Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 1 | /* |
| 2 | * Copyright © 2010 Intel Corporation |
| 3 | * |
| 4 | * Permission is hereby granted, free of charge, to any person obtaining a |
| 5 | * copy of this software and associated documentation files (the "Software"), |
| 6 | * to deal in the Software without restriction, including without limitation |
| 7 | * the rights to use, copy, modify, merge, publish, distribute, sublicense, |
| 8 | * and/or sell copies of the Software, and to permit persons to whom the |
| 9 | * Software is furnished to do so, subject to the following conditions: |
| 10 | * |
| 11 | * The above copyright notice and this permission notice (including the next |
| 12 | * paragraph) shall be included in all copies or substantial portions of the |
| 13 | * Software. |
| 14 | * |
| 15 | * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR |
| 16 | * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, |
| 17 | * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL |
| 18 | * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER |
| 19 | * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING |
| 20 | * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER |
| 21 | * DEALINGS IN THE SOFTWARE. |
| 22 | * |
| 23 | * Authors: |
| 24 | * jim liu <jim.liu@intel.com> |
| 25 | * Jackie Li<yaodong.li@intel.com> |
| 26 | */ |
| 27 | |
| 28 | #include "mdfld_dsi_dpi.h" |
| 29 | #include "mdfld_output.h" |
| 30 | #include "mdfld_dsi_pkg_sender.h" |
| 31 | #include "psb_drv.h" |
| 32 | #include "tc35876x-dsi-lvds.h" |
| 33 | |
| 34 | static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output, |
| 35 | int pipe); |
| 36 | |
| 37 | static void mdfld_wait_for_HS_DATA_FIFO(struct drm_device *dev, u32 pipe) |
| 38 | { |
| 39 | u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe); |
| 40 | int timeout = 0; |
| 41 | |
| 42 | udelay(500); |
| 43 | |
| 44 | /* This will time out after approximately 2+ seconds */ |
| 45 | while ((timeout < 20000) && |
| 46 | (REG_READ(gen_fifo_stat_reg) & DSI_FIFO_GEN_HS_DATA_FULL)) { |
| 47 | udelay(100); |
| 48 | timeout++; |
| 49 | } |
| 50 | |
| 51 | if (timeout == 20000) |
| 52 | DRM_INFO("MIPI: HS Data FIFO was never cleared!\n"); |
| 53 | } |
| 54 | |
| 55 | static void mdfld_wait_for_HS_CTRL_FIFO(struct drm_device *dev, u32 pipe) |
| 56 | { |
| 57 | u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe); |
| 58 | int timeout = 0; |
| 59 | |
| 60 | udelay(500); |
| 61 | |
| 62 | /* This will time out after approximately 2+ seconds */ |
| 63 | while ((timeout < 20000) && (REG_READ(gen_fifo_stat_reg) |
| 64 | & DSI_FIFO_GEN_HS_CTRL_FULL)) { |
| 65 | udelay(100); |
| 66 | timeout++; |
| 67 | } |
| 68 | if (timeout == 20000) |
| 69 | DRM_INFO("MIPI: HS CMD FIFO was never cleared!\n"); |
| 70 | } |
| 71 | |
| 72 | static void mdfld_wait_for_DPI_CTRL_FIFO(struct drm_device *dev, u32 pipe) |
| 73 | { |
| 74 | u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe); |
| 75 | int timeout = 0; |
| 76 | |
| 77 | udelay(500); |
| 78 | |
| 79 | /* This will time out after approximately 2+ seconds */ |
| 80 | while ((timeout < 20000) && ((REG_READ(gen_fifo_stat_reg) & |
| 81 | DPI_FIFO_EMPTY) != DPI_FIFO_EMPTY)) { |
| 82 | udelay(100); |
| 83 | timeout++; |
| 84 | } |
| 85 | |
| 86 | if (timeout == 20000) |
| 87 | DRM_ERROR("MIPI: DPI FIFO was never cleared\n"); |
| 88 | } |
| 89 | |
| 90 | static void mdfld_wait_for_SPL_PKG_SENT(struct drm_device *dev, u32 pipe) |
| 91 | { |
| 92 | u32 intr_stat_reg = MIPI_INTR_STAT_REG(pipe); |
| 93 | int timeout = 0; |
| 94 | |
| 95 | udelay(500); |
| 96 | |
| 97 | /* This will time out after approximately 2+ seconds */ |
| 98 | while ((timeout < 20000) && (!(REG_READ(intr_stat_reg) |
| 99 | & DSI_INTR_STATE_SPL_PKG_SENT))) { |
| 100 | udelay(100); |
| 101 | timeout++; |
| 102 | } |
| 103 | |
| 104 | if (timeout == 20000) |
| 105 | DRM_ERROR("MIPI: SPL_PKT_SENT_INTERRUPT was not sent successfully!\n"); |
| 106 | } |
| 107 | |
| 108 | /* For TC35876X */ |
| 109 | |
| 110 | static void dsi_set_device_ready_state(struct drm_device *dev, int state, |
| 111 | int pipe) |
| 112 | { |
| 113 | REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), !!state, 0, 0); |
| 114 | } |
| 115 | |
| 116 | static void dsi_set_pipe_plane_enable_state(struct drm_device *dev, |
| 117 | int state, int pipe) |
| 118 | { |
| 119 | struct drm_psb_private *dev_priv = dev->dev_private; |
| 120 | u32 pipeconf_reg = PIPEACONF; |
| 121 | u32 dspcntr_reg = DSPACNTR; |
| 122 | |
| 123 | u32 dspcntr = dev_priv->dspcntr[pipe]; |
| 124 | u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX; |
| 125 | |
| 126 | if (pipe) { |
| 127 | pipeconf_reg = PIPECCONF; |
| 128 | dspcntr_reg = DSPCCNTR; |
| 129 | } else |
| 130 | mipi &= (~0x03); |
| 131 | |
| 132 | if (state) { |
| 133 | /*Set up pipe */ |
| 134 | REG_WRITE(pipeconf_reg, BIT(31)); |
| 135 | |
| 136 | if (REG_BIT_WAIT(pipeconf_reg, 1, 30)) |
| 137 | dev_err(&dev->pdev->dev, "%s: Pipe enable timeout\n", |
| 138 | __func__); |
| 139 | |
| 140 | /*Set up display plane */ |
| 141 | REG_WRITE(dspcntr_reg, dspcntr); |
| 142 | } else { |
| 143 | u32 dspbase_reg = pipe ? MDFLD_DSPCBASE : MRST_DSPABASE; |
| 144 | |
| 145 | /* Put DSI lanes to ULPS to disable pipe */ |
| 146 | REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 2, 2, 1); |
| 147 | REG_READ(MIPI_DEVICE_READY_REG(pipe)); /* posted write? */ |
| 148 | |
| 149 | /* LP Hold */ |
| 150 | REG_FLD_MOD(MIPI_PORT_CONTROL(pipe), 0, 16, 16); |
| 151 | REG_READ(MIPI_PORT_CONTROL(pipe)); /* posted write? */ |
| 152 | |
| 153 | /* Disable display plane */ |
| 154 | REG_FLD_MOD(dspcntr_reg, 0, 31, 31); |
| 155 | |
| 156 | /* Flush the plane changes ??? posted write? */ |
| 157 | REG_WRITE(dspbase_reg, REG_READ(dspbase_reg)); |
| 158 | REG_READ(dspbase_reg); |
| 159 | |
| 160 | /* Disable PIPE */ |
| 161 | REG_FLD_MOD(pipeconf_reg, 0, 31, 31); |
| 162 | |
| 163 | if (REG_BIT_WAIT(pipeconf_reg, 0, 30)) |
| 164 | dev_err(&dev->pdev->dev, "%s: Pipe disable timeout\n", |
| 165 | __func__); |
| 166 | |
| 167 | if (REG_BIT_WAIT(MIPI_GEN_FIFO_STAT_REG(pipe), 1, 28)) |
| 168 | dev_err(&dev->pdev->dev, "%s: FIFO not empty\n", |
| 169 | __func__); |
| 170 | } |
| 171 | } |
| 172 | |
| 173 | static void mdfld_dsi_configure_down(struct mdfld_dsi_encoder *dsi_encoder, |
| 174 | int pipe) |
| 175 | { |
| 176 | struct mdfld_dsi_dpi_output *dpi_output = |
| 177 | MDFLD_DSI_DPI_OUTPUT(dsi_encoder); |
| 178 | struct mdfld_dsi_config *dsi_config = |
| 179 | mdfld_dsi_encoder_get_config(dsi_encoder); |
| 180 | struct drm_device *dev = dsi_config->dev; |
| 181 | struct drm_psb_private *dev_priv = dev->dev_private; |
| 182 | |
| 183 | if (!dev_priv->dpi_panel_on[pipe]) { |
| 184 | dev_err(dev->dev, "DPI panel is already off\n"); |
| 185 | return; |
| 186 | } |
| 187 | tc35876x_toshiba_bridge_panel_off(dev); |
| 188 | tc35876x_set_bridge_reset_state(dev, 1); |
| 189 | dsi_set_pipe_plane_enable_state(dev, 0, pipe); |
| 190 | mdfld_dsi_dpi_shut_down(dpi_output, pipe); |
| 191 | dsi_set_device_ready_state(dev, 0, pipe); |
| 192 | } |
| 193 | |
| 194 | static void mdfld_dsi_configure_up(struct mdfld_dsi_encoder *dsi_encoder, |
| 195 | int pipe) |
| 196 | { |
| 197 | struct mdfld_dsi_dpi_output *dpi_output = |
| 198 | MDFLD_DSI_DPI_OUTPUT(dsi_encoder); |
| 199 | struct mdfld_dsi_config *dsi_config = |
| 200 | mdfld_dsi_encoder_get_config(dsi_encoder); |
| 201 | struct drm_device *dev = dsi_config->dev; |
| 202 | struct drm_psb_private *dev_priv = dev->dev_private; |
| 203 | |
| 204 | if (dev_priv->dpi_panel_on[pipe]) { |
| 205 | dev_err(dev->dev, "DPI panel is already on\n"); |
| 206 | return; |
| 207 | } |
| 208 | |
| 209 | /* For resume path sequence */ |
| 210 | mdfld_dsi_dpi_shut_down(dpi_output, pipe); |
| 211 | dsi_set_device_ready_state(dev, 0, pipe); |
| 212 | |
| 213 | dsi_set_device_ready_state(dev, 1, pipe); |
| 214 | tc35876x_set_bridge_reset_state(dev, 0); |
| 215 | tc35876x_configure_lvds_bridge(dev); |
| 216 | mdfld_dsi_dpi_turn_on(dpi_output, pipe); /* Send turn on command */ |
| 217 | dsi_set_pipe_plane_enable_state(dev, 1, pipe); |
| 218 | } |
| 219 | /* End for TC35876X */ |
| 220 | |
| 221 | /* ************************************************************************* *\ |
| 222 | * FUNCTION: mdfld_dsi_tpo_ic_init |
| 223 | * |
| 224 | * DESCRIPTION: This function is called only by mrst_dsi_mode_set and |
| 225 | * restore_display_registers. since this function does not |
| 226 | * acquire the mutex, it is important that the calling function |
| 227 | * does! |
| 228 | \* ************************************************************************* */ |
| 229 | static void mdfld_dsi_tpo_ic_init(struct mdfld_dsi_config *dsi_config, u32 pipe) |
| 230 | { |
| 231 | struct drm_device *dev = dsi_config->dev; |
| 232 | u32 dcsChannelNumber = dsi_config->channel_num; |
| 233 | u32 gen_data_reg = MIPI_HS_GEN_DATA_REG(pipe); |
| 234 | u32 gen_ctrl_reg = MIPI_HS_GEN_CTRL_REG(pipe); |
| 235 | u32 gen_ctrl_val = GEN_LONG_WRITE; |
| 236 | |
| 237 | DRM_INFO("Enter mrst init TPO MIPI display.\n"); |
| 238 | |
| 239 | gen_ctrl_val |= dcsChannelNumber << DCS_CHANNEL_NUMBER_POS; |
| 240 | |
| 241 | /* Flip page order */ |
| 242 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 243 | REG_WRITE(gen_data_reg, 0x00008036); |
| 244 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 245 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS)); |
| 246 | |
| 247 | /* 0xF0 */ |
| 248 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 249 | REG_WRITE(gen_data_reg, 0x005a5af0); |
| 250 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 251 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS)); |
| 252 | |
| 253 | /* Write protection key */ |
| 254 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 255 | REG_WRITE(gen_data_reg, 0x005a5af1); |
| 256 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 257 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS)); |
| 258 | |
| 259 | /* 0xFC */ |
| 260 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 261 | REG_WRITE(gen_data_reg, 0x005a5afc); |
| 262 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 263 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS)); |
| 264 | |
| 265 | /* 0xB7 */ |
| 266 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 267 | REG_WRITE(gen_data_reg, 0x770000b7); |
| 268 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 269 | REG_WRITE(gen_data_reg, 0x00000044); |
| 270 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 271 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x05 << WORD_COUNTS_POS)); |
| 272 | |
| 273 | /* 0xB6 */ |
| 274 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 275 | REG_WRITE(gen_data_reg, 0x000a0ab6); |
| 276 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 277 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS)); |
| 278 | |
| 279 | /* 0xF2 */ |
| 280 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 281 | REG_WRITE(gen_data_reg, 0x081010f2); |
| 282 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 283 | REG_WRITE(gen_data_reg, 0x4a070708); |
| 284 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 285 | REG_WRITE(gen_data_reg, 0x000000c5); |
| 286 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 287 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS)); |
| 288 | |
| 289 | /* 0xF8 */ |
| 290 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 291 | REG_WRITE(gen_data_reg, 0x024003f8); |
| 292 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 293 | REG_WRITE(gen_data_reg, 0x01030a04); |
| 294 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 295 | REG_WRITE(gen_data_reg, 0x0e020220); |
| 296 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 297 | REG_WRITE(gen_data_reg, 0x00000004); |
| 298 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 299 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x0d << WORD_COUNTS_POS)); |
| 300 | |
| 301 | /* 0xE2 */ |
| 302 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 303 | REG_WRITE(gen_data_reg, 0x398fc3e2); |
| 304 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 305 | REG_WRITE(gen_data_reg, 0x0000916f); |
| 306 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 307 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x06 << WORD_COUNTS_POS)); |
| 308 | |
| 309 | /* 0xB0 */ |
| 310 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 311 | REG_WRITE(gen_data_reg, 0x000000b0); |
| 312 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 313 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS)); |
| 314 | |
| 315 | /* 0xF4 */ |
| 316 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 317 | REG_WRITE(gen_data_reg, 0x240242f4); |
| 318 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 319 | REG_WRITE(gen_data_reg, 0x78ee2002); |
| 320 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 321 | REG_WRITE(gen_data_reg, 0x2a071050); |
| 322 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 323 | REG_WRITE(gen_data_reg, 0x507fee10); |
| 324 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 325 | REG_WRITE(gen_data_reg, 0x10300710); |
| 326 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 327 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x14 << WORD_COUNTS_POS)); |
| 328 | |
| 329 | /* 0xBA */ |
| 330 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 331 | REG_WRITE(gen_data_reg, 0x19fe07ba); |
| 332 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 333 | REG_WRITE(gen_data_reg, 0x101c0a31); |
| 334 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 335 | REG_WRITE(gen_data_reg, 0x00000010); |
| 336 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 337 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS)); |
| 338 | |
| 339 | /* 0xBB */ |
| 340 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 341 | REG_WRITE(gen_data_reg, 0x28ff07bb); |
| 342 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 343 | REG_WRITE(gen_data_reg, 0x24280a31); |
| 344 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 345 | REG_WRITE(gen_data_reg, 0x00000034); |
| 346 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 347 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS)); |
| 348 | |
| 349 | /* 0xFB */ |
| 350 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 351 | REG_WRITE(gen_data_reg, 0x535d05fb); |
| 352 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 353 | REG_WRITE(gen_data_reg, 0x1b1a2130); |
| 354 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 355 | REG_WRITE(gen_data_reg, 0x221e180e); |
| 356 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 357 | REG_WRITE(gen_data_reg, 0x131d2120); |
| 358 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 359 | REG_WRITE(gen_data_reg, 0x535d0508); |
| 360 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 361 | REG_WRITE(gen_data_reg, 0x1c1a2131); |
| 362 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 363 | REG_WRITE(gen_data_reg, 0x231f160d); |
| 364 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 365 | REG_WRITE(gen_data_reg, 0x111b2220); |
| 366 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 367 | REG_WRITE(gen_data_reg, 0x535c2008); |
| 368 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 369 | REG_WRITE(gen_data_reg, 0x1f1d2433); |
| 370 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 371 | REG_WRITE(gen_data_reg, 0x2c251a10); |
| 372 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 373 | REG_WRITE(gen_data_reg, 0x2c34372d); |
| 374 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 375 | REG_WRITE(gen_data_reg, 0x00000023); |
| 376 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 377 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS)); |
| 378 | |
| 379 | /* 0xFA */ |
| 380 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 381 | REG_WRITE(gen_data_reg, 0x525c0bfa); |
| 382 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 383 | REG_WRITE(gen_data_reg, 0x1c1c232f); |
| 384 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 385 | REG_WRITE(gen_data_reg, 0x2623190e); |
| 386 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 387 | REG_WRITE(gen_data_reg, 0x18212625); |
| 388 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 389 | REG_WRITE(gen_data_reg, 0x545d0d0e); |
| 390 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 391 | REG_WRITE(gen_data_reg, 0x1e1d2333); |
| 392 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 393 | REG_WRITE(gen_data_reg, 0x26231a10); |
| 394 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 395 | REG_WRITE(gen_data_reg, 0x1a222725); |
| 396 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 397 | REG_WRITE(gen_data_reg, 0x545d280f); |
| 398 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 399 | REG_WRITE(gen_data_reg, 0x21202635); |
| 400 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 401 | REG_WRITE(gen_data_reg, 0x31292013); |
| 402 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 403 | REG_WRITE(gen_data_reg, 0x31393d33); |
| 404 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 405 | REG_WRITE(gen_data_reg, 0x00000029); |
| 406 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 407 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS)); |
| 408 | |
| 409 | /* Set DM */ |
| 410 | mdfld_wait_for_HS_DATA_FIFO(dev, pipe); |
| 411 | REG_WRITE(gen_data_reg, 0x000100f7); |
| 412 | mdfld_wait_for_HS_CTRL_FIFO(dev, pipe); |
| 413 | REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS)); |
| 414 | } |
| 415 | |
| 416 | static u16 mdfld_dsi_dpi_to_byte_clock_count(int pixel_clock_count, |
| 417 | int num_lane, int bpp) |
| 418 | { |
| 419 | return (u16)((pixel_clock_count * bpp) / (num_lane * 8)); |
| 420 | } |
| 421 | |
| 422 | /* |
| 423 | * Calculate the dpi time basing on a given drm mode @mode |
| 424 | * return 0 on success. |
| 425 | * FIXME: I was using proposed mode value for calculation, may need to |
| 426 | * use crtc mode values later |
| 427 | */ |
| 428 | int mdfld_dsi_dpi_timing_calculation(struct drm_display_mode *mode, |
| 429 | struct mdfld_dsi_dpi_timing *dpi_timing, |
| 430 | int num_lane, int bpp) |
| 431 | { |
| 432 | int pclk_hsync, pclk_hfp, pclk_hbp, pclk_hactive; |
Kirill A. Shutemov | e4b9ff7 | 2012-03-08 16:11:26 +0000 | [diff] [blame] | 433 | int pclk_vsync, pclk_vfp, pclk_vbp; |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 434 | |
| 435 | pclk_hactive = mode->hdisplay; |
| 436 | pclk_hfp = mode->hsync_start - mode->hdisplay; |
| 437 | pclk_hsync = mode->hsync_end - mode->hsync_start; |
| 438 | pclk_hbp = mode->htotal - mode->hsync_end; |
| 439 | |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 440 | pclk_vfp = mode->vsync_start - mode->vdisplay; |
| 441 | pclk_vsync = mode->vsync_end - mode->vsync_start; |
| 442 | pclk_vbp = mode->vtotal - mode->vsync_end; |
| 443 | |
| 444 | /* |
| 445 | * byte clock counts were calculated by following formula |
| 446 | * bclock_count = pclk_count * bpp / num_lane / 8 |
| 447 | */ |
| 448 | dpi_timing->hsync_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 449 | pclk_hsync, num_lane, bpp); |
| 450 | dpi_timing->hbp_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 451 | pclk_hbp, num_lane, bpp); |
| 452 | dpi_timing->hfp_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 453 | pclk_hfp, num_lane, bpp); |
| 454 | dpi_timing->hactive_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 455 | pclk_hactive, num_lane, bpp); |
| 456 | dpi_timing->vsync_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 457 | pclk_vsync, num_lane, bpp); |
| 458 | dpi_timing->vbp_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 459 | pclk_vbp, num_lane, bpp); |
| 460 | dpi_timing->vfp_count = mdfld_dsi_dpi_to_byte_clock_count( |
| 461 | pclk_vfp, num_lane, bpp); |
| 462 | |
| 463 | return 0; |
| 464 | } |
| 465 | |
| 466 | void mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config *dsi_config, |
| 467 | int pipe) |
| 468 | { |
| 469 | struct drm_device *dev = dsi_config->dev; |
| 470 | int lane_count = dsi_config->lane_count; |
| 471 | struct mdfld_dsi_dpi_timing dpi_timing; |
| 472 | struct drm_display_mode *mode = dsi_config->mode; |
| 473 | u32 val; |
| 474 | |
| 475 | /*un-ready device*/ |
| 476 | REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 0, 0, 0); |
| 477 | |
| 478 | /*init dsi adapter before kicking off*/ |
| 479 | REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018); |
| 480 | |
| 481 | /*enable all interrupts*/ |
| 482 | REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff); |
| 483 | |
| 484 | /*set up func_prg*/ |
| 485 | val = lane_count; |
| 486 | val |= dsi_config->channel_num << DSI_DPI_VIRT_CHANNEL_OFFSET; |
| 487 | |
| 488 | switch (dsi_config->bpp) { |
| 489 | case 16: |
| 490 | val |= DSI_DPI_COLOR_FORMAT_RGB565; |
| 491 | break; |
| 492 | case 18: |
| 493 | val |= DSI_DPI_COLOR_FORMAT_RGB666; |
| 494 | break; |
| 495 | case 24: |
| 496 | val |= DSI_DPI_COLOR_FORMAT_RGB888; |
| 497 | break; |
| 498 | default: |
| 499 | DRM_ERROR("unsupported color format, bpp = %d\n", |
| 500 | dsi_config->bpp); |
| 501 | } |
| 502 | REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), val); |
| 503 | |
| 504 | REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe), |
| 505 | (mode->vtotal * mode->htotal * dsi_config->bpp / |
| 506 | (8 * lane_count)) & DSI_HS_TX_TIMEOUT_MASK); |
| 507 | REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe), |
| 508 | 0xffff & DSI_LP_RX_TIMEOUT_MASK); |
| 509 | |
| 510 | /*max value: 20 clock cycles of txclkesc*/ |
| 511 | REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe), |
| 512 | 0x14 & DSI_TURN_AROUND_TIMEOUT_MASK); |
| 513 | |
| 514 | /*min 21 txclkesc, max: ffffh*/ |
| 515 | REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe), |
| 516 | 0xffff & DSI_RESET_TIMER_MASK); |
| 517 | |
| 518 | REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe), |
| 519 | mode->vdisplay << 16 | mode->hdisplay); |
| 520 | |
| 521 | /*set DPI timing registers*/ |
| 522 | mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing, |
| 523 | dsi_config->lane_count, dsi_config->bpp); |
| 524 | |
| 525 | REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe), |
| 526 | dpi_timing.hsync_count & DSI_DPI_TIMING_MASK); |
| 527 | REG_WRITE(MIPI_HBP_COUNT_REG(pipe), |
| 528 | dpi_timing.hbp_count & DSI_DPI_TIMING_MASK); |
| 529 | REG_WRITE(MIPI_HFP_COUNT_REG(pipe), |
| 530 | dpi_timing.hfp_count & DSI_DPI_TIMING_MASK); |
| 531 | REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe), |
| 532 | dpi_timing.hactive_count & DSI_DPI_TIMING_MASK); |
| 533 | REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe), |
| 534 | dpi_timing.vsync_count & DSI_DPI_TIMING_MASK); |
| 535 | REG_WRITE(MIPI_VBP_COUNT_REG(pipe), |
| 536 | dpi_timing.vbp_count & DSI_DPI_TIMING_MASK); |
| 537 | REG_WRITE(MIPI_VFP_COUNT_REG(pipe), |
| 538 | dpi_timing.vfp_count & DSI_DPI_TIMING_MASK); |
| 539 | |
| 540 | REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x46); |
| 541 | |
| 542 | /*min: 7d0 max: 4e20*/ |
| 543 | REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0x000007d0); |
| 544 | |
| 545 | /*set up video mode*/ |
| 546 | val = dsi_config->video_mode | DSI_DPI_COMPLETE_LAST_LINE; |
| 547 | REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), val); |
| 548 | |
| 549 | REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000); |
| 550 | |
| 551 | REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004); |
| 552 | |
| 553 | /*TODO: figure out how to setup these registers*/ |
| 554 | if (mdfld_get_panel_type(dev, pipe) == TC35876X) |
| 555 | REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008); |
| 556 | else |
| 557 | REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150c3408); |
| 558 | |
| 559 | REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14); |
| 560 | |
| 561 | if (mdfld_get_panel_type(dev, pipe) == TC35876X) |
| 562 | tc35876x_set_bridge_reset_state(dev, 0); /*Pull High Reset */ |
| 563 | |
| 564 | /*set device ready*/ |
| 565 | REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 1, 0, 0); |
| 566 | } |
| 567 | |
| 568 | void mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output *output, int pipe) |
| 569 | { |
| 570 | struct drm_device *dev = output->dev; |
| 571 | |
| 572 | /* clear special packet sent bit */ |
| 573 | if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT) |
| 574 | REG_WRITE(MIPI_INTR_STAT_REG(pipe), |
| 575 | DSI_INTR_STATE_SPL_PKG_SENT); |
| 576 | |
| 577 | /*send turn on package*/ |
| 578 | REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_TURN_ON); |
| 579 | |
| 580 | /*wait for SPL_PKG_SENT interrupt*/ |
| 581 | mdfld_wait_for_SPL_PKG_SENT(dev, pipe); |
| 582 | |
| 583 | if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT) |
| 584 | REG_WRITE(MIPI_INTR_STAT_REG(pipe), |
| 585 | DSI_INTR_STATE_SPL_PKG_SENT); |
| 586 | |
| 587 | output->panel_on = 1; |
| 588 | |
| 589 | /* FIXME the following is disabled to WA the X slow start issue |
| 590 | for TMD panel |
| 591 | if (pipe == 2) |
| 592 | dev_priv->dpi_panel_on2 = true; |
| 593 | else if (pipe == 0) |
| 594 | dev_priv->dpi_panel_on = true; */ |
| 595 | } |
| 596 | |
| 597 | static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output, |
| 598 | int pipe) |
| 599 | { |
| 600 | struct drm_device *dev = output->dev; |
| 601 | |
| 602 | /*if output is on, or mode setting didn't happen, ignore this*/ |
| 603 | if ((!output->panel_on) || output->first_boot) { |
| 604 | output->first_boot = 0; |
| 605 | return; |
| 606 | } |
| 607 | |
| 608 | /* Wait for dpi fifo to empty */ |
| 609 | mdfld_wait_for_DPI_CTRL_FIFO(dev, pipe); |
| 610 | |
| 611 | /* Clear the special packet interrupt bit if set */ |
| 612 | if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT) |
| 613 | REG_WRITE(MIPI_INTR_STAT_REG(pipe), |
| 614 | DSI_INTR_STATE_SPL_PKG_SENT); |
| 615 | |
| 616 | if (REG_READ(MIPI_DPI_CONTROL_REG(pipe)) == DSI_DPI_CTRL_HS_SHUTDOWN) |
| 617 | goto shutdown_out; |
| 618 | |
| 619 | REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_SHUTDOWN); |
| 620 | |
| 621 | shutdown_out: |
| 622 | output->panel_on = 0; |
| 623 | output->first_boot = 0; |
| 624 | |
| 625 | /* FIXME the following is disabled to WA the X slow start issue |
| 626 | for TMD panel |
| 627 | if (pipe == 2) |
| 628 | dev_priv->dpi_panel_on2 = false; |
| 629 | else if (pipe == 0) |
| 630 | dev_priv->dpi_panel_on = false; */ |
| 631 | } |
| 632 | |
| 633 | static void mdfld_dsi_dpi_set_power(struct drm_encoder *encoder, bool on) |
| 634 | { |
| 635 | struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder); |
| 636 | struct mdfld_dsi_dpi_output *dpi_output = |
| 637 | MDFLD_DSI_DPI_OUTPUT(dsi_encoder); |
| 638 | struct mdfld_dsi_config *dsi_config = |
| 639 | mdfld_dsi_encoder_get_config(dsi_encoder); |
| 640 | int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder); |
| 641 | struct drm_device *dev = dsi_config->dev; |
| 642 | struct drm_psb_private *dev_priv = dev->dev_private; |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 643 | |
| 644 | /*start up display island if it was shutdown*/ |
| 645 | if (!gma_power_begin(dev, true)) |
| 646 | return; |
| 647 | |
| 648 | if (on) { |
| 649 | if (mdfld_get_panel_type(dev, pipe) == TMD_VID) |
| 650 | mdfld_dsi_dpi_turn_on(dpi_output, pipe); |
| 651 | else if (mdfld_get_panel_type(dev, pipe) == TC35876X) |
| 652 | mdfld_dsi_configure_up(dsi_encoder, pipe); |
| 653 | else { |
| 654 | /*enable mipi port*/ |
| 655 | REG_WRITE(MIPI_PORT_CONTROL(pipe), |
| 656 | REG_READ(MIPI_PORT_CONTROL(pipe)) | BIT(31)); |
| 657 | REG_READ(MIPI_PORT_CONTROL(pipe)); |
| 658 | |
| 659 | mdfld_dsi_dpi_turn_on(dpi_output, pipe); |
| 660 | mdfld_dsi_tpo_ic_init(dsi_config, pipe); |
| 661 | } |
| 662 | dev_priv->dpi_panel_on[pipe] = true; |
| 663 | } else { |
| 664 | if (mdfld_get_panel_type(dev, pipe) == TMD_VID) |
| 665 | mdfld_dsi_dpi_shut_down(dpi_output, pipe); |
| 666 | else if (mdfld_get_panel_type(dev, pipe) == TC35876X) |
| 667 | mdfld_dsi_configure_down(dsi_encoder, pipe); |
| 668 | else { |
| 669 | mdfld_dsi_dpi_shut_down(dpi_output, pipe); |
| 670 | |
| 671 | /*disable mipi port*/ |
| 672 | REG_WRITE(MIPI_PORT_CONTROL(pipe), |
| 673 | REG_READ(MIPI_PORT_CONTROL(pipe)) & ~BIT(31)); |
| 674 | REG_READ(MIPI_PORT_CONTROL(pipe)); |
| 675 | } |
| 676 | dev_priv->dpi_panel_on[pipe] = false; |
| 677 | } |
| 678 | gma_power_end(dev); |
| 679 | } |
| 680 | |
| 681 | void mdfld_dsi_dpi_dpms(struct drm_encoder *encoder, int mode) |
| 682 | { |
| 683 | mdfld_dsi_dpi_set_power(encoder, mode == DRM_MODE_DPMS_ON); |
| 684 | } |
| 685 | |
| 686 | bool mdfld_dsi_dpi_mode_fixup(struct drm_encoder *encoder, |
Laurent Pinchart | e811f5a | 2012-07-17 17:56:50 +0200 | [diff] [blame] | 687 | const struct drm_display_mode *mode, |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 688 | struct drm_display_mode *adjusted_mode) |
| 689 | { |
| 690 | struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder); |
| 691 | struct mdfld_dsi_config *dsi_config = |
| 692 | mdfld_dsi_encoder_get_config(dsi_encoder); |
| 693 | struct drm_display_mode *fixed_mode = dsi_config->fixed_mode; |
| 694 | |
| 695 | if (fixed_mode) { |
| 696 | adjusted_mode->hdisplay = fixed_mode->hdisplay; |
| 697 | adjusted_mode->hsync_start = fixed_mode->hsync_start; |
| 698 | adjusted_mode->hsync_end = fixed_mode->hsync_end; |
| 699 | adjusted_mode->htotal = fixed_mode->htotal; |
| 700 | adjusted_mode->vdisplay = fixed_mode->vdisplay; |
| 701 | adjusted_mode->vsync_start = fixed_mode->vsync_start; |
| 702 | adjusted_mode->vsync_end = fixed_mode->vsync_end; |
| 703 | adjusted_mode->vtotal = fixed_mode->vtotal; |
| 704 | adjusted_mode->clock = fixed_mode->clock; |
| 705 | drm_mode_set_crtcinfo(adjusted_mode, CRTC_INTERLACE_HALVE_V); |
| 706 | } |
| 707 | return true; |
| 708 | } |
| 709 | |
| 710 | void mdfld_dsi_dpi_prepare(struct drm_encoder *encoder) |
| 711 | { |
| 712 | mdfld_dsi_dpi_set_power(encoder, false); |
| 713 | } |
| 714 | |
| 715 | void mdfld_dsi_dpi_commit(struct drm_encoder *encoder) |
| 716 | { |
| 717 | mdfld_dsi_dpi_set_power(encoder, true); |
| 718 | } |
| 719 | |
| 720 | /* For TC35876X */ |
| 721 | /* This functionality was implemented in FW in iCDK */ |
| 722 | /* But removed in DV0 and later. So need to add here. */ |
| 723 | static void mipi_set_properties(struct mdfld_dsi_config *dsi_config, int pipe) |
| 724 | { |
| 725 | struct drm_device *dev = dsi_config->dev; |
| 726 | |
| 727 | REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018); |
| 728 | REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff); |
| 729 | REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe), 0xffffff); |
| 730 | REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe), 0xffffff); |
| 731 | REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe), 0x14); |
| 732 | REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe), 0xff); |
| 733 | REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x25); |
| 734 | REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0xf0); |
| 735 | REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000); |
| 736 | REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004); |
| 737 | REG_WRITE(MIPI_DBI_BW_CTRL_REG(pipe), 0x00000820); |
| 738 | REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14); |
| 739 | } |
| 740 | |
| 741 | static void mdfld_mipi_set_video_timing(struct mdfld_dsi_config *dsi_config, |
| 742 | int pipe) |
| 743 | { |
| 744 | struct drm_device *dev = dsi_config->dev; |
| 745 | struct mdfld_dsi_dpi_timing dpi_timing; |
| 746 | struct drm_display_mode *mode = dsi_config->mode; |
| 747 | |
| 748 | mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing, |
| 749 | dsi_config->lane_count, |
| 750 | dsi_config->bpp); |
| 751 | |
| 752 | REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe), |
| 753 | mode->vdisplay << 16 | mode->hdisplay); |
| 754 | REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe), |
| 755 | dpi_timing.hsync_count & DSI_DPI_TIMING_MASK); |
| 756 | REG_WRITE(MIPI_HBP_COUNT_REG(pipe), |
| 757 | dpi_timing.hbp_count & DSI_DPI_TIMING_MASK); |
| 758 | REG_WRITE(MIPI_HFP_COUNT_REG(pipe), |
| 759 | dpi_timing.hfp_count & DSI_DPI_TIMING_MASK); |
| 760 | REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe), |
| 761 | dpi_timing.hactive_count & DSI_DPI_TIMING_MASK); |
| 762 | REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe), |
| 763 | dpi_timing.vsync_count & DSI_DPI_TIMING_MASK); |
| 764 | REG_WRITE(MIPI_VBP_COUNT_REG(pipe), |
| 765 | dpi_timing.vbp_count & DSI_DPI_TIMING_MASK); |
| 766 | REG_WRITE(MIPI_VFP_COUNT_REG(pipe), |
| 767 | dpi_timing.vfp_count & DSI_DPI_TIMING_MASK); |
| 768 | } |
| 769 | |
| 770 | static void mdfld_mipi_config(struct mdfld_dsi_config *dsi_config, int pipe) |
| 771 | { |
| 772 | struct drm_device *dev = dsi_config->dev; |
| 773 | int lane_count = dsi_config->lane_count; |
| 774 | |
| 775 | if (pipe) { |
| 776 | REG_WRITE(MIPI_PORT_CONTROL(0), 0x00000002); |
| 777 | REG_WRITE(MIPI_PORT_CONTROL(2), 0x80000000); |
| 778 | } else { |
| 779 | REG_WRITE(MIPI_PORT_CONTROL(0), 0x80010000); |
| 780 | REG_WRITE(MIPI_PORT_CONTROL(2), 0x00); |
| 781 | } |
| 782 | |
| 783 | REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150A600F); |
| 784 | REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), 0x0000000F); |
| 785 | |
| 786 | /* lane_count = 3 */ |
| 787 | REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), 0x00000200 | lane_count); |
| 788 | |
| 789 | mdfld_mipi_set_video_timing(dsi_config, pipe); |
| 790 | } |
| 791 | |
| 792 | static void mdfld_set_pipe_timing(struct mdfld_dsi_config *dsi_config, int pipe) |
| 793 | { |
| 794 | struct drm_device *dev = dsi_config->dev; |
| 795 | struct drm_display_mode *mode = dsi_config->mode; |
| 796 | |
| 797 | REG_WRITE(HTOTAL_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1)); |
| 798 | REG_WRITE(HBLANK_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1)); |
| 799 | REG_WRITE(HSYNC_A, |
| 800 | ((mode->hsync_end - 1) << 16) | (mode->hsync_start - 1)); |
| 801 | |
| 802 | REG_WRITE(VTOTAL_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1)); |
| 803 | REG_WRITE(VBLANK_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1)); |
| 804 | REG_WRITE(VSYNC_A, |
| 805 | ((mode->vsync_end - 1) << 16) | (mode->vsync_start - 1)); |
| 806 | |
| 807 | REG_WRITE(PIPEASRC, |
| 808 | ((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1)); |
| 809 | } |
| 810 | /* End for TC35876X */ |
| 811 | |
| 812 | void mdfld_dsi_dpi_mode_set(struct drm_encoder *encoder, |
| 813 | struct drm_display_mode *mode, |
| 814 | struct drm_display_mode *adjusted_mode) |
| 815 | { |
| 816 | struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder); |
| 817 | struct mdfld_dsi_dpi_output *dpi_output = |
| 818 | MDFLD_DSI_DPI_OUTPUT(dsi_encoder); |
| 819 | struct mdfld_dsi_config *dsi_config = |
| 820 | mdfld_dsi_encoder_get_config(dsi_encoder); |
| 821 | struct drm_device *dev = dsi_config->dev; |
| 822 | struct drm_psb_private *dev_priv = dev->dev_private; |
| 823 | int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder); |
| 824 | |
| 825 | u32 pipeconf_reg = PIPEACONF; |
| 826 | u32 dspcntr_reg = DSPACNTR; |
| 827 | |
| 828 | u32 pipeconf = dev_priv->pipeconf[pipe]; |
| 829 | u32 dspcntr = dev_priv->dspcntr[pipe]; |
| 830 | u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX; |
| 831 | |
| 832 | if (pipe) { |
| 833 | pipeconf_reg = PIPECCONF; |
| 834 | dspcntr_reg = DSPCCNTR; |
| 835 | } else { |
| 836 | if (mdfld_get_panel_type(dev, pipe) == TC35876X) |
| 837 | mipi &= (~0x03); /* Use all four lanes */ |
| 838 | else |
| 839 | mipi |= 2; |
| 840 | } |
| 841 | |
| 842 | /*start up display island if it was shutdown*/ |
| 843 | if (!gma_power_begin(dev, true)) |
| 844 | return; |
| 845 | |
| 846 | if (mdfld_get_panel_type(dev, pipe) == TC35876X) { |
| 847 | /* |
| 848 | * The following logic is required to reset the bridge and |
| 849 | * configure. This also starts the DSI clock at 200MHz. |
| 850 | */ |
| 851 | tc35876x_set_bridge_reset_state(dev, 0); /*Pull High Reset */ |
| 852 | tc35876x_toshiba_bridge_panel_on(dev); |
| 853 | udelay(100); |
| 854 | /* Now start the DSI clock */ |
| 855 | REG_WRITE(MRST_DPLL_A, 0x00); |
| 856 | REG_WRITE(MRST_FPA0, 0xC1); |
| 857 | REG_WRITE(MRST_DPLL_A, 0x00800000); |
| 858 | udelay(500); |
| 859 | REG_WRITE(MRST_DPLL_A, 0x80800000); |
| 860 | |
| 861 | if (REG_BIT_WAIT(pipeconf_reg, 1, 29)) |
| 862 | dev_err(&dev->pdev->dev, "%s: DSI PLL lock timeout\n", |
| 863 | __func__); |
| 864 | |
| 865 | REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008); |
| 866 | |
| 867 | mipi_set_properties(dsi_config, pipe); |
| 868 | mdfld_mipi_config(dsi_config, pipe); |
| 869 | mdfld_set_pipe_timing(dsi_config, pipe); |
| 870 | |
| 871 | REG_WRITE(DSPABASE, 0x00); |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 872 | REG_WRITE(DSPASIZE, |
| 873 | ((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1)); |
| 874 | |
| 875 | REG_WRITE(DSPACNTR, 0x98000000); |
| 876 | REG_WRITE(DSPASURF, 0x00); |
| 877 | |
| 878 | REG_WRITE(VGACNTRL, 0x80000000); |
| 879 | REG_WRITE(DEVICE_READY_REG, 0x00000001); |
| 880 | |
| 881 | REG_WRITE(MIPI_PORT_CONTROL(pipe), 0x80810000); |
| 882 | } else { |
| 883 | /*set up mipi port FIXME: do at init time */ |
| 884 | REG_WRITE(MIPI_PORT_CONTROL(pipe), mipi); |
| 885 | } |
| 886 | REG_READ(MIPI_PORT_CONTROL(pipe)); |
| 887 | |
| 888 | if (mdfld_get_panel_type(dev, pipe) == TMD_VID) { |
| 889 | /* NOP */ |
| 890 | } else if (mdfld_get_panel_type(dev, pipe) == TC35876X) { |
| 891 | /* set up DSI controller DPI interface */ |
| 892 | mdfld_dsi_dpi_controller_init(dsi_config, pipe); |
| 893 | |
| 894 | /* Configure MIPI Bridge and Panel */ |
| 895 | tc35876x_configure_lvds_bridge(dev); |
| 896 | dev_priv->dpi_panel_on[pipe] = true; |
| 897 | } else { |
| 898 | /*turn on DPI interface*/ |
| 899 | mdfld_dsi_dpi_turn_on(dpi_output, pipe); |
| 900 | } |
| 901 | |
| 902 | /*set up pipe*/ |
| 903 | REG_WRITE(pipeconf_reg, pipeconf); |
| 904 | REG_READ(pipeconf_reg); |
| 905 | |
| 906 | /*set up display plane*/ |
| 907 | REG_WRITE(dspcntr_reg, dspcntr); |
| 908 | REG_READ(dspcntr_reg); |
| 909 | |
| 910 | msleep(20); /* FIXME: this should wait for vblank */ |
| 911 | |
| 912 | if (mdfld_get_panel_type(dev, pipe) == TMD_VID) { |
| 913 | /* NOP */ |
| 914 | } else if (mdfld_get_panel_type(dev, pipe) == TC35876X) { |
| 915 | mdfld_dsi_dpi_turn_on(dpi_output, pipe); |
| 916 | } else { |
| 917 | /* init driver ic */ |
| 918 | mdfld_dsi_tpo_ic_init(dsi_config, pipe); |
| 919 | /*init backlight*/ |
| 920 | mdfld_dsi_brightness_init(dsi_config, pipe); |
| 921 | } |
| 922 | |
| 923 | gma_power_end(dev); |
| 924 | } |
| 925 | |
| 926 | /* |
| 927 | * Init DSI DPI encoder. |
| 928 | * Allocate an mdfld_dsi_encoder and attach it to given @dsi_connector |
| 929 | * return pointer of newly allocated DPI encoder, NULL on error |
| 930 | */ |
| 931 | struct mdfld_dsi_encoder *mdfld_dsi_dpi_init(struct drm_device *dev, |
| 932 | struct mdfld_dsi_connector *dsi_connector, |
| 933 | const struct panel_funcs *p_funcs) |
| 934 | { |
| 935 | struct mdfld_dsi_dpi_output *dpi_output = NULL; |
| 936 | struct mdfld_dsi_config *dsi_config; |
| 937 | struct drm_connector *connector = NULL; |
| 938 | struct drm_encoder *encoder = NULL; |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 939 | int pipe; |
| 940 | u32 data; |
| 941 | int ret; |
| 942 | |
| 943 | pipe = dsi_connector->pipe; |
| 944 | |
| 945 | if (mdfld_get_panel_type(dev, pipe) != TC35876X) { |
| 946 | dsi_config = mdfld_dsi_get_config(dsi_connector); |
| 947 | |
| 948 | /* panel hard-reset */ |
| 949 | if (p_funcs->reset) { |
| 950 | ret = p_funcs->reset(pipe); |
| 951 | if (ret) { |
| 952 | DRM_ERROR("Panel %d hard-reset failed\n", pipe); |
| 953 | return NULL; |
| 954 | } |
| 955 | } |
| 956 | |
| 957 | /* panel drvIC init */ |
| 958 | if (p_funcs->drv_ic_init) |
| 959 | p_funcs->drv_ic_init(dsi_config, pipe); |
| 960 | |
| 961 | /* panel power mode detect */ |
| 962 | ret = mdfld_dsi_get_power_mode(dsi_config, &data, false); |
| 963 | if (ret) { |
| 964 | DRM_ERROR("Panel %d get power mode failed\n", pipe); |
| 965 | dsi_connector->status = connector_status_disconnected; |
| 966 | } else { |
| 967 | DRM_INFO("pipe %d power mode 0x%x\n", pipe, data); |
| 968 | dsi_connector->status = connector_status_connected; |
| 969 | } |
| 970 | } |
| 971 | |
| 972 | dpi_output = kzalloc(sizeof(struct mdfld_dsi_dpi_output), GFP_KERNEL); |
| 973 | if (!dpi_output) { |
| 974 | DRM_ERROR("No memory\n"); |
| 975 | return NULL; |
| 976 | } |
| 977 | |
| 978 | if (dsi_connector->pipe) |
| 979 | dpi_output->panel_on = 0; |
| 980 | else |
| 981 | dpi_output->panel_on = 0; |
| 982 | |
| 983 | dpi_output->dev = dev; |
| 984 | if (mdfld_get_panel_type(dev, pipe) != TC35876X) |
| 985 | dpi_output->p_funcs = p_funcs; |
| 986 | dpi_output->first_boot = 1; |
| 987 | |
| 988 | /*get fixed mode*/ |
| 989 | dsi_config = mdfld_dsi_get_config(dsi_connector); |
Kirill A. Shutemov | 026abc3 | 2012-03-08 16:02:20 +0000 | [diff] [blame] | 990 | |
| 991 | /*create drm encoder object*/ |
| 992 | connector = &dsi_connector->base.base; |
| 993 | encoder = &dpi_output->base.base.base; |
| 994 | drm_encoder_init(dev, |
| 995 | encoder, |
| 996 | p_funcs->encoder_funcs, |
| 997 | DRM_MODE_ENCODER_LVDS); |
| 998 | drm_encoder_helper_add(encoder, |
| 999 | p_funcs->encoder_helper_funcs); |
| 1000 | |
| 1001 | /*attach to given connector*/ |
| 1002 | drm_mode_connector_attach_encoder(connector, encoder); |
| 1003 | |
| 1004 | /*set possible crtcs and clones*/ |
| 1005 | if (dsi_connector->pipe) { |
| 1006 | encoder->possible_crtcs = (1 << 2); |
| 1007 | encoder->possible_clones = (1 << 1); |
| 1008 | } else { |
| 1009 | encoder->possible_crtcs = (1 << 0); |
| 1010 | encoder->possible_clones = (1 << 0); |
| 1011 | } |
| 1012 | |
| 1013 | dsi_connector->base.encoder = &dpi_output->base.base; |
| 1014 | |
| 1015 | return &dpi_output->base; |
| 1016 | } |