| Vivek Gautam | 0b56e9a | 2017-05-11 12:17:42 +0530 | [diff] [blame] | 1 | # |
| 2 | # Phy drivers for TI platforms |
| 3 | # |
| 4 | config PHY_DA8XX_USB |
| 5 | tristate "TI DA8xx USB PHY Driver" |
| 6 | depends on ARCH_DAVINCI_DA8XX |
| 7 | select GENERIC_PHY |
| 8 | select MFD_SYSCON |
| 9 | help |
| 10 | Enable this to support the USB PHY on DA8xx SoCs. |
| 11 | |
| 12 | This driver controls both the USB 1.1 PHY and the USB 2.0 PHY. |
| 13 | |
| 14 | config PHY_DM816X_USB |
| 15 | tristate "TI dm816x USB PHY driver" |
| 16 | depends on ARCH_OMAP2PLUS |
| 17 | depends on USB_SUPPORT |
| 18 | select GENERIC_PHY |
| 19 | select USB_PHY |
| 20 | help |
| 21 | Enable this for dm816x USB to work. |
| 22 | |
| 23 | config OMAP_CONTROL_PHY |
| 24 | tristate "OMAP CONTROL PHY Driver" |
| 25 | depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| 26 | help |
| 27 | Enable this to add support for the PHY part present in the control |
| 28 | module. This driver has API to power on the USB2 PHY and to write to |
| 29 | the mailbox. The mailbox is present only in omap4 and the register to |
| 30 | power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an |
| 31 | additional register to power on USB3 PHY/SATA PHY/PCIE PHY |
| 32 | (PIPE3 PHY). |
| 33 | |
| 34 | config OMAP_USB2 |
| 35 | tristate "OMAP USB2 PHY Driver" |
| 36 | depends on ARCH_OMAP2PLUS |
| 37 | depends on USB_SUPPORT |
| 38 | select GENERIC_PHY |
| 39 | select USB_PHY |
| 40 | select OMAP_CONTROL_PHY |
| 41 | depends on OMAP_OCP2SCP |
| 42 | help |
| 43 | Enable this to support the transceiver that is part of SOC. This |
| 44 | driver takes care of all the PHY functionality apart from comparator. |
| 45 | The USB OTG controller communicates with the comparator using this |
| 46 | driver. |
| 47 | |
| 48 | config TI_PIPE3 |
| 49 | tristate "TI PIPE3 PHY Driver" |
| 50 | depends on ARCH_OMAP2PLUS || COMPILE_TEST |
| 51 | select GENERIC_PHY |
| 52 | select OMAP_CONTROL_PHY |
| 53 | depends on OMAP_OCP2SCP |
| 54 | help |
| 55 | Enable this to support the PIPE3 PHY that is part of TI SOCs. This |
| 56 | driver takes care of all the PHY functionality apart from comparator. |
| 57 | This driver interacts with the "OMAP Control PHY Driver" to power |
| 58 | on/off the PHY. |
| 59 | |
| 60 | config PHY_TUSB1210 |
| 61 | tristate "TI TUSB1210 ULPI PHY module" |
| 62 | depends on USB_ULPI_BUS |
| 63 | select GENERIC_PHY |
| 64 | help |
| 65 | Support for TI TUSB1210 USB ULPI PHY. |
| 66 | |
| 67 | config TWL4030_USB |
| 68 | tristate "TWL4030 USB Transceiver Driver" |
| 69 | depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS |
| 70 | depends on USB_SUPPORT |
| 71 | depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y' |
| 72 | select GENERIC_PHY |
| 73 | select USB_PHY |
| 74 | help |
| 75 | Enable this to support the USB OTG transceiver on TWL4030 |
| 76 | family chips (including the TWL5030 and TPS659x0 devices). |
| 77 | This transceiver supports high and full speed devices plus, |
| 78 | in host mode, low speed. |