blob: 938d185841c9eeb138f04b6c3389d48a03d0a11c [file] [log] [blame]
/*
* linux/drivers/char/amba.c
*
* Driver for AMBA serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright 1999 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* $Id: amba.c,v 1.41 2002/07/28 10:03:27 rmk Exp $
*
* This is a generic driver for ARM AMBA-type serial ports. They
* have a lot of 16550-like features, but are not register compatible.
* Note that although they do have CTS, DCD and DSR inputs, they do
* not have an RI input, nor do they have DTR or RTS outputs. If
* required, these have to be supplied via some other means (eg, GPIO)
* and hooked into this driver.
*/
#include <linux/config.h>
#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif
#include <linux/module.h>
#include <linux/ioport.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/sysrq.h>
#include <linux/device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/sizes.h>
#include <asm/hardware/amba.h>
#include <asm/hardware/clock.h>
#include <asm/hardware/amba_serial.h>
#define UART_NR 14
#define SERIAL_AMBA_MAJOR 204
#define SERIAL_AMBA_MINOR 64
#define SERIAL_AMBA_NR UART_NR
#define AMBA_ISR_PASS_LIMIT 256
#define UART_DUMMY_RSR_RX 256
/*
* We wrap our port structure around the generic uart_port.
*/
struct uart_amba_port {
struct uart_port port;
struct clk *clk;
unsigned int im; /* interrupt mask */
unsigned int old_status;
};
static void pl011_stop_tx(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
uap->im &= ~UART011_TXIM;
writew(uap->im, uap->port.membase + UART011_IMSC);
}
static void pl011_start_tx(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
uap->im |= UART011_TXIM;
writew(uap->im, uap->port.membase + UART011_IMSC);
}
static void pl011_stop_rx(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
UART011_PEIM|UART011_BEIM|UART011_OEIM);
writew(uap->im, uap->port.membase + UART011_IMSC);
}
static void pl011_enable_ms(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
writew(uap->im, uap->port.membase + UART011_IMSC);
}
static void
#ifdef SUPPORT_SYSRQ
pl011_rx_chars(struct uart_amba_port *uap, struct pt_regs *regs)
#else
pl011_rx_chars(struct uart_amba_port *uap)
#endif
{
struct tty_struct *tty = uap->port.info->tty;
unsigned int status, ch, flag, rsr, max_count = 256;
status = readw(uap->port.membase + UART01x_FR);
while ((status & UART01x_FR_RXFE) == 0 && max_count--) {
if (tty->flip.count >= TTY_FLIPBUF_SIZE) {
if (tty->low_latency)
tty_flip_buffer_push(tty);
/*
* If this failed then we will throw away the
* bytes but must do so to clear interrupts
*/
}
ch = readw(uap->port.membase + UART01x_DR);
flag = TTY_NORMAL;
uap->port.icount.rx++;
/*
* Note that the error handling code is
* out of the main execution path
*/
rsr = readw(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
if (unlikely(rsr & UART01x_RSR_ANY)) {
if (rsr & UART01x_RSR_BE) {
rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
uap->port.icount.brk++;
if (uart_handle_break(&uap->port))
goto ignore_char;
} else if (rsr & UART01x_RSR_PE)
uap->port.icount.parity++;
else if (rsr & UART01x_RSR_FE)
uap->port.icount.frame++;
if (rsr & UART01x_RSR_OE)
uap->port.icount.overrun++;
rsr &= uap->port.read_status_mask;
if (rsr & UART01x_RSR_BE)
flag = TTY_BREAK;
else if (rsr & UART01x_RSR_PE)
flag = TTY_PARITY;
else if (rsr & UART01x_RSR_FE)
flag = TTY_FRAME;
}
if (uart_handle_sysrq_char(&uap->port, ch, regs))
goto ignore_char;
uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
ignore_char:
status = readw(uap->port.membase + UART01x_FR);
}
tty_flip_buffer_push(tty);
return;
}
static void pl011_tx_chars(struct uart_amba_port *uap)
{
struct circ_buf *xmit = &uap->port.info->xmit;
int count;
if (uap->port.x_char) {
writew(uap->port.x_char, uap->port.membase + UART01x_DR);
uap->port.icount.tx++;
uap->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
pl011_stop_tx(&uap->port);
return;
}
count = uap->port.fifosize >> 1;
do {
writew(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
uap->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&uap->port);
if (uart_circ_empty(xmit))
pl011_stop_tx(&uap->port);
}
static void pl011_modem_status(struct uart_amba_port *uap)
{
unsigned int status, delta;
status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
delta = status ^ uap->old_status;
uap->old_status = status;
if (!delta)
return;
if (delta & UART01x_FR_DCD)
uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
if (delta & UART01x_FR_DSR)
uap->port.icount.dsr++;
if (delta & UART01x_FR_CTS)
uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
wake_up_interruptible(&uap->port.info->delta_msr_wait);
}
static irqreturn_t pl011_int(int irq, void *dev_id, struct pt_regs *regs)
{
struct uart_amba_port *uap = dev_id;
unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
int handled = 0;
spin_lock(&uap->port.lock);
status = readw(uap->port.membase + UART011_MIS);
if (status) {
do {
writew(status & ~(UART011_TXIS|UART011_RTIS|
UART011_RXIS),
uap->port.membase + UART011_ICR);
if (status & (UART011_RTIS|UART011_RXIS))
#ifdef SUPPORT_SYSRQ
pl011_rx_chars(uap, regs);
#else
pl011_rx_chars(uap);
#endif
if (status & (UART011_DSRMIS|UART011_DCDMIS|
UART011_CTSMIS|UART011_RIMIS))
pl011_modem_status(uap);
if (status & UART011_TXIS)
pl011_tx_chars(uap);
if (pass_counter-- == 0)
break;
status = readw(uap->port.membase + UART011_MIS);
} while (status != 0);
handled = 1;
}
spin_unlock(&uap->port.lock);
return IRQ_RETVAL(handled);
}
static unsigned int pl01x_tx_empty(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int status = readw(uap->port.membase + UART01x_FR);
return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
}
static unsigned int pl01x_get_mctrl(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int result = 0;
unsigned int status = readw(uap->port.membase + UART01x_FR);
#define BIT(uartbit, tiocmbit) \
if (status & uartbit) \
result |= tiocmbit
BIT(UART01x_FR_DCD, TIOCM_CAR);
BIT(UART01x_FR_DSR, TIOCM_DSR);
BIT(UART01x_FR_CTS, TIOCM_CTS);
BIT(UART011_FR_RI, TIOCM_RNG);
#undef BIT
return result;
}
static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
cr = readw(uap->port.membase + UART011_CR);
#define BIT(tiocmbit, uartbit) \
if (mctrl & tiocmbit) \
cr |= uartbit; \
else \
cr &= ~uartbit
BIT(TIOCM_RTS, UART011_CR_RTS);
BIT(TIOCM_DTR, UART011_CR_DTR);
BIT(TIOCM_OUT1, UART011_CR_OUT1);
BIT(TIOCM_OUT2, UART011_CR_OUT2);
BIT(TIOCM_LOOP, UART011_CR_LBE);
#undef BIT
writew(cr, uap->port.membase + UART011_CR);
}
static void pl011_break_ctl(struct uart_port *port, int break_state)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned long flags;
unsigned int lcr_h;
spin_lock_irqsave(&uap->port.lock, flags);
lcr_h = readw(uap->port.membase + UART011_LCRH);
if (break_state == -1)
lcr_h |= UART01x_LCRH_BRK;
else
lcr_h &= ~UART01x_LCRH_BRK;
writew(lcr_h, uap->port.membase + UART011_LCRH);
spin_unlock_irqrestore(&uap->port.lock, flags);
}
static int pl011_startup(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
int retval;
/*
* Try to enable the clock producer.
*/
retval = clk_enable(uap->clk);
if (retval)
goto out;
uap->port.uartclk = clk_get_rate(uap->clk);
/*
* Allocate the IRQ
*/
retval = request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
if (retval)
goto clk_dis;
writew(UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
uap->port.membase + UART011_IFLS);
/*
* Provoke TX FIFO interrupt into asserting.
*/
cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE;
writew(cr, uap->port.membase + UART011_CR);
writew(0, uap->port.membase + UART011_FBRD);
writew(1, uap->port.membase + UART011_IBRD);
writew(0, uap->port.membase + UART011_LCRH);
writew(0, uap->port.membase + UART01x_DR);
while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
barrier();
cr = UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
writew(cr, uap->port.membase + UART011_CR);
/*
* initialise the old status of the modem signals
*/
uap->old_status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
/*
* Finally, enable interrupts
*/
spin_lock_irq(&uap->port.lock);
uap->im = UART011_RXIM | UART011_RTIM;
writew(uap->im, uap->port.membase + UART011_IMSC);
spin_unlock_irq(&uap->port.lock);
return 0;
clk_dis:
clk_disable(uap->clk);
out:
return retval;
}
static void pl011_shutdown(struct uart_port *port)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned long val;
/*
* disable all interrupts
*/
spin_lock_irq(&uap->port.lock);
uap->im = 0;
writew(uap->im, uap->port.membase + UART011_IMSC);
writew(0xffff, uap->port.membase + UART011_ICR);
spin_unlock_irq(&uap->port.lock);
/*
* Free the interrupt
*/
free_irq(uap->port.irq, uap);
/*
* disable the port
*/
writew(UART01x_CR_UARTEN | UART011_CR_TXE, uap->port.membase + UART011_CR);
/*
* disable break condition and fifos
*/
val = readw(uap->port.membase + UART011_LCRH);
val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN);
writew(val, uap->port.membase + UART011_LCRH);
/*
* Shut down the clock producer
*/
clk_disable(uap->clk);
}
static void
pl011_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
unsigned int lcr_h, old_cr;
unsigned long flags;
unsigned int baud, quot;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = port->uartclk * 4 / baud;
switch (termios->c_cflag & CSIZE) {
case CS5:
lcr_h = UART01x_LCRH_WLEN_5;
break;
case CS6:
lcr_h = UART01x_LCRH_WLEN_6;
break;
case CS7:
lcr_h = UART01x_LCRH_WLEN_7;
break;
default: // CS8
lcr_h = UART01x_LCRH_WLEN_8;
break;
}
if (termios->c_cflag & CSTOPB)
lcr_h |= UART01x_LCRH_STP2;
if (termios->c_cflag & PARENB) {
lcr_h |= UART01x_LCRH_PEN;
if (!(termios->c_cflag & PARODD))
lcr_h |= UART01x_LCRH_EPS;
}
if (port->fifosize > 1)
lcr_h |= UART01x_LCRH_FEN;
spin_lock_irqsave(&port->lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
port->read_status_mask = UART01x_RSR_OE;
if (termios->c_iflag & INPCK)
port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= UART01x_RSR_BE;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= UART01x_RSR_BE;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UART01x_RSR_OE;
}
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= UART_DUMMY_RSR_RX;
if (UART_ENABLE_MS(port, termios->c_cflag))
pl011_enable_ms(port);
/* first, disable everything */
old_cr = readw(port->membase + UART011_CR);
writew(0, port->membase + UART011_CR);
/* Set baud rate */
writew(quot & 0x3f, port->membase + UART011_FBRD);
writew(quot >> 6, port->membase + UART011_IBRD);
/*
* ----------v----------v----------v----------v-----
* NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
* ----------^----------^----------^----------^-----
*/
writew(lcr_h, port->membase + UART011_LCRH);
writew(old_cr, port->membase + UART011_CR);
spin_unlock_irqrestore(&port->lock, flags);
}
static const char *pl011_type(struct uart_port *port)
{
return port->type == PORT_AMBA ? "AMBA/PL011" : NULL;
}
/*
* Release the memory region(s) being used by 'port'
*/
static void pl010_release_port(struct uart_port *port)
{
release_mem_region(port->mapbase, SZ_4K);
}
/*
* Request the memory region(s) being used by 'port'
*/
static int pl010_request_port(struct uart_port *port)
{
return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
!= NULL ? 0 : -EBUSY;
}
/*
* Configure/autoconfigure the port.
*/
static void pl010_config_port(struct uart_port *port, int flags)
{
if (flags & UART_CONFIG_TYPE) {
port->type = PORT_AMBA;
pl010_request_port(port);
}
}
/*
* verify the new serial_struct (for TIOCSSERIAL).
*/
static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
{
int ret = 0;
if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
ret = -EINVAL;
if (ser->irq < 0 || ser->irq >= NR_IRQS)
ret = -EINVAL;
if (ser->baud_base < 9600)
ret = -EINVAL;
return ret;
}
static struct uart_ops amba_pl011_pops = {
.tx_empty = pl01x_tx_empty,
.set_mctrl = pl011_set_mctrl,
.get_mctrl = pl01x_get_mctrl,
.stop_tx = pl011_stop_tx,
.start_tx = pl011_start_tx,
.stop_rx = pl011_stop_rx,
.enable_ms = pl011_enable_ms,
.break_ctl = pl011_break_ctl,
.startup = pl011_startup,
.shutdown = pl011_shutdown,
.set_termios = pl011_set_termios,
.type = pl011_type,
.release_port = pl010_release_port,
.request_port = pl010_request_port,
.config_port = pl010_config_port,
.verify_port = pl010_verify_port,
};
static struct uart_amba_port *amba_ports[UART_NR];
#ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
static inline void
pl011_console_write_char(struct uart_amba_port *uap, char ch)
{
unsigned int status;
do {
status = readw(uap->port.membase + UART01x_FR);
} while (status & UART01x_FR_TXFF);
writew(ch, uap->port.membase + UART01x_DR);
}
static void
pl011_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_amba_port *uap = amba_ports[co->index];
unsigned int status, old_cr, new_cr;
int i;
clk_enable(uap->clk);
/*
* First save the CR then disable the interrupts
*/
old_cr = readw(uap->port.membase + UART011_CR);
new_cr = old_cr & ~UART011_CR_CTSEN;
new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
writew(new_cr, uap->port.membase + UART011_CR);
/*
* Now, do each character
*/
for (i = 0; i < count; i++) {
pl011_console_write_char(uap, s[i]);
if (s[i] == '\n')
pl011_console_write_char(uap, '\r');
}
/*
* Finally, wait for transmitter to become empty
* and restore the TCR
*/
do {
status = readw(uap->port.membase + UART01x_FR);
} while (status & UART01x_FR_BUSY);
writew(old_cr, uap->port.membase + UART011_CR);
clk_disable(uap->clk);
}
static void __init
pl011_console_get_options(struct uart_amba_port *uap, int *baud,
int *parity, int *bits)
{
if (readw(uap->port.membase + UART011_CR) & UART01x_CR_UARTEN) {
unsigned int lcr_h, ibrd, fbrd;
lcr_h = readw(uap->port.membase + UART011_LCRH);
*parity = 'n';
if (lcr_h & UART01x_LCRH_PEN) {
if (lcr_h & UART01x_LCRH_EPS)
*parity = 'e';
else
*parity = 'o';
}
if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
*bits = 7;
else
*bits = 8;
ibrd = readw(uap->port.membase + UART011_IBRD);
fbrd = readw(uap->port.membase + UART011_FBRD);
*baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
}
}
static int __init pl011_console_setup(struct console *co, char *options)
{
struct uart_amba_port *uap;
int baud = 38400;
int bits = 8;
int parity = 'n';
int flow = 'n';
/*
* Check whether an invalid uart number has been specified, and
* if so, search for the first available port that does have
* console support.
*/
if (co->index >= UART_NR)
co->index = 0;
uap = amba_ports[co->index];
uap->port.uartclk = clk_get_rate(uap->clk);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
pl011_console_get_options(uap, &baud, &parity, &bits);
return uart_set_options(&uap->port, co, baud, parity, bits, flow);
}
static struct uart_driver amba_reg;
static struct console amba_console = {
.name = "ttyAMA",
.write = pl011_console_write,
.device = uart_console_device,
.setup = pl011_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
.data = &amba_reg,
};
#define AMBA_CONSOLE (&amba_console)
#else
#define AMBA_CONSOLE NULL
#endif
static struct uart_driver amba_reg = {
.owner = THIS_MODULE,
.driver_name = "ttyAMA",
.dev_name = "ttyAMA",
.major = SERIAL_AMBA_MAJOR,
.minor = SERIAL_AMBA_MINOR,
.nr = UART_NR,
.cons = AMBA_CONSOLE,
};
static int pl011_probe(struct amba_device *dev, void *id)
{
struct uart_amba_port *uap;
void __iomem *base;
int i, ret;
for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
if (amba_ports[i] == NULL)
break;
if (i == ARRAY_SIZE(amba_ports)) {
ret = -EBUSY;
goto out;
}
uap = kmalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
if (uap == NULL) {
ret = -ENOMEM;
goto out;
}
base = ioremap(dev->res.start, PAGE_SIZE);
if (!base) {
ret = -ENOMEM;
goto free;
}
memset(uap, 0, sizeof(struct uart_amba_port));
uap->clk = clk_get(&dev->dev, "UARTCLK");
if (IS_ERR(uap->clk)) {
ret = PTR_ERR(uap->clk);
goto unmap;
}
ret = clk_use(uap->clk);
if (ret)
goto putclk;
uap->port.dev = &dev->dev;
uap->port.mapbase = dev->res.start;
uap->port.membase = base;
uap->port.iotype = UPIO_MEM;
uap->port.irq = dev->irq[0];
uap->port.fifosize = 16;
uap->port.ops = &amba_pl011_pops;
uap->port.flags = UPF_BOOT_AUTOCONF;
uap->port.line = i;
amba_ports[i] = uap;
amba_set_drvdata(dev, uap);
ret = uart_add_one_port(&amba_reg, &uap->port);
if (ret) {
amba_set_drvdata(dev, NULL);
amba_ports[i] = NULL;
clk_unuse(uap->clk);
putclk:
clk_put(uap->clk);
unmap:
iounmap(base);
free:
kfree(uap);
}
out:
return ret;
}
static int pl011_remove(struct amba_device *dev)
{
struct uart_amba_port *uap = amba_get_drvdata(dev);
int i;
amba_set_drvdata(dev, NULL);
uart_remove_one_port(&amba_reg, &uap->port);
for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
if (amba_ports[i] == uap)
amba_ports[i] = NULL;
iounmap(uap->port.membase);
clk_unuse(uap->clk);
clk_put(uap->clk);
kfree(uap);
return 0;
}
static struct amba_id pl011_ids[] __initdata = {
{
.id = 0x00041011,
.mask = 0x000fffff,
},
{ 0, 0 },
};
static struct amba_driver pl011_driver = {
.drv = {
.name = "uart-pl011",
},
.id_table = pl011_ids,
.probe = pl011_probe,
.remove = pl011_remove,
};
static int __init pl011_init(void)
{
int ret;
printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
ret = uart_register_driver(&amba_reg);
if (ret == 0) {
ret = amba_driver_register(&pl011_driver);
if (ret)
uart_unregister_driver(&amba_reg);
}
return ret;
}
static void __exit pl011_exit(void)
{
amba_driver_unregister(&pl011_driver);
uart_unregister_driver(&amba_reg);
}
module_init(pl011_init);
module_exit(pl011_exit);
MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
MODULE_DESCRIPTION("ARM AMBA serial port driver");
MODULE_LICENSE("GPL");