| /* |
| * Marvell 88SE64xx/88SE94xx const head file |
| * |
| * Copyright 2007 Red Hat, Inc. |
| * Copyright 2008 Marvell. <kewei@marvell.com> |
| * |
| * This file is licensed under GPLv2. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of the |
| * License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 |
| * USA |
| */ |
| |
| #ifndef _MV_DEFS_H_ |
| #define _MV_DEFS_H_ |
| |
| |
| enum chip_flavors { |
| chip_6320, |
| chip_6440, |
| chip_6485, |
| chip_9480, |
| chip_9180, |
| }; |
| |
| /* driver compile-time configuration */ |
| enum driver_configuration { |
| MVS_SLOTS = 512, /* command slots */ |
| MVS_TX_RING_SZ = 1024, /* TX ring size (12-bit) */ |
| MVS_RX_RING_SZ = 1024, /* RX ring size (12-bit) */ |
| /* software requires power-of-2 |
| ring size */ |
| MVS_SOC_SLOTS = 64, |
| MVS_SOC_TX_RING_SZ = MVS_SOC_SLOTS * 2, |
| MVS_SOC_RX_RING_SZ = MVS_SOC_SLOTS * 2, |
| |
| MVS_SLOT_BUF_SZ = 8192, /* cmd tbl + IU + status + PRD */ |
| MVS_SSP_CMD_SZ = 64, /* SSP command table buffer size */ |
| MVS_ATA_CMD_SZ = 96, /* SATA command table buffer size */ |
| MVS_OAF_SZ = 64, /* Open address frame buffer size */ |
| MVS_QUEUE_SIZE = 32, /* Support Queue depth */ |
| MVS_CAN_QUEUE = MVS_SLOTS - 2, /* SCSI Queue depth */ |
| MVS_SOC_CAN_QUEUE = MVS_SOC_SLOTS - 2, |
| }; |
| |
| /* unchangeable hardware details */ |
| enum hardware_details { |
| MVS_MAX_PHYS = 8, /* max. possible phys */ |
| MVS_MAX_PORTS = 8, /* max. possible ports */ |
| MVS_SOC_PHYS = 4, /* soc phys */ |
| MVS_SOC_PORTS = 4, /* soc phys */ |
| MVS_MAX_DEVICES = 1024, /* max supported device */ |
| }; |
| |
| /* peripheral registers (BAR2) */ |
| enum peripheral_registers { |
| SPI_CTL = 0x10, /* EEPROM control */ |
| SPI_CMD = 0x14, /* EEPROM command */ |
| SPI_DATA = 0x18, /* EEPROM data */ |
| }; |
| |
| enum peripheral_register_bits { |
| TWSI_RDY = (1U << 7), /* EEPROM interface ready */ |
| TWSI_RD = (1U << 4), /* EEPROM read access */ |
| |
| SPI_ADDR_MASK = 0x3ffff, /* bits 17:0 */ |
| }; |
| |
| enum hw_register_bits { |
| /* MVS_GBL_CTL */ |
| INT_EN = (1U << 1), /* Global int enable */ |
| HBA_RST = (1U << 0), /* HBA reset */ |
| |
| /* MVS_GBL_INT_STAT */ |
| INT_XOR = (1U << 4), /* XOR engine event */ |
| INT_SAS_SATA = (1U << 0), /* SAS/SATA event */ |
| |
| /* MVS_GBL_PORT_TYPE */ /* shl for ports 1-3 */ |
| SATA_TARGET = (1U << 16), /* port0 SATA target enable */ |
| MODE_AUTO_DET_PORT7 = (1U << 15), /* port0 SAS/SATA autodetect */ |
| MODE_AUTO_DET_PORT6 = (1U << 14), |
| MODE_AUTO_DET_PORT5 = (1U << 13), |
| MODE_AUTO_DET_PORT4 = (1U << 12), |
| MODE_AUTO_DET_PORT3 = (1U << 11), |
| MODE_AUTO_DET_PORT2 = (1U << 10), |
| MODE_AUTO_DET_PORT1 = (1U << 9), |
| MODE_AUTO_DET_PORT0 = (1U << 8), |
| MODE_AUTO_DET_EN = MODE_AUTO_DET_PORT0 | MODE_AUTO_DET_PORT1 | |
| MODE_AUTO_DET_PORT2 | MODE_AUTO_DET_PORT3 | |
| MODE_AUTO_DET_PORT4 | MODE_AUTO_DET_PORT5 | |
| MODE_AUTO_DET_PORT6 | MODE_AUTO_DET_PORT7, |
| MODE_SAS_PORT7_MASK = (1U << 7), /* port0 SAS(1), SATA(0) mode */ |
| MODE_SAS_PORT6_MASK = (1U << 6), |
| MODE_SAS_PORT5_MASK = (1U << 5), |
| MODE_SAS_PORT4_MASK = (1U << 4), |
| MODE_SAS_PORT3_MASK = (1U << 3), |
| MODE_SAS_PORT2_MASK = (1U << 2), |
| MODE_SAS_PORT1_MASK = (1U << 1), |
| MODE_SAS_PORT0_MASK = (1U << 0), |
| MODE_SAS_SATA = MODE_SAS_PORT0_MASK | MODE_SAS_PORT1_MASK | |
| MODE_SAS_PORT2_MASK | MODE_SAS_PORT3_MASK | |
| MODE_SAS_PORT4_MASK | MODE_SAS_PORT5_MASK | |
| MODE_SAS_PORT6_MASK | MODE_SAS_PORT7_MASK, |
| |
| /* SAS_MODE value may be |
| * dictated (in hw) by values |
| * of SATA_TARGET & AUTO_DET |
| */ |
| |
| /* MVS_TX_CFG */ |
| TX_EN = (1U << 16), /* Enable TX */ |
| TX_RING_SZ_MASK = 0xfff, /* TX ring size, bits 11:0 */ |
| |
| /* MVS_RX_CFG */ |
| RX_EN = (1U << 16), /* Enable RX */ |
| RX_RING_SZ_MASK = 0xfff, /* RX ring size, bits 11:0 */ |
| |
| /* MVS_INT_COAL */ |
| COAL_EN = (1U << 16), /* Enable int coalescing */ |
| |
| /* MVS_INT_STAT, MVS_INT_MASK */ |
| CINT_I2C = (1U << 31), /* I2C event */ |
| CINT_SW0 = (1U << 30), /* software event 0 */ |
| CINT_SW1 = (1U << 29), /* software event 1 */ |
| CINT_PRD_BC = (1U << 28), /* PRD BC err for read cmd */ |
| CINT_DMA_PCIE = (1U << 27), /* DMA to PCIE timeout */ |
| CINT_MEM = (1U << 26), /* int mem parity err */ |
| CINT_I2C_SLAVE = (1U << 25), /* slave I2C event */ |
| CINT_SRS = (1U << 3), /* SRS event */ |
| CINT_CI_STOP = (1U << 1), /* cmd issue stopped */ |
| CINT_DONE = (1U << 0), /* cmd completion */ |
| |
| /* shl for ports 1-3 */ |
| CINT_PORT_STOPPED = (1U << 16), /* port0 stopped */ |
| CINT_PORT = (1U << 8), /* port0 event */ |
| CINT_PORT_MASK_OFFSET = 8, |
| CINT_PORT_MASK = (0xFF << CINT_PORT_MASK_OFFSET), |
| CINT_PHY_MASK_OFFSET = 4, |
| CINT_PHY_MASK = (0x0F << CINT_PHY_MASK_OFFSET), |
| |
| /* TX (delivery) ring bits */ |
| TXQ_CMD_SHIFT = 29, |
| TXQ_CMD_SSP = 1, /* SSP protocol */ |
| TXQ_CMD_SMP = 2, /* SMP protocol */ |
| TXQ_CMD_STP = 3, /* STP/SATA protocol */ |
| TXQ_CMD_SSP_FREE_LIST = 4, /* add to SSP targ free list */ |
| TXQ_CMD_SLOT_RESET = 7, /* reset command slot */ |
| TXQ_MODE_I = (1U << 28), /* mode: 0=target,1=initiator */ |
| TXQ_MODE_TARGET = 0, |
| TXQ_MODE_INITIATOR = 1, |
| TXQ_PRIO_HI = (1U << 27), /* priority: 0=normal, 1=high */ |
| TXQ_PRI_NORMAL = 0, |
| TXQ_PRI_HIGH = 1, |
| TXQ_SRS_SHIFT = 20, /* SATA register set */ |
| TXQ_SRS_MASK = 0x7f, |
| TXQ_PHY_SHIFT = 12, /* PHY bitmap */ |
| TXQ_PHY_MASK = 0xff, |
| TXQ_SLOT_MASK = 0xfff, /* slot number */ |
| |
| /* RX (completion) ring bits */ |
| RXQ_GOOD = (1U << 23), /* Response good */ |
| RXQ_SLOT_RESET = (1U << 21), /* Slot reset complete */ |
| RXQ_CMD_RX = (1U << 20), /* target cmd received */ |
| RXQ_ATTN = (1U << 19), /* attention */ |
| RXQ_RSP = (1U << 18), /* response frame xfer'd */ |
| RXQ_ERR = (1U << 17), /* err info rec xfer'd */ |
| RXQ_DONE = (1U << 16), /* cmd complete */ |
| RXQ_SLOT_MASK = 0xfff, /* slot number */ |
| |
| /* mvs_cmd_hdr bits */ |
| MCH_PRD_LEN_SHIFT = 16, /* 16-bit PRD table len */ |
| MCH_SSP_FR_TYPE_SHIFT = 13, /* SSP frame type */ |
| |
| /* SSP initiator only */ |
| MCH_SSP_FR_CMD = 0x0, /* COMMAND frame */ |
| |
| /* SSP initiator or target */ |
| MCH_SSP_FR_TASK = 0x1, /* TASK frame */ |
| |
| /* SSP target only */ |
| MCH_SSP_FR_XFER_RDY = 0x4, /* XFER_RDY frame */ |
| MCH_SSP_FR_RESP = 0x5, /* RESPONSE frame */ |
| MCH_SSP_FR_READ = 0x6, /* Read DATA frame(s) */ |
| MCH_SSP_FR_READ_RESP = 0x7, /* ditto, plus RESPONSE */ |
| |
| MCH_SSP_MODE_PASSTHRU = 1, |
| MCH_SSP_MODE_NORMAL = 0, |
| MCH_PASSTHRU = (1U << 12), /* pass-through (SSP) */ |
| MCH_FBURST = (1U << 11), /* first burst (SSP) */ |
| MCH_CHK_LEN = (1U << 10), /* chk xfer len (SSP) */ |
| MCH_RETRY = (1U << 9), /* tport layer retry (SSP) */ |
| MCH_PROTECTION = (1U << 8), /* protection info rec (SSP) */ |
| MCH_RESET = (1U << 7), /* Reset (STP/SATA) */ |
| MCH_FPDMA = (1U << 6), /* First party DMA (STP/SATA) */ |
| MCH_ATAPI = (1U << 5), /* ATAPI (STP/SATA) */ |
| MCH_BIST = (1U << 4), /* BIST activate (STP/SATA) */ |
| MCH_PMP_MASK = 0xf, /* PMP from cmd FIS (STP/SATA)*/ |
| |
| CCTL_RST = (1U << 5), /* port logic reset */ |
| |
| /* 0(LSB first), 1(MSB first) */ |
| CCTL_ENDIAN_DATA = (1U << 3), /* PRD data */ |
| CCTL_ENDIAN_RSP = (1U << 2), /* response frame */ |
| CCTL_ENDIAN_OPEN = (1U << 1), /* open address frame */ |
| CCTL_ENDIAN_CMD = (1U << 0), /* command table */ |
| |
| /* MVS_Px_SER_CTLSTAT (per-phy control) */ |
| PHY_SSP_RST = (1U << 3), /* reset SSP link layer */ |
| PHY_BCAST_CHG = (1U << 2), /* broadcast(change) notif */ |
| PHY_RST_HARD = (1U << 1), /* hard reset + phy reset */ |
| PHY_RST = (1U << 0), /* phy reset */ |
| PHY_READY_MASK = (1U << 20), |
| |
| /* MVS_Px_INT_STAT, MVS_Px_INT_MASK (per-phy events) */ |
| PHYEV_DEC_ERR = (1U << 24), /* Phy Decoding Error */ |
| PHYEV_DCDR_ERR = (1U << 23), /* STP Deocder Error */ |
| PHYEV_CRC_ERR = (1U << 22), /* STP CRC Error */ |
| PHYEV_UNASSOC_FIS = (1U << 19), /* unassociated FIS rx'd */ |
| PHYEV_AN = (1U << 18), /* SATA async notification */ |
| PHYEV_BIST_ACT = (1U << 17), /* BIST activate FIS */ |
| PHYEV_SIG_FIS = (1U << 16), /* signature FIS */ |
| PHYEV_POOF = (1U << 12), /* phy ready from 1 -> 0 */ |
| PHYEV_IU_BIG = (1U << 11), /* IU too long err */ |
| PHYEV_IU_SMALL = (1U << 10), /* IU too short err */ |
| PHYEV_UNK_TAG = (1U << 9), /* unknown tag */ |
| PHYEV_BROAD_CH = (1U << 8), /* broadcast(CHANGE) */ |
| PHYEV_COMWAKE = (1U << 7), /* COMWAKE rx'd */ |
| PHYEV_PORT_SEL = (1U << 6), /* port selector present */ |
| PHYEV_HARD_RST = (1U << 5), /* hard reset rx'd */ |
| PHYEV_ID_TMOUT = (1U << 4), /* identify timeout */ |
| PHYEV_ID_FAIL = (1U << 3), /* identify failed */ |
| PHYEV_ID_DONE = (1U << 2), /* identify done */ |
| PHYEV_HARD_RST_DONE = (1U << 1), /* hard reset done */ |
| PHYEV_RDY_CH = (1U << 0), /* phy ready changed state */ |
| |
| /* MVS_PCS */ |
| PCS_EN_SATA_REG_SHIFT = (16), /* Enable SATA Register Set */ |
| PCS_EN_PORT_XMT_SHIFT = (12), /* Enable Port Transmit */ |
| PCS_EN_PORT_XMT_SHIFT2 = (8), /* For 6485 */ |
| PCS_SATA_RETRY = (1U << 8), /* retry ctl FIS on R_ERR */ |
| PCS_RSP_RX_EN = (1U << 7), /* raw response rx */ |
| PCS_SATA_RETRY_2 = (1U << 6), /* For 9180 */ |
| PCS_SELF_CLEAR = (1U << 5), /* self-clearing int mode */ |
| PCS_FIS_RX_EN = (1U << 4), /* FIS rx enable */ |
| PCS_CMD_STOP_ERR = (1U << 3), /* cmd stop-on-err enable */ |
| PCS_CMD_RST = (1U << 1), /* reset cmd issue */ |
| PCS_CMD_EN = (1U << 0), /* enable cmd issue */ |
| |
| /* Port n Attached Device Info */ |
| PORT_DEV_SSP_TRGT = (1U << 19), |
| PORT_DEV_SMP_TRGT = (1U << 18), |
| PORT_DEV_STP_TRGT = (1U << 17), |
| PORT_DEV_SSP_INIT = (1U << 11), |
| PORT_DEV_SMP_INIT = (1U << 10), |
| PORT_DEV_STP_INIT = (1U << 9), |
| PORT_PHY_ID_MASK = (0xFFU << 24), |
| PORT_SSP_TRGT_MASK = (0x1U << 19), |
| PORT_SSP_INIT_MASK = (0x1U << 11), |
| PORT_DEV_TRGT_MASK = (0x7U << 17), |
| PORT_DEV_INIT_MASK = (0x7U << 9), |
| PORT_DEV_TYPE_MASK = (0x7U << 0), |
| |
| /* Port n PHY Status */ |
| PHY_RDY = (1U << 2), |
| PHY_DW_SYNC = (1U << 1), |
| PHY_OOB_DTCTD = (1U << 0), |
| |
| /* VSR */ |
| /* PHYMODE 6 (CDB) */ |
| PHY_MODE6_LATECLK = (1U << 29), /* Lock Clock */ |
| PHY_MODE6_DTL_SPEED = (1U << 27), /* Digital Loop Speed */ |
| PHY_MODE6_FC_ORDER = (1U << 26), /* Fibre Channel Mode Order*/ |
| PHY_MODE6_MUCNT_EN = (1U << 24), /* u Count Enable */ |
| PHY_MODE6_SEL_MUCNT_LEN = (1U << 22), /* Training Length Select */ |
| PHY_MODE6_SELMUPI = (1U << 20), /* Phase Multi Select (init) */ |
| PHY_MODE6_SELMUPF = (1U << 18), /* Phase Multi Select (final) */ |
| PHY_MODE6_SELMUFF = (1U << 16), /* Freq Loop Multi Sel(final) */ |
| PHY_MODE6_SELMUFI = (1U << 14), /* Freq Loop Multi Sel(init) */ |
| PHY_MODE6_FREEZE_LOOP = (1U << 12), /* Freeze Rx CDR Loop */ |
| PHY_MODE6_INT_RXFOFFS = (1U << 3), /* Rx CDR Freq Loop Enable */ |
| PHY_MODE6_FRC_RXFOFFS = (1U << 2), /* Initial Rx CDR Offset */ |
| PHY_MODE6_STAU_0D8 = (1U << 1), /* Rx CDR Freq Loop Saturate */ |
| PHY_MODE6_RXSAT_DIS = (1U << 0), /* Saturate Ctl */ |
| }; |
| |
| /* SAS/SATA configuration port registers, aka phy registers */ |
| enum sas_sata_config_port_regs { |
| PHYR_IDENTIFY = 0x00, /* info for IDENTIFY frame */ |
| PHYR_ADDR_LO = 0x04, /* my SAS address (low) */ |
| PHYR_ADDR_HI = 0x08, /* my SAS address (high) */ |
| PHYR_ATT_DEV_INFO = 0x0C, /* attached device info */ |
| PHYR_ATT_ADDR_LO = 0x10, /* attached dev SAS addr (low) */ |
| PHYR_ATT_ADDR_HI = 0x14, /* attached dev SAS addr (high) */ |
| PHYR_SATA_CTL = 0x18, /* SATA control */ |
| PHYR_PHY_STAT = 0x1C, /* PHY status */ |
| PHYR_SATA_SIG0 = 0x20, /*port SATA signature FIS(Byte 0-3) */ |
| PHYR_SATA_SIG1 = 0x24, /*port SATA signature FIS(Byte 4-7) */ |
| PHYR_SATA_SIG2 = 0x28, /*port SATA signature FIS(Byte 8-11) */ |
| PHYR_SATA_SIG3 = 0x2c, /*port SATA signature FIS(Byte 12-15) */ |
| PHYR_R_ERR_COUNT = 0x30, /* port R_ERR count register */ |
| PHYR_CRC_ERR_COUNT = 0x34, /* port CRC error count register */ |
| PHYR_WIDE_PORT = 0x38, /* wide port participating */ |
| PHYR_CURRENT0 = 0x80, /* current connection info 0 */ |
| PHYR_CURRENT1 = 0x84, /* current connection info 1 */ |
| PHYR_CURRENT2 = 0x88, /* current connection info 2 */ |
| CONFIG_ID_FRAME0 = 0x100, /* Port device ID frame register 0 */ |
| CONFIG_ID_FRAME1 = 0x104, /* Port device ID frame register 1 */ |
| CONFIG_ID_FRAME2 = 0x108, /* Port device ID frame register 2 */ |
| CONFIG_ID_FRAME3 = 0x10c, /* Port device ID frame register 3 */ |
| CONFIG_ID_FRAME4 = 0x110, /* Port device ID frame register 4 */ |
| CONFIG_ID_FRAME5 = 0x114, /* Port device ID frame register 5 */ |
| CONFIG_ID_FRAME6 = 0x118, /* Port device ID frame register 6 */ |
| CONFIG_ATT_ID_FRAME0 = 0x11c, /* attached ID frame register 0 */ |
| CONFIG_ATT_ID_FRAME1 = 0x120, /* attached ID frame register 1 */ |
| CONFIG_ATT_ID_FRAME2 = 0x124, /* attached ID frame register 2 */ |
| CONFIG_ATT_ID_FRAME3 = 0x128, /* attached ID frame register 3 */ |
| CONFIG_ATT_ID_FRAME4 = 0x12c, /* attached ID frame register 4 */ |
| CONFIG_ATT_ID_FRAME5 = 0x130, /* attached ID frame register 5 */ |
| CONFIG_ATT_ID_FRAME6 = 0x134, /* attached ID frame register 6 */ |
| }; |
| |
| enum sas_cmd_port_registers { |
| CMD_CMRST_OOB_DET = 0x100, /* COMRESET OOB detect register */ |
| CMD_CMWK_OOB_DET = 0x104, /* COMWAKE OOB detect register */ |
| CMD_CMSAS_OOB_DET = 0x108, /* COMSAS OOB detect register */ |
| CMD_BRST_OOB_DET = 0x10c, /* burst OOB detect register */ |
| CMD_OOB_SPACE = 0x110, /* OOB space control register */ |
| CMD_OOB_BURST = 0x114, /* OOB burst control register */ |
| CMD_PHY_TIMER = 0x118, /* PHY timer control register */ |
| CMD_PHY_CONFIG0 = 0x11c, /* PHY config register 0 */ |
| CMD_PHY_CONFIG1 = 0x120, /* PHY config register 1 */ |
| CMD_SAS_CTL0 = 0x124, /* SAS control register 0 */ |
| CMD_SAS_CTL1 = 0x128, /* SAS control register 1 */ |
| CMD_SAS_CTL2 = 0x12c, /* SAS control register 2 */ |
| CMD_SAS_CTL3 = 0x130, /* SAS control register 3 */ |
| CMD_ID_TEST = 0x134, /* ID test register */ |
| CMD_PL_TIMER = 0x138, /* PL timer register */ |
| CMD_WD_TIMER = 0x13c, /* WD timer register */ |
| CMD_PORT_SEL_COUNT = 0x140, /* port selector count register */ |
| CMD_APP_MEM_CTL = 0x144, /* Application Memory Control */ |
| CMD_XOR_MEM_CTL = 0x148, /* XOR Block Memory Control */ |
| CMD_DMA_MEM_CTL = 0x14c, /* DMA Block Memory Control */ |
| CMD_PORT_MEM_CTL0 = 0x150, /* Port Memory Control 0 */ |
| CMD_PORT_MEM_CTL1 = 0x154, /* Port Memory Control 1 */ |
| CMD_SATA_PORT_MEM_CTL0 = 0x158, /* SATA Port Memory Control 0 */ |
| CMD_SATA_PORT_MEM_CTL1 = 0x15c, /* SATA Port Memory Control 1 */ |
| CMD_XOR_MEM_BIST_CTL = 0x160, /* XOR Memory BIST Control */ |
| CMD_XOR_MEM_BIST_STAT = 0x164, /* XOR Memroy BIST Status */ |
| CMD_DMA_MEM_BIST_CTL = 0x168, /* DMA Memory BIST Control */ |
| CMD_DMA_MEM_BIST_STAT = 0x16c, /* DMA Memory BIST Status */ |
| CMD_PORT_MEM_BIST_CTL = 0x170, /* Port Memory BIST Control */ |
| CMD_PORT_MEM_BIST_STAT0 = 0x174, /* Port Memory BIST Status 0 */ |
| CMD_PORT_MEM_BIST_STAT1 = 0x178, /* Port Memory BIST Status 1 */ |
| CMD_STP_MEM_BIST_CTL = 0x17c, /* STP Memory BIST Control */ |
| CMD_STP_MEM_BIST_STAT0 = 0x180, /* STP Memory BIST Status 0 */ |
| CMD_STP_MEM_BIST_STAT1 = 0x184, /* STP Memory BIST Status 1 */ |
| CMD_RESET_COUNT = 0x188, /* Reset Count */ |
| CMD_MONTR_DATA_SEL = 0x18C, /* Monitor Data/Select */ |
| CMD_PLL_PHY_CONFIG = 0x190, /* PLL/PHY Configuration */ |
| CMD_PHY_CTL = 0x194, /* PHY Control and Status */ |
| CMD_PHY_TEST_COUNT0 = 0x198, /* Phy Test Count 0 */ |
| CMD_PHY_TEST_COUNT1 = 0x19C, /* Phy Test Count 1 */ |
| CMD_PHY_TEST_COUNT2 = 0x1A0, /* Phy Test Count 2 */ |
| CMD_APP_ERR_CONFIG = 0x1A4, /* Application Error Configuration */ |
| CMD_PND_FIFO_CTL0 = 0x1A8, /* Pending FIFO Control 0 */ |
| CMD_HOST_CTL = 0x1AC, /* Host Control Status */ |
| CMD_HOST_WR_DATA = 0x1B0, /* Host Write Data */ |
| CMD_HOST_RD_DATA = 0x1B4, /* Host Read Data */ |
| CMD_PHY_MODE_21 = 0x1B8, /* Phy Mode 21 */ |
| CMD_SL_MODE0 = 0x1BC, /* SL Mode 0 */ |
| CMD_SL_MODE1 = 0x1C0, /* SL Mode 1 */ |
| CMD_PND_FIFO_CTL1 = 0x1C4, /* Pending FIFO Control 1 */ |
| }; |
| |
| enum mvs_info_flags { |
| MVF_MSI = (1U << 0), /* MSI is enabled */ |
| MVF_PHY_PWR_FIX = (1U << 1), /* bug workaround */ |
| MVF_FLAG_SOC = (1U << 2), /* SoC integrated controllers */ |
| }; |
| |
| enum mvs_event_flags { |
| PHY_PLUG_EVENT = (3U), |
| PHY_PLUG_IN = (1U << 0), /* phy plug in */ |
| PHY_PLUG_OUT = (1U << 1), /* phy plug out */ |
| }; |
| |
| enum mvs_port_type { |
| PORT_TGT_MASK = (1U << 5), |
| PORT_INIT_PORT = (1U << 4), |
| PORT_TGT_PORT = (1U << 3), |
| PORT_INIT_TGT_PORT = (PORT_INIT_PORT | PORT_TGT_PORT), |
| PORT_TYPE_SAS = (1U << 1), |
| PORT_TYPE_SATA = (1U << 0), |
| }; |
| |
| /* Command Table Format */ |
| enum ct_format { |
| /* SSP */ |
| SSP_F_H = 0x00, |
| SSP_F_IU = 0x18, |
| SSP_F_MAX = 0x4D, |
| /* STP */ |
| STP_CMD_FIS = 0x00, |
| STP_ATAPI_CMD = 0x40, |
| STP_F_MAX = 0x10, |
| /* SMP */ |
| SMP_F_T = 0x00, |
| SMP_F_DEP = 0x01, |
| SMP_F_MAX = 0x101, |
| }; |
| |
| enum status_buffer { |
| SB_EIR_OFF = 0x00, /* Error Information Record */ |
| SB_RFB_OFF = 0x08, /* Response Frame Buffer */ |
| SB_RFB_MAX = 0x400, /* RFB size*/ |
| }; |
| |
| enum error_info_rec { |
| CMD_ISS_STPD = (1U << 31), /* Cmd Issue Stopped */ |
| CMD_PI_ERR = (1U << 30), /* Protection info error. see flags2 */ |
| RSP_OVER = (1U << 29), /* rsp buffer overflow */ |
| RETRY_LIM = (1U << 28), /* FIS/frame retry limit exceeded */ |
| UNK_FIS = (1U << 27), /* unknown FIS */ |
| DMA_TERM = (1U << 26), /* DMA terminate primitive rx'd */ |
| SYNC_ERR = (1U << 25), /* SYNC rx'd during frame xmit */ |
| TFILE_ERR = (1U << 24), /* SATA taskfile Error bit set */ |
| R_ERR = (1U << 23), /* SATA returned R_ERR prim */ |
| RD_OFS = (1U << 20), /* Read DATA frame invalid offset */ |
| XFER_RDY_OFS = (1U << 19), /* XFER_RDY offset error */ |
| UNEXP_XFER_RDY = (1U << 18), /* unexpected XFER_RDY error */ |
| DATA_OVER_UNDER = (1U << 16), /* data overflow/underflow */ |
| INTERLOCK = (1U << 15), /* interlock error */ |
| NAK = (1U << 14), /* NAK rx'd */ |
| ACK_NAK_TO = (1U << 13), /* ACK/NAK timeout */ |
| CXN_CLOSED = (1U << 12), /* cxn closed w/out ack/nak */ |
| OPEN_TO = (1U << 11), /* I_T nexus lost, open cxn timeout */ |
| PATH_BLOCKED = (1U << 10), /* I_T nexus lost, pathway blocked */ |
| NO_DEST = (1U << 9), /* I_T nexus lost, no destination */ |
| STP_RES_BSY = (1U << 8), /* STP resources busy */ |
| BREAK = (1U << 7), /* break received */ |
| BAD_DEST = (1U << 6), /* bad destination */ |
| BAD_PROTO = (1U << 5), /* protocol not supported */ |
| BAD_RATE = (1U << 4), /* cxn rate not supported */ |
| WRONG_DEST = (1U << 3), /* wrong destination error */ |
| CREDIT_TO = (1U << 2), /* credit timeout */ |
| WDOG_TO = (1U << 1), /* watchdog timeout */ |
| BUF_PAR = (1U << 0), /* buffer parity error */ |
| }; |
| |
| enum error_info_rec_2 { |
| SLOT_BSY_ERR = (1U << 31), /* Slot Busy Error */ |
| GRD_CHK_ERR = (1U << 14), /* Guard Check Error */ |
| APP_CHK_ERR = (1U << 13), /* Application Check error */ |
| REF_CHK_ERR = (1U << 12), /* Reference Check Error */ |
| USR_BLK_NM = (1U << 0), /* User Block Number */ |
| }; |
| |
| enum pci_cfg_register_bits { |
| PCTL_PWR_OFF = (0xFU << 24), |
| PCTL_COM_ON = (0xFU << 20), |
| PCTL_LINK_RST = (0xFU << 16), |
| PCTL_LINK_OFFS = (16), |
| PCTL_PHY_DSBL = (0xFU << 12), |
| PCTL_PHY_DSBL_OFFS = (12), |
| PRD_REQ_SIZE = (0x4000), |
| PRD_REQ_MASK = (0x00007000), |
| PLS_NEG_LINK_WD = (0x3FU << 4), |
| PLS_NEG_LINK_WD_OFFS = 4, |
| PLS_LINK_SPD = (0x0FU << 0), |
| PLS_LINK_SPD_OFFS = 0, |
| }; |
| |
| enum open_frame_protocol { |
| PROTOCOL_SMP = 0x0, |
| PROTOCOL_SSP = 0x1, |
| PROTOCOL_STP = 0x2, |
| }; |
| |
| /* define for response frame datapres field */ |
| enum datapres_field { |
| NO_DATA = 0, |
| RESPONSE_DATA = 1, |
| SENSE_DATA = 2, |
| }; |
| |
| /* define task management IU */ |
| struct mvs_tmf_task{ |
| u8 tmf; |
| u16 tag_of_task_to_be_managed; |
| }; |
| #endif |