| Paul Mundt | c2a560f | 2006-10-19 17:31:22 +0900 | [diff] [blame] | 1 | #ifndef __ASM_SH_RENESAS_R7780RP_H |
| 2 | #define __ASM_SH_RENESAS_R7780RP_H |
| 3 | |
| 4 | /* |
| 5 | * linux/include/asm-sh/r7780rp.h |
| 6 | * |
| 7 | * Copyright (C) 2000 Atom Create Engineering Co., Ltd. |
| 8 | * |
| 9 | * Renesas Solutions Highlander R7780RP support |
| 10 | */ |
| 11 | |
| 12 | /* Box specific addresses. */ |
| 13 | #if defined(CONFIG_SH_R7780MP) |
| 14 | #define PA_BCR 0xa4000000 /* FPGA */ |
| 15 | #define PA_IRLMSK (PA_BCR+0x0000) /* Interrupt Mask control */ |
| 16 | #define PA_IRLMON (PA_BCR+0x0002) /* Interrupt Status control */ |
| 17 | #define PA_IRLPRI1 (PA_BCR+0x0004) /* Interrupt Priorty 1 */ |
| 18 | #define PA_IRLPRI2 (PA_BCR+0x0006) /* Interrupt Priorty 2 */ |
| 19 | #define PA_IRLPRI3 (PA_BCR+0x0008) /* Interrupt Priorty 3 */ |
| 20 | #define PA_IRLPRI4 (PA_BCR+0x000a) /* Interrupt Priorty 4 */ |
| 21 | #define PA_RSTCTL (PA_BCR+0x000c) /* Reset Control */ |
| 22 | #define PA_PCIBD (PA_BCR+0x000e) /* PCI Board detect control */ |
| 23 | #define PA_PCICD (PA_BCR+0x0010) /* PCI Conector detect control */ |
| 24 | #define PA_EXTGIO (PA_BCR+0x0016) /* Extension GPIO Control */ |
| 25 | #define PA_IVDRMON (PA_BCR+0x0018) /* iVDR Moniter control */ |
| 26 | #define PA_IVDRCTL (PA_BCR+0x001a) /* iVDR control */ |
| 27 | #define PA_OBLED (PA_BCR+0x001c) /* On Board LED control */ |
| 28 | #define PA_OBSW (PA_BCR+0x001e) /* On Board Switch control */ |
| 29 | #define PA_AUDIOSEL (PA_BCR+0x0020) /* Sound Interface Select control */ |
| 30 | #define PA_EXTPLR (PA_BCR+0x001e) /* Extention Pin Polarity control */ |
| 31 | #define PA_TPCTL (PA_BCR+0x0100) /* Touch Panel Access control */ |
| 32 | #define PA_TPDCKCTL (PA_BCR+0x0102) /* Touch Panel Access data control */ |
| 33 | #define PA_TPCTLCLR (PA_BCR+0x0104) /* Touch Panel Access control */ |
| 34 | #define PA_TPXPOS (PA_BCR+0x0106) /* Touch Panel X position control */ |
| 35 | #define PA_TPYPOS (PA_BCR+0x0108) /* Touch Panel Y position control */ |
| 36 | #define PA_DBSW (PA_BCR+0x0200) /* Debug Board Switch control */ |
| 37 | #define PA_CFCTL (PA_BCR+0x0300) /* CF Timing control */ |
| 38 | #define PA_CFPOW (PA_BCR+0x0302) /* CF Power control */ |
| 39 | #define PA_CFCDINTCLR (PA_BCR+0x0304) /* CF Insert Interrupt clear */ |
| 40 | #define PA_SCSMR0 (PA_BCR+0x0400) /* SCIF0 Serial mode control */ |
| 41 | #define PA_SCBRR0 (PA_BCR+0x0404) /* SCIF0 Bit rate control */ |
| 42 | #define PA_SCSCR0 (PA_BCR+0x0408) /* SCIF0 Serial control */ |
| 43 | #define PA_SCFTDR0 (PA_BCR+0x040c) /* SCIF0 Send FIFO control */ |
| 44 | #define PA_SCFSR0 (PA_BCR+0x0410) /* SCIF0 Serial status control */ |
| 45 | #define PA_SCFRDR0 (PA_BCR+0x0414) /* SCIF0 Receive FIFO control */ |
| 46 | #define PA_SCFCR0 (PA_BCR+0x0418) /* SCIF0 FIFO control */ |
| 47 | #define PA_SCTFDR0 (PA_BCR+0x041c) /* SCIF0 Send FIFO data control */ |
| 48 | #define PA_SCRFDR0 (PA_BCR+0x0420) /* SCIF0 Receive FIFO data control */ |
| 49 | #define PA_SCSPTR0 (PA_BCR+0x0424) /* SCIF0 Serial Port control */ |
| 50 | #define PA_SCLSR0 (PA_BCR+0x0428) /* SCIF0 Line Status control */ |
| 51 | #define PA_SCRER0 (PA_BCR+0x042c) /* SCIF0 Serial Error control */ |
| 52 | #define PA_SCSMR1 (PA_BCR+0x0500) /* SCIF1 Serial mode control */ |
| 53 | #define PA_SCBRR1 (PA_BCR+0x0504) /* SCIF1 Bit rate control */ |
| 54 | #define PA_SCSCR1 (PA_BCR+0x0508) /* SCIF1 Serial control */ |
| 55 | #define PA_SCFTDR1 (PA_BCR+0x050c) /* SCIF1 Send FIFO control */ |
| 56 | #define PA_SCFSR1 (PA_BCR+0x0510) /* SCIF1 Serial status control */ |
| 57 | #define PA_SCFRDR1 (PA_BCR+0x0514) /* SCIF1 Receive FIFO control */ |
| 58 | #define PA_SCFCR1 (PA_BCR+0x0518) /* SCIF1 FIFO control */ |
| 59 | #define PA_SCTFDR1 (PA_BCR+0x051c) /* SCIF1 Send FIFO data control */ |
| 60 | #define PA_SCRFDR1 (PA_BCR+0x0520) /* SCIF1 Receive FIFO data control */ |
| 61 | #define PA_SCSPTR1 (PA_BCR+0x0524) /* SCIF1 Serial Port control */ |
| 62 | #define PA_SCLSR1 (PA_BCR+0x0528) /* SCIF1 Line Status control */ |
| 63 | #define PA_SCRER1 (PA_BCR+0x052c) /* SCIF1 Serial Error control */ |
| 64 | #define PA_ICCR (PA_BCR+0x0600) /* Serial control */ |
| 65 | #define PA_SAR (PA_BCR+0x0602) /* Serial Slave control */ |
| 66 | #define PA_MDR (PA_BCR+0x0604) /* Serial Mode control */ |
| 67 | #define PA_ADR1 (PA_BCR+0x0606) /* Serial Address1 control */ |
| 68 | #define PA_DAR1 (PA_BCR+0x0646) /* Serial Data1 control */ |
| 69 | #define PA_VERREG (PA_BCR+0x0700) /* FPGA Version Register */ |
| 70 | #define PA_POFF (PA_BCR+0x0800) /* System Power Off control */ |
| 71 | #define PA_PMR (PA_BCR+0x0900) /* */ |
| 72 | |
| 73 | #define PA_AX88796L 0xa4100400 /* AX88796L Area */ |
| 74 | #define PA_SC1602BSLB 0xa6000000 /* SC1602BSLB Area */ |
| 75 | #define PA_IDE_OFFSET 0x1f0 /* CF IDE Offset */ |
| 76 | #define AX88796L_IO_BASE 0x1000 /* AX88796L IO Base Address */ |
| 77 | |
| 78 | #define IRLCNTR1 (PA_BCR + 0) /* Interrupt Control Register1 */ |
| 79 | |
| 80 | #define IRQ_PCISLOT1 65 /* PCI Slot #1 IRQ */ |
| 81 | #define IRQ_PCISLOT2 66 /* PCI Slot #2 IRQ */ |
| 82 | #define IRQ_PCISLOT3 67 /* PCI Slot #3 IRQ */ |
| 83 | #define IRQ_PCISLOT4 68 /* PCI Slot #4 IRQ */ |
| Paul Mundt | c2a560f | 2006-10-19 17:31:22 +0900 | [diff] [blame] | 84 | // #define IRQ_CFINST 0 /* CF Card Insert IRQ */ |
| 85 | #define IRQ_TP 2 /* Touch Panel IRQ */ |
| 86 | #define IRQ_SCI1 3 /* SCI1 IRQ */ |
| 87 | #define IRQ_SCI0 4 /* SCI0 IRQ */ |
| 88 | #define IRQ_2SERIAL 5 /* Serial IRQ */ |
| 89 | #define IRQ_RTC 6 /* RTC A / B IRQ */ |
| 90 | #define IRQ_EXTENTION6 7 /* EXT6n IRQ */ |
| 91 | #define IRQ_EXTENTION5 8 /* EXT5n IRQ */ |
| 92 | #define IRQ_EXTENTION4 9 /* EXT4n IRQ */ |
| 93 | #define IRQ_EXTENTION2 10 /* EXT2n IRQ */ |
| 94 | #define IRQ_EXTENTION1 11 /* EXT1n IRQ */ |
| 95 | #define IRQ_ONETH 13 /* On board Ethernet IRQ */ |
| 96 | #define IRQ_PSW 14 /* Push Switch IRQ */ |
| 97 | |
| 98 | #else /* R7780RP */ |
| 99 | |
| 100 | #define PA_BCR 0xa5000000 /* FPGA */ |
| 101 | #define PA_IRLMSK (PA_BCR+0x0000) /* Interrupt Mask control */ |
| 102 | #define PA_IRLMON (PA_BCR+0x0002) /* Interrupt Status control */ |
| 103 | #define PA_SDPOW (PA_BCR+0x0004) /* SD Power control */ |
| 104 | #define PA_RSTCTL (PA_BCR+0x0006) /* Device Reset control */ |
| 105 | #define PA_PCIBD (PA_BCR+0x0008) /* PCI Board detect control */ |
| 106 | #define PA_PCICD (PA_BCR+0x000a) /* PCI Conector detect control */ |
| 107 | #define PA_ZIGIO1 (PA_BCR+0x000c) /* Zigbee IO control 1 */ |
| 108 | #define PA_ZIGIO2 (PA_BCR+0x000e) /* Zigbee IO control 2 */ |
| 109 | #define PA_ZIGIO3 (PA_BCR+0x0010) /* Zigbee IO control 3 */ |
| 110 | #define PA_ZIGIO4 (PA_BCR+0x0012) /* Zigbee IO control 4 */ |
| 111 | #define PA_IVDRMON (PA_BCR+0x0014) /* iVDR Moniter control */ |
| 112 | #define PA_IVDRCTL (PA_BCR+0x0016) /* iVDR control */ |
| 113 | #define PA_OBLED (PA_BCR+0x0018) /* On Board LED control */ |
| 114 | #define PA_OBSW (PA_BCR+0x001a) /* On Board Switch control */ |
| 115 | #define PA_AUDIOSEL (PA_BCR+0x001c) /* Sound Interface Select control */ |
| 116 | #define PA_EXTPLR (PA_BCR+0x001e) /* Extention Pin Polarity control */ |
| 117 | #define PA_TPCTL (PA_BCR+0x0100) /* Touch Panel Access control */ |
| 118 | #define PA_TPDCKCTL (PA_BCR+0x0102) /* Touch Panel Access data control */ |
| 119 | #define PA_TPCTLCLR (PA_BCR+0x0104) /* Touch Panel Access control */ |
| 120 | #define PA_TPXPOS (PA_BCR+0x0106) /* Touch Panel X position control */ |
| 121 | #define PA_TPYPOS (PA_BCR+0x0108) /* Touch Panel Y position control */ |
| 122 | #define PA_DBDET (PA_BCR+0x0200) /* Debug Board detect control */ |
| 123 | #define PA_DBDISPCTL (PA_BCR+0x0202) /* Debug Board Dot timing control */ |
| 124 | #define PA_DBSW (PA_BCR+0x0204) /* Debug Board Switch control */ |
| 125 | #define PA_CFCTL (PA_BCR+0x0300) /* CF Timing control */ |
| 126 | #define PA_CFPOW (PA_BCR+0x0302) /* CF Power control */ |
| 127 | #define PA_CFCDINTCLR (PA_BCR+0x0304) /* CF Insert Interrupt clear */ |
| 128 | #define PA_SCSMR (PA_BCR+0x0400) /* SCIF Serial mode control */ |
| 129 | #define PA_SCBRR (PA_BCR+0x0402) /* SCIF Bit rate control */ |
| 130 | #define PA_SCSCR (PA_BCR+0x0404) /* SCIF Serial control */ |
| 131 | #define PA_SCFDTR (PA_BCR+0x0406) /* SCIF Send FIFO control */ |
| 132 | #define PA_SCFSR (PA_BCR+0x0408) /* SCIF Serial status control */ |
| 133 | #define PA_SCFRDR (PA_BCR+0x040a) /* SCIF Receive FIFO control */ |
| 134 | #define PA_SCFCR (PA_BCR+0x040c) /* SCIF FIFO control */ |
| 135 | #define PA_SCFDR (PA_BCR+0x040e) /* SCIF FIFO data control */ |
| 136 | #define PA_SCLSR (PA_BCR+0x0412) /* SCIF Line Status control */ |
| 137 | #define PA_ICCR (PA_BCR+0x0500) /* Serial control */ |
| 138 | #define PA_SAR (PA_BCR+0x0502) /* Serial Slave control */ |
| 139 | #define PA_MDR (PA_BCR+0x0504) /* Serial Mode control */ |
| 140 | #define PA_ADR1 (PA_BCR+0x0506) /* Serial Address1 control */ |
| 141 | #define PA_DAR1 (PA_BCR+0x0546) /* Serial Data1 control */ |
| 142 | #define PA_VERREG (PA_BCR+0x0600) /* FPGA Version Register */ |
| 143 | |
| 144 | #define PA_AX88796L 0xa5800400 /* AX88796L Area */ |
| 145 | #define PA_SC1602BSLB 0xa6000000 /* SC1602BSLB Area */ |
| 146 | #define PA_IDE_OFFSET 0x1f0 /* CF IDE Offset */ |
| 147 | #define AX88796L_IO_BASE 0x1000 /* AX88796L IO Base Address */ |
| 148 | |
| 149 | #define IRLCNTR1 (PA_BCR + 0) /* Interrupt Control Register1 */ |
| 150 | |
| 151 | #define IRQ_PCISLOT1 0 /* PCI Slot #1 IRQ */ |
| 152 | #define IRQ_PCISLOT2 1 /* PCI Slot #2 IRQ */ |
| 153 | #define IRQ_PCISLOT3 2 /* PCI Slot #3 IRQ */ |
| 154 | #define IRQ_PCISLOT4 3 /* PCI Slot #4 IRQ */ |
| Paul Mundt | c2a560f | 2006-10-19 17:31:22 +0900 | [diff] [blame] | 155 | #define IRQ_CFINST 5 /* CF Card Insert IRQ */ |
| 156 | #define IRQ_M66596 6 /* M66596 IRQ */ |
| 157 | #define IRQ_SDCARD 7 /* SD Card IRQ */ |
| 158 | #define IRQ_TUCHPANEL 8 /* Touch Panel IRQ */ |
| 159 | #define IRQ_SCI 9 /* SCI IRQ */ |
| 160 | #define IRQ_2SERIAL 10 /* Serial IRQ */ |
| 161 | #define IRQ_EXTENTION 11 /* EXTn IRQ */ |
| 162 | #define IRQ_ONETH 12 /* On board Ethernet IRQ */ |
| 163 | #define IRQ_PSW 13 /* Push Switch IRQ */ |
| 164 | #define IRQ_ZIGBEE 14 /* Ziggbee IO IRQ */ |
| 165 | |
| 166 | #endif /* CONFIG_SH_R7780MP */ |
| 167 | |
| 168 | #define __IO_PREFIX r7780rp |
| 169 | #include <asm/io_generic.h> |
| 170 | |
| 171 | #endif /* __ASM_SH_RENESAS_R7780RP */ |