arch/arm/mach-ux500/board-mop500.h

/*
 * Copyright (C) ST-Ericsson SA 2010
 *
 * License terms: GNU General Public License (GPL) version 2
 */

#ifndef __BOARD_MOP500_H
#define __BOARD_MOP500_H

/* For NOMADIK_NR_GPIO */
#include <mach/irqs.h>
#include <mach/msp.h>
#include <linux/amba/mmci.h>

/* Snowball specific GPIO assignments, this board has no GPIO expander */
#define SNOWBALL_ACCEL_INT1_GPIO	163
#define SNOWBALL_ACCEL_INT2_GPIO	164
#define SNOWBALL_MAGNET_DRDY_GPIO	165
#define SNOWBALL_SDMMC_EN_GPIO		217
#define SNOWBALL_SDMMC_1V8_3V_GPIO	228
#define SNOWBALL_SDMMC_CD_GPIO		218

/* HREFv60-specific GPIO assignments, this board has no GPIO expander */
#define HREFV60_SDMMC_1V8_3V_GPIO	5
#define HREFV60_CAMERA_FLASH_ENABLE	21
#define HREFV60_MAGNET_DRDY_GPIO	32
#define HREFV60_DISP1_RST_GPIO		65
#define HREFV60_DISP2_RST_GPIO		66
#define HREFV60_ACCEL_INT1_GPIO		82
#define HREFV60_ACCEL_INT2_GPIO		83
#define HREFV60_SDMMC_CD_GPIO		95
#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140
#define HREFV60_TOUCH_RST_GPIO		143
#define HREFV60_HAL_SW_GPIO		145
#define HREFV60_SDMMC_EN_GPIO		169
#define HREFV60_MMIO_XENON_CHARGE	170
#define HREFV60_PROX_SENSE_GPIO		217

/* MOP500 generic GPIOs */
#define CAMERA_FLASH_INT_PIN		7
#define CYPRESS_TOUCH_INT_PIN		84
#define XSHUTDOWN_PRIMARY_SENSOR	141
#define XSHUTDOWN_SECONDARY_SENSOR	142
#define CYPRESS_TOUCH_RST_GPIO		143
#define MOP500_HDMI_RST_GPIO		196
#define CYPRESS_SLAVE_SELECT_GPIO	216

/* GPIOs on the TC35892 expander */
#define MOP500_EGPIO(x)			(NOMADIK_NR_GPIO + (x))
#define GPIO_MAGNET_DRDY		MOP500_EGPIO(1)
#define GPIO_SDMMC_CD			MOP500_EGPIO(3)
#define GPIO_CAMERA_FLASH_ENABLE	MOP500_EGPIO(4)
#define GPIO_MMIO_XENON_CHARGE		MOP500_EGPIO(5)
#define GPIO_PROX_SENSOR		MOP500_EGPIO(7)
#define GPIO_HAL_SENSOR			MOP500_EGPIO(8)
#define GPIO_ACCEL_INT1			MOP500_EGPIO(10)
#define GPIO_ACCEL_INT2			MOP500_EGPIO(11)
#define GPIO_BU21013_CS			MOP500_EGPIO(13)
#define MOP500_DISP2_RST_GPIO		MOP500_EGPIO(14)
#define MOP500_DISP1_RST_GPIO		MOP500_EGPIO(15)
#define GPIO_SDMMC_EN			MOP500_EGPIO(17)
#define GPIO_SDMMC_1V8_3V_SEL		MOP500_EGPIO(18)
#define MOP500_EGPIO_END		MOP500_EGPIO(24)

/*
 * GPIOs on the AB8500 mixed-signals circuit
 * Notice that we subtract 1 from the number passed into the macro, this is
 * because the AB8500 GPIO pins are enumbered starting from 1, so the value in
 * parens matches the GPIO pin number in the data sheet.
 */
#define MOP500_AB8500_PIN_GPIO(x)	(MOP500_EGPIO_END + (x) - 1)
/*Snowball AB8500 GPIO */
#define SNOWBALL_VSMPS2_1V8_GPIO	MOP500_AB8500_PIN_GPIO(1)	/* SYSCLKREQ2/GPIO1 */
#define SNOWBALL_PM_GPIO1_GPIO		MOP500_AB8500_PIN_GPIO(2)	/* SYSCLKREQ3/GPIO2 */
#define SNOWBALL_WLAN_CLK_REQ_GPIO	MOP500_AB8500_PIN_GPIO(3)	/* SYSCLKREQ4/GPIO3 */
#define SNOWBALL_PM_GPIO4_GPIO		MOP500_AB8500_PIN_GPIO(4)	/* SYSCLKREQ6/GPIO4 */
#define SNOWBALL_EN_3V6_GPIO		MOP500_AB8500_PIN_GPIO(16)	/* PWMOUT3/GPIO16 */
#define SNOWBALL_PME_ETH_GPIO		MOP500_AB8500_PIN_GPIO(24)	/* SYSCLKREQ7/GPIO24 */
#define SNOWBALL_EN_3V3_ETH_GPIO	MOP500_AB8500_PIN_GPIO(26)	/* GPIO26 */

struct device;
struct i2c_board_info;
extern struct mmci_platform_data mop500_sdi0_data;
extern struct mmci_platform_data mop500_sdi1_data;
extern struct mmci_platform_data mop500_sdi2_data;
extern struct mmci_platform_data mop500_sdi4_data;
extern struct msp_i2s_platform_data msp0_platform_data;
extern struct msp_i2s_platform_data msp1_platform_data;
extern struct msp_i2s_platform_data msp2_platform_data;
extern struct msp_i2s_platform_data msp3_platform_data;
extern struct arm_pmu_platdata db8500_pmu_platdata;

extern void mop500_sdi_init(struct device *parent);
extern void snowball_sdi_init(struct device *parent);
extern void hrefv60_sdi_init(struct device *parent);
extern void mop500_sdi_tc35892_init(struct device *parent);
void __init mop500_u8500uib_init(void);
void __init mop500_stuib_init(void);
void __init mop500_pinmaps_init(void);
void __init snowball_pinmaps_init(void);
void __init hrefv60_pinmaps_init(void);
void mop500_audio_init(struct device *parent);
/* Due for removal once the MSP driver has been fully DT:ed. */
void mop500_of_audio_init(struct device *parent);

int __init mop500_uib_init(void);
void mop500_uib_i2c_add(int busnum, struct i2c_board_info *info,
		unsigned n);

/* TODO: Once all pieces are DT:ed, remove completely. */
struct device * __init u8500_of_init_devices(void);

#endif