Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 1 | /* |
| 2 | * linux/arch/arm/common/locomo.c |
| 3 | * |
| 4 | * Sharp LoCoMo support |
| 5 | * |
| 6 | * This program is free software; you can redistribute it and/or modify |
| 7 | * it under the terms of the GNU General Public License version 2 as |
| 8 | * published by the Free Software Foundation. |
| 9 | * |
| 10 | * This file contains all generic LoCoMo support. |
| 11 | * |
| 12 | * All initialization functions provided here are intended to be called |
| 13 | * from machine specific code with proper arguments when required. |
| 14 | * |
| 15 | * Based on sa1111.c |
| 16 | */ |
| 17 | |
| 18 | #include <linux/config.h> |
| 19 | #include <linux/module.h> |
| 20 | #include <linux/init.h> |
| 21 | #include <linux/kernel.h> |
| 22 | #include <linux/delay.h> |
| 23 | #include <linux/errno.h> |
| 24 | #include <linux/ioport.h> |
| 25 | #include <linux/device.h> |
| 26 | #include <linux/slab.h> |
| 27 | #include <linux/spinlock.h> |
| 28 | |
| 29 | #include <asm/hardware.h> |
| 30 | #include <asm/mach-types.h> |
| 31 | #include <asm/io.h> |
| 32 | #include <asm/irq.h> |
| 33 | #include <asm/mach/irq.h> |
| 34 | |
| 35 | #include <asm/hardware/locomo.h> |
| 36 | |
| 37 | /* M62332 output channel selection */ |
| 38 | #define M62332_EVR_CH 1 /* M62332 volume channel number */ |
| 39 | /* 0 : CH.1 , 1 : CH. 2 */ |
| 40 | /* DAC send data */ |
| 41 | #define M62332_SLAVE_ADDR 0x4e /* Slave address */ |
| 42 | #define M62332_W_BIT 0x00 /* W bit (0 only) */ |
| 43 | #define M62332_SUB_ADDR 0x00 /* Sub address */ |
| 44 | #define M62332_A_BIT 0x00 /* A bit (0 only) */ |
| 45 | |
| 46 | /* DAC setup and hold times (expressed in us) */ |
| 47 | #define DAC_BUS_FREE_TIME 5 /* 4.7 us */ |
| 48 | #define DAC_START_SETUP_TIME 5 /* 4.7 us */ |
| 49 | #define DAC_STOP_SETUP_TIME 4 /* 4.0 us */ |
| 50 | #define DAC_START_HOLD_TIME 5 /* 4.7 us */ |
| 51 | #define DAC_SCL_LOW_HOLD_TIME 5 /* 4.7 us */ |
| 52 | #define DAC_SCL_HIGH_HOLD_TIME 4 /* 4.0 us */ |
| 53 | #define DAC_DATA_SETUP_TIME 1 /* 250 ns */ |
| 54 | #define DAC_DATA_HOLD_TIME 1 /* 300 ns */ |
| 55 | #define DAC_LOW_SETUP_TIME 1 /* 300 ns */ |
| 56 | #define DAC_HIGH_SETUP_TIME 1 /* 1000 ns */ |
| 57 | |
| 58 | /* the following is the overall data for the locomo chip */ |
| 59 | struct locomo { |
| 60 | struct device *dev; |
| 61 | unsigned long phys; |
| 62 | unsigned int irq; |
| 63 | spinlock_t lock; |
| 64 | void *base; |
| 65 | }; |
| 66 | |
| 67 | struct locomo_dev_info { |
| 68 | unsigned long offset; |
| 69 | unsigned long length; |
| 70 | unsigned int devid; |
| 71 | unsigned int irq[1]; |
| 72 | const char * name; |
| 73 | }; |
| 74 | |
| 75 | /* All the locomo devices. If offset is non-zero, the mapbase for the |
| 76 | * locomo_dev will be set to the chip base plus offset. If offset is |
| 77 | * zero, then the mapbase for the locomo_dev will be set to zero. An |
| 78 | * offset of zero means the device only uses GPIOs or other helper |
| 79 | * functions inside this file */ |
| 80 | static struct locomo_dev_info locomo_devices[] = { |
| 81 | { |
| 82 | .devid = LOCOMO_DEVID_KEYBOARD, |
| 83 | .irq = { |
| 84 | IRQ_LOCOMO_KEY, |
| 85 | }, |
| 86 | .name = "locomo-keyboard", |
| 87 | .offset = LOCOMO_KEYBOARD, |
| 88 | .length = 16, |
| 89 | }, |
| 90 | { |
| 91 | .devid = LOCOMO_DEVID_FRONTLIGHT, |
| 92 | .irq = {}, |
| 93 | .name = "locomo-frontlight", |
| 94 | .offset = LOCOMO_FRONTLIGHT, |
| 95 | .length = 8, |
| 96 | |
| 97 | }, |
| 98 | { |
| 99 | .devid = LOCOMO_DEVID_BACKLIGHT, |
| 100 | .irq = {}, |
| 101 | .name = "locomo-backlight", |
| 102 | .offset = LOCOMO_BACKLIGHT, |
| 103 | .length = 8, |
| 104 | }, |
| 105 | { |
| 106 | .devid = LOCOMO_DEVID_AUDIO, |
| 107 | .irq = {}, |
| 108 | .name = "locomo-audio", |
| 109 | .offset = LOCOMO_AUDIO, |
| 110 | .length = 4, |
| 111 | }, |
| 112 | { |
| 113 | .devid = LOCOMO_DEVID_LED, |
| 114 | .irq = {}, |
| 115 | .name = "locomo-led", |
| 116 | .offset = LOCOMO_LED, |
| 117 | .length = 8, |
| 118 | }, |
| 119 | { |
| 120 | .devid = LOCOMO_DEVID_UART, |
| 121 | .irq = {}, |
| 122 | .name = "locomo-uart", |
| 123 | .offset = 0, |
| 124 | .length = 0, |
| 125 | }, |
| 126 | }; |
| 127 | |
| 128 | |
| 129 | /** LoCoMo interrupt handling stuff. |
| 130 | * NOTE: LoCoMo has a 1 to many mapping on all of its IRQs. |
| 131 | * that is, there is only one real hardware interrupt |
| 132 | * we determine which interrupt it is by reading some IO memory. |
| 133 | * We have two levels of expansion, first in the handler for the |
| 134 | * hardware interrupt we generate an interrupt |
| 135 | * IRQ_LOCOMO_*_BASE and those handlers generate more interrupts |
| 136 | * |
| 137 | * hardware irq reads LOCOMO_ICR & 0x0f00 |
| 138 | * IRQ_LOCOMO_KEY_BASE |
| 139 | * IRQ_LOCOMO_GPIO_BASE |
| 140 | * IRQ_LOCOMO_LT_BASE |
| 141 | * IRQ_LOCOMO_SPI_BASE |
| 142 | * IRQ_LOCOMO_KEY_BASE reads LOCOMO_KIC & 0x0001 |
| 143 | * IRQ_LOCOMO_KEY |
| 144 | * IRQ_LOCOMO_GPIO_BASE reads LOCOMO_GIR & LOCOMO_GPD & 0xffff |
| 145 | * IRQ_LOCOMO_GPIO[0-15] |
| 146 | * IRQ_LOCOMO_LT_BASE reads LOCOMO_LTINT & 0x0001 |
| 147 | * IRQ_LOCOMO_LT |
| 148 | * IRQ_LOCOMO_SPI_BASE reads LOCOMO_SPIIR & 0x000F |
| 149 | * IRQ_LOCOMO_SPI_RFR |
| 150 | * IRQ_LOCOMO_SPI_RFW |
| 151 | * IRQ_LOCOMO_SPI_OVRN |
| 152 | * IRQ_LOCOMO_SPI_TEND |
| 153 | */ |
| 154 | |
| 155 | #define LOCOMO_IRQ_START (IRQ_LOCOMO_KEY_BASE) |
| 156 | #define LOCOMO_IRQ_KEY_START (IRQ_LOCOMO_KEY) |
| 157 | #define LOCOMO_IRQ_GPIO_START (IRQ_LOCOMO_GPIO0) |
| 158 | #define LOCOMO_IRQ_LT_START (IRQ_LOCOMO_LT) |
| 159 | #define LOCOMO_IRQ_SPI_START (IRQ_LOCOMO_SPI_RFR) |
| 160 | |
| 161 | static void locomo_handler(unsigned int irq, struct irqdesc *desc, |
| 162 | struct pt_regs *regs) |
| 163 | { |
| 164 | int req, i; |
| 165 | struct irqdesc *d; |
| 166 | void *mapbase = get_irq_chipdata(irq); |
| 167 | |
| 168 | /* Acknowledge the parent IRQ */ |
| 169 | desc->chip->ack(irq); |
| 170 | |
| 171 | /* check why this interrupt was generated */ |
| 172 | req = locomo_readl(mapbase + LOCOMO_ICR) & 0x0f00; |
| 173 | |
| 174 | if (req) { |
| 175 | /* generate the next interrupt(s) */ |
| 176 | irq = LOCOMO_IRQ_START; |
| 177 | d = irq_desc + irq; |
| 178 | for (i = 0; i <= 3; i++, d++, irq++) { |
| 179 | if (req & (0x0100 << i)) { |
| 180 | d->handle(irq, d, regs); |
| 181 | } |
| 182 | |
| 183 | } |
| 184 | } |
| 185 | } |
| 186 | |
| 187 | static void locomo_ack_irq(unsigned int irq) |
| 188 | { |
| 189 | } |
| 190 | |
| 191 | static void locomo_mask_irq(unsigned int irq) |
| 192 | { |
| 193 | void *mapbase = get_irq_chipdata(irq); |
| 194 | unsigned int r; |
| 195 | r = locomo_readl(mapbase + LOCOMO_ICR); |
| 196 | r &= ~(0x0010 << (irq - LOCOMO_IRQ_START)); |
| 197 | locomo_writel(r, mapbase + LOCOMO_ICR); |
| 198 | } |
| 199 | |
| 200 | static void locomo_unmask_irq(unsigned int irq) |
| 201 | { |
| 202 | void *mapbase = get_irq_chipdata(irq); |
| 203 | unsigned int r; |
| 204 | r = locomo_readl(mapbase + LOCOMO_ICR); |
| 205 | r |= (0x0010 << (irq - LOCOMO_IRQ_START)); |
| 206 | locomo_writel(r, mapbase + LOCOMO_ICR); |
| 207 | } |
| 208 | |
| 209 | static struct irqchip locomo_chip = { |
| 210 | .ack = locomo_ack_irq, |
| 211 | .mask = locomo_mask_irq, |
| 212 | .unmask = locomo_unmask_irq, |
| 213 | }; |
| 214 | |
| 215 | static void locomo_key_handler(unsigned int irq, struct irqdesc *desc, |
| 216 | struct pt_regs *regs) |
| 217 | { |
| 218 | struct irqdesc *d; |
| 219 | void *mapbase = get_irq_chipdata(irq); |
| 220 | |
| 221 | if (locomo_readl(mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC) & 0x0001) { |
| 222 | d = irq_desc + LOCOMO_IRQ_KEY_START; |
| 223 | d->handle(LOCOMO_IRQ_KEY_START, d, regs); |
| 224 | } |
| 225 | } |
| 226 | |
| 227 | static void locomo_key_ack_irq(unsigned int irq) |
| 228 | { |
| 229 | void *mapbase = get_irq_chipdata(irq); |
| 230 | unsigned int r; |
| 231 | r = locomo_readl(mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 232 | r &= ~(0x0100 << (irq - LOCOMO_IRQ_KEY_START)); |
| 233 | locomo_writel(r, mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 234 | } |
| 235 | |
| 236 | static void locomo_key_mask_irq(unsigned int irq) |
| 237 | { |
| 238 | void *mapbase = get_irq_chipdata(irq); |
| 239 | unsigned int r; |
| 240 | r = locomo_readl(mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 241 | r &= ~(0x0010 << (irq - LOCOMO_IRQ_KEY_START)); |
| 242 | locomo_writel(r, mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 243 | } |
| 244 | |
| 245 | static void locomo_key_unmask_irq(unsigned int irq) |
| 246 | { |
| 247 | void *mapbase = get_irq_chipdata(irq); |
| 248 | unsigned int r; |
| 249 | r = locomo_readl(mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 250 | r |= (0x0010 << (irq - LOCOMO_IRQ_KEY_START)); |
| 251 | locomo_writel(r, mapbase + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 252 | } |
| 253 | |
| 254 | static struct irqchip locomo_key_chip = { |
| 255 | .ack = locomo_key_ack_irq, |
| 256 | .mask = locomo_key_mask_irq, |
| 257 | .unmask = locomo_key_unmask_irq, |
| 258 | }; |
| 259 | |
| 260 | static void locomo_gpio_handler(unsigned int irq, struct irqdesc *desc, |
| 261 | struct pt_regs *regs) |
| 262 | { |
| 263 | int req, i; |
| 264 | struct irqdesc *d; |
| 265 | void *mapbase = get_irq_chipdata(irq); |
| 266 | |
| 267 | req = locomo_readl(mapbase + LOCOMO_GIR) & |
| 268 | locomo_readl(mapbase + LOCOMO_GPD) & |
| 269 | 0xffff; |
| 270 | |
| 271 | if (req) { |
| 272 | irq = LOCOMO_IRQ_GPIO_START; |
| 273 | d = irq_desc + LOCOMO_IRQ_GPIO_START; |
| 274 | for (i = 0; i <= 15; i++, irq++, d++) { |
| 275 | if (req & (0x0001 << i)) { |
| 276 | d->handle(irq, d, regs); |
| 277 | } |
| 278 | } |
| 279 | } |
| 280 | } |
| 281 | |
| 282 | static void locomo_gpio_ack_irq(unsigned int irq) |
| 283 | { |
| 284 | void *mapbase = get_irq_chipdata(irq); |
| 285 | unsigned int r; |
| 286 | r = locomo_readl(mapbase + LOCOMO_GWE); |
| 287 | r |= (0x0001 << (irq - LOCOMO_IRQ_GPIO_START)); |
| 288 | locomo_writel(r, mapbase + LOCOMO_GWE); |
| 289 | |
| 290 | r = locomo_readl(mapbase + LOCOMO_GIS); |
| 291 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_GPIO_START)); |
| 292 | locomo_writel(r, mapbase + LOCOMO_GIS); |
| 293 | |
| 294 | r = locomo_readl(mapbase + LOCOMO_GWE); |
| 295 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_GPIO_START)); |
| 296 | locomo_writel(r, mapbase + LOCOMO_GWE); |
| 297 | } |
| 298 | |
| 299 | static void locomo_gpio_mask_irq(unsigned int irq) |
| 300 | { |
| 301 | void *mapbase = get_irq_chipdata(irq); |
| 302 | unsigned int r; |
| 303 | r = locomo_readl(mapbase + LOCOMO_GIE); |
| 304 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_GPIO_START)); |
| 305 | locomo_writel(r, mapbase + LOCOMO_GIE); |
| 306 | } |
| 307 | |
| 308 | static void locomo_gpio_unmask_irq(unsigned int irq) |
| 309 | { |
| 310 | void *mapbase = get_irq_chipdata(irq); |
| 311 | unsigned int r; |
| 312 | r = locomo_readl(mapbase + LOCOMO_GIE); |
| 313 | r |= (0x0001 << (irq - LOCOMO_IRQ_GPIO_START)); |
| 314 | locomo_writel(r, mapbase + LOCOMO_GIE); |
| 315 | } |
| 316 | |
| 317 | static struct irqchip locomo_gpio_chip = { |
| 318 | .ack = locomo_gpio_ack_irq, |
| 319 | .mask = locomo_gpio_mask_irq, |
| 320 | .unmask = locomo_gpio_unmask_irq, |
| 321 | }; |
| 322 | |
| 323 | static void locomo_lt_handler(unsigned int irq, struct irqdesc *desc, |
| 324 | struct pt_regs *regs) |
| 325 | { |
| 326 | struct irqdesc *d; |
| 327 | void *mapbase = get_irq_chipdata(irq); |
| 328 | |
| 329 | if (locomo_readl(mapbase + LOCOMO_LTINT) & 0x0001) { |
| 330 | d = irq_desc + LOCOMO_IRQ_LT_START; |
| 331 | d->handle(LOCOMO_IRQ_LT_START, d, regs); |
| 332 | } |
| 333 | } |
| 334 | |
| 335 | static void locomo_lt_ack_irq(unsigned int irq) |
| 336 | { |
| 337 | void *mapbase = get_irq_chipdata(irq); |
| 338 | unsigned int r; |
| 339 | r = locomo_readl(mapbase + LOCOMO_LTINT); |
| 340 | r &= ~(0x0100 << (irq - LOCOMO_IRQ_LT_START)); |
| 341 | locomo_writel(r, mapbase + LOCOMO_LTINT); |
| 342 | } |
| 343 | |
| 344 | static void locomo_lt_mask_irq(unsigned int irq) |
| 345 | { |
| 346 | void *mapbase = get_irq_chipdata(irq); |
| 347 | unsigned int r; |
| 348 | r = locomo_readl(mapbase + LOCOMO_LTINT); |
| 349 | r &= ~(0x0010 << (irq - LOCOMO_IRQ_LT_START)); |
| 350 | locomo_writel(r, mapbase + LOCOMO_LTINT); |
| 351 | } |
| 352 | |
| 353 | static void locomo_lt_unmask_irq(unsigned int irq) |
| 354 | { |
| 355 | void *mapbase = get_irq_chipdata(irq); |
| 356 | unsigned int r; |
| 357 | r = locomo_readl(mapbase + LOCOMO_LTINT); |
| 358 | r |= (0x0010 << (irq - LOCOMO_IRQ_LT_START)); |
| 359 | locomo_writel(r, mapbase + LOCOMO_LTINT); |
| 360 | } |
| 361 | |
| 362 | static struct irqchip locomo_lt_chip = { |
| 363 | .ack = locomo_lt_ack_irq, |
| 364 | .mask = locomo_lt_mask_irq, |
| 365 | .unmask = locomo_lt_unmask_irq, |
| 366 | }; |
| 367 | |
| 368 | static void locomo_spi_handler(unsigned int irq, struct irqdesc *desc, |
| 369 | struct pt_regs *regs) |
| 370 | { |
| 371 | int req, i; |
| 372 | struct irqdesc *d; |
| 373 | void *mapbase = get_irq_chipdata(irq); |
| 374 | |
| 375 | req = locomo_readl(mapbase + LOCOMO_SPIIR) & 0x000F; |
| 376 | if (req) { |
| 377 | irq = LOCOMO_IRQ_SPI_START; |
| 378 | d = irq_desc + irq; |
| 379 | |
| 380 | for (i = 0; i <= 3; i++, irq++, d++) { |
| 381 | if (req & (0x0001 << i)) { |
| 382 | d->handle(irq, d, regs); |
| 383 | } |
| 384 | } |
| 385 | } |
| 386 | } |
| 387 | |
| 388 | static void locomo_spi_ack_irq(unsigned int irq) |
| 389 | { |
| 390 | void *mapbase = get_irq_chipdata(irq); |
| 391 | unsigned int r; |
| 392 | r = locomo_readl(mapbase + LOCOMO_SPIWE); |
| 393 | r |= (0x0001 << (irq - LOCOMO_IRQ_SPI_START)); |
| 394 | locomo_writel(r, mapbase + LOCOMO_SPIWE); |
| 395 | |
| 396 | r = locomo_readl(mapbase + LOCOMO_SPIIS); |
| 397 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_SPI_START)); |
| 398 | locomo_writel(r, mapbase + LOCOMO_SPIIS); |
| 399 | |
| 400 | r = locomo_readl(mapbase + LOCOMO_SPIWE); |
| 401 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_SPI_START)); |
| 402 | locomo_writel(r, mapbase + LOCOMO_SPIWE); |
| 403 | } |
| 404 | |
| 405 | static void locomo_spi_mask_irq(unsigned int irq) |
| 406 | { |
| 407 | void *mapbase = get_irq_chipdata(irq); |
| 408 | unsigned int r; |
| 409 | r = locomo_readl(mapbase + LOCOMO_SPIIE); |
| 410 | r &= ~(0x0001 << (irq - LOCOMO_IRQ_SPI_START)); |
| 411 | locomo_writel(r, mapbase + LOCOMO_SPIIE); |
| 412 | } |
| 413 | |
| 414 | static void locomo_spi_unmask_irq(unsigned int irq) |
| 415 | { |
| 416 | void *mapbase = get_irq_chipdata(irq); |
| 417 | unsigned int r; |
| 418 | r = locomo_readl(mapbase + LOCOMO_SPIIE); |
| 419 | r |= (0x0001 << (irq - LOCOMO_IRQ_SPI_START)); |
| 420 | locomo_writel(r, mapbase + LOCOMO_SPIIE); |
| 421 | } |
| 422 | |
| 423 | static struct irqchip locomo_spi_chip = { |
| 424 | .ack = locomo_spi_ack_irq, |
| 425 | .mask = locomo_spi_mask_irq, |
| 426 | .unmask = locomo_spi_unmask_irq, |
| 427 | }; |
| 428 | |
| 429 | static void locomo_setup_irq(struct locomo *lchip) |
| 430 | { |
| 431 | int irq; |
| 432 | void *irqbase = lchip->base; |
| 433 | |
| 434 | /* |
| 435 | * Install handler for IRQ_LOCOMO_HW. |
| 436 | */ |
| 437 | set_irq_type(lchip->irq, IRQT_FALLING); |
| 438 | set_irq_chipdata(lchip->irq, irqbase); |
| 439 | set_irq_chained_handler(lchip->irq, locomo_handler); |
| 440 | |
| 441 | /* Install handlers for IRQ_LOCOMO_*_BASE */ |
| 442 | set_irq_chip(IRQ_LOCOMO_KEY_BASE, &locomo_chip); |
| 443 | set_irq_chipdata(IRQ_LOCOMO_KEY_BASE, irqbase); |
| 444 | set_irq_chained_handler(IRQ_LOCOMO_KEY_BASE, locomo_key_handler); |
| 445 | set_irq_flags(IRQ_LOCOMO_KEY_BASE, IRQF_VALID | IRQF_PROBE); |
| 446 | |
| 447 | set_irq_chip(IRQ_LOCOMO_GPIO_BASE, &locomo_chip); |
| 448 | set_irq_chipdata(IRQ_LOCOMO_GPIO_BASE, irqbase); |
| 449 | set_irq_chained_handler(IRQ_LOCOMO_GPIO_BASE, locomo_gpio_handler); |
| 450 | set_irq_flags(IRQ_LOCOMO_GPIO_BASE, IRQF_VALID | IRQF_PROBE); |
| 451 | |
| 452 | set_irq_chip(IRQ_LOCOMO_LT_BASE, &locomo_chip); |
| 453 | set_irq_chipdata(IRQ_LOCOMO_LT_BASE, irqbase); |
| 454 | set_irq_chained_handler(IRQ_LOCOMO_LT_BASE, locomo_lt_handler); |
| 455 | set_irq_flags(IRQ_LOCOMO_LT_BASE, IRQF_VALID | IRQF_PROBE); |
| 456 | |
| 457 | set_irq_chip(IRQ_LOCOMO_SPI_BASE, &locomo_chip); |
| 458 | set_irq_chipdata(IRQ_LOCOMO_SPI_BASE, irqbase); |
| 459 | set_irq_chained_handler(IRQ_LOCOMO_SPI_BASE, locomo_spi_handler); |
| 460 | set_irq_flags(IRQ_LOCOMO_SPI_BASE, IRQF_VALID | IRQF_PROBE); |
| 461 | |
| 462 | /* install handlers for IRQ_LOCOMO_KEY_BASE generated interrupts */ |
| 463 | set_irq_chip(LOCOMO_IRQ_KEY_START, &locomo_key_chip); |
| 464 | set_irq_chipdata(LOCOMO_IRQ_KEY_START, irqbase); |
| 465 | set_irq_handler(LOCOMO_IRQ_KEY_START, do_edge_IRQ); |
| 466 | set_irq_flags(LOCOMO_IRQ_KEY_START, IRQF_VALID | IRQF_PROBE); |
| 467 | |
| 468 | /* install handlers for IRQ_LOCOMO_GPIO_BASE generated interrupts */ |
| 469 | for (irq = LOCOMO_IRQ_GPIO_START; irq < LOCOMO_IRQ_GPIO_START + 16; irq++) { |
| 470 | set_irq_chip(irq, &locomo_gpio_chip); |
| 471 | set_irq_chipdata(irq, irqbase); |
| 472 | set_irq_handler(irq, do_edge_IRQ); |
| 473 | set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); |
| 474 | } |
| 475 | |
| 476 | /* install handlers for IRQ_LOCOMO_LT_BASE generated interrupts */ |
| 477 | set_irq_chip(LOCOMO_IRQ_LT_START, &locomo_lt_chip); |
| 478 | set_irq_chipdata(LOCOMO_IRQ_LT_START, irqbase); |
| 479 | set_irq_handler(LOCOMO_IRQ_LT_START, do_edge_IRQ); |
| 480 | set_irq_flags(LOCOMO_IRQ_LT_START, IRQF_VALID | IRQF_PROBE); |
| 481 | |
| 482 | /* install handlers for IRQ_LOCOMO_SPI_BASE generated interrupts */ |
| 483 | for (irq = LOCOMO_IRQ_SPI_START; irq < LOCOMO_IRQ_SPI_START + 3; irq++) { |
| 484 | set_irq_chip(irq, &locomo_spi_chip); |
| 485 | set_irq_chipdata(irq, irqbase); |
| 486 | set_irq_handler(irq, do_edge_IRQ); |
| 487 | set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); |
| 488 | } |
| 489 | } |
| 490 | |
| 491 | |
| 492 | static void locomo_dev_release(struct device *_dev) |
| 493 | { |
| 494 | struct locomo_dev *dev = LOCOMO_DEV(_dev); |
| 495 | |
| 496 | kfree(dev); |
| 497 | } |
| 498 | |
| 499 | static int |
| 500 | locomo_init_one_child(struct locomo *lchip, struct locomo_dev_info *info) |
| 501 | { |
| 502 | struct locomo_dev *dev; |
| 503 | int ret; |
| 504 | |
| 505 | dev = kmalloc(sizeof(struct locomo_dev), GFP_KERNEL); |
| 506 | if (!dev) { |
| 507 | ret = -ENOMEM; |
| 508 | goto out; |
| 509 | } |
| 510 | memset(dev, 0, sizeof(struct locomo_dev)); |
| 511 | |
| 512 | strncpy(dev->dev.bus_id,info->name,sizeof(dev->dev.bus_id)); |
| 513 | /* |
| 514 | * If the parent device has a DMA mask associated with it, |
| 515 | * propagate it down to the children. |
| 516 | */ |
| 517 | if (lchip->dev->dma_mask) { |
| 518 | dev->dma_mask = *lchip->dev->dma_mask; |
| 519 | dev->dev.dma_mask = &dev->dma_mask; |
| 520 | } |
| 521 | |
| 522 | dev->devid = info->devid; |
| 523 | dev->dev.parent = lchip->dev; |
| 524 | dev->dev.bus = &locomo_bus_type; |
| 525 | dev->dev.release = locomo_dev_release; |
| 526 | dev->dev.coherent_dma_mask = lchip->dev->coherent_dma_mask; |
| 527 | |
| 528 | if (info->offset) |
| 529 | dev->mapbase = lchip->base + info->offset; |
| 530 | else |
| 531 | dev->mapbase = 0; |
| 532 | dev->length = info->length; |
| 533 | |
| 534 | memmove(dev->irq, info->irq, sizeof(dev->irq)); |
| 535 | |
| 536 | ret = device_register(&dev->dev); |
| 537 | if (ret) { |
| 538 | out: |
| 539 | kfree(dev); |
| 540 | } |
| 541 | return ret; |
| 542 | } |
| 543 | |
| 544 | /** |
| 545 | * locomo_probe - probe for a single LoCoMo chip. |
| 546 | * @phys_addr: physical address of device. |
| 547 | * |
| 548 | * Probe for a LoCoMo chip. This must be called |
| 549 | * before any other locomo-specific code. |
| 550 | * |
| 551 | * Returns: |
| 552 | * %-ENODEV device not found. |
| 553 | * %-EBUSY physical address already marked in-use. |
| 554 | * %0 successful. |
| 555 | */ |
| 556 | static int |
| 557 | __locomo_probe(struct device *me, struct resource *mem, int irq) |
| 558 | { |
| 559 | struct locomo *lchip; |
| 560 | unsigned long r; |
| 561 | int i, ret = -ENODEV; |
| 562 | |
| 563 | lchip = kmalloc(sizeof(struct locomo), GFP_KERNEL); |
| 564 | if (!lchip) |
| 565 | return -ENOMEM; |
| 566 | |
| 567 | memset(lchip, 0, sizeof(struct locomo)); |
| 568 | |
| 569 | spin_lock_init(&lchip->lock); |
| 570 | |
| 571 | lchip->dev = me; |
| 572 | dev_set_drvdata(lchip->dev, lchip); |
| 573 | |
| 574 | lchip->phys = mem->start; |
| 575 | lchip->irq = irq; |
| 576 | |
| 577 | /* |
| 578 | * Map the whole region. This also maps the |
| 579 | * registers for our children. |
| 580 | */ |
| 581 | lchip->base = ioremap(mem->start, PAGE_SIZE); |
| 582 | if (!lchip->base) { |
| 583 | ret = -ENOMEM; |
| 584 | goto out; |
| 585 | } |
| 586 | |
| 587 | /* locomo initialize */ |
| 588 | locomo_writel(0, lchip->base + LOCOMO_ICR); |
| 589 | /* KEYBOARD */ |
| 590 | locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); |
| 591 | |
| 592 | /* GPIO */ |
| 593 | locomo_writel(0, lchip->base + LOCOMO_GPO); |
| 594 | locomo_writel( (LOCOMO_GPIO(2) | LOCOMO_GPIO(3) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) |
| 595 | , lchip->base + LOCOMO_GPE); |
| 596 | locomo_writel( (LOCOMO_GPIO(2) | LOCOMO_GPIO(3) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) |
| 597 | , lchip->base + LOCOMO_GPD); |
| 598 | locomo_writel(0, lchip->base + LOCOMO_GIE); |
| 599 | |
| 600 | /* FrontLight */ |
| 601 | locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); |
| 602 | locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD); |
| 603 | /* Longtime timer */ |
| 604 | locomo_writel(0, lchip->base + LOCOMO_LTINT); |
| 605 | /* SPI */ |
| 606 | locomo_writel(0, lchip->base + LOCOMO_SPIIE); |
| 607 | |
| 608 | locomo_writel(6 + 8 + 320 + 30 - 10, lchip->base + LOCOMO_ASD); |
| 609 | r = locomo_readl(lchip->base + LOCOMO_ASD); |
| 610 | r |= 0x8000; |
| 611 | locomo_writel(r, lchip->base + LOCOMO_ASD); |
| 612 | |
| 613 | locomo_writel(6 + 8 + 320 + 30 - 10 - 128 + 4, lchip->base + LOCOMO_HSD); |
| 614 | r = locomo_readl(lchip->base + LOCOMO_HSD); |
| 615 | r |= 0x8000; |
| 616 | locomo_writel(r, lchip->base + LOCOMO_HSD); |
| 617 | |
| 618 | locomo_writel(128 / 8, lchip->base + LOCOMO_HSC); |
| 619 | |
| 620 | /* XON */ |
| 621 | locomo_writel(0x80, lchip->base + LOCOMO_TADC); |
| 622 | udelay(1000); |
| 623 | /* CLK9MEN */ |
| 624 | r = locomo_readl(lchip->base + LOCOMO_TADC); |
| 625 | r |= 0x10; |
| 626 | locomo_writel(r, lchip->base + LOCOMO_TADC); |
| 627 | udelay(100); |
| 628 | |
| 629 | /* init DAC */ |
| 630 | r = locomo_readl(lchip->base + LOCOMO_DAC); |
| 631 | r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; |
| 632 | locomo_writel(r, lchip->base + LOCOMO_DAC); |
| 633 | |
| 634 | r = locomo_readl(lchip->base + LOCOMO_VER); |
| 635 | printk(KERN_INFO "LoCoMo Chip: %lu%lu\n", (r >> 8), (r & 0xff)); |
| 636 | |
| 637 | /* |
| 638 | * The interrupt controller must be initialised before any |
| 639 | * other device to ensure that the interrupts are available. |
| 640 | */ |
| 641 | if (lchip->irq != NO_IRQ) |
| 642 | locomo_setup_irq(lchip); |
| 643 | |
| 644 | for (i = 0; i < ARRAY_SIZE(locomo_devices); i++) |
| 645 | locomo_init_one_child(lchip, &locomo_devices[i]); |
| 646 | |
| 647 | return 0; |
| 648 | |
| 649 | out: |
| 650 | kfree(lchip); |
| 651 | return ret; |
| 652 | } |
| 653 | |
Pavel Machek | e24da5d | 2005-09-04 11:33:12 +0100 | [diff] [blame^] | 654 | static int locomo_remove_child(struct device *dev, void *data) |
| 655 | { |
| 656 | device_unregister(dev); |
| 657 | return 0; |
| 658 | } |
| 659 | |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 660 | static void __locomo_remove(struct locomo *lchip) |
| 661 | { |
Pavel Machek | e24da5d | 2005-09-04 11:33:12 +0100 | [diff] [blame^] | 662 | device_for_each_child(lchip->dev, NULL, locomo_remove_child); |
Linus Torvalds | 1da177e | 2005-04-16 15:20:36 -0700 | [diff] [blame] | 663 | |
| 664 | if (lchip->irq != NO_IRQ) { |
| 665 | set_irq_chained_handler(lchip->irq, NULL); |
| 666 | set_irq_data(lchip->irq, NULL); |
| 667 | } |
| 668 | |
| 669 | iounmap(lchip->base); |
| 670 | kfree(lchip); |
| 671 | } |
| 672 | |
| 673 | static int locomo_probe(struct device *dev) |
| 674 | { |
| 675 | struct platform_device *pdev = to_platform_device(dev); |
| 676 | struct resource *mem; |
| 677 | int irq; |
| 678 | |
| 679 | mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| 680 | if (!mem) |
| 681 | return -EINVAL; |
| 682 | irq = platform_get_irq(pdev, 0); |
| 683 | |
| 684 | return __locomo_probe(dev, mem, irq); |
| 685 | } |
| 686 | |
| 687 | static int locomo_remove(struct device *dev) |
| 688 | { |
| 689 | struct locomo *lchip = dev_get_drvdata(dev); |
| 690 | |
| 691 | if (lchip) { |
| 692 | __locomo_remove(lchip); |
| 693 | dev_set_drvdata(dev, NULL); |
| 694 | } |
| 695 | |
| 696 | return 0; |
| 697 | } |
| 698 | |
| 699 | /* |
| 700 | * Not sure if this should be on the system bus or not yet. |
| 701 | * We really want some way to register a system device at |
| 702 | * the per-machine level, and then have this driver pick |
| 703 | * up the registered devices. |
| 704 | */ |
| 705 | static struct device_driver locomo_device_driver = { |
| 706 | .name = "locomo", |
| 707 | .bus = &platform_bus_type, |
| 708 | .probe = locomo_probe, |
| 709 | .remove = locomo_remove, |
| 710 | }; |
| 711 | |
| 712 | /* |
| 713 | * Get the parent device driver (us) structure |
| 714 | * from a child function device |
| 715 | */ |
| 716 | static inline struct locomo *locomo_chip_driver(struct locomo_dev *ldev) |
| 717 | { |
| 718 | return (struct locomo *)dev_get_drvdata(ldev->dev.parent); |
| 719 | } |
| 720 | |
| 721 | void locomo_gpio_set_dir(struct locomo_dev *ldev, unsigned int bits, unsigned int dir) |
| 722 | { |
| 723 | struct locomo *lchip = locomo_chip_driver(ldev); |
| 724 | unsigned long flags; |
| 725 | unsigned int r; |
| 726 | |
| 727 | spin_lock_irqsave(&lchip->lock, flags); |
| 728 | |
| 729 | r = locomo_readl(lchip->base + LOCOMO_GPD); |
| 730 | r &= ~bits; |
| 731 | locomo_writel(r, lchip->base + LOCOMO_GPD); |
| 732 | |
| 733 | r = locomo_readl(lchip->base + LOCOMO_GPE); |
| 734 | if (dir) |
| 735 | r |= bits; |
| 736 | else |
| 737 | r &= ~bits; |
| 738 | locomo_writel(r, lchip->base + LOCOMO_GPE); |
| 739 | |
| 740 | spin_unlock_irqrestore(&lchip->lock, flags); |
| 741 | } |
| 742 | |
| 743 | unsigned int locomo_gpio_read_level(struct locomo_dev *ldev, unsigned int bits) |
| 744 | { |
| 745 | struct locomo *lchip = locomo_chip_driver(ldev); |
| 746 | unsigned long flags; |
| 747 | unsigned int ret; |
| 748 | |
| 749 | spin_lock_irqsave(&lchip->lock, flags); |
| 750 | ret = locomo_readl(lchip->base + LOCOMO_GPL); |
| 751 | spin_unlock_irqrestore(&lchip->lock, flags); |
| 752 | |
| 753 | ret &= bits; |
| 754 | return ret; |
| 755 | } |
| 756 | |
| 757 | unsigned int locomo_gpio_read_output(struct locomo_dev *ldev, unsigned int bits) |
| 758 | { |
| 759 | struct locomo *lchip = locomo_chip_driver(ldev); |
| 760 | unsigned long flags; |
| 761 | unsigned int ret; |
| 762 | |
| 763 | spin_lock_irqsave(&lchip->lock, flags); |
| 764 | ret = locomo_readl(lchip->base + LOCOMO_GPO); |
| 765 | spin_unlock_irqrestore(&lchip->lock, flags); |
| 766 | |
| 767 | ret &= bits; |
| 768 | return ret; |
| 769 | } |
| 770 | |
| 771 | void locomo_gpio_write(struct locomo_dev *ldev, unsigned int bits, unsigned int set) |
| 772 | { |
| 773 | struct locomo *lchip = locomo_chip_driver(ldev); |
| 774 | unsigned long flags; |
| 775 | unsigned int r; |
| 776 | |
| 777 | spin_lock_irqsave(&lchip->lock, flags); |
| 778 | |
| 779 | r = locomo_readl(lchip->base + LOCOMO_GPO); |
| 780 | if (set) |
| 781 | r |= bits; |
| 782 | else |
| 783 | r &= ~bits; |
| 784 | locomo_writel(r, lchip->base + LOCOMO_GPO); |
| 785 | |
| 786 | spin_unlock_irqrestore(&lchip->lock, flags); |
| 787 | } |
| 788 | |
| 789 | static void locomo_m62332_sendbit(void *mapbase, int bit) |
| 790 | { |
| 791 | unsigned int r; |
| 792 | |
| 793 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 794 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 795 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 796 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 797 | udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ |
| 798 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 799 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 800 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 801 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 802 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 803 | |
| 804 | if (bit & 1) { |
| 805 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 806 | r |= LOCOMO_DAC_SDAOEB; |
| 807 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 808 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 809 | } else { |
| 810 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 811 | r &= ~(LOCOMO_DAC_SDAOEB); |
| 812 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 813 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 814 | } |
| 815 | |
| 816 | udelay(DAC_DATA_SETUP_TIME); /* 250 nsec */ |
| 817 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 818 | r |= LOCOMO_DAC_SCLOEB; |
| 819 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 820 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 821 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ |
| 822 | } |
| 823 | |
| 824 | void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel) |
| 825 | { |
| 826 | struct locomo *lchip = locomo_chip_driver(ldev); |
| 827 | int i; |
| 828 | unsigned char data; |
| 829 | unsigned int r; |
| 830 | void *mapbase = lchip->base; |
| 831 | unsigned long flags; |
| 832 | |
| 833 | spin_lock_irqsave(&lchip->lock, flags); |
| 834 | |
| 835 | /* Start */ |
| 836 | udelay(DAC_BUS_FREE_TIME); /* 5.0 usec */ |
| 837 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 838 | r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; |
| 839 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 840 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 841 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ |
| 842 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 843 | r &= ~(LOCOMO_DAC_SDAOEB); |
| 844 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 845 | udelay(DAC_START_HOLD_TIME); /* 5.0 usec */ |
| 846 | udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ |
| 847 | |
| 848 | /* Send slave address and W bit (LSB is W bit) */ |
| 849 | data = (M62332_SLAVE_ADDR << 1) | M62332_W_BIT; |
| 850 | for (i = 1; i <= 8; i++) { |
| 851 | locomo_m62332_sendbit(mapbase, data >> (8 - i)); |
| 852 | } |
| 853 | |
| 854 | /* Check A bit */ |
| 855 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 856 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 857 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 858 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 859 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 860 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 861 | r &= ~(LOCOMO_DAC_SDAOEB); |
| 862 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 863 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 864 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 865 | r |= LOCOMO_DAC_SCLOEB; |
| 866 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 867 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 868 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ |
| 869 | if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ |
| 870 | printk(KERN_WARNING "locomo: m62332_senddata Error 1\n"); |
| 871 | return; |
| 872 | } |
| 873 | |
| 874 | /* Send Sub address (LSB is channel select) */ |
| 875 | /* channel = 0 : ch1 select */ |
| 876 | /* = 1 : ch2 select */ |
| 877 | data = M62332_SUB_ADDR + channel; |
| 878 | for (i = 1; i <= 8; i++) { |
| 879 | locomo_m62332_sendbit(mapbase, data >> (8 - i)); |
| 880 | } |
| 881 | |
| 882 | /* Check A bit */ |
| 883 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 884 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 885 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 886 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 887 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 888 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 889 | r &= ~(LOCOMO_DAC_SDAOEB); |
| 890 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 891 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 892 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 893 | r |= LOCOMO_DAC_SCLOEB; |
| 894 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 895 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 896 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ |
| 897 | if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ |
| 898 | printk(KERN_WARNING "locomo: m62332_senddata Error 2\n"); |
| 899 | return; |
| 900 | } |
| 901 | |
| 902 | /* Send DAC data */ |
| 903 | for (i = 1; i <= 8; i++) { |
| 904 | locomo_m62332_sendbit(mapbase, dac_data >> (8 - i)); |
| 905 | } |
| 906 | |
| 907 | /* Check A bit */ |
| 908 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 909 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 910 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 911 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 912 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 913 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 914 | r &= ~(LOCOMO_DAC_SDAOEB); |
| 915 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 916 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 917 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 918 | r |= LOCOMO_DAC_SCLOEB; |
| 919 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 920 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 921 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ |
| 922 | if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ |
| 923 | printk(KERN_WARNING "locomo: m62332_senddata Error 3\n"); |
| 924 | return; |
| 925 | } |
| 926 | |
| 927 | /* stop */ |
| 928 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 929 | r &= ~(LOCOMO_DAC_SCLOEB); |
| 930 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 931 | udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ |
| 932 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 933 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 934 | r |= LOCOMO_DAC_SCLOEB; |
| 935 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 936 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 937 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ |
| 938 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 939 | r |= LOCOMO_DAC_SDAOEB; |
| 940 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 941 | udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ |
| 942 | udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ |
| 943 | |
| 944 | r = locomo_readl(mapbase + LOCOMO_DAC); |
| 945 | r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; |
| 946 | locomo_writel(r, mapbase + LOCOMO_DAC); |
| 947 | udelay(DAC_LOW_SETUP_TIME); /* 1000 nsec */ |
| 948 | udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ |
| 949 | |
| 950 | spin_unlock_irqrestore(&lchip->lock, flags); |
| 951 | } |
| 952 | |
| 953 | /* |
| 954 | * LoCoMo "Register Access Bus." |
| 955 | * |
| 956 | * We model this as a regular bus type, and hang devices directly |
| 957 | * off this. |
| 958 | */ |
| 959 | static int locomo_match(struct device *_dev, struct device_driver *_drv) |
| 960 | { |
| 961 | struct locomo_dev *dev = LOCOMO_DEV(_dev); |
| 962 | struct locomo_driver *drv = LOCOMO_DRV(_drv); |
| 963 | |
| 964 | return dev->devid == drv->devid; |
| 965 | } |
| 966 | |
| 967 | static int locomo_bus_suspend(struct device *dev, pm_message_t state) |
| 968 | { |
| 969 | struct locomo_dev *ldev = LOCOMO_DEV(dev); |
| 970 | struct locomo_driver *drv = LOCOMO_DRV(dev->driver); |
| 971 | int ret = 0; |
| 972 | |
| 973 | if (drv && drv->suspend) |
| 974 | ret = drv->suspend(ldev, state); |
| 975 | return ret; |
| 976 | } |
| 977 | |
| 978 | static int locomo_bus_resume(struct device *dev) |
| 979 | { |
| 980 | struct locomo_dev *ldev = LOCOMO_DEV(dev); |
| 981 | struct locomo_driver *drv = LOCOMO_DRV(dev->driver); |
| 982 | int ret = 0; |
| 983 | |
| 984 | if (drv && drv->resume) |
| 985 | ret = drv->resume(ldev); |
| 986 | return ret; |
| 987 | } |
| 988 | |
| 989 | static int locomo_bus_probe(struct device *dev) |
| 990 | { |
| 991 | struct locomo_dev *ldev = LOCOMO_DEV(dev); |
| 992 | struct locomo_driver *drv = LOCOMO_DRV(dev->driver); |
| 993 | int ret = -ENODEV; |
| 994 | |
| 995 | if (drv->probe) |
| 996 | ret = drv->probe(ldev); |
| 997 | return ret; |
| 998 | } |
| 999 | |
| 1000 | static int locomo_bus_remove(struct device *dev) |
| 1001 | { |
| 1002 | struct locomo_dev *ldev = LOCOMO_DEV(dev); |
| 1003 | struct locomo_driver *drv = LOCOMO_DRV(dev->driver); |
| 1004 | int ret = 0; |
| 1005 | |
| 1006 | if (drv->remove) |
| 1007 | ret = drv->remove(ldev); |
| 1008 | return ret; |
| 1009 | } |
| 1010 | |
| 1011 | struct bus_type locomo_bus_type = { |
| 1012 | .name = "locomo-bus", |
| 1013 | .match = locomo_match, |
| 1014 | .suspend = locomo_bus_suspend, |
| 1015 | .resume = locomo_bus_resume, |
| 1016 | }; |
| 1017 | |
| 1018 | int locomo_driver_register(struct locomo_driver *driver) |
| 1019 | { |
| 1020 | driver->drv.probe = locomo_bus_probe; |
| 1021 | driver->drv.remove = locomo_bus_remove; |
| 1022 | driver->drv.bus = &locomo_bus_type; |
| 1023 | return driver_register(&driver->drv); |
| 1024 | } |
| 1025 | |
| 1026 | void locomo_driver_unregister(struct locomo_driver *driver) |
| 1027 | { |
| 1028 | driver_unregister(&driver->drv); |
| 1029 | } |
| 1030 | |
| 1031 | static int __init locomo_init(void) |
| 1032 | { |
| 1033 | int ret = bus_register(&locomo_bus_type); |
| 1034 | if (ret == 0) |
| 1035 | driver_register(&locomo_device_driver); |
| 1036 | return ret; |
| 1037 | } |
| 1038 | |
| 1039 | static void __exit locomo_exit(void) |
| 1040 | { |
| 1041 | driver_unregister(&locomo_device_driver); |
| 1042 | bus_unregister(&locomo_bus_type); |
| 1043 | } |
| 1044 | |
| 1045 | module_init(locomo_init); |
| 1046 | module_exit(locomo_exit); |
| 1047 | |
| 1048 | MODULE_DESCRIPTION("Sharp LoCoMo core driver"); |
| 1049 | MODULE_LICENSE("GPL"); |
| 1050 | MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>"); |
| 1051 | |
| 1052 | EXPORT_SYMBOL(locomo_driver_register); |
| 1053 | EXPORT_SYMBOL(locomo_driver_unregister); |
| 1054 | EXPORT_SYMBOL(locomo_gpio_set_dir); |
| 1055 | EXPORT_SYMBOL(locomo_gpio_read_level); |
| 1056 | EXPORT_SYMBOL(locomo_gpio_read_output); |
| 1057 | EXPORT_SYMBOL(locomo_gpio_write); |
| 1058 | EXPORT_SYMBOL(locomo_m62332_senddata); |