David Gibson | 1d3bb99 | 2007-08-23 13:56:01 +1000 | [diff] [blame] | 1 | /* |
| 2 | * drivers/net/ibm_newemac/phy.c |
| 3 | * |
| 4 | * Driver for PowerPC 4xx on-chip ethernet controller, PHY support. |
| 5 | * Borrowed from sungem_phy.c, though I only kept the generic MII |
| 6 | * driver for now. |
| 7 | * |
| 8 | * This file should be shared with other drivers or eventually |
| 9 | * merged as the "low level" part of miilib |
| 10 | * |
| 11 | * (c) 2003, Benjamin Herrenscmidt (benh@kernel.crashing.org) |
| 12 | * (c) 2004-2005, Eugene Surovegin <ebs@ebshome.net> |
| 13 | * |
| 14 | */ |
| 15 | #include <linux/module.h> |
| 16 | #include <linux/kernel.h> |
| 17 | #include <linux/types.h> |
| 18 | #include <linux/netdevice.h> |
| 19 | #include <linux/mii.h> |
| 20 | #include <linux/ethtool.h> |
| 21 | #include <linux/delay.h> |
| 22 | |
| 23 | #include "emac.h" |
| 24 | #include "phy.h" |
| 25 | |
| 26 | static inline int phy_read(struct mii_phy *phy, int reg) |
| 27 | { |
| 28 | return phy->mdio_read(phy->dev, phy->address, reg); |
| 29 | } |
| 30 | |
| 31 | static inline void phy_write(struct mii_phy *phy, int reg, int val) |
| 32 | { |
| 33 | phy->mdio_write(phy->dev, phy->address, reg, val); |
| 34 | } |
| 35 | |
| 36 | int emac_mii_reset_phy(struct mii_phy *phy) |
| 37 | { |
| 38 | int val; |
| 39 | int limit = 10000; |
| 40 | |
| 41 | val = phy_read(phy, MII_BMCR); |
| 42 | val &= ~(BMCR_ISOLATE | BMCR_ANENABLE); |
| 43 | val |= BMCR_RESET; |
| 44 | phy_write(phy, MII_BMCR, val); |
| 45 | |
| 46 | udelay(300); |
| 47 | |
| 48 | while (limit--) { |
| 49 | val = phy_read(phy, MII_BMCR); |
| 50 | if (val >= 0 && (val & BMCR_RESET) == 0) |
| 51 | break; |
| 52 | udelay(10); |
| 53 | } |
| 54 | if ((val & BMCR_ISOLATE) && limit > 0) |
| 55 | phy_write(phy, MII_BMCR, val & ~BMCR_ISOLATE); |
| 56 | |
| 57 | return limit <= 0; |
| 58 | } |
| 59 | |
| 60 | static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise) |
| 61 | { |
| 62 | int ctl, adv; |
| 63 | |
| 64 | phy->autoneg = AUTONEG_ENABLE; |
| 65 | phy->speed = SPEED_10; |
| 66 | phy->duplex = DUPLEX_HALF; |
| 67 | phy->pause = phy->asym_pause = 0; |
| 68 | phy->advertising = advertise; |
| 69 | |
| 70 | ctl = phy_read(phy, MII_BMCR); |
| 71 | if (ctl < 0) |
| 72 | return ctl; |
| 73 | ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); |
| 74 | |
| 75 | /* First clear the PHY */ |
| 76 | phy_write(phy, MII_BMCR, ctl); |
| 77 | |
| 78 | /* Setup standard advertise */ |
| 79 | adv = phy_read(phy, MII_ADVERTISE); |
| 80 | if (adv < 0) |
| 81 | return adv; |
| 82 | adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4 | ADVERTISE_PAUSE_CAP | |
| 83 | ADVERTISE_PAUSE_ASYM); |
| 84 | if (advertise & ADVERTISED_10baseT_Half) |
| 85 | adv |= ADVERTISE_10HALF; |
| 86 | if (advertise & ADVERTISED_10baseT_Full) |
| 87 | adv |= ADVERTISE_10FULL; |
| 88 | if (advertise & ADVERTISED_100baseT_Half) |
| 89 | adv |= ADVERTISE_100HALF; |
| 90 | if (advertise & ADVERTISED_100baseT_Full) |
| 91 | adv |= ADVERTISE_100FULL; |
| 92 | if (advertise & ADVERTISED_Pause) |
| 93 | adv |= ADVERTISE_PAUSE_CAP; |
| 94 | if (advertise & ADVERTISED_Asym_Pause) |
| 95 | adv |= ADVERTISE_PAUSE_ASYM; |
| 96 | phy_write(phy, MII_ADVERTISE, adv); |
| 97 | |
| 98 | if (phy->features & |
| 99 | (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) { |
| 100 | adv = phy_read(phy, MII_CTRL1000); |
| 101 | if (adv < 0) |
| 102 | return adv; |
| 103 | adv &= ~(ADVERTISE_1000FULL | ADVERTISE_1000HALF); |
| 104 | if (advertise & ADVERTISED_1000baseT_Full) |
| 105 | adv |= ADVERTISE_1000FULL; |
| 106 | if (advertise & ADVERTISED_1000baseT_Half) |
| 107 | adv |= ADVERTISE_1000HALF; |
| 108 | phy_write(phy, MII_CTRL1000, adv); |
| 109 | } |
| 110 | |
| 111 | /* Start/Restart aneg */ |
| 112 | ctl = phy_read(phy, MII_BMCR); |
| 113 | ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); |
| 114 | phy_write(phy, MII_BMCR, ctl); |
| 115 | |
| 116 | return 0; |
| 117 | } |
| 118 | |
| 119 | static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd) |
| 120 | { |
| 121 | int ctl; |
| 122 | |
| 123 | phy->autoneg = AUTONEG_DISABLE; |
| 124 | phy->speed = speed; |
| 125 | phy->duplex = fd; |
| 126 | phy->pause = phy->asym_pause = 0; |
| 127 | |
| 128 | ctl = phy_read(phy, MII_BMCR); |
| 129 | if (ctl < 0) |
| 130 | return ctl; |
| 131 | ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); |
| 132 | |
| 133 | /* First clear the PHY */ |
| 134 | phy_write(phy, MII_BMCR, ctl | BMCR_RESET); |
| 135 | |
| 136 | /* Select speed & duplex */ |
| 137 | switch (speed) { |
| 138 | case SPEED_10: |
| 139 | break; |
| 140 | case SPEED_100: |
| 141 | ctl |= BMCR_SPEED100; |
| 142 | break; |
| 143 | case SPEED_1000: |
| 144 | ctl |= BMCR_SPEED1000; |
| 145 | break; |
| 146 | default: |
| 147 | return -EINVAL; |
| 148 | } |
| 149 | if (fd == DUPLEX_FULL) |
| 150 | ctl |= BMCR_FULLDPLX; |
| 151 | phy_write(phy, MII_BMCR, ctl); |
| 152 | |
| 153 | return 0; |
| 154 | } |
| 155 | |
| 156 | static int genmii_poll_link(struct mii_phy *phy) |
| 157 | { |
| 158 | int status; |
| 159 | |
| 160 | /* Clear latched value with dummy read */ |
| 161 | phy_read(phy, MII_BMSR); |
| 162 | status = phy_read(phy, MII_BMSR); |
| 163 | if (status < 0 || (status & BMSR_LSTATUS) == 0) |
| 164 | return 0; |
| 165 | if (phy->autoneg == AUTONEG_ENABLE && !(status & BMSR_ANEGCOMPLETE)) |
| 166 | return 0; |
| 167 | return 1; |
| 168 | } |
| 169 | |
| 170 | static int genmii_read_link(struct mii_phy *phy) |
| 171 | { |
| 172 | if (phy->autoneg == AUTONEG_ENABLE) { |
| 173 | int glpa = 0; |
| 174 | int lpa = phy_read(phy, MII_LPA) & phy_read(phy, MII_ADVERTISE); |
| 175 | if (lpa < 0) |
| 176 | return lpa; |
| 177 | |
| 178 | if (phy->features & |
| 179 | (SUPPORTED_1000baseT_Full | SUPPORTED_1000baseT_Half)) { |
| 180 | int adv = phy_read(phy, MII_CTRL1000); |
| 181 | glpa = phy_read(phy, MII_STAT1000); |
| 182 | |
| 183 | if (glpa < 0 || adv < 0) |
| 184 | return adv; |
| 185 | |
| 186 | glpa &= adv << 2; |
| 187 | } |
| 188 | |
| 189 | phy->speed = SPEED_10; |
| 190 | phy->duplex = DUPLEX_HALF; |
| 191 | phy->pause = phy->asym_pause = 0; |
| 192 | |
| 193 | if (glpa & (LPA_1000FULL | LPA_1000HALF)) { |
| 194 | phy->speed = SPEED_1000; |
| 195 | if (glpa & LPA_1000FULL) |
| 196 | phy->duplex = DUPLEX_FULL; |
| 197 | } else if (lpa & (LPA_100FULL | LPA_100HALF)) { |
| 198 | phy->speed = SPEED_100; |
| 199 | if (lpa & LPA_100FULL) |
| 200 | phy->duplex = DUPLEX_FULL; |
| 201 | } else if (lpa & LPA_10FULL) |
| 202 | phy->duplex = DUPLEX_FULL; |
| 203 | |
| 204 | if (phy->duplex == DUPLEX_FULL) { |
| 205 | phy->pause = lpa & LPA_PAUSE_CAP ? 1 : 0; |
| 206 | phy->asym_pause = lpa & LPA_PAUSE_ASYM ? 1 : 0; |
| 207 | } |
| 208 | } else { |
| 209 | int bmcr = phy_read(phy, MII_BMCR); |
| 210 | if (bmcr < 0) |
| 211 | return bmcr; |
| 212 | |
| 213 | if (bmcr & BMCR_FULLDPLX) |
| 214 | phy->duplex = DUPLEX_FULL; |
| 215 | else |
| 216 | phy->duplex = DUPLEX_HALF; |
| 217 | if (bmcr & BMCR_SPEED1000) |
| 218 | phy->speed = SPEED_1000; |
| 219 | else if (bmcr & BMCR_SPEED100) |
| 220 | phy->speed = SPEED_100; |
| 221 | else |
| 222 | phy->speed = SPEED_10; |
| 223 | |
| 224 | phy->pause = phy->asym_pause = 0; |
| 225 | } |
| 226 | return 0; |
| 227 | } |
| 228 | |
| 229 | /* Generic implementation for most 10/100/1000 PHYs */ |
| 230 | static struct mii_phy_ops generic_phy_ops = { |
| 231 | .setup_aneg = genmii_setup_aneg, |
| 232 | .setup_forced = genmii_setup_forced, |
| 233 | .poll_link = genmii_poll_link, |
| 234 | .read_link = genmii_read_link |
| 235 | }; |
| 236 | |
| 237 | static struct mii_phy_def genmii_phy_def = { |
| 238 | .phy_id = 0x00000000, |
| 239 | .phy_id_mask = 0x00000000, |
| 240 | .name = "Generic MII", |
| 241 | .ops = &generic_phy_ops |
| 242 | }; |
| 243 | |
| 244 | /* CIS8201 */ |
| 245 | #define MII_CIS8201_10BTCSR 0x16 |
| 246 | #define TENBTCSR_ECHO_DISABLE 0x2000 |
| 247 | #define MII_CIS8201_EPCR 0x17 |
| 248 | #define EPCR_MODE_MASK 0x3000 |
| 249 | #define EPCR_GMII_MODE 0x0000 |
| 250 | #define EPCR_RGMII_MODE 0x1000 |
| 251 | #define EPCR_TBI_MODE 0x2000 |
| 252 | #define EPCR_RTBI_MODE 0x3000 |
| 253 | #define MII_CIS8201_ACSR 0x1c |
| 254 | #define ACSR_PIN_PRIO_SELECT 0x0004 |
| 255 | |
| 256 | static int cis8201_init(struct mii_phy *phy) |
| 257 | { |
| 258 | int epcr; |
| 259 | |
| 260 | epcr = phy_read(phy, MII_CIS8201_EPCR); |
| 261 | if (epcr < 0) |
| 262 | return epcr; |
| 263 | |
| 264 | epcr &= ~EPCR_MODE_MASK; |
| 265 | |
| 266 | switch (phy->mode) { |
| 267 | case PHY_MODE_TBI: |
| 268 | epcr |= EPCR_TBI_MODE; |
| 269 | break; |
| 270 | case PHY_MODE_RTBI: |
| 271 | epcr |= EPCR_RTBI_MODE; |
| 272 | break; |
| 273 | case PHY_MODE_GMII: |
| 274 | epcr |= EPCR_GMII_MODE; |
| 275 | break; |
| 276 | case PHY_MODE_RGMII: |
| 277 | default: |
| 278 | epcr |= EPCR_RGMII_MODE; |
| 279 | } |
| 280 | |
| 281 | phy_write(phy, MII_CIS8201_EPCR, epcr); |
| 282 | |
| 283 | /* MII regs override strap pins */ |
| 284 | phy_write(phy, MII_CIS8201_ACSR, |
| 285 | phy_read(phy, MII_CIS8201_ACSR) | ACSR_PIN_PRIO_SELECT); |
| 286 | |
| 287 | /* Disable TX_EN -> CRS echo mode, otherwise 10/HDX doesn't work */ |
| 288 | phy_write(phy, MII_CIS8201_10BTCSR, |
| 289 | phy_read(phy, MII_CIS8201_10BTCSR) | TENBTCSR_ECHO_DISABLE); |
| 290 | |
| 291 | return 0; |
| 292 | } |
| 293 | |
| 294 | static struct mii_phy_ops cis8201_phy_ops = { |
| 295 | .init = cis8201_init, |
| 296 | .setup_aneg = genmii_setup_aneg, |
| 297 | .setup_forced = genmii_setup_forced, |
| 298 | .poll_link = genmii_poll_link, |
| 299 | .read_link = genmii_read_link |
| 300 | }; |
| 301 | |
| 302 | static struct mii_phy_def cis8201_phy_def = { |
| 303 | .phy_id = 0x000fc410, |
| 304 | .phy_id_mask = 0x000ffff0, |
| 305 | .name = "CIS8201 Gigabit Ethernet", |
| 306 | .ops = &cis8201_phy_ops |
| 307 | }; |
| 308 | |
Stefan Roese | f1f304f | 2007-12-05 11:14:25 +1100 | [diff] [blame^] | 309 | static struct mii_phy_def bcm5248_phy_def = { |
| 310 | |
| 311 | .phy_id = 0x0143bc00, |
| 312 | .phy_id_mask = 0x0ffffff0, |
| 313 | .name = "BCM5248 10/100 SMII Ethernet", |
| 314 | .ops = &generic_phy_ops |
| 315 | }; |
| 316 | |
| 317 | static int m88e1111_init(struct mii_phy *phy) |
| 318 | { |
| 319 | pr_debug("%s: Marvell 88E1111 Ethernet\n", __FUNCTION__); |
| 320 | phy_write(phy, 0x14, 0x0ce3); |
| 321 | phy_write(phy, 0x18, 0x4101); |
| 322 | phy_write(phy, 0x09, 0x0e00); |
| 323 | phy_write(phy, 0x04, 0x01e1); |
| 324 | phy_write(phy, 0x00, 0x9140); |
| 325 | phy_write(phy, 0x00, 0x1140); |
| 326 | |
| 327 | return 0; |
| 328 | } |
| 329 | |
| 330 | static struct mii_phy_ops m88e1111_phy_ops = { |
| 331 | .init = m88e1111_init, |
| 332 | .setup_aneg = genmii_setup_aneg, |
| 333 | .setup_forced = genmii_setup_forced, |
| 334 | .poll_link = genmii_poll_link, |
| 335 | .read_link = genmii_read_link |
| 336 | }; |
| 337 | |
| 338 | static struct mii_phy_def m88e1111_phy_def = { |
| 339 | |
| 340 | .phy_id = 0x01410CC0, |
| 341 | .phy_id_mask = 0x0ffffff0, |
| 342 | .name = "Marvell 88E1111 Ethernet", |
| 343 | .ops = &m88e1111_phy_ops, |
| 344 | }; |
| 345 | |
David Gibson | 1d3bb99 | 2007-08-23 13:56:01 +1000 | [diff] [blame] | 346 | static struct mii_phy_def *mii_phy_table[] = { |
| 347 | &cis8201_phy_def, |
Stefan Roese | f1f304f | 2007-12-05 11:14:25 +1100 | [diff] [blame^] | 348 | &bcm5248_phy_def, |
| 349 | &m88e1111_phy_def, |
David Gibson | 1d3bb99 | 2007-08-23 13:56:01 +1000 | [diff] [blame] | 350 | &genmii_phy_def, |
| 351 | NULL |
| 352 | }; |
| 353 | |
| 354 | int emac_mii_phy_probe(struct mii_phy *phy, int address) |
| 355 | { |
| 356 | struct mii_phy_def *def; |
| 357 | int i; |
| 358 | u32 id; |
| 359 | |
| 360 | phy->autoneg = AUTONEG_DISABLE; |
| 361 | phy->advertising = 0; |
| 362 | phy->address = address; |
| 363 | phy->speed = SPEED_10; |
| 364 | phy->duplex = DUPLEX_HALF; |
| 365 | phy->pause = phy->asym_pause = 0; |
| 366 | |
| 367 | /* Take PHY out of isolate mode and reset it. */ |
| 368 | if (emac_mii_reset_phy(phy)) |
| 369 | return -ENODEV; |
| 370 | |
| 371 | /* Read ID and find matching entry */ |
| 372 | id = (phy_read(phy, MII_PHYSID1) << 16) | phy_read(phy, MII_PHYSID2); |
| 373 | for (i = 0; (def = mii_phy_table[i]) != NULL; i++) |
| 374 | if ((id & def->phy_id_mask) == def->phy_id) |
| 375 | break; |
| 376 | /* Should never be NULL (we have a generic entry), but... */ |
| 377 | if (!def) |
| 378 | return -ENODEV; |
| 379 | |
| 380 | phy->def = def; |
| 381 | |
| 382 | /* Determine PHY features if needed */ |
| 383 | phy->features = def->features; |
| 384 | if (!phy->features) { |
| 385 | u16 bmsr = phy_read(phy, MII_BMSR); |
| 386 | if (bmsr & BMSR_ANEGCAPABLE) |
| 387 | phy->features |= SUPPORTED_Autoneg; |
| 388 | if (bmsr & BMSR_10HALF) |
| 389 | phy->features |= SUPPORTED_10baseT_Half; |
| 390 | if (bmsr & BMSR_10FULL) |
| 391 | phy->features |= SUPPORTED_10baseT_Full; |
| 392 | if (bmsr & BMSR_100HALF) |
| 393 | phy->features |= SUPPORTED_100baseT_Half; |
| 394 | if (bmsr & BMSR_100FULL) |
| 395 | phy->features |= SUPPORTED_100baseT_Full; |
| 396 | if (bmsr & BMSR_ESTATEN) { |
| 397 | u16 esr = phy_read(phy, MII_ESTATUS); |
| 398 | if (esr & ESTATUS_1000_TFULL) |
| 399 | phy->features |= SUPPORTED_1000baseT_Full; |
| 400 | if (esr & ESTATUS_1000_THALF) |
| 401 | phy->features |= SUPPORTED_1000baseT_Half; |
| 402 | } |
| 403 | phy->features |= SUPPORTED_MII; |
| 404 | } |
| 405 | |
| 406 | /* Setup default advertising */ |
| 407 | phy->advertising = phy->features; |
| 408 | |
| 409 | return 0; |
| 410 | } |
| 411 | |
| 412 | MODULE_LICENSE("GPL"); |