arch/arm/boot/dts/omap3-ldp.dts

/*
 * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 */
/dts-v1/;

#include "omap34xx.dtsi"
#include "omap-gpmc-smsc911x.dtsi"

/ {
	model = "TI OMAP3430 LDP (Zoom1 Labrador)";
	compatible = "ti,omap3-ldp", "ti,omap3";

	memory {
		device_type = "memory";
		reg = <0x80000000 0x8000000>; /* 128 MB */
	};

	cpus {
		cpu@0 {
			cpu0-supply = <&vcc>;
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_key_pins>;

		key_enter {
			label = "enter";
			gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* gpio101 */
			linux,code = <0x0107001c>; /* KEY_ENTER */
			gpio-key,wakeup;
		};

		key_f1 {
			label = "f1";
			gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* gpio102 */
			linux,code = <0x0303003b>; /* KEY_F1 */
			gpio-key,wakeup;
		};

		key_f2 {
			label = "f2";
			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; /* gpio103 */
			linux,code = <0x0403003c>; /* KEY_F2 */
			gpio-key,wakeup;
		};

		key_f3 {
			label = "f3";
			gpios = <&gpio4 8 GPIO_ACTIVE_LOW>; /* gpio104 */
			linux,code = <0x0503003d>; /* KEY_F3 */
			gpio-key,wakeup;
		};

		key_f4 {
			label = "f4";
			gpios = <&gpio4 9 GPIO_ACTIVE_LOW>; /* gpio105 */
			linux,code = <0x0704003e>; /* KEY_F4 */
			gpio-key,wakeup;
		};

		key_left {
			label = "left";
			gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* gpio106 */
			linux,code = <0x04070069>; /* KEY_LEFT */
			gpio-key,wakeup;
		};

		key_right {
			label = "right";
			gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* gpio107 */
			linux,code = <0x0507006a>; /* KEY_RIGHT */
			gpio-key,wakeup;
		};

		key_up {
			label = "up";
			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; /* gpio108 */
			linux,code = <0x06070067>; /* KEY_UP */
			gpio-key,wakeup;
		};

		key_down {
			label = "down";
			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; /* gpio109 */
			linux,code = <0x0707006c>; /* KEY_DOWN */
			gpio-key,wakeup;
		};
	};
};

&gpmc {
	ranges = <0 0 0x00000000 0x01000000>,
		 <1 0 0x08000000 0x01000000>;

	nand@0,0 {
		linux,mtd-name= "micron,nand";
		reg = <0 0 0>;
		nand-bus-width = <16>;
		ti,nand-ecc-opt = "bch8";

		gpmc,sync-clk-ps = <0>;
		gpmc,cs-on-ns = <0>;
		gpmc,cs-rd-off-ns = <44>;
		gpmc,cs-wr-off-ns = <44>;
		gpmc,adv-on-ns = <6>;
		gpmc,adv-rd-off-ns = <34>;
		gpmc,adv-wr-off-ns = <44>;
		gpmc,we-off-ns = <40>;
		gpmc,oe-off-ns = <54>;
		gpmc,access-ns = <64>;
		gpmc,rd-cycle-ns = <82>;
		gpmc,wr-cycle-ns = <82>;
		gpmc,wr-access-ns = <40>;
		gpmc,wr-data-mux-bus-ns = <0>;

		#address-cells = <1>;
		#size-cells = <1>;

		partition@0 {
			label = "X-Loader";
			reg = <0 0x80000>;
		};
		partition@80000 {
			label = "U-Boot";
			reg = <0x80000 0x140000>;
		};
		partition@1c0000 {
			label = "Environment";
			reg = <0x1c0000 0x40000>;
		};
		partition@200000 {
			label = "Kernel";
			reg = <0x200000 0x1e00000>;
		};
		partition@2000000 {
			label = "Filesystem";
			reg = <0x2000000 0xe000000>;
		};
	};

	ethernet@gpmc {
		interrupt-parent = <&gpio5>;
		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
		reg = <1 0 0xff>;
	};
};

&i2c1 {
	clock-frequency = <2600000>;

	twl: twl@48 {
		reg = <0x48>;
		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
		interrupt-parent = <&intc>;
	};
};

#include "twl4030.dtsi"
#include "twl4030_omap3.dtsi"
#include "omap3-panel-sharp-ls037v7dw01.dtsi"

&backlight0 {
	gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
};

&i2c2 {
	clock-frequency = <400000>;
};

&i2c3 {
	clock-frequency = <400000>;
};

/* tps61130rsa enabled by twl4030 regen */
&lcd_3v3 {
	regulator-always-on;
};

&lcd0 {
	enable-gpios = <&twl_gpio 15 GPIO_ACTIVE_HIGH>;	/* lcd INI */
	reset-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;	/* gpio55, lcd RESB */
	mode-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;	/* gpio56, lcd MO */
};

&mcspi1 {
	tsc2046@0 {
		interrupt-parent = <&gpio2>;
		interrupts = <22 0>;		/* gpio54 */
		pendown-gpio = <&gpio2 22 0>;
	};
};

&mmc1 {
	/* See 35xx errata 2.1.1.128 in SPRZ278F */
	compatible = "ti,omap3-pre-es3-hsmmc";
	vmmc-supply = <&vmmc1>;
	bus-width = <4>;
	pinctrl-names = "default";
	pinctrl-0 = <&mmc1_pins>;
};

&mmc2 {
	status="disabled";
};

&mmc3 {
	status="disabled";
};

&omap3_pmx_core {
	gpio_key_pins: pinmux_gpio_key_pins {
		pinctrl-single,pins = <
			0xea (PIN_INPUT | MUX_MODE4)	/* cam_d2.gpio_101 */
			0xec (PIN_INPUT | MUX_MODE4)	/* cam_d3.gpio_102 */
			0xee (PIN_INPUT | MUX_MODE4)	/* cam_d4.gpio_103 */
			0xf0 (PIN_INPUT | MUX_MODE4)	/* cam_d5.gpio_104 */
			0xf2 (PIN_INPUT | MUX_MODE4)	/* cam_d6.gpio_105 */
			0xf4 (PIN_INPUT | MUX_MODE4)	/* cam_d7.gpio_106 */
			0xf6 (PIN_INPUT | MUX_MODE4)	/* cam_d8.gpio_107 */
			0xf8 (PIN_INPUT | MUX_MODE4)	/* cam_d9.gpio_108 */
			0xfa (PIN_INPUT | MUX_MODE4)	/* cam_d10.gpio_109 */
		>;
	};

	musb_pins: pinmux_musb_pins {
		pinctrl-single,pins = <
			0x172 (PIN_INPUT | MUX_MODE0)	/* hsusb0_clk.hsusb0_clk */
			0x17a (PIN_INPUT | MUX_MODE0)	/* hsusb0_data0.hsusb0_data0 */
			0x17c (PIN_INPUT | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
			0x17e (PIN_INPUT | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
			0x180 (PIN_INPUT | MUX_MODE0)	/* hsusb0_data3.hsusb0_data3 */
			0x182 (PIN_INPUT | MUX_MODE0)	/* hsusb0_data4.hsusb0_data4 */
			0x184 (PIN_INPUT | MUX_MODE0)	/* hsusb0_data5.hsusb0_data5 */
			0x186 (PIN_INPUT | MUX_MODE0)	/* hsusb0_data6.hsusb0_data6 */
			0x188 (PIN_INPUT | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
			0x176 (PIN_INPUT | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
			0x178 (PIN_INPUT | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
			0x174 (PIN_OUTPUT | MUX_MODE0)	/* hsusb0_stp.hsusb0_stp */
		>;
	};

	mmc1_pins: pinmux_mmc1_pins {
		pinctrl-single,pins = <
			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_clk.mmc1_clk */
			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_cmd.mmc1_cmd */
			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat0.mmc1_dat0 */
			OMAP3_CORE1_IOPAD(0x214A, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat1.mmc1_dat1 */
			OMAP3_CORE1_IOPAD(0x214C, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat2.mmc1_dat2 */
			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc1_dat3.mmc1_dat3 */
		>;
	};
};

&uart3 {
	interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
};

&usb_otg_hs {
	pinctrl-names = "default";
	pinctrl-0 = <&musb_pins>;
	interface-type = <0>;
	usb-phy = <&usb2_phy>;
	mode = <3>;
	power = <50>;
};

&vaux1 {
	/* Needed for ads7846 */
        regulator-name = "vcc";
};