sound/oss/Kconfig - kernel/msm-4.9 - Gitiles

 # drivers/sound/Config.in
 #
 # 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
 # More hacking for modularisation.
 #
 # Prompt user for primary drivers.

 config SOUND_BCM_CS4297A
 	tristate "Crystal Sound CS4297a (for Swarm)"
 	depends on SIBYTE_SWARM
 	help
 	  The BCM91250A has a Crystal CS4297a on synchronous serial
 	  port B (in addition to the DB-9 serial port).  Say Y or M
 	  here to enable the sound chip instead of the UART.  Also
 	  note that CONFIG_KGDB should not be enabled at the same
 	  time, since it also attempts to use this UART port.

 config SOUND_VWSND
 	tristate "SGI Visual Workstation Sound"
 	depends on X86_VISWS
 	help
 	  Say Y or M if you have an SGI Visual Workstation and you want to be
 	  able to use its on-board audio.  Read
 	  <file:Documentation/sound/oss/vwsnd> for more info on this driver's
 	  capabilities.

 config SOUND_AU1550_AC97
 	tristate "Au1550/Au1200 AC97 Sound"
 	depends on SOC_AU1550 || SOC_AU1200

 config SOUND_MSNDCLAS
 	tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
 	depends on (m || !STANDALONE) && ISA
 	help
 	  Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
 	  Monterey (not for the Pinnacle or Fiji).

 	  See <file:Documentation/sound/oss/MultiSound> for important information
 	  about this driver.  Note that it has been discontinued, but the
 	  Voyetra Turtle Beach knowledge base entry for it is still available
 	  at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.

 comment "Compiled-in MSND Classic support requires firmware during compilation."
 	depends on SOUND_PRIME && SOUND_MSNDCLAS=y

 config MSNDCLAS_HAVE_BOOT
 	bool
 	depends on SOUND_MSNDCLAS=y && !STANDALONE
 	default y

 config MSNDCLAS_INIT_FILE
 	string "Full pathname of MSNDINIT.BIN firmware file"
 	depends on SOUND_MSNDCLAS
 	default "/etc/sound/msndinit.bin"
 	help
 	  The MultiSound cards have two firmware files which are required for
 	  operation, and are not currently included. These files can be
 	  obtained from Turtle Beach. See
 	  <file:Documentation/sound/oss/MultiSound> for information on how to
 	  obtain this.

 config MSNDCLAS_PERM_FILE
 	string "Full pathname of MSNDPERM.BIN firmware file"
 	depends on SOUND_MSNDCLAS
 	default "/etc/sound/msndperm.bin"
 	help
 	  The MultiSound cards have two firmware files which are required for
 	  operation, and are not currently included. These files can be
 	  obtained from Turtle Beach. See
 	  <file:Documentation/sound/oss/MultiSound> for information on how to
 	  obtain this.

 config MSNDCLAS_IRQ
 	int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
 	depends on SOUND_MSNDCLAS=y
 	default "5"
 	help
 	  Interrupt Request line for the MultiSound Classic and related cards.

 config MSNDCLAS_MEM
 	hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
 	depends on SOUND_MSNDCLAS=y
 	default "D0000"
 	help
 	  Memory-mapped I/O base address for the MultiSound Classic and
 	  related cards.

 config MSNDCLAS_IO
 	hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
 	depends on SOUND_MSNDCLAS=y
 	default "290"
 	help
 	  I/O port address for the MultiSound Classic and related cards.

 config SOUND_MSNDPIN
 	tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
 	depends on (m || !STANDALONE) && ISA
 	help
 	  Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
 	  See <file:Documentation/sound/oss/MultiSound> for important information
 	  about this driver. Note that it has been discontinued, but the
 	  Voyetra Turtle Beach knowledge base entry for it is still available
 	  at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.

 comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
 	depends on SOUND_PRIME && SOUND_MSNDPIN=y

 config MSNDPIN_HAVE_BOOT
 	bool
 	depends on SOUND_MSNDPIN=y
 	default y

 config MSNDPIN_INIT_FILE
 	string "Full pathname of PNDSPINI.BIN firmware file"
 	depends on SOUND_MSNDPIN
 	default "/etc/sound/pndspini.bin"
 	help
 	  The MultiSound cards have two firmware files which are required
 	  for operation, and are not currently included. These files can be
 	  obtained from Turtle Beach. See
 	  <file:Documentation/sound/oss/MultiSound> for information on how to
 	  obtain this.

 config MSNDPIN_PERM_FILE
 	string "Full pathname of PNDSPERM.BIN firmware file"
 	depends on SOUND_MSNDPIN
 	default "/etc/sound/pndsperm.bin"
 	help
 	  The MultiSound cards have two firmware files which are required for
 	  operation, and are not currently included. These files can be
 	  obtained from Turtle Beach. See
 	  <file:Documentation/sound/oss/MultiSound> for information on how to
 	  obtain this.

 config MSNDPIN_IRQ
 	int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
 	depends on SOUND_MSNDPIN=y
 	default "5"
 	help
 	  Interrupt request line for the primary synthesizer on MultiSound
 	  Pinnacle and Fiji sound cards.

 config MSNDPIN_MEM
 	hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
 	depends on SOUND_MSNDPIN=y
 	default "D0000"
 	help
 	  Memory-mapped I/O base address for the primary synthesizer on
 	  MultiSound Pinnacle and Fiji sound cards.

 config MSNDPIN_IO
 	hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
 	depends on SOUND_MSNDPIN=y
 	default "290"
 	help
 	  Memory-mapped I/O base address for the primary synthesizer on
 	  MultiSound Pinnacle and Fiji sound cards.

 config MSNDPIN_DIGITAL
 	bool "MSND Pinnacle has S/PDIF I/O"
 	depends on SOUND_MSNDPIN=y
 	help
 	  If you have the S/PDIF daughter board for the Pinnacle or Fiji,
 	  answer Y here; otherwise, say N. If you have this, you will be able
 	  to play and record from the S/PDIF port (digital signal). See
 	  <file:Documentation/sound/oss/MultiSound> for information on how to make
 	  use of this capability.

 config MSNDPIN_NONPNP
 	bool "MSND Pinnacle non-PnP Mode"
 	depends on SOUND_MSNDPIN=y
 	help
 	  The Pinnacle and Fiji card resources can be configured either with
 	  PnP, or through a configuration port. Say Y here if your card is NOT
 	  in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
 	  use of the IDE and joystick peripherals on the card as well; these
 	  do not show up when the card is in PnP mode. Specifying zero for any
 	  resource of a device will disable the device. If you are running the
 	  card in PnP mode, you must say N here and use isapnptools to
 	  configure the card's resources.

 comment "MSND Pinnacle DSP section will be configured to above parameters."
 	depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP

 config MSNDPIN_CFG
 	hex "MSND Pinnacle config port 250,260,270"
 	depends on MSNDPIN_NONPNP
 	default "250"
 	help
 	  This is the port which the Pinnacle and Fiji uses to configure the
 	  card's resources when not in PnP mode. If your card is in PnP mode,
 	  then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
 	  Mode".

 comment "Pinnacle-specific Device Configuration (0 disables)"
 	depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP

 config MSNDPIN_MPU_IO
 	hex "MSND Pinnacle MPU I/O (e.g. 330)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  Memory-mapped I/O base address for the Kurzweil daughterboard
 	  synthesizer on MultiSound Pinnacle and Fiji sound cards.

 config MSNDPIN_MPU_IRQ
 	int "MSND Pinnacle MPU IRQ (e.g. 9)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  Interrupt request number for the Kurzweil daughterboard
 	  synthesizer on MultiSound Pinnacle and Fiji sound cards.

 config MSNDPIN_IDE_IO0
 	hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
 	  Pinnacle and Fiji sound cards.

 config MSNDPIN_IDE_IO1
 	hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
 	  Pinnacle and Fiji sound cards.

 config MSNDPIN_IDE_IRQ
 	int "MSND Pinnacle IDE IRQ (e.g. 15)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  Interrupt request number for the IDE CD-ROM interface on the
 	  MultiSound Pinnacle and Fiji sound cards.

 config MSNDPIN_JOYSTICK_IO
 	hex "MSND Pinnacle joystick I/O (e.g. 200)"
 	depends on MSNDPIN_NONPNP
 	default "0"
 	help
 	  Memory-mapped I/O base address for the joystick port on MultiSound
 	  Pinnacle and Fiji sound cards.

 config MSND_FIFOSIZE
 	int "MSND buffer size (kB)"
 	depends on SOUND_MSNDPIN=y || SOUND_MSNDCLAS=y
 	default "128"
 	help
 	  Configures the size of each audio buffer, in kilobytes, for
 	  recording and playing in the MultiSound drivers (both the Classic
 	  and Pinnacle). Larger values reduce the chance of data overruns at
 	  the expense of overall latency. If unsure, use the default.

 menuconfig SOUND_OSS
 	tristate "OSS sound modules"
 	depends on ISA_DMA_API && VIRT_TO_BUS
 	help
 	  OSS is the Open Sound System suite of sound card drivers.  They make
 	  sound programming easier since they provide a common API.  Say Y or
 	  M here (the module will be called sound) if you haven't found a
 	  driver for your sound card above, then pick your driver from the
 	  list below.

 if SOUND_OSS

 config SOUND_TRACEINIT
 	bool "Verbose initialisation"
 	help
 	  Verbose soundcard initialization -- affects the format of autoprobe
 	  and initialization messages at boot time.

 config SOUND_DMAP
 	bool "Persistent DMA buffers"
 	---help---
 	  Linux can often have problems allocating DMA buffers for ISA sound
 	  cards on machines with more than 16MB of RAM. This is because ISA
 	  DMA buffers must exist below the 16MB boundary and it is quite
 	  possible that a large enough free block in this region cannot be
 	  found after the machine has been running for a while. If you say Y
 	  here the DMA buffers (64Kb) will be allocated at boot time and kept
 	  until the shutdown. This option is only useful if you said Y to
 	  "OSS sound modules", above. If you said M to "OSS sound modules"
 	  then you can get the persistent DMA buffer functionality by passing
 	  the command-line argument "dmabuf=1" to the sound module.

 	  Say Y unless you have 16MB or more RAM or a PCI sound card.

 config SOUND_VMIDI
 	tristate "Loopback MIDI device support"
 	help
 	  Support for MIDI loopback on port 1 or 2.

 config SOUND_TRIX
 	tristate "MediaTrix AudioTrix Pro support"
 	help
 	  Answer Y if you have the AudioTriX Pro sound card manufactured
 	  by MediaTrix.

 config TRIX_HAVE_BOOT
 	bool "Have TRXPRO.HEX firmware file"
 	depends on SOUND_TRIX=y && !STANDALONE
 	help
 	  The MediaTrix AudioTrix Pro has an on-board microcontroller which
 	  needs to be initialized by downloading the code from the file
 	  TRXPRO.HEX in the DOS driver directory. If you don't have the
 	  TRXPRO.HEX file handy you may skip this step. However, the SB and
 	  MPU-401 modes of AudioTrix Pro will not work without this file!

 config TRIX_BOOT_FILE
 	string "Full pathname of TRXPRO.HEX firmware file"
 	depends on TRIX_HAVE_BOOT
 	default "/etc/sound/trxpro.hex"
 	help
 	  Enter the full pathname of your TRXPRO.HEX file, starting from /.

 config SOUND_MSS
 	tristate "Microsoft Sound System support"
 	---help---
 	  Again think carefully before answering Y to this question.  It's
 	  safe to answer Y if you have the original Windows Sound System card
 	  made by Microsoft or Aztech SG 16 Pro (or NX16 Pro).  Also you may
 	  say Y in case your card is NOT among these:

 	  ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
 	  Ensoniq SoundScape (and compatibles made by Reveal and Spea),
 	  Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
 	  Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
 	  Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
 	  82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
 	  Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
 	  SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
 	  Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
 	  Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
 	  Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
 	  notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
 	  synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.

 	  For cards having native support in VoxWare, consult the card
 	  specific instructions in <file:Documentation/sound/oss/README.OSS>.
 	  Some drivers have their own MSS support and saying Y to this option
 	  will cause a conflict.

 	  If you compile the driver into the kernel, you have to add
 	  "ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
 	  line.

 config SOUND_MPU401
 	tristate "MPU-401 support (NOT for SB16)"
 	---help---
 	  Be careful with this question.  The MPU401 interface is supported by
 	  all sound cards.  However, some natively supported cards have their
 	  own driver for MPU401.  Enabling this MPU401 option with these cards
 	  will cause a conflict.  Also, enabling MPU401 on a system that
 	  doesn't really have a MPU401 could cause some trouble.  If your card
 	  was in the list of supported cards, look at the card specific
 	  instructions in the <file:Documentation/sound/oss/README.OSS> file.  It
 	  is safe to answer Y if you have a true MPU401 MIDI interface card.

 	  If you compile the driver into the kernel, you have to add
 	  "mpu401=<io>,<irq>" to the kernel command line.

 config SOUND_PAS
 	tristate "ProAudioSpectrum 16 support"
 	---help---
 	  Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
 	  16 or Logitech SoundMan 16 sound card. Answer N if you have some
 	  other card made by Media Vision or Logitech since those are not
 	  PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
 	  It is not necessary to add Sound Blaster support separately; it
 	  is included in PAS support.

 	  If you compile the driver into the kernel, you have to add
 	  "pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
 	  to the kernel command line.

 config PAS_JOYSTICK
 	bool "Enable PAS16 joystick port"
 	depends on SOUND_PAS=y
 	help
 	  Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
 	  port.

 config SOUND_PSS
 	tristate "PSS (AD1848, ADSP-2115, ESC614) support"
 	help
 	  Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
 	  ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
 	  ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
 	  how to compile it into the kernel or as a module see the file
 	  <file:Documentation/sound/oss/PSS>.

 	  If you compile the driver into the kernel, you have to add
 	  "pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
 	  command line.

 config PSS_MIXER
 	bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
 	depends on SOUND_PSS
 	help
 	  Answer Y for Beethoven ADSP-16. You may try to say Y also for other
 	  cards if they have master volume, bass, treble, and you can't
 	  control it under Linux. If you answer N for Beethoven ADSP-16, you
 	  can't control master volume, bass, treble and synth volume.

 	  If you said M to "PSS support" above, you may enable or disable this
 	  PSS mixer with the module parameter pss_mixer. For more information
 	  see the file <file:Documentation/sound/oss/PSS>.

 config PSS_HAVE_BOOT
 	bool "Have DSPxxx.LD firmware file"
 	depends on SOUND_PSS && !STANDALONE
 	help
 	  If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
 	  to include this file. Without this file the synth device (OPL) may
 	  not work.

 config PSS_BOOT_FILE
 	string "Full pathname of DSPxxx.LD firmware file"
 	depends on PSS_HAVE_BOOT
 	default "/etc/sound/dsp001.ld"
 	help
 	  Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
 	  starting from /.

 config SOUND_SB
 	tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
 	---help---
 	  Answer Y if you have an original Sound Blaster card made by Creative
 	  Labs or a 100% hardware compatible clone (like the Thunderboard or
 	  SM Games). For an unknown card you may answer Y if the card claims
 	  to be Sound Blaster-compatible.

 	  Please read the file <file:Documentation/sound/oss/Soundblaster>.

 	  You should also say Y here for cards based on the Avance Logic
 	  ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
 	  for cards based on ESS chips (read
 	  <file:Documentation/sound/oss/ESS1868> and
 	  <file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE
 	  64, say Y here and also to "AWE32 synth" below and read
 	  <file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave
 	  card, say Y here and read <file:Documentation/sound/oss/mwave>.

 	  If you compile the driver into the kernel and don't want to use
 	  isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
 	  command line.

 	  You can say M here to compile this driver as a module; the module is
 	  called sb.

 config SOUND_YM3812
 	tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
 	---help---
 	  Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
 	  Answering Y is usually a safe and recommended choice, however some
 	  cards may have software (TSR) FM emulation. Enabling FM support with
 	  these cards may cause trouble (I don't currently know of any such
 	  cards, however). Please read the file
 	  <file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.

 	  If you compile the driver into the kernel, you have to add
 	  "opl3=<io>" to the kernel command line.

 	  If unsure, say Y.

 config SOUND_UART6850
 	tristate "6850 UART support"
 	help
 	  This option enables support for MIDI interfaces based on the 6850
 	  UART chip. This interface is rarely found on sound cards. It's safe
 	  to answer N to this question.

 	  If you compile the driver into the kernel, you have to add
 	  "uart6850=<io>,<irq>" to the kernel command line.

 config SOUND_AEDSP16
 	tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
 	---help---
 	  Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
 	  driver supports Audio Excel DSP 16 but not the III nor PnP versions
 	  of this card.

 	  The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
 	  a Microsoft Sound System card, so you should have said Y to either
 	  "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
 	  or "Microsoft Sound System support", above, and you need to answer
 	  the "MSS emulation" and "SBPro emulation" questions below
 	  accordingly. You should say Y to one and only one of these two
 	  questions.

 	  Read the <file:Documentation/sound/oss/README.OSS> file and the head of
 	  <file:sound/oss/aedsp16.c> as well as
 	  <file:Documentation/sound/oss/AudioExcelDSP16> to get more information
 	  about this driver and its configuration.

 config SC6600
 	bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
 	depends on SOUND_AEDSP16
 	help
 	  The SC6600 is the new version of DSP mounted on the Audio Excel DSP
 	  16 cards. Find in the manual the FCC ID of your audio card and
 	  answer Y if you have an SC6600 DSP.

 config SC6600_JOY
 	bool "Activate SC-6600 Joystick Interface"
 	depends on SC6600
 	help
 	  Say Y here in order to use the joystick interface of the Audio Excel
 	  DSP 16 card.

 config SC6600_CDROM
 	int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
 	depends on SC6600
 	default "4"
 	help
 	  This is used to activate the CD-ROM interface of the Audio Excel
 	  DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
 	  CD-ROM present.

 config SC6600_CDROMBASE
 	hex "SC-6600 CDROM Interface I/O Address"
 	depends on SC6600
 	default "0"
 	help
 	  Base I/O port address for the CD-ROM interface of the Audio Excel
 	  DSP 16 card.

 config SOUND_VIDC
 	tristate "VIDC 16-bit sound"
 	depends on ARM && (ARCH_ACORN || ARCH_CLPS7500)
 	help
 	  16-bit support for the VIDC onboard sound hardware found on Acorn
 	  machines.

 config SOUND_WAVEARTIST
 	tristate "Netwinder WaveArtist"
 	depends on ARM && ARCH_NETWINDER
 	help
 	  Say Y here to include support for the Rockwell WaveArtist sound
 	  system.  This driver is mainly for the NetWinder.

 config SOUND_KAHLUA
 	tristate "XpressAudio Sound Blaster emulation"
 	depends on SOUND_SB

 endif	# SOUND_OSS

 config SOUND_SH_DAC_AUDIO
 	tristate "SuperH DAC audio support"
 	depends on CPU_SH3 && HIGH_RES_TIMERS

 config SOUND_SH_DAC_AUDIO_CHANNEL
 	int "DAC channel"
 	default "1"
 	depends on SOUND_SH_DAC_AUDIO
	# drivers/sound/Config.in
	#
	# 18 Apr 1998, Michael Elizabeth Chastain, <mailto:mec@shout.net>
	# More hacking for modularisation.
	#
	# Prompt user for primary drivers.

	config SOUND_BCM_CS4297A
	tristate "Crystal Sound CS4297a (for Swarm)"
	depends on SIBYTE_SWARM
	help
	The BCM91250A has a Crystal CS4297a on synchronous serial
	port B (in addition to the DB-9 serial port). Say Y or M
	here to enable the sound chip instead of the UART. Also
	note that CONFIG_KGDB should not be enabled at the same
	time, since it also attempts to use this UART port.

	config SOUND_VWSND
	tristate "SGI Visual Workstation Sound"
	depends on X86_VISWS
	help
	Say Y or M if you have an SGI Visual Workstation and you want to be
	able to use its on-board audio. Read
	<file:Documentation/sound/oss/vwsnd> for more info on this driver's
	capabilities.

	config SOUND_AU1550_AC97
	tristate "Au1550/Au1200 AC97 Sound"
	depends on SOC_AU1550 \|\| SOC_AU1200

	config SOUND_MSNDCLAS
	tristate "Support for Turtle Beach MultiSound Classic, Tahiti, Monterey"
	depends on (m \|\| !STANDALONE) && ISA
	help
	Say M here if you have a Turtle Beach MultiSound Classic, Tahiti or
	Monterey (not for the Pinnacle or Fiji).

	See <file:Documentation/sound/oss/MultiSound> for important information
	about this driver. Note that it has been discontinued, but the
	Voyetra Turtle Beach knowledge base entry for it is still available
	at <http://www.turtlebeach.com/site/kb_ftp/790.asp>.

	comment "Compiled-in MSND Classic support requires firmware during compilation."
	depends on SOUND_PRIME && SOUND_MSNDCLAS=y

	config MSNDCLAS_HAVE_BOOT
	bool
	depends on SOUND_MSNDCLAS=y && !STANDALONE
	default y

	config MSNDCLAS_INIT_FILE
	string "Full pathname of MSNDINIT.BIN firmware file"
	depends on SOUND_MSNDCLAS
	default "/etc/sound/msndinit.bin"
	help
	The MultiSound cards have two firmware files which are required for
	operation, and are not currently included. These files can be
	obtained from Turtle Beach. See
	<file:Documentation/sound/oss/MultiSound> for information on how to
	obtain this.

	config MSNDCLAS_PERM_FILE
	string "Full pathname of MSNDPERM.BIN firmware file"
	depends on SOUND_MSNDCLAS
	default "/etc/sound/msndperm.bin"
	help
	The MultiSound cards have two firmware files which are required for
	operation, and are not currently included. These files can be
	obtained from Turtle Beach. See
	<file:Documentation/sound/oss/MultiSound> for information on how to
	obtain this.

	config MSNDCLAS_IRQ
	int "MSND Classic IRQ 5, 7, 9, 10, 11, 12"
	depends on SOUND_MSNDCLAS=y
	default "5"
	help
	Interrupt Request line for the MultiSound Classic and related cards.

	config MSNDCLAS_MEM
	hex "MSND Classic memory B0000, C8000, D0000, D8000, E0000, E8000"
	depends on SOUND_MSNDCLAS=y
	default "D0000"
	help
	Memory-mapped I/O base address for the MultiSound Classic and
	related cards.

	config MSNDCLAS_IO
	hex "MSND Classic I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
	depends on SOUND_MSNDCLAS=y
	default "290"
	help
	I/O port address for the MultiSound Classic and related cards.

	config SOUND_MSNDPIN
	tristate "Support for Turtle Beach MultiSound Pinnacle, Fiji"
	depends on (m \|\| !STANDALONE) && ISA
	help
	Say M here if you have a Turtle Beach MultiSound Pinnacle or Fiji.
	See <file:Documentation/sound/oss/MultiSound> for important information
	about this driver. Note that it has been discontinued, but the
	Voyetra Turtle Beach knowledge base entry for it is still available
	at <http://www.turtlebeach.com/site/kb_ftp/600.asp>.

	comment "Compiled-in MSND Pinnacle support requires firmware during compilation."
	depends on SOUND_PRIME && SOUND_MSNDPIN=y

	config MSNDPIN_HAVE_BOOT
	bool
	depends on SOUND_MSNDPIN=y
	default y

	config MSNDPIN_INIT_FILE
	string "Full pathname of PNDSPINI.BIN firmware file"
	depends on SOUND_MSNDPIN
	default "/etc/sound/pndspini.bin"
	help
	The MultiSound cards have two firmware files which are required
	for operation, and are not currently included. These files can be
	obtained from Turtle Beach. See
	<file:Documentation/sound/oss/MultiSound> for information on how to
	obtain this.

	config MSNDPIN_PERM_FILE
	string "Full pathname of PNDSPERM.BIN firmware file"
	depends on SOUND_MSNDPIN
	default "/etc/sound/pndsperm.bin"
	help
	The MultiSound cards have two firmware files which are required for
	operation, and are not currently included. These files can be
	obtained from Turtle Beach. See
	<file:Documentation/sound/oss/MultiSound> for information on how to
	obtain this.

	config MSNDPIN_IRQ
	int "MSND Pinnacle IRQ 5, 7, 9, 10, 11, 12"
	depends on SOUND_MSNDPIN=y
	default "5"
	help
	Interrupt request line for the primary synthesizer on MultiSound
	Pinnacle and Fiji sound cards.

	config MSNDPIN_MEM
	hex "MSND Pinnacle memory B0000, C8000, D0000, D8000, E0000, E8000"
	depends on SOUND_MSNDPIN=y
	default "D0000"
	help
	Memory-mapped I/O base address for the primary synthesizer on
	MultiSound Pinnacle and Fiji sound cards.

	config MSNDPIN_IO
	hex "MSND Pinnacle I/O 210, 220, 230, 240, 250, 260, 290, 3E0"
	depends on SOUND_MSNDPIN=y
	default "290"
	help
	Memory-mapped I/O base address for the primary synthesizer on
	MultiSound Pinnacle and Fiji sound cards.

	config MSNDPIN_DIGITAL
	bool "MSND Pinnacle has S/PDIF I/O"
	depends on SOUND_MSNDPIN=y
	help
	If you have the S/PDIF daughter board for the Pinnacle or Fiji,
	answer Y here; otherwise, say N. If you have this, you will be able
	to play and record from the S/PDIF port (digital signal). See
	<file:Documentation/sound/oss/MultiSound> for information on how to make
	use of this capability.

	config MSNDPIN_NONPNP
	bool "MSND Pinnacle non-PnP Mode"
	depends on SOUND_MSNDPIN=y
	help
	The Pinnacle and Fiji card resources can be configured either with
	PnP, or through a configuration port. Say Y here if your card is NOT
	in PnP mode. For the Pinnacle, configuration in non-PnP mode allows
	use of the IDE and joystick peripherals on the card as well; these
	do not show up when the card is in PnP mode. Specifying zero for any
	resource of a device will disable the device. If you are running the
	card in PnP mode, you must say N here and use isapnptools to
	configure the card's resources.

	comment "MSND Pinnacle DSP section will be configured to above parameters."
	depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP

	config MSNDPIN_CFG
	hex "MSND Pinnacle config port 250,260,270"
	depends on MSNDPIN_NONPNP
	default "250"
	help
	This is the port which the Pinnacle and Fiji uses to configure the
	card's resources when not in PnP mode. If your card is in PnP mode,
	then be sure to say N to the previous option, "MSND Pinnacle Non-PnP
	Mode".

	comment "Pinnacle-specific Device Configuration (0 disables)"
	depends on SOUND_MSNDPIN=y && MSNDPIN_NONPNP

	config MSNDPIN_MPU_IO
	hex "MSND Pinnacle MPU I/O (e.g. 330)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	Memory-mapped I/O base address for the Kurzweil daughterboard
	synthesizer on MultiSound Pinnacle and Fiji sound cards.

	config MSNDPIN_MPU_IRQ
	int "MSND Pinnacle MPU IRQ (e.g. 9)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	Interrupt request number for the Kurzweil daughterboard
	synthesizer on MultiSound Pinnacle and Fiji sound cards.

	config MSNDPIN_IDE_IO0
	hex "MSND Pinnacle IDE I/O 0 (e.g. 170)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	CD-ROM drive 0 memory-mapped I/O base address for the MultiSound
	Pinnacle and Fiji sound cards.

	config MSNDPIN_IDE_IO1
	hex "MSND Pinnacle IDE I/O 1 (e.g. 376)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	CD-ROM drive 1 memory-mapped I/O base address for the MultiSound
	Pinnacle and Fiji sound cards.

	config MSNDPIN_IDE_IRQ
	int "MSND Pinnacle IDE IRQ (e.g. 15)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	Interrupt request number for the IDE CD-ROM interface on the
	MultiSound Pinnacle and Fiji sound cards.

	config MSNDPIN_JOYSTICK_IO
	hex "MSND Pinnacle joystick I/O (e.g. 200)"
	depends on MSNDPIN_NONPNP
	default "0"
	help
	Memory-mapped I/O base address for the joystick port on MultiSound
	Pinnacle and Fiji sound cards.

	config MSND_FIFOSIZE
	int "MSND buffer size (kB)"
	depends on SOUND_MSNDPIN=y \|\| SOUND_MSNDCLAS=y
	default "128"
	help
	Configures the size of each audio buffer, in kilobytes, for
	recording and playing in the MultiSound drivers (both the Classic
	and Pinnacle). Larger values reduce the chance of data overruns at
	the expense of overall latency. If unsure, use the default.

	menuconfig SOUND_OSS
	tristate "OSS sound modules"
	depends on ISA_DMA_API && VIRT_TO_BUS
	help
	OSS is the Open Sound System suite of sound card drivers. They make
	sound programming easier since they provide a common API. Say Y or
	M here (the module will be called sound) if you haven't found a
	driver for your sound card above, then pick your driver from the
	list below.

	if SOUND_OSS

	config SOUND_TRACEINIT
	bool "Verbose initialisation"
	help
	Verbose soundcard initialization -- affects the format of autoprobe
	and initialization messages at boot time.

	config SOUND_DMAP
	bool "Persistent DMA buffers"
	---help---
	Linux can often have problems allocating DMA buffers for ISA sound
	cards on machines with more than 16MB of RAM. This is because ISA
	DMA buffers must exist below the 16MB boundary and it is quite
	possible that a large enough free block in this region cannot be
	found after the machine has been running for a while. If you say Y
	here the DMA buffers (64Kb) will be allocated at boot time and kept
	until the shutdown. This option is only useful if you said Y to
	"OSS sound modules", above. If you said M to "OSS sound modules"
	then you can get the persistent DMA buffer functionality by passing
	the command-line argument "dmabuf=1" to the sound module.

	Say Y unless you have 16MB or more RAM or a PCI sound card.

	config SOUND_VMIDI
	tristate "Loopback MIDI device support"
	help
	Support for MIDI loopback on port 1 or 2.

	config SOUND_TRIX
	tristate "MediaTrix AudioTrix Pro support"
	help
	Answer Y if you have the AudioTriX Pro sound card manufactured
	by MediaTrix.

	config TRIX_HAVE_BOOT
	bool "Have TRXPRO.HEX firmware file"
	depends on SOUND_TRIX=y && !STANDALONE
	help
	The MediaTrix AudioTrix Pro has an on-board microcontroller which
	needs to be initialized by downloading the code from the file
	TRXPRO.HEX in the DOS driver directory. If you don't have the
	TRXPRO.HEX file handy you may skip this step. However, the SB and
	MPU-401 modes of AudioTrix Pro will not work without this file!

	config TRIX_BOOT_FILE
	string "Full pathname of TRXPRO.HEX firmware file"
	depends on TRIX_HAVE_BOOT
	default "/etc/sound/trxpro.hex"
	help
	Enter the full pathname of your TRXPRO.HEX file, starting from /.

	config SOUND_MSS
	tristate "Microsoft Sound System support"
	---help---
	Again think carefully before answering Y to this question. It's
	safe to answer Y if you have the original Windows Sound System card
	made by Microsoft or Aztech SG 16 Pro (or NX16 Pro). Also you may
	say Y in case your card is NOT among these:

	ATI Stereo F/X, AdLib, Audio Excell DSP16, Cardinal DSP16,
	Ensoniq SoundScape (and compatibles made by Reveal and Spea),
	Gravis Ultrasound, Gravis Ultrasound ACE, Gravis Ultrasound Max,
	Gravis Ultrasound with 16 bit option, Logitech Sound Man 16,
	Logitech SoundMan Games, Logitech SoundMan Wave, MAD16 Pro (OPTi
	82C929), Media Vision Jazz16, MediaTriX AudioTriX Pro, Microsoft
	Windows Sound System (MSS/WSS), Mozart (OAK OTI-601), Orchid
	SW32, Personal Sound System (PSS), Pro Audio Spectrum 16, Pro
	Audio Studio 16, Pro Sonic 16, Roland MPU-401 MIDI interface,
	Sound Blaster 1.0, Sound Blaster 16, Sound Blaster 16ASP, Sound
	Blaster 2.0, Sound Blaster AWE32, Sound Blaster Pro, TI TM4000M
	notebook, ThunderBoard, Turtle Beach Tropez, Yamaha FM
	synthesizers (OPL2, OPL3 and OPL4), 6850 UART MIDI Interface.

	For cards having native support in VoxWare, consult the card
	specific instructions in <file:Documentation/sound/oss/README.OSS>.
	Some drivers have their own MSS support and saying Y to this option
	will cause a conflict.

	If you compile the driver into the kernel, you have to add
	"ad1848=<io>,<irq>,<dma>,<dma2>[,<type>]" to the kernel command
	line.

	config SOUND_MPU401
	tristate "MPU-401 support (NOT for SB16)"
	---help---
	Be careful with this question. The MPU401 interface is supported by
	all sound cards. However, some natively supported cards have their
	own driver for MPU401. Enabling this MPU401 option with these cards
	will cause a conflict. Also, enabling MPU401 on a system that
	doesn't really have a MPU401 could cause some trouble. If your card
	was in the list of supported cards, look at the card specific
	instructions in the <file:Documentation/sound/oss/README.OSS> file. It
	is safe to answer Y if you have a true MPU401 MIDI interface card.

	If you compile the driver into the kernel, you have to add
	"mpu401=<io>,<irq>" to the kernel command line.

	config SOUND_PAS
	tristate "ProAudioSpectrum 16 support"
	---help---
	Answer Y only if you have a Pro Audio Spectrum 16, ProAudio Studio
	16 or Logitech SoundMan 16 sound card. Answer N if you have some
	other card made by Media Vision or Logitech since those are not
	PAS16 compatible. Please read <file:Documentation/sound/oss/PAS16>.
	It is not necessary to add Sound Blaster support separately; it
	is included in PAS support.

	If you compile the driver into the kernel, you have to add
	"pas2=<io>,<irq>,<dma>,<dma2>,<sbio>,<sbirq>,<sbdma>,<sbdma2>
	to the kernel command line.

	config PAS_JOYSTICK
	bool "Enable PAS16 joystick port"
	depends on SOUND_PAS=y
	help
	Say Y here to enable the Pro Audio Spectrum 16's auxiliary joystick
	port.

	config SOUND_PSS
	tristate "PSS (AD1848, ADSP-2115, ESC614) support"
	help
	Answer Y or M if you have an Orchid SW32, Cardinal DSP16, Beethoven
	ADSP-16 or some other card based on the PSS chipset (AD1848 codec +
	ADSP-2115 DSP chip + Echo ESC614 ASIC CHIP). For more information on
	how to compile it into the kernel or as a module see the file
	<file:Documentation/sound/oss/PSS>.

	If you compile the driver into the kernel, you have to add
	"pss=<io>,<mssio>,<mssirq>,<mssdma>,<mpuio>,<mpuirq>" to the kernel
	command line.

	config PSS_MIXER
	bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
	depends on SOUND_PSS
	help
	Answer Y for Beethoven ADSP-16. You may try to say Y also for other
	cards if they have master volume, bass, treble, and you can't
	control it under Linux. If you answer N for Beethoven ADSP-16, you
	can't control master volume, bass, treble and synth volume.

	If you said M to "PSS support" above, you may enable or disable this
	PSS mixer with the module parameter pss_mixer. For more information
	see the file <file:Documentation/sound/oss/PSS>.

	config PSS_HAVE_BOOT
	bool "Have DSPxxx.LD firmware file"
	depends on SOUND_PSS && !STANDALONE
	help
	If you have the DSPxxx.LD file or SYNTH.LD file for you card, say Y
	to include this file. Without this file the synth device (OPL) may
	not work.

	config PSS_BOOT_FILE
	string "Full pathname of DSPxxx.LD firmware file"
	depends on PSS_HAVE_BOOT
	default "/etc/sound/dsp001.ld"
	help
	Enter the full pathname of your DSPxxx.LD file or SYNTH.LD file,
	starting from /.

	config SOUND_SB
	tristate "100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
	---help---
	Answer Y if you have an original Sound Blaster card made by Creative
	Labs or a 100% hardware compatible clone (like the Thunderboard or
	SM Games). For an unknown card you may answer Y if the card claims
	to be Sound Blaster-compatible.

	Please read the file <file:Documentation/sound/oss/Soundblaster>.

	You should also say Y here for cards based on the Avance Logic
	ALS-007 and ALS-1X0 chips (read <file:Documentation/sound/oss/ALS>) and
	for cards based on ESS chips (read
	<file:Documentation/sound/oss/ESS1868> and
	<file:Documentation/sound/oss/ESS>). If you have an SB AWE 32 or SB AWE
	64, say Y here and also to "AWE32 synth" below and read
	<file:Documentation/sound/oss/INSTALL.awe>. If you have an IBM Mwave
	card, say Y here and read <file:Documentation/sound/oss/mwave>.

	If you compile the driver into the kernel and don't want to use
	isapnp, you have to add "sb=<io>,<irq>,<dma>,<dma2>" to the kernel
	command line.

	You can say M here to compile this driver as a module; the module is
	called sb.

	config SOUND_YM3812
	tristate "Yamaha FM synthesizer (YM3812/OPL-3) support"
	---help---
	Answer Y if your card has a FM chip made by Yamaha (OPL2/OPL3/OPL4).
	Answering Y is usually a safe and recommended choice, however some
	cards may have software (TSR) FM emulation. Enabling FM support with
	these cards may cause trouble (I don't currently know of any such
	cards, however). Please read the file
	<file:Documentation/sound/oss/OPL3> if your card has an OPL3 chip.

	If you compile the driver into the kernel, you have to add
	"opl3=<io>" to the kernel command line.

	If unsure, say Y.

	config SOUND_UART6850
	tristate "6850 UART support"
	help
	This option enables support for MIDI interfaces based on the 6850
	UART chip. This interface is rarely found on sound cards. It's safe
	to answer N to this question.

	If you compile the driver into the kernel, you have to add
	"uart6850=<io>,<irq>" to the kernel command line.

	config SOUND_AEDSP16
	tristate "Gallant Audio Cards (SC-6000 and SC-6600 based)"
	---help---
	Answer Y if you have a Gallant's Audio Excel DSP 16 card. This
	driver supports Audio Excel DSP 16 but not the III nor PnP versions
	of this card.

	The Gallant's Audio Excel DSP 16 card can emulate either an SBPro or
	a Microsoft Sound System card, so you should have said Y to either
	"100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support"
	or "Microsoft Sound System support", above, and you need to answer
	the "MSS emulation" and "SBPro emulation" questions below
	accordingly. You should say Y to one and only one of these two
	questions.

	Read the <file:Documentation/sound/oss/README.OSS> file and the head of
	<file:sound/oss/aedsp16.c> as well as
	<file:Documentation/sound/oss/AudioExcelDSP16> to get more information
	about this driver and its configuration.

	config SC6600
	bool "SC-6600 based audio cards (new Audio Excel DSP 16)"
	depends on SOUND_AEDSP16
	help
	The SC6600 is the new version of DSP mounted on the Audio Excel DSP
	16 cards. Find in the manual the FCC ID of your audio card and
	answer Y if you have an SC6600 DSP.

	config SC6600_JOY
	bool "Activate SC-6600 Joystick Interface"
	depends on SC6600
	help
	Say Y here in order to use the joystick interface of the Audio Excel
	DSP 16 card.

	config SC6600_CDROM
	int "SC-6600 CDROM Interface (4=None, 3=IDE, 1=Panasonic, 0=?Sony?)"
	depends on SC6600
	default "4"
	help
	This is used to activate the CD-ROM interface of the Audio Excel
	DSP 16 card. Enter: 0 for Sony, 1 for Panasonic, 2 for IDE, 4 for no
	CD-ROM present.

	config SC6600_CDROMBASE
	hex "SC-6600 CDROM Interface I/O Address"
	depends on SC6600
	default "0"
	help
	Base I/O port address for the CD-ROM interface of the Audio Excel
	DSP 16 card.

	config SOUND_VIDC
	tristate "VIDC 16-bit sound"
	depends on ARM && (ARCH_ACORN \|\| ARCH_CLPS7500)
	help
	16-bit support for the VIDC onboard sound hardware found on Acorn
	machines.

	config SOUND_WAVEARTIST
	tristate "Netwinder WaveArtist"
	depends on ARM && ARCH_NETWINDER
	help
	Say Y here to include support for the Rockwell WaveArtist sound
	system. This driver is mainly for the NetWinder.

	config SOUND_KAHLUA
	tristate "XpressAudio Sound Blaster emulation"
	depends on SOUND_SB

	endif # SOUND_OSS

	config SOUND_SH_DAC_AUDIO
	tristate "SuperH DAC audio support"
	depends on CPU_SH3 && HIGH_RES_TIMERS

	config SOUND_SH_DAC_AUDIO_CHANNEL
	int "DAC channel"
	default "1"
	depends on SOUND_SH_DAC_AUDIO