blob: ddd2688e7d33ee61e76c9fad7e7796a5273ef825 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*------------------------------------------------------------------------
2 . smc91x.h - macros for SMSC's 91C9x/91C1xx single-chip Ethernet device.
3 .
4 . Copyright (C) 1996 by Erik Stahlman
5 . Copyright (C) 2001 Standard Microsystems Corporation
6 . Developed by Simple Network Magic Corporation
7 . Copyright (C) 2003 Monta Vista Software, Inc.
8 . Unified SMC91x driver by Nicolas Pitre
9 .
10 . This program is free software; you can redistribute it and/or modify
11 . it under the terms of the GNU General Public License as published by
12 . the Free Software Foundation; either version 2 of the License, or
13 . (at your option) any later version.
14 .
15 . This program is distributed in the hope that it will be useful,
16 . but WITHOUT ANY WARRANTY; without even the implied warranty of
17 . MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 . GNU General Public License for more details.
19 .
20 . You should have received a copy of the GNU General Public License
21 . along with this program; if not, write to the Free Software
22 . Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 .
24 . Information contained in this file was obtained from the LAN91C111
25 . manual from SMC. To get a copy, if you really want one, you can find
26 . information under www.smsc.com.
27 .
28 . Authors
29 . Erik Stahlman <erik@vt.edu>
30 . Daris A Nevil <dnevil@snmc.com>
31 . Nicolas Pitre <nico@cam.org>
32 .
33 ---------------------------------------------------------------------------*/
34#ifndef _SMC91X_H_
35#define _SMC91X_H_
36
37
38/*
39 * Define your architecture specific bus configuration parameters here.
40 */
41
42#if defined(CONFIG_ARCH_LUBBOCK)
43
44/* We can only do 16-bit reads and writes in the static memory space. */
45#define SMC_CAN_USE_8BIT 0
46#define SMC_CAN_USE_16BIT 1
47#define SMC_CAN_USE_32BIT 0
48#define SMC_NOWAIT 1
49
50/* The first two address lines aren't connected... */
51#define SMC_IO_SHIFT 2
52
53#define SMC_inw(a, r) readw((a) + (r))
54#define SMC_outw(v, a, r) writew(v, (a) + (r))
55#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
56#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
57
58#elif defined(CONFIG_REDWOOD_5) || defined(CONFIG_REDWOOD_6)
59
60/* We can only do 16-bit reads and writes in the static memory space. */
61#define SMC_CAN_USE_8BIT 0
62#define SMC_CAN_USE_16BIT 1
63#define SMC_CAN_USE_32BIT 0
64#define SMC_NOWAIT 1
65
66#define SMC_IO_SHIFT 0
67
68#define SMC_inw(a, r) in_be16((volatile u16 *)((a) + (r)))
69#define SMC_outw(v, a, r) out_be16((volatile u16 *)((a) + (r)), v)
70#define SMC_insw(a, r, p, l) \
71 do { \
72 unsigned long __port = (a) + (r); \
73 u16 *__p = (u16 *)(p); \
74 int __l = (l); \
75 insw(__port, __p, __l); \
76 while (__l > 0) { \
77 *__p = swab16(*__p); \
78 __p++; \
79 __l--; \
80 } \
81 } while (0)
82#define SMC_outsw(a, r, p, l) \
83 do { \
84 unsigned long __port = (a) + (r); \
85 u16 *__p = (u16 *)(p); \
86 int __l = (l); \
87 while (__l > 0) { \
88 /* Believe it or not, the swab isn't needed. */ \
89 outw( /* swab16 */ (*__p++), __port); \
90 __l--; \
91 } \
92 } while (0)
93#define set_irq_type(irq, type)
94
95#elif defined(CONFIG_SA1100_PLEB)
96/* We can only do 16-bit reads and writes in the static memory space. */
97#define SMC_CAN_USE_8BIT 1
98#define SMC_CAN_USE_16BIT 1
99#define SMC_CAN_USE_32BIT 0
100#define SMC_IO_SHIFT 0
101#define SMC_NOWAIT 1
102
103#define SMC_inb(a, r) inb((a) + (r))
104#define SMC_insb(a, r, p, l) insb((a) + (r), p, (l))
105#define SMC_inw(a, r) inw((a) + (r))
106#define SMC_insw(a, r, p, l) insw((a) + (r), p, l)
107#define SMC_outb(v, a, r) outb(v, (a) + (r))
108#define SMC_outsb(a, r, p, l) outsb((a) + (r), p, (l))
109#define SMC_outw(v, a, r) outw(v, (a) + (r))
110#define SMC_outsw(a, r, p, l) outsw((a) + (r), p, l)
111
112#define set_irq_type(irq, type) do {} while (0)
113
114#elif defined(CONFIG_SA1100_ASSABET)
115
116#include <asm/arch/neponset.h>
117
118/* We can only do 8-bit reads and writes in the static memory space. */
119#define SMC_CAN_USE_8BIT 1
120#define SMC_CAN_USE_16BIT 0
121#define SMC_CAN_USE_32BIT 0
122#define SMC_NOWAIT 1
123
124/* The first two address lines aren't connected... */
125#define SMC_IO_SHIFT 2
126
127#define SMC_inb(a, r) readb((a) + (r))
128#define SMC_outb(v, a, r) writeb(v, (a) + (r))
129#define SMC_insb(a, r, p, l) readsb((a) + (r), p, (l))
130#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, (l))
131
132#elif defined(CONFIG_ARCH_INNOKOM) || \
133 defined(CONFIG_MACH_MAINSTONE) || \
134 defined(CONFIG_ARCH_PXA_IDP) || \
135 defined(CONFIG_ARCH_RAMSES)
136
137#define SMC_CAN_USE_8BIT 1
138#define SMC_CAN_USE_16BIT 1
139#define SMC_CAN_USE_32BIT 1
140#define SMC_IO_SHIFT 0
141#define SMC_NOWAIT 1
142#define SMC_USE_PXA_DMA 1
143
144#define SMC_inb(a, r) readb((a) + (r))
145#define SMC_inw(a, r) readw((a) + (r))
146#define SMC_inl(a, r) readl((a) + (r))
147#define SMC_outb(v, a, r) writeb(v, (a) + (r))
148#define SMC_outl(v, a, r) writel(v, (a) + (r))
149#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
150#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
151
152/* We actually can't write halfwords properly if not word aligned */
153static inline void
154SMC_outw(u16 val, unsigned long ioaddr, int reg)
155{
156 if (reg & 2) {
157 unsigned int v = val << 16;
158 v |= readl(ioaddr + (reg & ~2)) & 0xffff;
159 writel(v, ioaddr + (reg & ~2));
160 } else {
161 writew(val, ioaddr + reg);
162 }
163}
164
165#elif defined(CONFIG_ARCH_OMAP)
166
167/* We can only do 16-bit reads and writes in the static memory space. */
168#define SMC_CAN_USE_8BIT 0
169#define SMC_CAN_USE_16BIT 1
170#define SMC_CAN_USE_32BIT 0
171#define SMC_IO_SHIFT 0
172#define SMC_NOWAIT 1
173
174#define SMC_inb(a, r) readb((a) + (r))
175#define SMC_outb(v, a, r) writeb(v, (a) + (r))
176#define SMC_inw(a, r) readw((a) + (r))
177#define SMC_outw(v, a, r) writew(v, (a) + (r))
178#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l)
179#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l)
180#define SMC_inl(a, r) readl((a) + (r))
181#define SMC_outl(v, a, r) writel(v, (a) + (r))
182#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
183#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
184
185#elif defined(CONFIG_SH_SH4202_MICRODEV)
186
187#define SMC_CAN_USE_8BIT 0
188#define SMC_CAN_USE_16BIT 1
189#define SMC_CAN_USE_32BIT 0
190
191#define SMC_inb(a, r) inb((a) + (r) - 0xa0000000)
192#define SMC_inw(a, r) inw((a) + (r) - 0xa0000000)
193#define SMC_inl(a, r) inl((a) + (r) - 0xa0000000)
194#define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000)
195#define SMC_outw(v, a, r) outw(v, (a) + (r) - 0xa0000000)
196#define SMC_outl(v, a, r) outl(v, (a) + (r) - 0xa0000000)
197#define SMC_insl(a, r, p, l) insl((a) + (r) - 0xa0000000, p, l)
198#define SMC_outsl(a, r, p, l) outsl((a) + (r) - 0xa0000000, p, l)
199#define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l)
200#define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l)
201
202#define set_irq_type(irq, type) do {} while(0)
203
204#elif defined(CONFIG_ISA)
205
206#define SMC_CAN_USE_8BIT 1
207#define SMC_CAN_USE_16BIT 1
208#define SMC_CAN_USE_32BIT 0
209
210#define SMC_inb(a, r) inb((a) + (r))
211#define SMC_inw(a, r) inw((a) + (r))
212#define SMC_outb(v, a, r) outb(v, (a) + (r))
213#define SMC_outw(v, a, r) outw(v, (a) + (r))
214#define SMC_insw(a, r, p, l) insw((a) + (r), p, l)
215#define SMC_outsw(a, r, p, l) outsw((a) + (r), p, l)
216
217#elif defined(CONFIG_M32R)
218
219#define SMC_CAN_USE_8BIT 0
220#define SMC_CAN_USE_16BIT 1
221#define SMC_CAN_USE_32BIT 0
222
223#define SMC_inb(a, r) inb((a) + (r) - 0xa0000000)
224#define SMC_inw(a, r) inw((a) + (r) - 0xa0000000)
225#define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000)
226#define SMC_outw(v, a, r) outw(v, (a) + (r) - 0xa0000000)
227#define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l)
228#define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l)
229
230#define set_irq_type(irq, type) do {} while(0)
231
232#define RPC_LSA_DEFAULT RPC_LED_TX_RX
233#define RPC_LSB_DEFAULT RPC_LED_100_10
234
235#elif defined(CONFIG_MACH_LPD7A400) || defined(CONFIG_MACH_LPD7A404)
236
237/* The LPD7A40X_IOBARRIER is necessary to overcome a mismatch between
238 * the way that the CPU handles chip selects and the way that the SMC
239 * chip expects the chip select to operate. Refer to
240 * Documentation/arm/Sharp-LH/IOBarrier for details. The read from
241 * IOBARRIER is a byte as a least-common denominator of possible
242 * regions to use as the barrier. It would be wasteful to read 32
243 * bits from a byte oriented region.
244 *
245 * There is no explicit protection against interrupts intervening
246 * between the writew and the IOBARRIER. In SMC ISR there is a
247 * preamble that performs an IOBARRIER in the extremely unlikely event
248 * that the driver interrupts itself between a writew to the chip an
249 * the IOBARRIER that follows *and* the cache is large enough that the
250 * first off-chip access while handing the interrupt is to the SMC
251 * chip. Other devices in the same address space as the SMC chip must
252 * be aware of the potential for trouble and perform a similar
253 * IOBARRIER on entry to their ISR.
254 */
255
256#include <asm/arch/constants.h> /* IOBARRIER_VIRT */
257
258#define SMC_CAN_USE_8BIT 0
259#define SMC_CAN_USE_16BIT 1
260#define SMC_CAN_USE_32BIT 0
261#define SMC_NOWAIT 0
262#define LPD7A40X_IOBARRIER readb (IOBARRIER_VIRT)
263
264#define SMC_inw(a,r) readw ((void*) ((a) + (r)))
265#define SMC_insw(a,r,p,l) readsw ((void*) ((a) + (r)), p, l)
266#define SMC_outw(v,a,r) ({ writew ((v), (a) + (r)); LPD7A40X_IOBARRIER; })
267
268static inline void SMC_outsw (unsigned long a, int r, unsigned char* p, int l)
269{
270 unsigned short* ps = (unsigned short*) p;
271 while (l-- > 0) {
272 writew (*ps++, a + r);
273 LPD7A40X_IOBARRIER;
274 }
275}
276
277#define SMC_INTERRUPT_PREAMBLE LPD7A40X_IOBARRIER
278
279#define RPC_LSA_DEFAULT RPC_LED_TX_RX
280#define RPC_LSB_DEFAULT RPC_LED_100_10
281
282#else
283
284#define SMC_CAN_USE_8BIT 1
285#define SMC_CAN_USE_16BIT 1
286#define SMC_CAN_USE_32BIT 1
287#define SMC_NOWAIT 1
288
289#define SMC_inb(a, r) readb((a) + (r))
290#define SMC_inw(a, r) readw((a) + (r))
291#define SMC_inl(a, r) readl((a) + (r))
292#define SMC_outb(v, a, r) writeb(v, (a) + (r))
293#define SMC_outw(v, a, r) writew(v, (a) + (r))
294#define SMC_outl(v, a, r) writel(v, (a) + (r))
295#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l)
296#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l)
297
298#define RPC_LSA_DEFAULT RPC_LED_100_10
299#define RPC_LSB_DEFAULT RPC_LED_TX_RX
300
301#endif
302
303
304#ifdef SMC_USE_PXA_DMA
305/*
306 * Let's use the DMA engine on the XScale PXA2xx for RX packets. This is
307 * always happening in irq context so no need to worry about races. TX is
308 * different and probably not worth it for that reason, and not as critical
309 * as RX which can overrun memory and lose packets.
310 */
311#include <linux/dma-mapping.h>
312#include <asm/dma.h>
313#include <asm/arch/pxa-regs.h>
314
315#ifdef SMC_insl
316#undef SMC_insl
317#define SMC_insl(a, r, p, l) \
318 smc_pxa_dma_insl(a, lp->physaddr, r, dev->dma, p, l)
319static inline void
320smc_pxa_dma_insl(u_long ioaddr, u_long physaddr, int reg, int dma,
321 u_char *buf, int len)
322{
323 dma_addr_t dmabuf;
324
325 /* fallback if no DMA available */
326 if (dma == (unsigned char)-1) {
327 readsl(ioaddr + reg, buf, len);
328 return;
329 }
330
331 /* 64 bit alignment is required for memory to memory DMA */
332 if ((long)buf & 4) {
333 *((u32 *)buf) = SMC_inl(ioaddr, reg);
334 buf += 4;
335 len--;
336 }
337
338 len *= 4;
339 dmabuf = dma_map_single(NULL, buf, len, DMA_FROM_DEVICE);
340 DCSR(dma) = DCSR_NODESC;
341 DTADR(dma) = dmabuf;
342 DSADR(dma) = physaddr + reg;
343 DCMD(dma) = (DCMD_INCTRGADDR | DCMD_BURST32 |
344 DCMD_WIDTH4 | (DCMD_LENGTH & len));
345 DCSR(dma) = DCSR_NODESC | DCSR_RUN;
346 while (!(DCSR(dma) & DCSR_STOPSTATE))
347 cpu_relax();
348 DCSR(dma) = 0;
349 dma_unmap_single(NULL, dmabuf, len, DMA_FROM_DEVICE);
350}
351#endif
352
353#ifdef SMC_insw
354#undef SMC_insw
355#define SMC_insw(a, r, p, l) \
356 smc_pxa_dma_insw(a, lp->physaddr, r, dev->dma, p, l)
357static inline void
358smc_pxa_dma_insw(u_long ioaddr, u_long physaddr, int reg, int dma,
359 u_char *buf, int len)
360{
361 dma_addr_t dmabuf;
362
363 /* fallback if no DMA available */
364 if (dma == (unsigned char)-1) {
365 readsw(ioaddr + reg, buf, len);
366 return;
367 }
368
369 /* 64 bit alignment is required for memory to memory DMA */
370 while ((long)buf & 6) {
371 *((u16 *)buf) = SMC_inw(ioaddr, reg);
372 buf += 2;
373 len--;
374 }
375
376 len *= 2;
377 dmabuf = dma_map_single(NULL, buf, len, DMA_FROM_DEVICE);
378 DCSR(dma) = DCSR_NODESC;
379 DTADR(dma) = dmabuf;
380 DSADR(dma) = physaddr + reg;
381 DCMD(dma) = (DCMD_INCTRGADDR | DCMD_BURST32 |
382 DCMD_WIDTH2 | (DCMD_LENGTH & len));
383 DCSR(dma) = DCSR_NODESC | DCSR_RUN;
384 while (!(DCSR(dma) & DCSR_STOPSTATE))
385 cpu_relax();
386 DCSR(dma) = 0;
387 dma_unmap_single(NULL, dmabuf, len, DMA_FROM_DEVICE);
388}
389#endif
390
391static void
392smc_pxa_dma_irq(int dma, void *dummy, struct pt_regs *regs)
393{
394 DCSR(dma) = 0;
395}
396#endif /* SMC_USE_PXA_DMA */
397
398
399/* Because of bank switching, the LAN91x uses only 16 I/O ports */
400#ifndef SMC_IO_SHIFT
401#define SMC_IO_SHIFT 0
402#endif
403#define SMC_IO_EXTENT (16 << SMC_IO_SHIFT)
404#define SMC_DATA_EXTENT (4)
405
406/*
407 . Bank Select Register:
408 .
409 . yyyy yyyy 0000 00xx
410 . xx = bank number
411 . yyyy yyyy = 0x33, for identification purposes.
412*/
413#define BANK_SELECT (14 << SMC_IO_SHIFT)
414
415
416// Transmit Control Register
417/* BANK 0 */
418#define TCR_REG SMC_REG(0x0000, 0)
419#define TCR_ENABLE 0x0001 // When 1 we can transmit
420#define TCR_LOOP 0x0002 // Controls output pin LBK
421#define TCR_FORCOL 0x0004 // When 1 will force a collision
422#define TCR_PAD_EN 0x0080 // When 1 will pad tx frames < 64 bytes w/0
423#define TCR_NOCRC 0x0100 // When 1 will not append CRC to tx frames
424#define TCR_MON_CSN 0x0400 // When 1 tx monitors carrier
425#define TCR_FDUPLX 0x0800 // When 1 enables full duplex operation
426#define TCR_STP_SQET 0x1000 // When 1 stops tx if Signal Quality Error
427#define TCR_EPH_LOOP 0x2000 // When 1 enables EPH block loopback
428#define TCR_SWFDUP 0x8000 // When 1 enables Switched Full Duplex mode
429
430#define TCR_CLEAR 0 /* do NOTHING */
431/* the default settings for the TCR register : */
432#define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN)
433
434
435// EPH Status Register
436/* BANK 0 */
437#define EPH_STATUS_REG SMC_REG(0x0002, 0)
438#define ES_TX_SUC 0x0001 // Last TX was successful
439#define ES_SNGL_COL 0x0002 // Single collision detected for last tx
440#define ES_MUL_COL 0x0004 // Multiple collisions detected for last tx
441#define ES_LTX_MULT 0x0008 // Last tx was a multicast
442#define ES_16COL 0x0010 // 16 Collisions Reached
443#define ES_SQET 0x0020 // Signal Quality Error Test
444#define ES_LTXBRD 0x0040 // Last tx was a broadcast
445#define ES_TXDEFR 0x0080 // Transmit Deferred
446#define ES_LATCOL 0x0200 // Late collision detected on last tx
447#define ES_LOSTCARR 0x0400 // Lost Carrier Sense
448#define ES_EXC_DEF 0x0800 // Excessive Deferral
449#define ES_CTR_ROL 0x1000 // Counter Roll Over indication
450#define ES_LINK_OK 0x4000 // Driven by inverted value of nLNK pin
451#define ES_TXUNRN 0x8000 // Tx Underrun
452
453
454// Receive Control Register
455/* BANK 0 */
456#define RCR_REG SMC_REG(0x0004, 0)
457#define RCR_RX_ABORT 0x0001 // Set if a rx frame was aborted
458#define RCR_PRMS 0x0002 // Enable promiscuous mode
459#define RCR_ALMUL 0x0004 // When set accepts all multicast frames
460#define RCR_RXEN 0x0100 // IFF this is set, we can receive packets
461#define RCR_STRIP_CRC 0x0200 // When set strips CRC from rx packets
462#define RCR_ABORT_ENB 0x0200 // When set will abort rx on collision
463#define RCR_FILT_CAR 0x0400 // When set filters leading 12 bit s of carrier
464#define RCR_SOFTRST 0x8000 // resets the chip
465
466/* the normal settings for the RCR register : */
467#define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN)
468#define RCR_CLEAR 0x0 // set it to a base state
469
470
471// Counter Register
472/* BANK 0 */
473#define COUNTER_REG SMC_REG(0x0006, 0)
474
475
476// Memory Information Register
477/* BANK 0 */
478#define MIR_REG SMC_REG(0x0008, 0)
479
480
481// Receive/Phy Control Register
482/* BANK 0 */
483#define RPC_REG SMC_REG(0x000A, 0)
484#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
485#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
486#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
487#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
488#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
489#define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect
490#define RPC_LED_RES (0x01) // LED = Reserved
491#define RPC_LED_10 (0x02) // LED = 10Mbps link detect
492#define RPC_LED_FD (0x03) // LED = Full Duplex Mode
493#define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred
494#define RPC_LED_100 (0x05) // LED = 100Mbps link dectect
495#define RPC_LED_TX (0x06) // LED = TX packet occurred
496#define RPC_LED_RX (0x07) // LED = RX packet occurred
497
498#ifndef RPC_LSA_DEFAULT
499#define RPC_LSA_DEFAULT RPC_LED_100
500#endif
501#ifndef RPC_LSB_DEFAULT
502#define RPC_LSB_DEFAULT RPC_LED_FD
503#endif
504
505#define RPC_DEFAULT (RPC_ANEG | (RPC_LSA_DEFAULT << RPC_LSXA_SHFT) | (RPC_LSB_DEFAULT << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
506
507
508/* Bank 0 0x0C is reserved */
509
510// Bank Select Register
511/* All Banks */
512#define BSR_REG 0x000E
513
514
515// Configuration Reg
516/* BANK 1 */
517#define CONFIG_REG SMC_REG(0x0000, 1)
518#define CONFIG_EXT_PHY 0x0200 // 1=external MII, 0=internal Phy
519#define CONFIG_GPCNTRL 0x0400 // Inverse value drives pin nCNTRL
520#define CONFIG_NO_WAIT 0x1000 // When 1 no extra wait states on ISA bus
521#define CONFIG_EPH_POWER_EN 0x8000 // When 0 EPH is placed into low power mode.
522
523// Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low
524#define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN)
525
526
527// Base Address Register
528/* BANK 1 */
529#define BASE_REG SMC_REG(0x0002, 1)
530
531
532// Individual Address Registers
533/* BANK 1 */
534#define ADDR0_REG SMC_REG(0x0004, 1)
535#define ADDR1_REG SMC_REG(0x0006, 1)
536#define ADDR2_REG SMC_REG(0x0008, 1)
537
538
539// General Purpose Register
540/* BANK 1 */
541#define GP_REG SMC_REG(0x000A, 1)
542
543
544// Control Register
545/* BANK 1 */
546#define CTL_REG SMC_REG(0x000C, 1)
547#define CTL_RCV_BAD 0x4000 // When 1 bad CRC packets are received
548#define CTL_AUTO_RELEASE 0x0800 // When 1 tx pages are released automatically
549#define CTL_LE_ENABLE 0x0080 // When 1 enables Link Error interrupt
550#define CTL_CR_ENABLE 0x0040 // When 1 enables Counter Rollover interrupt
551#define CTL_TE_ENABLE 0x0020 // When 1 enables Transmit Error interrupt
552#define CTL_EEPROM_SELECT 0x0004 // Controls EEPROM reload & store
553#define CTL_RELOAD 0x0002 // When set reads EEPROM into registers
554#define CTL_STORE 0x0001 // When set stores registers into EEPROM
555
556
557// MMU Command Register
558/* BANK 2 */
559#define MMU_CMD_REG SMC_REG(0x0000, 2)
560#define MC_BUSY 1 // When 1 the last release has not completed
561#define MC_NOP (0<<5) // No Op
562#define MC_ALLOC (1<<5) // OR with number of 256 byte packets
563#define MC_RESET (2<<5) // Reset MMU to initial state
564#define MC_REMOVE (3<<5) // Remove the current rx packet
565#define MC_RELEASE (4<<5) // Remove and release the current rx packet
566#define MC_FREEPKT (5<<5) // Release packet in PNR register
567#define MC_ENQUEUE (6<<5) // Enqueue the packet for transmit
568#define MC_RSTTXFIFO (7<<5) // Reset the TX FIFOs
569
570
571// Packet Number Register
572/* BANK 2 */
573#define PN_REG SMC_REG(0x0002, 2)
574
575
576// Allocation Result Register
577/* BANK 2 */
578#define AR_REG SMC_REG(0x0003, 2)
579#define AR_FAILED 0x80 // Alocation Failed
580
581
582// TX FIFO Ports Register
583/* BANK 2 */
584#define TXFIFO_REG SMC_REG(0x0004, 2)
585#define TXFIFO_TEMPTY 0x80 // TX FIFO Empty
586
587// RX FIFO Ports Register
588/* BANK 2 */
589#define RXFIFO_REG SMC_REG(0x0005, 2)
590#define RXFIFO_REMPTY 0x80 // RX FIFO Empty
591
592#define FIFO_REG SMC_REG(0x0004, 2)
593
594// Pointer Register
595/* BANK 2 */
596#define PTR_REG SMC_REG(0x0006, 2)
597#define PTR_RCV 0x8000 // 1=Receive area, 0=Transmit area
598#define PTR_AUTOINC 0x4000 // Auto increment the pointer on each access
599#define PTR_READ 0x2000 // When 1 the operation is a read
600
601
602// Data Register
603/* BANK 2 */
604#define DATA_REG SMC_REG(0x0008, 2)
605
606
607// Interrupt Status/Acknowledge Register
608/* BANK 2 */
609#define INT_REG SMC_REG(0x000C, 2)
610
611
612// Interrupt Mask Register
613/* BANK 2 */
614#define IM_REG SMC_REG(0x000D, 2)
615#define IM_MDINT 0x80 // PHY MI Register 18 Interrupt
616#define IM_ERCV_INT 0x40 // Early Receive Interrupt
617#define IM_EPH_INT 0x20 // Set by Ethernet Protocol Handler section
618#define IM_RX_OVRN_INT 0x10 // Set by Receiver Overruns
619#define IM_ALLOC_INT 0x08 // Set when allocation request is completed
620#define IM_TX_EMPTY_INT 0x04 // Set if the TX FIFO goes empty
621#define IM_TX_INT 0x02 // Transmit Interrupt
622#define IM_RCV_INT 0x01 // Receive Interrupt
623
624
625// Multicast Table Registers
626/* BANK 3 */
627#define MCAST_REG1 SMC_REG(0x0000, 3)
628#define MCAST_REG2 SMC_REG(0x0002, 3)
629#define MCAST_REG3 SMC_REG(0x0004, 3)
630#define MCAST_REG4 SMC_REG(0x0006, 3)
631
632
633// Management Interface Register (MII)
634/* BANK 3 */
635#define MII_REG SMC_REG(0x0008, 3)
636#define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup
637#define MII_MDOE 0x0008 // MII Output Enable
638#define MII_MCLK 0x0004 // MII Clock, pin MDCLK
639#define MII_MDI 0x0002 // MII Input, pin MDI
640#define MII_MDO 0x0001 // MII Output, pin MDO
641
642
643// Revision Register
644/* BANK 3 */
645/* ( hi: chip id low: rev # ) */
646#define REV_REG SMC_REG(0x000A, 3)
647
648
649// Early RCV Register
650/* BANK 3 */
651/* this is NOT on SMC9192 */
652#define ERCV_REG SMC_REG(0x000C, 3)
653#define ERCV_RCV_DISCRD 0x0080 // When 1 discards a packet being received
654#define ERCV_THRESHOLD 0x001F // ERCV Threshold Mask
655
656
657// External Register
658/* BANK 7 */
659#define EXT_REG SMC_REG(0x0000, 7)
660
661
662#define CHIP_9192 3
663#define CHIP_9194 4
664#define CHIP_9195 5
665#define CHIP_9196 6
666#define CHIP_91100 7
667#define CHIP_91100FD 8
668#define CHIP_91111FD 9
669
670static const char * chip_ids[ 16 ] = {
671 NULL, NULL, NULL,
672 /* 3 */ "SMC91C90/91C92",
673 /* 4 */ "SMC91C94",
674 /* 5 */ "SMC91C95",
675 /* 6 */ "SMC91C96",
676 /* 7 */ "SMC91C100",
677 /* 8 */ "SMC91C100FD",
678 /* 9 */ "SMC91C11xFD",
679 NULL, NULL, NULL,
680 NULL, NULL, NULL};
681
682
683/*
684 . Transmit status bits
685*/
686#define TS_SUCCESS 0x0001
687#define TS_LOSTCAR 0x0400
688#define TS_LATCOL 0x0200
689#define TS_16COL 0x0010
690
691/*
692 . Receive status bits
693*/
694#define RS_ALGNERR 0x8000
695#define RS_BRODCAST 0x4000
696#define RS_BADCRC 0x2000
697#define RS_ODDFRAME 0x1000
698#define RS_TOOLONG 0x0800
699#define RS_TOOSHORT 0x0400
700#define RS_MULTICAST 0x0001
701#define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
702
703
704/*
705 * PHY IDs
706 * LAN83C183 == LAN91C111 Internal PHY
707 */
708#define PHY_LAN83C183 0x0016f840
709#define PHY_LAN83C180 0x02821c50
710
711/*
712 * PHY Register Addresses (LAN91C111 Internal PHY)
713 *
714 * Generic PHY registers can be found in <linux/mii.h>
715 *
716 * These phy registers are specific to our on-board phy.
717 */
718
719// PHY Configuration Register 1
720#define PHY_CFG1_REG 0x10
721#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
722#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
723#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
724#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
725#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
726#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
727#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
728#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
729#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
730#define PHY_CFG1_TLVL_MASK 0x003C
731#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
732
733
734// PHY Configuration Register 2
735#define PHY_CFG2_REG 0x11
736#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
737#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
738#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
739#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
740
741// PHY Status Output (and Interrupt status) Register
742#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
743#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
744#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
745#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
746#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
747#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
748#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
749#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
750#define PHY_INT_JAB 0x0100 // 1=Jabber detected
751#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
752#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
753
754// PHY Interrupt/Status Mask Register
755#define PHY_MASK_REG 0x13 // Interrupt Mask
756// Uses the same bit definitions as PHY_INT_REG
757
758
759/*
760 * SMC91C96 ethernet config and status registers.
761 * These are in the "attribute" space.
762 */
763#define ECOR 0x8000
764#define ECOR_RESET 0x80
765#define ECOR_LEVEL_IRQ 0x40
766#define ECOR_WR_ATTRIB 0x04
767#define ECOR_ENABLE 0x01
768
769#define ECSR 0x8002
770#define ECSR_IOIS8 0x20
771#define ECSR_PWRDWN 0x04
772#define ECSR_INT 0x02
773
774#define ATTRIB_SIZE ((64*1024) << SMC_IO_SHIFT)
775
776
777/*
778 * Macros to abstract register access according to the data bus
779 * capabilities. Please use those and not the in/out primitives.
780 * Note: the following macros do *not* select the bank -- this must
781 * be done separately as needed in the main code. The SMC_REG() macro
782 * only uses the bank argument for debugging purposes (when enabled).
783 */
784
785#if SMC_DEBUG > 0
786#define SMC_REG(reg, bank) \
787 ({ \
788 int __b = SMC_CURRENT_BANK(); \
789 if (unlikely((__b & ~0xf0) != (0x3300 | bank))) { \
790 printk( "%s: bank reg screwed (0x%04x)\n", \
791 CARDNAME, __b ); \
792 BUG(); \
793 } \
794 reg<<SMC_IO_SHIFT; \
795 })
796#else
797#define SMC_REG(reg, bank) (reg<<SMC_IO_SHIFT)
798#endif
799
800#if SMC_CAN_USE_8BIT
801#define SMC_GET_PN() SMC_inb( ioaddr, PN_REG )
802#define SMC_SET_PN(x) SMC_outb( x, ioaddr, PN_REG )
803#define SMC_GET_AR() SMC_inb( ioaddr, AR_REG )
804#define SMC_GET_TXFIFO() SMC_inb( ioaddr, TXFIFO_REG )
805#define SMC_GET_RXFIFO() SMC_inb( ioaddr, RXFIFO_REG )
806#define SMC_GET_INT() SMC_inb( ioaddr, INT_REG )
807#define SMC_ACK_INT(x) SMC_outb( x, ioaddr, INT_REG )
808#define SMC_GET_INT_MASK() SMC_inb( ioaddr, IM_REG )
809#define SMC_SET_INT_MASK(x) SMC_outb( x, ioaddr, IM_REG )
810#else
811#define SMC_GET_PN() (SMC_inw( ioaddr, PN_REG ) & 0xFF)
812#define SMC_SET_PN(x) SMC_outw( x, ioaddr, PN_REG )
813#define SMC_GET_AR() (SMC_inw( ioaddr, PN_REG ) >> 8)
814#define SMC_GET_TXFIFO() (SMC_inw( ioaddr, TXFIFO_REG ) & 0xFF)
815#define SMC_GET_RXFIFO() (SMC_inw( ioaddr, TXFIFO_REG ) >> 8)
816#define SMC_GET_INT() (SMC_inw( ioaddr, INT_REG ) & 0xFF)
817#define SMC_ACK_INT(x) \
818 do { \
819 unsigned long __flags; \
820 int __mask; \
821 local_irq_save(__flags); \
822 __mask = SMC_inw( ioaddr, INT_REG ) & ~0xff; \
823 SMC_outw( __mask | (x), ioaddr, INT_REG ); \
824 local_irq_restore(__flags); \
825 } while (0)
826#define SMC_GET_INT_MASK() (SMC_inw( ioaddr, INT_REG ) >> 8)
827#define SMC_SET_INT_MASK(x) SMC_outw( (x) << 8, ioaddr, INT_REG )
828#endif
829
830#define SMC_CURRENT_BANK() SMC_inw( ioaddr, BANK_SELECT )
831#define SMC_SELECT_BANK(x) SMC_outw( x, ioaddr, BANK_SELECT )
832#define SMC_GET_BASE() SMC_inw( ioaddr, BASE_REG )
833#define SMC_SET_BASE(x) SMC_outw( x, ioaddr, BASE_REG )
834#define SMC_GET_CONFIG() SMC_inw( ioaddr, CONFIG_REG )
835#define SMC_SET_CONFIG(x) SMC_outw( x, ioaddr, CONFIG_REG )
836#define SMC_GET_COUNTER() SMC_inw( ioaddr, COUNTER_REG )
837#define SMC_GET_CTL() SMC_inw( ioaddr, CTL_REG )
838#define SMC_SET_CTL(x) SMC_outw( x, ioaddr, CTL_REG )
839#define SMC_GET_MII() SMC_inw( ioaddr, MII_REG )
840#define SMC_SET_MII(x) SMC_outw( x, ioaddr, MII_REG )
841#define SMC_GET_MIR() SMC_inw( ioaddr, MIR_REG )
842#define SMC_SET_MIR(x) SMC_outw( x, ioaddr, MIR_REG )
843#define SMC_GET_MMU_CMD() SMC_inw( ioaddr, MMU_CMD_REG )
844#define SMC_SET_MMU_CMD(x) SMC_outw( x, ioaddr, MMU_CMD_REG )
845#define SMC_GET_FIFO() SMC_inw( ioaddr, FIFO_REG )
846#define SMC_GET_PTR() SMC_inw( ioaddr, PTR_REG )
847#define SMC_SET_PTR(x) SMC_outw( x, ioaddr, PTR_REG )
848#define SMC_GET_RCR() SMC_inw( ioaddr, RCR_REG )
849#define SMC_SET_RCR(x) SMC_outw( x, ioaddr, RCR_REG )
850#define SMC_GET_REV() SMC_inw( ioaddr, REV_REG )
851#define SMC_GET_RPC() SMC_inw( ioaddr, RPC_REG )
852#define SMC_SET_RPC(x) SMC_outw( x, ioaddr, RPC_REG )
853#define SMC_GET_TCR() SMC_inw( ioaddr, TCR_REG )
854#define SMC_SET_TCR(x) SMC_outw( x, ioaddr, TCR_REG )
855
856#ifndef SMC_GET_MAC_ADDR
857#define SMC_GET_MAC_ADDR(addr) \
858 do { \
859 unsigned int __v; \
860 __v = SMC_inw( ioaddr, ADDR0_REG ); \
861 addr[0] = __v; addr[1] = __v >> 8; \
862 __v = SMC_inw( ioaddr, ADDR1_REG ); \
863 addr[2] = __v; addr[3] = __v >> 8; \
864 __v = SMC_inw( ioaddr, ADDR2_REG ); \
865 addr[4] = __v; addr[5] = __v >> 8; \
866 } while (0)
867#endif
868
869#define SMC_SET_MAC_ADDR(addr) \
870 do { \
871 SMC_outw( addr[0]|(addr[1] << 8), ioaddr, ADDR0_REG ); \
872 SMC_outw( addr[2]|(addr[3] << 8), ioaddr, ADDR1_REG ); \
873 SMC_outw( addr[4]|(addr[5] << 8), ioaddr, ADDR2_REG ); \
874 } while (0)
875
876#define SMC_SET_MCAST(x) \
877 do { \
878 const unsigned char *mt = (x); \
879 SMC_outw( mt[0] | (mt[1] << 8), ioaddr, MCAST_REG1 ); \
880 SMC_outw( mt[2] | (mt[3] << 8), ioaddr, MCAST_REG2 ); \
881 SMC_outw( mt[4] | (mt[5] << 8), ioaddr, MCAST_REG3 ); \
882 SMC_outw( mt[6] | (mt[7] << 8), ioaddr, MCAST_REG4 ); \
883 } while (0)
884
885#if SMC_CAN_USE_32BIT
886/*
887 * Some setups just can't write 8 or 16 bits reliably when not aligned
888 * to a 32 bit boundary. I tell you that exists!
889 * We re-do the ones here that can be easily worked around if they can have
890 * their low parts written to 0 without adverse effects.
891 */
892#undef SMC_SELECT_BANK
893#define SMC_SELECT_BANK(x) SMC_outl( (x)<<16, ioaddr, 12<<SMC_IO_SHIFT )
894#undef SMC_SET_RPC
895#define SMC_SET_RPC(x) SMC_outl( (x)<<16, ioaddr, SMC_REG(8, 0) )
896#undef SMC_SET_PN
897#define SMC_SET_PN(x) SMC_outl( (x)<<16, ioaddr, SMC_REG(0, 2) )
898#undef SMC_SET_PTR
899#define SMC_SET_PTR(x) SMC_outl( (x)<<16, ioaddr, SMC_REG(4, 2) )
900#endif
901
902#if SMC_CAN_USE_32BIT
903#define SMC_PUT_PKT_HDR(status, length) \
904 SMC_outl( (status) | (length) << 16, ioaddr, DATA_REG )
905#define SMC_GET_PKT_HDR(status, length) \
906 do { \
907 unsigned int __val = SMC_inl( ioaddr, DATA_REG ); \
908 (status) = __val & 0xffff; \
909 (length) = __val >> 16; \
910 } while (0)
911#else
912#define SMC_PUT_PKT_HDR(status, length) \
913 do { \
914 SMC_outw( status, ioaddr, DATA_REG ); \
915 SMC_outw( length, ioaddr, DATA_REG ); \
916 } while (0)
917#define SMC_GET_PKT_HDR(status, length) \
918 do { \
919 (status) = SMC_inw( ioaddr, DATA_REG ); \
920 (length) = SMC_inw( ioaddr, DATA_REG ); \
921 } while (0)
922#endif
923
924#if SMC_CAN_USE_32BIT
925#define _SMC_PUSH_DATA(p, l) \
926 do { \
927 char *__ptr = (p); \
928 int __len = (l); \
929 if (__len >= 2 && (unsigned long)__ptr & 2) { \
930 __len -= 2; \
931 SMC_outw( *(u16 *)__ptr, ioaddr, DATA_REG ); \
932 __ptr += 2; \
933 } \
934 SMC_outsl( ioaddr, DATA_REG, __ptr, __len >> 2); \
935 if (__len & 2) { \
936 __ptr += (__len & ~3); \
937 SMC_outw( *((u16 *)__ptr), ioaddr, DATA_REG ); \
938 } \
939 } while (0)
940#define _SMC_PULL_DATA(p, l) \
941 do { \
942 char *__ptr = (p); \
943 int __len = (l); \
944 if ((unsigned long)__ptr & 2) { \
945 /* \
946 * We want 32bit alignment here. \
947 * Since some buses perform a full 32bit \
948 * fetch even for 16bit data we can't use \
949 * SMC_inw() here. Back both source (on chip \
950 * and destination) pointers of 2 bytes. \
951 */ \
952 __ptr -= 2; \
953 __len += 2; \
954 SMC_SET_PTR( 2|PTR_READ|PTR_RCV|PTR_AUTOINC ); \
955 } \
956 __len += 2; \
957 SMC_insl( ioaddr, DATA_REG, __ptr, __len >> 2); \
958 } while (0)
959#elif SMC_CAN_USE_16BIT
960#define _SMC_PUSH_DATA(p, l) SMC_outsw( ioaddr, DATA_REG, p, (l) >> 1 )
961#define _SMC_PULL_DATA(p, l) SMC_insw ( ioaddr, DATA_REG, p, (l) >> 1 )
962#elif SMC_CAN_USE_8BIT
963#define _SMC_PUSH_DATA(p, l) SMC_outsb( ioaddr, DATA_REG, p, l )
964#define _SMC_PULL_DATA(p, l) SMC_insb ( ioaddr, DATA_REG, p, l )
965#endif
966
967#if ! SMC_CAN_USE_16BIT
968#define SMC_outw(x, ioaddr, reg) \
969 do { \
970 unsigned int __val16 = (x); \
971 SMC_outb( __val16, ioaddr, reg ); \
972 SMC_outb( __val16 >> 8, ioaddr, reg + (1 << SMC_IO_SHIFT));\
973 } while (0)
974#define SMC_inw(ioaddr, reg) \
975 ({ \
976 unsigned int __val16; \
977 __val16 = SMC_inb( ioaddr, reg ); \
978 __val16 |= SMC_inb( ioaddr, reg + (1 << SMC_IO_SHIFT)) << 8; \
979 __val16; \
980 })
981#endif
982
983#if SMC_CAN_USE_DATACS
984#define SMC_PUSH_DATA(p, l) \
985 if ( lp->datacs ) { \
986 unsigned char *__ptr = (p); \
987 int __len = (l); \
988 if (__len >= 2 && (unsigned long)__ptr & 2) { \
989 __len -= 2; \
990 SMC_outw( *((u16 *)__ptr), ioaddr, DATA_REG ); \
991 __ptr += 2; \
992 } \
993 outsl(lp->datacs, __ptr, __len >> 2); \
994 if (__len & 2) { \
995 __ptr += (__len & ~3); \
996 SMC_outw( *((u16 *)__ptr), ioaddr, DATA_REG ); \
997 } \
998 } else { \
999 _SMC_PUSH_DATA(p, l); \
1000 }
1001
1002#define SMC_PULL_DATA(p, l) \
1003 if ( lp->datacs ) { \
1004 unsigned char *__ptr = (p); \
1005 int __len = (l); \
1006 if ((unsigned long)__ptr & 2) { \
1007 /* \
1008 * We want 32bit alignment here. \
1009 * Since some buses perform a full 32bit \
1010 * fetch even for 16bit data we can't use \
1011 * SMC_inw() here. Back both source (on chip \
1012 * and destination) pointers of 2 bytes. \
1013 */ \
1014 __ptr -= 2; \
1015 __len += 2; \
1016 SMC_SET_PTR( 2|PTR_READ|PTR_RCV|PTR_AUTOINC ); \
1017 } \
1018 __len += 2; \
1019 insl( lp->datacs, __ptr, __len >> 2); \
1020 } else { \
1021 _SMC_PULL_DATA(p, l); \
1022 }
1023#else
1024#define SMC_PUSH_DATA(p, l) _SMC_PUSH_DATA(p, l)
1025#define SMC_PULL_DATA(p, l) _SMC_PULL_DATA(p, l)
1026#endif
1027
1028#if !defined (SMC_INTERRUPT_PREAMBLE)
1029# define SMC_INTERRUPT_PREAMBLE
1030#endif
1031
1032#endif /* _SMC91X_H_ */