOSTCC) passed
	the options specified in $(HOSTCFLAGS).
	To set flags that will take effect for all host programs created
	in that Makefile, use the variable HOST_EXTRACFLAGS.

	Example:
		#scripts/lxdialog/Makefile
		HOST_EXTRACFLAGS += -I/usr/include/ncurses

	To set specific flags for a single file the following construction
	is used:

	Example:
		#arch/ppc64/boot/Makefile
		HOSTCFLAGS_piggyback.o := -DKERNELBASE=$(KERNELBASE)

	It is also possible to specify additional options to the linker.

	Example:
		#scripts/kconfig/Makefile
		HOSTLOADLIBES_qconf := -L$(QTDIR)/lib

	When linking qconf, it will be passed the extra option
	"-L$(QTDIR)/lib".

--- 4.5 When host programs are actually built

	Kbuild will only build host-programs when they are referenced
	as a prerequisite.
	This is possible in two ways:

	(1) List the prerequisite explicitly in a special rule.

	Example:
		#drivers/pci/Makefile
		hostprogs-y := gen-devlist
		$(obj)/devlist.h: $(src)/pci.ids $(obj)/gen-devlist
			( cd $(obj); ./gen-devlist ) < $<

	The target $(obj)/devlist.h will not be built before
	$(obj)/gen-devlist is updated. Note that references to
	the host programs in special rules must be prefixed with $(obj).

	(2) Use $(always)
	When there is no suitable special rule, and the host program
	shall be built when a makefile is entered, the $(always)
	variable shall be used.

	Example:
		#scripts/lxdialog/Makefile
		hostprogs-y   := lxdialog
		always        := $(hostprogs-y)

	This will tell kbuild to build lxdialog even if not referenced in
	any rule.

--- 4.6 Using hostprogs-$(CONFIG_FOO)

	A typical pattern in a Kbuild file looks like this:

	Example:
		#scripts/Makefile
		hostprogs-$(CONFIG_KALLSYMS) += kallsyms

	Kbuild knows about both 'y' for built-in and 'm' for module.
	So if a config symbol evaluates to 'm', kbuild will still build
	the binary. In other words, Kbuild handles hostprogs-m exactly
	like hostprogs-y. But only hostprogs-y is recommended to be used
	when no CONFIG symbols are involved.

=== 5 Kbuild clean infrastructure

"make clean" deletes most generated files in the obj tree where the kernel
is compiled. This includes generated files such as host programs.
Kbuild knows targets listed in $(hostprogs-y), $(hostprogs-m), $(always),
$(extra-y) and $(targets). They are all deleted during "make clean".
Files matching the patterns "*.[oas]", "*.ko", plus some additional files
generated by kbuild are deleted all over the kernel src tree when
"make clean" is executed.

Additional files can be specified in kbuild makefiles by use of $(clean-files).

	Example:
		#lib/Makefile
		clean-files := crc32table.h

When executing "make clean", the file "crc32table.h" will be deleted.
Kbuild will assume files to be in the same relative directory as the
Makefile, except if prefixed with $(objtree).

To delete a directory hierarchy use:

	Example:
		#scripts/package/Makefile
		clean-dirs := $(objtree)/debian/

This will delete the directory debian in the toplevel directory, including all
subdirectories.

To exclude certain files from make clean, use the $(no-clean-files) variable.
This is only a special case used in the top level Kbuild file:

	Example:
		#Kbuild
		no-clean-files := $(bounds-file) $(offsets-file)

Usually kbuild descends down in subdirectories due to "obj-* := dir/",
but in the architecture makefiles where the kbuild infrastructure
is not sufficient this sometimes needs to be explicit.

	Example:
		#arch/x86/boot/Makefile
		subdir- := compressed/

The above assignment instructs kbuild to descend down in the
directory compressed/ when "make clean" is executed.

To support the clean infrastructure in the Makefiles that build the
final bootimage there is an optional target named archclean:

	Example:
		#arch/x86/Makefile
		archclean:
			$(Q)$(MAKE) $(clean)=arch/x86/boot

When "make clean" is executed, make will descend down in arch/x86/boot,
and clean as usual. The Makefile located in arch/x86/boot/ may use
the subdir- trick to descend further down.

Note 1: arch/$(ARCH)/Makefile cannot use "subdir-", because that file is
included in the top level makefile, and the kbuild infrastructure
is not operational at that point.

Note 2: All directories listed in core-y, libs-y, drivers-y and net-y will
be visited during "make clean".

=== 6 Architecture Makefiles

The top level Makefile sets up the environment and does the preparation,
before starting to descend down in the individual directories.
The top level makefile contains the generic part, whereas
arch/$(ARCH)/Makefile contains what is required to set up kbuild
for said architecture.
To do so, arch/$(ARCH)/Makefile sets up a number of variables and defines
a few targets.

When kbuild executes, the following steps are followed (roughly):
1) Configuration of the kernel => produce .config
2) Store kernel version in include/linux/version.h
3) Updating all other prerequisites to the target prepare:
   - Additional prerequisites are specified in arch/$(ARCH)/Makefile
4) Recursively descend down in all directories listed in
   init-* core* drivers-* net-* libs-* and build all targets.
   - The values of the above variables are expanded in arch/$(ARCH)/Makefile.
5) All object files are then linked and the resulting file vmlinux is
   located at the root of the obj tree.
   The very first objects linked are listed in head-y, assigned by
   arch/$(ARCH)/Makefile.
6) Finally, the architecture-specific part does any required post processing
   and builds the final bootimage.
   - This includes building boot records
   - Preparing initrd images and the like


--- 6.1 Set variables to tweak the build to the architecture

    LDFLAGS		Generic $(LD) options

	Flags used for all invocations of the linker.
	Often specifying the emulation is sufficient.

	Example:
		#arch/s390/Makefile
		LDFLAGS         := -m elf_s390
	Note: ldflags-y can be used to further customise
	the flags used. See chapter 3.7.

    LDFLAGS_MODULE	Options for $(LD) when linking modules

	LDFLAGS_MODULE is used to set specific flags for $(LD) when
	linking the .ko files used for modules.
	Default is "-r", for relocatable output.

    LDFLAGS_vmlinux	Options for $(LD) when linking vmlinux

	LDFLAGS_vmlinux is used to specify additional flags to pass to
	the linker when linking the final vmlinux image.
	LDFLAGS_vmlinux uses the LDFLAGS_$@ support.

	Example:
		#arch/x86/Makefile
		LDFLAGS_vmlinux := -e stext

    OBJCOPYFLAGS	objcopy flags

	When $(call if_changed,objcopy) is used to translate a .o file,
	the flags specified in OBJCOPYFLAGS will be used.
	$(call if_changed,objcopy) is often used to generate raw binaries on
	vmlinux.

	Example:
		#arch/s390/Makefile
		OBJCOPYFLAGS := -O binary

		#arch/s390/boot/Makefile
		$(obj)/image: vmlinux FORCE
			$(call if_changed,objcopy)

	In this example, the binary $(obj)/image is a binary version of
	vmlinux. The usage of $(call if_changed,xxx) will be described later.

    KBUILD_AFLAGS		$(AS) assembler flags

	Default value - see top level Makefile
	Append or modify as required per architecture.

	Example:
		#arch/sparc64/Makefile
		KBUILD_AFLAGS += -m64 -mcpu=ultrasparc

    KBUILD_CFLAGS		$(CC) compiler flags

	Default value - see top level Makefile
	Append or modify as required per architecture.

	Often, the KBUILD_CFLAGS variable depends on the configuration.

	Example:
		#arch/x86/boot/compressed/Makefile
		cflags-$(CONFIG_X86_32) := -march=i386
		cflags-$(CONFIG_X86_64) := -mcmodel=small
		KBUILD_CFLAGS += $(cflags-y)

	Many arch Makefiles dynamically run the target C compiler to
	probe supported options:

		#arch/x86/Makefile

		...
		cflags-$(CONFIG_MPENTIUMII)     += $(call cc-option,\
						-march=pentium2,-march=i686)
		...
		# Disable unit-at-a-time mode ...
		KBUILD_CFLAGS += $(call cc-option,-fno-unit-at-a-time)
		...


	The first example utilises the trick that a config option expands
	to 'y' when selected.

    KBUILD_AFLAGS_KERNEL	$(AS) options specific for built-in

	$(KBUILD_AFLAGS_KERNEL) contains extra C compiler flags used to compile
	resident kernel code.

    KBUILD_AFLAGS_MODULE   Options for $(AS) when building modules

	$(KBUILD_AFLAGS_MODULE) is used to add arch-specific options that
	are used for $(AS).
	From commandline AFLAGS_MODULE shall be used (see kbuild.txt).

    KBUILD_CFLAGS_KERNEL	$(CC) options specific for built-in

	$(KBUILD_CFLAGS_KERNEL) contains extra C compiler flags used to compile
	resident kernel code.

    KBUILD_CFLAGS_MODULE   Options for $(CC) when building modules

	$(KBUILD_CFLAGS_MODULE) is used to add arch-specific options that
	are used for $(CC).
	From commandline CFLAGS_MODULE shall be used (see kbuild.txt).

    KBUILD_LDFLAGS_MODULE   Options for $(LD) when linking modules

	$(KBUILD_LDFLAGS_MODULE) is used to add arch-specific options
	used when linking modules. This is often a linker script.
	From commandline LDFLAGS_MODULE shall be used (see kbuild.txt).

    KBUILD_ARFLAGS   Options for $(AR) when creating archives

	$(KBUILD_ARFLAGS) set by the top level Makefile to "D" (deterministic
	mode) if this option is supported by $(AR).

    ARCH_CPPFLAGS, ARCH_AFLAGS, ARCH_CFLAGS   Overrides the kbuild defaults

	These variables are appended to the KBUILD_CPPFLAGS,
	KBUILD_AFLAGS, and KBUILD_CFLAGS, respectively, after the
	top-level Makefile has set any other flags. This provides a
	means for an architecture to override the defaults.


--- 6.2 Add prerequisites to archheaders:

	The archheaders: rule is used to generate header files that
	may be installed into user space by "make header_install" or
	"make headers_install_all".  In order to support
	"make headers_install_all", this target has to be able to run
	on an unconfigured tree, or a tree configured for another
	architecture.

	It is run before "make archprepare" when run on the
	architecture itself.


--- 6.3 Add prerequisites to archprepare:

	The archprepare: rule is used to list prerequisites that need to be
	built before starting to descend down in the subdirectories.
	This is usually used for header files containing assembler constants.

		Example:
		#arch/arm/Makefile
		archprepare: maketools

	In this example, the file target maketools will be processed
	before descending down in the subdirectories.
	See also chapter XXX-TODO that describe how kbuild supports
	generating offset header files.


--- 6.4 List directories to visit when descending

	An arch Makefile cooperates with the top Makefile to define variables
	which specify how to build the vmlinux file.  Note that there is no
	corresponding arch-specific section for modules; the module-building
	machinery is all architecture-independent.


    head-y, init-y, core-y, libs-y, drivers-y, net-y

	$(head-y) lists objects to be linked first in vmlinux.
	$(libs-y) lists directories where a lib.a archive can be located.
	The rest list directories where a built-in.o object file can be
	located.

	$(init-y) objects will be located after $(head-y).
	Then the rest follows in this order:
	$(core-y), $(libs-y), $(drivers-y) and $(net-y).

	The top level Makefile defines values for all generic directories,
	and arch/$(ARCH)/Makefile only adds architecture-specific directories.

	Example:
		#arch/sparc64/Makefile
		core-y += arch/sparc64/kernel/
		libs-y += arch/sparc64/prom/ arch/sparc64/lib/
		drivers-$(CONFIG_OPROFILE)  += arch/sparc64/oprofile/


--- 6.5 Architecture-specific boot images

	An arch Makefile specifies goals that take the vmlinux file, compress
	it, wrap it in bootstrapping code, and copy the resulting files
	somewhere. This includes various kinds of installation commands.
	The actual goals are not standardized across architectures.

	It is common to locate any additional processing in a boot/
	directory below arch/$(ARCH)/.

	Kbuild does not provide any smart way to support building a
	target specified in boot/. Therefore arch/$(ARCH)/Makefile shall
	call make manually to build a target in boot/.

	The recommended approach is to include shortcuts in
	arch/$(ARCH)/Makefile, and use the full path when calling down
	into the arch/$(ARCH)/boot/Makefile.

	Example:
		#arch/x86/Makefile
		boot := arch/x86/boot
		bzImage: vmlinux
			$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@

	"$(Q)$(MAKE) $(build)=<dir>" is the recommended way to invoke
	make in a subdirectory.

	There are no rules for naming architecture-specific targets,
	but executing "make help" will list all relevant targets.
	To support this, $(archhelp) must be defined.

	Example:
		#arch/x86/Makefile
		define archhelp
		  echo  '* bzImage      - Image (arch/$(ARCH)/boot/bzImage)'
		endif

	When make is executed without arguments, the first goal encountered
	will be built. In the top level Makefile the first goal present
	is all:.
	An architecture shall always, per default, build a bootable image.
	In "make help", the default goal is highlighted with a '*'.
	Add a new prerequisite to all: to select a default goal different
	from vmlinux.

	Example:
		#arch/x86/Makefile
		all: bzImage

	When "make" is executed without arguments, bzImage will be built.

--- 6.6 Building non-kbuild targets

    extra-y

	extra-y specifies additional targets created in the current
	directory, in addition to any targets specified by obj-*.

	Listing all targets in extra-y is required for two purposes:
	1) Enable kbuild to check changes in command lines
	   - When $(call if_changed,xxx) is used
	2) kbuild knows what files to delete during "make clean"

	Example:
		#arch/x86/kernel/Makefile
		extra-y := head.o init_task.o

	In this example, extra-y is used to list object files that
	shall be built, but shall not be linked as part of built-in.o.


--- 6.7 Commands useful for building a boot image

	Kbuild provides a few macros that are useful when building a
	boot image.

    if_changed

	if_changed is the infrastructure used for the following commands.

	Usage:
		target: source(s) FORCE
			$(call if_changed,ld/objcopy/gzip/...)

	When the rule is evaluated, it is checked to see if any files
	need an update, or the command line has changed since the last
	invocation. The latter will force a rebuild if any options
	to the executable have changed.
	Any target that utilises if_changed must be listed in $(targets),
	otherwise the command line check will fail, and the target will
	always be built.
	Assignments to $(targets) are without $(obj)/ prefix.
	if_changed may be used in conjunction with custom commands as
	defined in 6.8 "Custom kbuild commands".

	Note: It is a typical mistake to forget the FORCE prerequisite.
	Another common pitfall is that whitespace is sometimes
	significant; for instance, the below will fail (note the extra space
	after the comma):
		target: source(s) FORCE
	#WRONG!#	$(call if_changed, ld/objcopy/gzip/...)

    ld
	Link target. Often, LDFLAGS_$@ is used to set specific options to ld.

    objcopy
	Copy binary. Uses OBJCOPYFLAGS usually specified in
	arch/$(ARCH)/Makefile.
	OBJCOPYFLAGS_$@ may be used to set additional options.

    gzip
	Compress target. Use maximum compression to compress target.

	Example:
		#arch/x86/boot/Makefile
		LDFLAGS_bootsect := -Ttext 0x0 -s --oformat binary
		LDFLAGS_setup    := -Ttext 0x0 -s --oformat binary -e begtext

		targets += setup setup.o bootsect bootsect.o
		$(obj)/setup $(obj)/bootsect: %: %.o FORCE
			$(call if_changed,ld)

	In this example, there are two possible targets, requiring different
	options to the linker. The linker options are specified using the
	LDFLAGS_$@ syntax - one for each potential target.
	$(targets) are assigned all potential targets, by which kbuild knows
	the targets and will:
		1) check for commandline changes
		2) delete target during make clean

	The ": %: %.o" part of the prerequisite is a shorthand that
	frees us from listing the setup.o and bootsect.o files.
	Note: It is a common mistake to forget the "targets :=" assignment,
	      resulting in the target file being recompiled for no
	      obvious reason.

    dtc
	Create flattened device tree blob object suitable for linking
	into vmlinux. Device tree blobs linked into vmlinux are placed
	in an init section in the image. Platform code *must* copy the
	blob to non-init memory prior to calling unflatten_device_tree().

	To use this command, simply add *.dtb into obj-y or targets, or make
	some other target depend on %.dtb

	A central rule exists to create $(obj)/%.dtb from $(src)/%.dts;
	architecture Makefiles do no need to explicitly write out that rule.

	Example:
		targets += $(dtb-y)
		clean-files += *.dtb
		DTC_FLAGS ?= -p 1024

--- 6.8 Custom kbuild commands

	When kbuild is executing with KBUILD_VERBOSE=0, then only a shorthand
	of a command is normally displayed.
	To enable this behaviour for custom commands kbuild requires
	two variables to be set:
	quiet_cmd_<command>	- what shall be echoed
	      cmd_<command>	- the command to execute

	Example:
		#
		quiet_cmd_image = BUILD   $@
		      cmd_image = $(obj)/tools/build $(BUILDFLAGS) \
		                                     $(obj)/vmlinux.bin > $@

		targets += bzImage
		$(obj)/bzImage: $(obj)/vmlinux.bin $(obj)/tools/build FORCE
			$(call if_changed,image)
			@echo 'Kernel: $@ is ready'

	When updating the $(obj)/bzImage target, the line

	BUILD    arch/x86/boot/bzImage

	will be displayed with "make KBUILD_VERBOSE=0".


--- 6.9 Preprocessing linker scripts

	When the vmlinux image is built, the linker script
	arch/$(ARCH)/kernel/vmlinux.lds is used.
	The script is a preprocessed variant of the file vmlinux.lds.S
	located in the same directory.
	kbuild knows .lds files and includes a rule *lds.S -> *lds.

	Example:
		#arch/x86/kernel/Makefile
		always := vmlinux.lds

		#Makefile
		export CPPFLAGS_vmlinux.lds += -P -C -U$(ARCH)

	The assignment to $(always) is used to tell kbuild to build the
	target vmlinux.lds.
	The assignment to $(CPPFLAGS_vmlinux.lds) tells kbuild to use the
	specified options when building the target vmlinux.lds.

	When building the *.lds target, kbuild uses the variables:
	KBUILD_CPPFLAGS	: Set in top-level Makefile
	cppflags-y	: May be set in the kbuild makefile
	CPPFLAGS_$(@F)  : Target-specific flags.
	                  Note that the full filename is used in this
	                  assignment.

	The kbuild infrastructure for *lds files is used in several
	architecture-specific files.

--- 6.10 Generic header files

	The directory include/asm-generic contains the header files
	that may be shared between individual architectures.
	The recommended approach how to use a generic header file is
	to list the file in the Kbuild file.
	See "7.3 generic-y" for further info on syntax etc.

--- 6.11 Post-link pass

	If the file arch/xxx/Makefile.postlink exists, this makefile
	will be invoked for post-link objects (vmlinux and modules.ko)
	for architectures to run post-link passes on. Must also handle
	the clean target.

	This pass runs after kallsyms generation. If the architecture
	needs to modify symbol locations, rather than manipulate the
	kallsyms, it may be easier to add another postlink target for
	.tmp_vmlinux? targets to be called from link-vmlinux.sh.

	For example, powerpc uses this to check relocation sanity of
	the linked vmlinux file.

=== 7 Kbuild syntax for exported headers

The kernel includes a set of headers that is exported to userspace.
Many headers can be exported as-is but other headers require a
minimal pre-processing before they are ready for user-space.
The pre-processing does:
- drop kernel-specific annotations
- drop include of compiler.h
- drop all sections that are kernel internal (guarded by ifdef __KERNEL__)

All headers under include/uapi/, include/generated/uapi/,
arch/<arch>/include/uapi/ and arch/<arch>/include/generated/uapi/
are exported.

A Kbuild file may be defined under arch/<arch>/include/uapi/asm/ and
arch/<arch>/include/asm/ to list asm files coming from asm-generic.
See subsequent chapter for the syntax of the Kbuild file.

	--- 7.1 no-export-headers

	no-export-headers is essentially used by include/uapi/linux/Kbuild to
	avoid exporting specific headers (e.g. kvm.h) on architectures that do
	not support it. It should be avoided as much as possible.

	--- 7.2 generic-y

	If an architecture uses a verbatim copy of a header from
	include/asm-generic then this is listed in the file
	arch/$(ARCH)/include/asm/Kbuild like this:

		Example:
			#arch/x86/include/asm/Kbuild
			generic-y += termios.h
			generic-y += rtc.h

	During the prepare phase of the build a wrapper include
	file is generated in the directory:

		arch/$(ARCH)/include/generated/asm

	When a header is exported where the architecture uses
	the generic header a similar wrapper is generated as part
	of the set of exported headers in the directory:

		usr/include/asm

	The generated wrapper will in both cases look like the following:

		Example: termios.h
			#include <asm-generic/termios.h>

	--- 7.3 generated-y

	If an architecture generates other header files alongside generic-y
	wrappers, generated-y specifies them.

	This prevents them being treated as stale asm-generic wrappers and
	removed.

		Example:
			#arch/x86/include/asm/Kbuild
			generated-y += syscalls_32.h

	--- 7.5 mandatory-y

	mandatory-y is essentially used by include/uapi/asm-generic/Kbuild.asm
	to define the minimum set of headers that must be exported in
	include/asm.

	The convention is to list one subdir per line and
	preferably in alphabetic order.

=== 8 Kbuild Variables

The top Makefile exports the following variables:

    VERSION, PATCHLEVEL, SUBLEVEL, EXTRAVERSION

	These variables define the current kernel version.  A few arch
	Makefiles actually use these values directly; they should use
	$(KERNELRELEASE) instead.

	$(VERSION), $(PATCHLEVEL), and $(SUBLEVEL) define the basic
	three-part version number, such as "2", "4", and "0".  These three
	values are always numeric.

	$(EXTRAVERSION) defines an even tinier sublevel for pre-patches
	or additional patches.	It is usually some non-numeric string
	such as "-pre4", and is often blank.

    KERNELRELEASE

	$(KERNELRELEASE) is a single string such as "2.4.0-pre4", suitable
	for constructing installation directory names or showing in
	version strings.  Some arch Makefiles use it for this purpose.

    ARCH

	This variable defines the target architecture, such as "i386",
	"arm", or "sparc". Some kbuild Makefiles test $(ARCH) to
	determine which files to compile.

	By default, the top Makefile sets $(ARCH) to be the same as the
	host system architecture.  For a cross build, a user may
	override the value of $(ARCH) on the command line:

	    make ARCH=m68k ...


    INSTALL_PATH

	This variable defines a place for the arch Makefiles to install
	the resident kernel image and System.map file.
	Use this for architecture-specific install targets.

    INSTALL_MOD_PATH, MODLIB

	$(INSTALL_MOD_PATH) specifies a prefix to $(MODLIB) for module
	installation.  This variable is not defined in the Makefile but
	may be passed in by the user if desired.

	$(MODLIB) specifies the directory for module installation.
	The top Makefile defines $(MODLIB) to
	$(INSTALL_MOD_PATH)/lib/modules/$(KERNELRELEASE).  The user may
	override this value on the command line if desired.

    INSTALL_MOD_STRIP

	If this variable is specified, it will cause modules to be stripped
	after they are installed.  If INSTALL_MOD_STRIP is '1', then the
	default option --strip-debug will be used.  Otherwise, the
	INSTALL_MOD_STRIP value will be used as the option(s) to the strip
	command.


=== 9 Makefile language

The kernel Makefiles are designed to be run with GNU Make.  The Makefiles
use only the documented features of GNU Make, but they do use many
GNU extensions.

GNU Make supports elementary list-processing functions.  The kernel
Makefiles use a novel style of list building and manipulation with few
"if" statements.

GNU Make has two assignment operators, ":=" and "=".  ":=" performs
immediate evaluation of the right-hand side and stores an actual string
into the left-hand side.  "=" is like a formula definition; it stores the
right-hand side in an unevaluated form and then evaluates this form each
time the left-hand side is used.

There are some cases where "=" is appropriate.  Usually, though, ":="
is the right choice.

=== 10 Credits

Original version made by Michael Elizabeth Chastain, <mailto:mec@shout.net>
Updates by Kai Germaschewski <kai@tp1.ruhr-uni-bochum.de>
Updates by Sam Ravnborg <sam@ravnborg.org>
Language QA by Jan Engelhardt <jengelh@gmx.de>

=== 11 TODO

- Describe how kbuild supports shipped files with _shipped.
- Generating offset header files.
- Add more variables to section 7?