Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 1 | /* |
| 2 | * Toshiba PCI Secure Digital Host Controller Interface driver |
| 3 | * |
| 4 | * Copyright (C) 2014 Ondrej Zary |
| 5 | * Copyright (C) 2007 Richard Betts, All Rights Reserved. |
| 6 | * |
| 7 | * Based on asic3_mmc.c, copyright (c) 2005 SDG Systems, LLC and, |
| 8 | * sdhci.c, copyright (C) 2005-2006 Pierre Ossman |
| 9 | * |
| 10 | * This program is free software; you can redistribute it and/or modify |
| 11 | * it under the terms of the GNU General Public License as published by |
| 12 | * the Free Software Foundation; either version 2 of the License, or (at |
| 13 | * your option) any later version. |
| 14 | */ |
| 15 | |
| 16 | #include <linux/delay.h> |
| 17 | #include <linux/device.h> |
| 18 | #include <linux/module.h> |
| 19 | #include <linux/pci.h> |
| 20 | #include <linux/scatterlist.h> |
| 21 | #include <linux/interrupt.h> |
| 22 | #include <linux/io.h> |
| 23 | #include <linux/pm.h> |
| 24 | #include <linux/mmc/host.h> |
| 25 | #include <linux/mmc/mmc.h> |
| 26 | |
| 27 | #include "toshsd.h" |
| 28 | |
| 29 | #define DRIVER_NAME "toshsd" |
| 30 | |
| 31 | static const struct pci_device_id pci_ids[] = { |
| 32 | { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA, 0x0805) }, |
| 33 | { /* end: all zeroes */ }, |
| 34 | }; |
| 35 | |
| 36 | MODULE_DEVICE_TABLE(pci, pci_ids); |
| 37 | |
| 38 | static void toshsd_init(struct toshsd_host *host) |
| 39 | { |
| 40 | /* enable clock */ |
| 41 | pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, |
| 42 | SD_PCICFG_CLKSTOP_ENABLE_ALL); |
| 43 | pci_write_config_byte(host->pdev, SD_PCICFG_CARDDETECT, 2); |
| 44 | |
| 45 | /* reset */ |
| 46 | iowrite16(0, host->ioaddr + SD_SOFTWARERESET); /* assert */ |
| 47 | mdelay(2); |
| 48 | iowrite16(1, host->ioaddr + SD_SOFTWARERESET); /* deassert */ |
| 49 | mdelay(2); |
| 50 | |
| 51 | /* Clear card registers */ |
| 52 | iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); |
| 53 | iowrite32(0, host->ioaddr + SD_CARDSTATUS); |
| 54 | iowrite32(0, host->ioaddr + SD_ERRORSTATUS0); |
| 55 | iowrite16(0, host->ioaddr + SD_STOPINTERNAL); |
| 56 | |
| 57 | /* SDIO clock? */ |
| 58 | iowrite16(0x100, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL); |
| 59 | |
| 60 | /* enable LED */ |
| 61 | pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE1, |
| 62 | SD_PCICFG_LED_ENABLE1_START); |
| 63 | pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE2, |
| 64 | SD_PCICFG_LED_ENABLE2_START); |
| 65 | |
| 66 | /* set interrupt masks */ |
| 67 | iowrite32(~(u32)(SD_CARD_RESP_END | SD_CARD_RW_END |
| 68 | | SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0 |
| 69 | | SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE |
| 70 | | SD_BUF_CMD_TIMEOUT), |
| 71 | host->ioaddr + SD_INTMASKCARD); |
| 72 | |
| 73 | iowrite16(0x1000, host->ioaddr + SD_TRANSACTIONCTRL); |
| 74 | } |
| 75 | |
| 76 | /* Set MMC clock / power. |
| 77 | * Note: This controller uses a simple divider scheme therefore it cannot run |
| 78 | * SD/MMC cards at full speed (24/20MHz). HCLK (=33MHz PCI clock?) is too high |
| 79 | * and the next slowest is 16MHz (div=2). |
| 80 | */ |
| 81 | static void __toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| 82 | { |
| 83 | struct toshsd_host *host = mmc_priv(mmc); |
| 84 | |
| 85 | if (ios->clock) { |
| 86 | u16 clk; |
| 87 | int div = 1; |
| 88 | |
| 89 | while (ios->clock < HCLK / div) |
| 90 | div *= 2; |
| 91 | |
| 92 | clk = div >> 2; |
| 93 | |
| 94 | if (div == 1) { /* disable the divider */ |
| 95 | pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, |
| 96 | SD_PCICFG_CLKMODE_DIV_DISABLE); |
| 97 | clk |= SD_CARDCLK_DIV_DISABLE; |
| 98 | } else |
| 99 | pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, 0); |
| 100 | |
| 101 | clk |= SD_CARDCLK_ENABLE_CLOCK; |
| 102 | iowrite16(clk, host->ioaddr + SD_CARDCLOCKCTRL); |
| 103 | |
| 104 | mdelay(10); |
| 105 | } else |
| 106 | iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); |
| 107 | |
| 108 | switch (ios->power_mode) { |
| 109 | case MMC_POWER_OFF: |
| 110 | pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, |
| 111 | SD_PCICFG_PWR1_OFF); |
| 112 | mdelay(1); |
| 113 | break; |
| 114 | case MMC_POWER_UP: |
| 115 | break; |
| 116 | case MMC_POWER_ON: |
| 117 | pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, |
| 118 | SD_PCICFG_PWR1_33V); |
| 119 | pci_write_config_byte(host->pdev, SD_PCICFG_POWER2, |
| 120 | SD_PCICFG_PWR2_AUTO); |
| 121 | mdelay(20); |
| 122 | break; |
| 123 | } |
| 124 | |
| 125 | switch (ios->bus_width) { |
| 126 | case MMC_BUS_WIDTH_1: |
| 127 | iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14) |
| 128 | | SD_CARDOPT_C2_MODULE_ABSENT |
| 129 | | SD_CARDOPT_DATA_XFR_WIDTH_1, |
| 130 | host->ioaddr + SD_CARDOPTIONSETUP); |
| 131 | break; |
| 132 | case MMC_BUS_WIDTH_4: |
| 133 | iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14) |
| 134 | | SD_CARDOPT_C2_MODULE_ABSENT |
| 135 | | SD_CARDOPT_DATA_XFR_WIDTH_4, |
| 136 | host->ioaddr + SD_CARDOPTIONSETUP); |
| 137 | break; |
| 138 | } |
| 139 | } |
| 140 | |
| 141 | static void toshsd_set_led(struct toshsd_host *host, unsigned char state) |
| 142 | { |
| 143 | iowrite16(state, host->ioaddr + SDIO_BASE + SDIO_LEDCTRL); |
| 144 | } |
| 145 | |
| 146 | static void toshsd_finish_request(struct toshsd_host *host) |
| 147 | { |
| 148 | struct mmc_request *mrq = host->mrq; |
| 149 | |
| 150 | /* Write something to end the command */ |
| 151 | host->mrq = NULL; |
| 152 | host->cmd = NULL; |
| 153 | host->data = NULL; |
| 154 | |
| 155 | toshsd_set_led(host, 0); |
| 156 | mmc_request_done(host->mmc, mrq); |
| 157 | } |
| 158 | |
| 159 | static irqreturn_t toshsd_thread_irq(int irq, void *dev_id) |
| 160 | { |
| 161 | struct toshsd_host *host = dev_id; |
| 162 | struct mmc_data *data = host->data; |
| 163 | struct sg_mapping_iter *sg_miter = &host->sg_miter; |
| 164 | unsigned short *buf; |
| 165 | int count; |
| 166 | unsigned long flags; |
| 167 | |
| 168 | if (!data) { |
| 169 | dev_warn(&host->pdev->dev, "Spurious Data IRQ\n"); |
| 170 | if (host->cmd) { |
| 171 | host->cmd->error = -EIO; |
| 172 | toshsd_finish_request(host); |
| 173 | } |
| 174 | return IRQ_NONE; |
| 175 | } |
| 176 | spin_lock_irqsave(&host->lock, flags); |
| 177 | |
| 178 | if (!sg_miter_next(sg_miter)) |
Axel Lin | 8a66fda | 2014-12-11 11:10:44 +0800 | [diff] [blame] | 179 | goto done; |
| 180 | |
Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 181 | buf = sg_miter->addr; |
| 182 | |
| 183 | /* Ensure we dont read more than one block. The chip will interrupt us |
| 184 | * When the next block is available. |
| 185 | */ |
| 186 | count = sg_miter->length; |
| 187 | if (count > data->blksz) |
| 188 | count = data->blksz; |
| 189 | |
| 190 | dev_dbg(&host->pdev->dev, "count: %08x, flags %08x\n", count, |
| 191 | data->flags); |
| 192 | |
| 193 | /* Transfer the data */ |
| 194 | if (data->flags & MMC_DATA_READ) |
| 195 | ioread32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2); |
| 196 | else |
| 197 | iowrite32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2); |
| 198 | |
| 199 | sg_miter->consumed = count; |
| 200 | sg_miter_stop(sg_miter); |
| 201 | |
Axel Lin | 8a66fda | 2014-12-11 11:10:44 +0800 | [diff] [blame] | 202 | done: |
Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 203 | spin_unlock_irqrestore(&host->lock, flags); |
| 204 | |
| 205 | return IRQ_HANDLED; |
| 206 | } |
| 207 | |
| 208 | static void toshsd_cmd_irq(struct toshsd_host *host) |
| 209 | { |
| 210 | struct mmc_command *cmd = host->cmd; |
Dan Carpenter | 9e2a0c9 | 2014-11-15 21:56:41 +0300 | [diff] [blame] | 211 | u8 *buf; |
Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 212 | u16 data; |
| 213 | |
| 214 | if (!host->cmd) { |
| 215 | dev_warn(&host->pdev->dev, "Spurious CMD irq\n"); |
| 216 | return; |
| 217 | } |
Dan Carpenter | 9e2a0c9 | 2014-11-15 21:56:41 +0300 | [diff] [blame] | 218 | buf = (u8 *)cmd->resp; |
Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 219 | host->cmd = NULL; |
| 220 | |
| 221 | if (cmd->flags & MMC_RSP_PRESENT && cmd->flags & MMC_RSP_136) { |
| 222 | /* R2 */ |
| 223 | buf[12] = 0xff; |
| 224 | data = ioread16(host->ioaddr + SD_RESPONSE0); |
| 225 | buf[13] = data & 0xff; |
| 226 | buf[14] = data >> 8; |
| 227 | data = ioread16(host->ioaddr + SD_RESPONSE1); |
| 228 | buf[15] = data & 0xff; |
| 229 | buf[8] = data >> 8; |
| 230 | data = ioread16(host->ioaddr + SD_RESPONSE2); |
| 231 | buf[9] = data & 0xff; |
| 232 | buf[10] = data >> 8; |
| 233 | data = ioread16(host->ioaddr + SD_RESPONSE3); |
| 234 | buf[11] = data & 0xff; |
| 235 | buf[4] = data >> 8; |
| 236 | data = ioread16(host->ioaddr + SD_RESPONSE4); |
| 237 | buf[5] = data & 0xff; |
| 238 | buf[6] = data >> 8; |
| 239 | data = ioread16(host->ioaddr + SD_RESPONSE5); |
| 240 | buf[7] = data & 0xff; |
| 241 | buf[0] = data >> 8; |
| 242 | data = ioread16(host->ioaddr + SD_RESPONSE6); |
| 243 | buf[1] = data & 0xff; |
| 244 | buf[2] = data >> 8; |
| 245 | data = ioread16(host->ioaddr + SD_RESPONSE7); |
| 246 | buf[3] = data & 0xff; |
| 247 | } else if (cmd->flags & MMC_RSP_PRESENT) { |
| 248 | /* R1, R1B, R3, R6, R7 */ |
| 249 | data = ioread16(host->ioaddr + SD_RESPONSE0); |
| 250 | buf[0] = data & 0xff; |
| 251 | buf[1] = data >> 8; |
| 252 | data = ioread16(host->ioaddr + SD_RESPONSE1); |
| 253 | buf[2] = data & 0xff; |
| 254 | buf[3] = data >> 8; |
| 255 | } |
| 256 | |
| 257 | dev_dbg(&host->pdev->dev, "Command IRQ complete %d %d %x\n", |
| 258 | cmd->opcode, cmd->error, cmd->flags); |
| 259 | |
| 260 | /* If there is data to handle we will |
| 261 | * finish the request in the mmc_data_end_irq handler.*/ |
| 262 | if (host->data) |
| 263 | return; |
| 264 | |
| 265 | toshsd_finish_request(host); |
| 266 | } |
| 267 | |
| 268 | static void toshsd_data_end_irq(struct toshsd_host *host) |
| 269 | { |
| 270 | struct mmc_data *data = host->data; |
| 271 | |
| 272 | host->data = NULL; |
| 273 | |
| 274 | if (!data) { |
| 275 | dev_warn(&host->pdev->dev, "Spurious data end IRQ\n"); |
| 276 | return; |
| 277 | } |
| 278 | |
| 279 | if (data->error == 0) |
| 280 | data->bytes_xfered = data->blocks * data->blksz; |
| 281 | else |
| 282 | data->bytes_xfered = 0; |
| 283 | |
| 284 | dev_dbg(&host->pdev->dev, "Completed data request xfr=%d\n", |
| 285 | data->bytes_xfered); |
| 286 | |
| 287 | iowrite16(0, host->ioaddr + SD_STOPINTERNAL); |
| 288 | |
| 289 | toshsd_finish_request(host); |
| 290 | } |
| 291 | |
| 292 | static irqreturn_t toshsd_irq(int irq, void *dev_id) |
| 293 | { |
| 294 | struct toshsd_host *host = dev_id; |
| 295 | u32 int_reg, int_mask, int_status, detail; |
| 296 | int error = 0, ret = IRQ_HANDLED; |
| 297 | |
| 298 | spin_lock(&host->lock); |
| 299 | int_status = ioread32(host->ioaddr + SD_CARDSTATUS); |
| 300 | int_mask = ioread32(host->ioaddr + SD_INTMASKCARD); |
| 301 | int_reg = int_status & ~int_mask & ~IRQ_DONT_CARE_BITS; |
| 302 | |
| 303 | dev_dbg(&host->pdev->dev, "IRQ status:%x mask:%x\n", |
| 304 | int_status, int_mask); |
| 305 | |
| 306 | /* nothing to do: it's not our IRQ */ |
| 307 | if (!int_reg) { |
| 308 | ret = IRQ_NONE; |
| 309 | goto irq_end; |
| 310 | } |
| 311 | |
| 312 | if (int_reg & SD_BUF_CMD_TIMEOUT) { |
| 313 | error = -ETIMEDOUT; |
| 314 | dev_dbg(&host->pdev->dev, "Timeout\n"); |
| 315 | } else if (int_reg & SD_BUF_CRC_ERR) { |
| 316 | error = -EILSEQ; |
| 317 | dev_err(&host->pdev->dev, "BadCRC\n"); |
| 318 | } else if (int_reg & (SD_BUF_ILLEGAL_ACCESS |
| 319 | | SD_BUF_CMD_INDEX_ERR |
| 320 | | SD_BUF_STOP_BIT_END_ERR |
| 321 | | SD_BUF_OVERFLOW |
| 322 | | SD_BUF_UNDERFLOW |
| 323 | | SD_BUF_DATA_TIMEOUT)) { |
| 324 | dev_err(&host->pdev->dev, "Buffer status error: { %s%s%s%s%s%s}\n", |
| 325 | int_reg & SD_BUF_ILLEGAL_ACCESS ? "ILLEGAL_ACC " : "", |
| 326 | int_reg & SD_BUF_CMD_INDEX_ERR ? "CMD_INDEX " : "", |
| 327 | int_reg & SD_BUF_STOP_BIT_END_ERR ? "STOPBIT_END " : "", |
| 328 | int_reg & SD_BUF_OVERFLOW ? "OVERFLOW " : "", |
| 329 | int_reg & SD_BUF_UNDERFLOW ? "UNDERFLOW " : "", |
| 330 | int_reg & SD_BUF_DATA_TIMEOUT ? "DATA_TIMEOUT " : ""); |
| 331 | |
| 332 | detail = ioread32(host->ioaddr + SD_ERRORSTATUS0); |
| 333 | dev_err(&host->pdev->dev, "detail error status { %s%s%s%s%s%s%s%s%s%s%s%s%s}\n", |
| 334 | detail & SD_ERR0_RESP_CMD_ERR ? "RESP_CMD " : "", |
| 335 | detail & SD_ERR0_RESP_NON_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "", |
| 336 | detail & SD_ERR0_RESP_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "", |
| 337 | detail & SD_ERR0_READ_DATA_END_BIT_ERR ? "READ_DATA_END_BIT " : "", |
| 338 | detail & SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR ? "WRITE_CMD_END_BIT " : "", |
| 339 | detail & SD_ERR0_RESP_NON_CMD12_CRC_ERR ? "RESP_CRC " : "", |
| 340 | detail & SD_ERR0_RESP_CMD12_CRC_ERR ? "RESP_CRC " : "", |
| 341 | detail & SD_ERR0_READ_DATA_CRC_ERR ? "READ_DATA_CRC " : "", |
| 342 | detail & SD_ERR0_WRITE_CMD_CRC_ERR ? "WRITE_CMD_CRC " : "", |
| 343 | detail & SD_ERR1_NO_CMD_RESP ? "NO_CMD_RESP " : "", |
| 344 | detail & SD_ERR1_TIMEOUT_READ_DATA ? "READ_DATA_TIMEOUT " : "", |
| 345 | detail & SD_ERR1_TIMEOUT_CRS_STATUS ? "CRS_STATUS_TIMEOUT " : "", |
| 346 | detail & SD_ERR1_TIMEOUT_CRC_BUSY ? "CRC_BUSY_TIMEOUT " : ""); |
| 347 | error = -EIO; |
| 348 | } |
| 349 | |
| 350 | if (error) { |
| 351 | if (host->cmd) |
| 352 | host->cmd->error = error; |
| 353 | |
| 354 | if (error == -ETIMEDOUT) { |
| 355 | iowrite32(int_status & |
| 356 | ~(SD_BUF_CMD_TIMEOUT | SD_CARD_RESP_END), |
| 357 | host->ioaddr + SD_CARDSTATUS); |
| 358 | } else { |
| 359 | toshsd_init(host); |
| 360 | __toshsd_set_ios(host->mmc, &host->mmc->ios); |
| 361 | goto irq_end; |
| 362 | } |
| 363 | } |
| 364 | |
| 365 | /* Card insert/remove. The mmc controlling code is stateless. */ |
| 366 | if (int_reg & (SD_CARD_CARD_INSERTED_0 | SD_CARD_CARD_REMOVED_0)) { |
| 367 | iowrite32(int_status & |
| 368 | ~(SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0), |
| 369 | host->ioaddr + SD_CARDSTATUS); |
| 370 | |
| 371 | if (int_reg & SD_CARD_CARD_INSERTED_0) |
| 372 | toshsd_init(host); |
| 373 | |
| 374 | mmc_detect_change(host->mmc, 1); |
| 375 | } |
| 376 | |
| 377 | /* Data transfer */ |
| 378 | if (int_reg & (SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE)) { |
| 379 | iowrite32(int_status & |
| 380 | ~(SD_BUF_WRITE_ENABLE | SD_BUF_READ_ENABLE), |
| 381 | host->ioaddr + SD_CARDSTATUS); |
| 382 | |
| 383 | ret = IRQ_WAKE_THREAD; |
| 384 | goto irq_end; |
| 385 | } |
| 386 | |
| 387 | /* Command completion */ |
| 388 | if (int_reg & SD_CARD_RESP_END) { |
| 389 | iowrite32(int_status & ~(SD_CARD_RESP_END), |
| 390 | host->ioaddr + SD_CARDSTATUS); |
| 391 | toshsd_cmd_irq(host); |
| 392 | } |
| 393 | |
| 394 | /* Data transfer completion */ |
| 395 | if (int_reg & SD_CARD_RW_END) { |
| 396 | iowrite32(int_status & ~(SD_CARD_RW_END), |
| 397 | host->ioaddr + SD_CARDSTATUS); |
| 398 | toshsd_data_end_irq(host); |
| 399 | } |
| 400 | irq_end: |
| 401 | spin_unlock(&host->lock); |
| 402 | return ret; |
| 403 | } |
| 404 | |
| 405 | static void toshsd_start_cmd(struct toshsd_host *host, struct mmc_command *cmd) |
| 406 | { |
| 407 | struct mmc_data *data = host->data; |
| 408 | int c = cmd->opcode; |
| 409 | |
| 410 | dev_dbg(&host->pdev->dev, "Command opcode: %d\n", cmd->opcode); |
| 411 | |
| 412 | if (cmd->opcode == MMC_STOP_TRANSMISSION) { |
| 413 | iowrite16(SD_STOPINT_ISSUE_CMD12, |
| 414 | host->ioaddr + SD_STOPINTERNAL); |
| 415 | |
| 416 | cmd->resp[0] = cmd->opcode; |
| 417 | cmd->resp[1] = 0; |
| 418 | cmd->resp[2] = 0; |
| 419 | cmd->resp[3] = 0; |
| 420 | |
| 421 | toshsd_finish_request(host); |
| 422 | return; |
| 423 | } |
| 424 | |
| 425 | switch (mmc_resp_type(cmd)) { |
| 426 | case MMC_RSP_NONE: |
| 427 | c |= SD_CMD_RESP_TYPE_NONE; |
| 428 | break; |
| 429 | |
| 430 | case MMC_RSP_R1: |
| 431 | c |= SD_CMD_RESP_TYPE_EXT_R1; |
| 432 | break; |
| 433 | case MMC_RSP_R1B: |
| 434 | c |= SD_CMD_RESP_TYPE_EXT_R1B; |
| 435 | break; |
| 436 | case MMC_RSP_R2: |
| 437 | c |= SD_CMD_RESP_TYPE_EXT_R2; |
| 438 | break; |
| 439 | case MMC_RSP_R3: |
| 440 | c |= SD_CMD_RESP_TYPE_EXT_R3; |
| 441 | break; |
| 442 | |
| 443 | default: |
| 444 | dev_err(&host->pdev->dev, "Unknown response type %d\n", |
| 445 | mmc_resp_type(cmd)); |
| 446 | break; |
| 447 | } |
| 448 | |
| 449 | host->cmd = cmd; |
| 450 | |
| 451 | if (cmd->opcode == MMC_APP_CMD) |
| 452 | c |= SD_CMD_TYPE_ACMD; |
| 453 | |
| 454 | if (cmd->opcode == MMC_GO_IDLE_STATE) |
| 455 | c |= (3 << 8); /* removed from ipaq-asic3.h for some reason */ |
| 456 | |
| 457 | if (data) { |
| 458 | c |= SD_CMD_DATA_PRESENT; |
| 459 | |
| 460 | if (data->blocks > 1) { |
| 461 | iowrite16(SD_STOPINT_AUTO_ISSUE_CMD12, |
| 462 | host->ioaddr + SD_STOPINTERNAL); |
| 463 | c |= SD_CMD_MULTI_BLOCK; |
| 464 | } |
| 465 | |
| 466 | if (data->flags & MMC_DATA_READ) |
| 467 | c |= SD_CMD_TRANSFER_READ; |
| 468 | |
| 469 | /* MMC_DATA_WRITE does not require a bit to be set */ |
| 470 | } |
| 471 | |
| 472 | /* Send the command */ |
| 473 | iowrite32(cmd->arg, host->ioaddr + SD_ARG0); |
| 474 | iowrite16(c, host->ioaddr + SD_CMD); |
| 475 | } |
| 476 | |
| 477 | static void toshsd_start_data(struct toshsd_host *host, struct mmc_data *data) |
| 478 | { |
| 479 | unsigned int flags = SG_MITER_ATOMIC; |
| 480 | |
| 481 | dev_dbg(&host->pdev->dev, "setup data transfer: blocksize %08x nr_blocks %d, offset: %08x\n", |
| 482 | data->blksz, data->blocks, data->sg->offset); |
| 483 | |
| 484 | host->data = data; |
| 485 | |
| 486 | if (data->flags & MMC_DATA_READ) |
| 487 | flags |= SG_MITER_TO_SG; |
| 488 | else |
| 489 | flags |= SG_MITER_FROM_SG; |
| 490 | |
| 491 | sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); |
| 492 | |
| 493 | /* Set transfer length and blocksize */ |
| 494 | iowrite16(data->blocks, host->ioaddr + SD_BLOCKCOUNT); |
| 495 | iowrite16(data->blksz, host->ioaddr + SD_CARDXFERDATALEN); |
| 496 | } |
| 497 | |
| 498 | /* Process requests from the MMC layer */ |
| 499 | static void toshsd_request(struct mmc_host *mmc, struct mmc_request *mrq) |
| 500 | { |
| 501 | struct toshsd_host *host = mmc_priv(mmc); |
| 502 | unsigned long flags; |
| 503 | |
| 504 | /* abort if card not present */ |
| 505 | if (!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0)) { |
| 506 | mrq->cmd->error = -ENOMEDIUM; |
| 507 | mmc_request_done(mmc, mrq); |
| 508 | return; |
| 509 | } |
| 510 | |
| 511 | spin_lock_irqsave(&host->lock, flags); |
| 512 | |
| 513 | WARN_ON(host->mrq != NULL); |
| 514 | |
| 515 | host->mrq = mrq; |
| 516 | |
| 517 | if (mrq->data) |
| 518 | toshsd_start_data(host, mrq->data); |
| 519 | |
| 520 | toshsd_set_led(host, 1); |
| 521 | |
| 522 | toshsd_start_cmd(host, mrq->cmd); |
| 523 | |
| 524 | spin_unlock_irqrestore(&host->lock, flags); |
| 525 | } |
| 526 | |
| 527 | static void toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) |
| 528 | { |
| 529 | struct toshsd_host *host = mmc_priv(mmc); |
| 530 | unsigned long flags; |
| 531 | |
| 532 | spin_lock_irqsave(&host->lock, flags); |
| 533 | __toshsd_set_ios(mmc, ios); |
| 534 | spin_unlock_irqrestore(&host->lock, flags); |
| 535 | } |
| 536 | |
| 537 | static int toshsd_get_ro(struct mmc_host *mmc) |
| 538 | { |
| 539 | struct toshsd_host *host = mmc_priv(mmc); |
| 540 | |
| 541 | /* active low */ |
| 542 | return !(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_WRITE_PROTECT); |
| 543 | } |
| 544 | |
| 545 | static int toshsd_get_cd(struct mmc_host *mmc) |
| 546 | { |
| 547 | struct toshsd_host *host = mmc_priv(mmc); |
| 548 | |
| 549 | return !!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0); |
| 550 | } |
| 551 | |
| 552 | static struct mmc_host_ops toshsd_ops = { |
| 553 | .request = toshsd_request, |
| 554 | .set_ios = toshsd_set_ios, |
| 555 | .get_ro = toshsd_get_ro, |
| 556 | .get_cd = toshsd_get_cd, |
| 557 | }; |
| 558 | |
| 559 | |
| 560 | static void toshsd_powerdown(struct toshsd_host *host) |
| 561 | { |
| 562 | /* mask all interrupts */ |
| 563 | iowrite32(0xffffffff, host->ioaddr + SD_INTMASKCARD); |
| 564 | /* disable card clock */ |
| 565 | iowrite16(0x000, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL); |
| 566 | iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL); |
| 567 | /* power down card */ |
| 568 | pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, SD_PCICFG_PWR1_OFF); |
| 569 | /* disable clock */ |
| 570 | pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, 0); |
| 571 | } |
| 572 | |
| 573 | #ifdef CONFIG_PM_SLEEP |
| 574 | static int toshsd_pm_suspend(struct device *dev) |
| 575 | { |
| 576 | struct pci_dev *pdev = to_pci_dev(dev); |
| 577 | struct toshsd_host *host = pci_get_drvdata(pdev); |
| 578 | |
| 579 | toshsd_powerdown(host); |
| 580 | |
| 581 | pci_save_state(pdev); |
| 582 | pci_enable_wake(pdev, PCI_D3hot, 0); |
| 583 | pci_disable_device(pdev); |
| 584 | pci_set_power_state(pdev, PCI_D3hot); |
| 585 | |
| 586 | return 0; |
| 587 | } |
| 588 | |
| 589 | static int toshsd_pm_resume(struct device *dev) |
| 590 | { |
| 591 | struct pci_dev *pdev = to_pci_dev(dev); |
| 592 | struct toshsd_host *host = pci_get_drvdata(pdev); |
| 593 | int ret; |
| 594 | |
| 595 | pci_set_power_state(pdev, PCI_D0); |
| 596 | pci_restore_state(pdev); |
| 597 | ret = pci_enable_device(pdev); |
| 598 | if (ret) |
| 599 | return ret; |
| 600 | |
| 601 | toshsd_init(host); |
| 602 | |
| 603 | return 0; |
| 604 | } |
| 605 | #endif /* CONFIG_PM_SLEEP */ |
| 606 | |
| 607 | static int toshsd_probe(struct pci_dev *pdev, const struct pci_device_id *ent) |
| 608 | { |
| 609 | int ret; |
| 610 | struct toshsd_host *host; |
| 611 | struct mmc_host *mmc; |
| 612 | resource_size_t base; |
| 613 | |
| 614 | ret = pci_enable_device(pdev); |
| 615 | if (ret) |
| 616 | return ret; |
| 617 | |
| 618 | mmc = mmc_alloc_host(sizeof(struct toshsd_host), &pdev->dev); |
| 619 | if (!mmc) { |
| 620 | ret = -ENOMEM; |
| 621 | goto err; |
| 622 | } |
| 623 | |
| 624 | host = mmc_priv(mmc); |
| 625 | host->mmc = mmc; |
| 626 | |
| 627 | host->pdev = pdev; |
| 628 | pci_set_drvdata(pdev, host); |
| 629 | |
| 630 | ret = pci_request_regions(pdev, DRIVER_NAME); |
| 631 | if (ret) |
| 632 | goto free; |
| 633 | |
| 634 | host->ioaddr = pci_iomap(pdev, 0, 0); |
| 635 | if (!host->ioaddr) { |
| 636 | ret = -ENOMEM; |
| 637 | goto release; |
| 638 | } |
| 639 | |
| 640 | /* Set MMC host parameters */ |
| 641 | mmc->ops = &toshsd_ops; |
| 642 | mmc->caps = MMC_CAP_4_BIT_DATA; |
| 643 | mmc->ocr_avail = MMC_VDD_32_33; |
| 644 | |
| 645 | mmc->f_min = HCLK / 512; |
| 646 | mmc->f_max = HCLK; |
| 647 | |
| 648 | spin_lock_init(&host->lock); |
| 649 | |
| 650 | toshsd_init(host); |
| 651 | |
| 652 | ret = request_threaded_irq(pdev->irq, toshsd_irq, toshsd_thread_irq, |
| 653 | IRQF_SHARED, DRIVER_NAME, host); |
| 654 | if (ret) |
| 655 | goto unmap; |
| 656 | |
| 657 | mmc_add_host(mmc); |
| 658 | |
| 659 | base = pci_resource_start(pdev, 0); |
| 660 | dev_dbg(&pdev->dev, "MMIO %pa, IRQ %d\n", &base, pdev->irq); |
| 661 | |
| 662 | pm_suspend_ignore_children(&pdev->dev, 1); |
| 663 | |
| 664 | return 0; |
| 665 | |
| 666 | unmap: |
| 667 | pci_iounmap(pdev, host->ioaddr); |
| 668 | release: |
| 669 | pci_release_regions(pdev); |
| 670 | free: |
| 671 | mmc_free_host(mmc); |
| 672 | pci_set_drvdata(pdev, NULL); |
| 673 | err: |
| 674 | pci_disable_device(pdev); |
| 675 | return ret; |
| 676 | } |
| 677 | |
| 678 | static void toshsd_remove(struct pci_dev *pdev) |
| 679 | { |
| 680 | struct toshsd_host *host = pci_get_drvdata(pdev); |
| 681 | |
| 682 | mmc_remove_host(host->mmc); |
| 683 | toshsd_powerdown(host); |
| 684 | free_irq(pdev->irq, host); |
| 685 | pci_iounmap(pdev, host->ioaddr); |
| 686 | pci_release_regions(pdev); |
| 687 | mmc_free_host(host->mmc); |
| 688 | pci_set_drvdata(pdev, NULL); |
| 689 | pci_disable_device(pdev); |
| 690 | } |
| 691 | |
| 692 | static const struct dev_pm_ops toshsd_pm_ops = { |
| 693 | SET_SYSTEM_SLEEP_PM_OPS(toshsd_pm_suspend, toshsd_pm_resume) |
| 694 | }; |
| 695 | |
| 696 | static struct pci_driver toshsd_driver = { |
| 697 | .name = DRIVER_NAME, |
| 698 | .id_table = pci_ids, |
| 699 | .probe = toshsd_probe, |
| 700 | .remove = toshsd_remove, |
| 701 | .driver.pm = &toshsd_pm_ops, |
| 702 | }; |
| 703 | |
Wei Yongjun | 1818681 | 2014-12-09 09:08:05 +0800 | [diff] [blame] | 704 | module_pci_driver(toshsd_driver); |
Ondrej Zary | a5eb8bb | 2014-11-11 17:54:55 +0100 | [diff] [blame] | 705 | |
| 706 | MODULE_AUTHOR("Ondrej Zary, Richard Betts"); |
| 707 | MODULE_DESCRIPTION("Toshiba PCI Secure Digital Host Controller Interface driver"); |
| 708 | MODULE_LICENSE("GPL"); |