| /* |
| * Intel IXP4xx Ethernet driver for Linux |
| * |
| * Copyright (C) 2007 Krzysztof Halasa <khc@pm.waw.pl> |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of version 2 of the GNU General Public License |
| * as published by the Free Software Foundation. |
| * |
| * Ethernet port config (0x00 is not present on IXP42X): |
| * |
| * logical port 0x00 0x10 0x20 |
| * NPE 0 (NPE-A) 1 (NPE-B) 2 (NPE-C) |
| * physical PortId 2 0 1 |
| * TX queue 23 24 25 |
| * RX-free queue 26 27 28 |
| * TX-done queue is always 31, per-port RX and TX-ready queues are configurable |
| * |
| * |
| * Queue entries: |
| * bits 0 -> 1 - NPE ID (RX and TX-done) |
| * bits 0 -> 2 - priority (TX, per 802.1D) |
| * bits 3 -> 4 - port ID (user-set?) |
| * bits 5 -> 31 - physical descriptor address |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/dmapool.h> |
| #include <linux/etherdevice.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/slab.h> |
| #include <mach/npe.h> |
| #include <mach/qmgr.h> |
| |
| #define DEBUG_DESC 0 |
| #define DEBUG_RX 0 |
| #define DEBUG_TX 0 |
| #define DEBUG_PKT_BYTES 0 |
| #define DEBUG_MDIO 0 |
| #define DEBUG_CLOSE 0 |
| |
| #define DRV_NAME "ixp4xx_eth" |
| |
| #define MAX_NPES 3 |
| |
| #define RX_DESCS 64 /* also length of all RX queues */ |
| #define TX_DESCS 16 /* also length of all TX queues */ |
| #define TXDONE_QUEUE_LEN 64 /* dwords */ |
| |
| #define POOL_ALLOC_SIZE (sizeof(struct desc) * (RX_DESCS + TX_DESCS)) |
| #define REGS_SIZE 0x1000 |
| #define MAX_MRU 1536 /* 0x600 */ |
| #define RX_BUFF_SIZE ALIGN((NET_IP_ALIGN) + MAX_MRU, 4) |
| |
| #define NAPI_WEIGHT 16 |
| #define MDIO_INTERVAL (3 * HZ) |
| #define MAX_MDIO_RETRIES 100 /* microseconds, typically 30 cycles */ |
| #define MAX_CLOSE_WAIT 1000 /* microseconds, typically 2-3 cycles */ |
| |
| #define NPE_ID(port_id) ((port_id) >> 4) |
| #define PHYSICAL_ID(port_id) ((NPE_ID(port_id) + 2) % 3) |
| #define TX_QUEUE(port_id) (NPE_ID(port_id) + 23) |
| #define RXFREE_QUEUE(port_id) (NPE_ID(port_id) + 26) |
| #define TXDONE_QUEUE 31 |
| |
| /* TX Control Registers */ |
| #define TX_CNTRL0_TX_EN 0x01 |
| #define TX_CNTRL0_HALFDUPLEX 0x02 |
| #define TX_CNTRL0_RETRY 0x04 |
| #define TX_CNTRL0_PAD_EN 0x08 |
| #define TX_CNTRL0_APPEND_FCS 0x10 |
| #define TX_CNTRL0_2DEFER 0x20 |
| #define TX_CNTRL0_RMII 0x40 /* reduced MII */ |
| #define TX_CNTRL1_RETRIES 0x0F /* 4 bits */ |
| |
| /* RX Control Registers */ |
| #define RX_CNTRL0_RX_EN 0x01 |
| #define RX_CNTRL0_PADSTRIP_EN 0x02 |
| #define RX_CNTRL0_SEND_FCS 0x04 |
| #define RX_CNTRL0_PAUSE_EN 0x08 |
| #define RX_CNTRL0_LOOP_EN 0x10 |
| #define RX_CNTRL0_ADDR_FLTR_EN 0x20 |
| #define RX_CNTRL0_RX_RUNT_EN 0x40 |
| #define RX_CNTRL0_BCAST_DIS 0x80 |
| #define RX_CNTRL1_DEFER_EN 0x01 |
| |
| /* Core Control Register */ |
| #define CORE_RESET 0x01 |
| #define CORE_RX_FIFO_FLUSH 0x02 |
| #define CORE_TX_FIFO_FLUSH 0x04 |
| #define CORE_SEND_JAM 0x08 |
| #define CORE_MDC_EN 0x10 /* MDIO using NPE-B ETH-0 only */ |
| |
| #define DEFAULT_TX_CNTRL0 (TX_CNTRL0_TX_EN | TX_CNTRL0_RETRY | \ |
| TX_CNTRL0_PAD_EN | TX_CNTRL0_APPEND_FCS | \ |
| TX_CNTRL0_2DEFER) |
| #define DEFAULT_RX_CNTRL0 RX_CNTRL0_RX_EN |
| #define DEFAULT_CORE_CNTRL CORE_MDC_EN |
| |
| |
| /* NPE message codes */ |
| #define NPE_GETSTATUS 0x00 |
| #define NPE_EDB_SETPORTADDRESS 0x01 |
| #define NPE_EDB_GETMACADDRESSDATABASE 0x02 |
| #define NPE_EDB_SETMACADDRESSSDATABASE 0x03 |
| #define NPE_GETSTATS 0x04 |
| #define NPE_RESETSTATS 0x05 |
| #define NPE_SETMAXFRAMELENGTHS 0x06 |
| #define NPE_VLAN_SETRXTAGMODE 0x07 |
| #define NPE_VLAN_SETDEFAULTRXVID 0x08 |
| #define NPE_VLAN_SETPORTVLANTABLEENTRY 0x09 |
| #define NPE_VLAN_SETPORTVLANTABLERANGE 0x0A |
| #define NPE_VLAN_SETRXQOSENTRY 0x0B |
| #define NPE_VLAN_SETPORTIDEXTRACTIONMODE 0x0C |
| #define NPE_STP_SETBLOCKINGSTATE 0x0D |
| #define NPE_FW_SETFIREWALLMODE 0x0E |
| #define NPE_PC_SETFRAMECONTROLDURATIONID 0x0F |
| #define NPE_PC_SETAPMACTABLE 0x11 |
| #define NPE_SETLOOPBACK_MODE 0x12 |
| #define NPE_PC_SETBSSIDTABLE 0x13 |
| #define NPE_ADDRESS_FILTER_CONFIG 0x14 |
| #define NPE_APPENDFCSCONFIG 0x15 |
| #define NPE_NOTIFY_MAC_RECOVERY_DONE 0x16 |
| #define NPE_MAC_RECOVERY_START 0x17 |
| |
| |
| #ifdef __ARMEB__ |
| typedef struct sk_buff buffer_t; |
| #define free_buffer dev_kfree_skb |
| #define free_buffer_irq dev_kfree_skb_irq |
| #else |
| typedef void buffer_t; |
| #define free_buffer kfree |
| #define free_buffer_irq kfree |
| #endif |
| |
| struct eth_regs { |
| u32 tx_control[2], __res1[2]; /* 000 */ |
| u32 rx_control[2], __res2[2]; /* 010 */ |
| u32 random_seed, __res3[3]; /* 020 */ |
| u32 partial_empty_threshold, __res4; /* 030 */ |
| u32 partial_full_threshold, __res5; /* 038 */ |
| u32 tx_start_bytes, __res6[3]; /* 040 */ |
| u32 tx_deferral, rx_deferral, __res7[2];/* 050 */ |
| u32 tx_2part_deferral[2], __res8[2]; /* 060 */ |
| u32 slot_time, __res9[3]; /* 070 */ |
| u32 mdio_command[4]; /* 080 */ |
| u32 mdio_status[4]; /* 090 */ |
| u32 mcast_mask[6], __res10[2]; /* 0A0 */ |
| u32 mcast_addr[6], __res11[2]; /* 0C0 */ |
| u32 int_clock_threshold, __res12[3]; /* 0E0 */ |
| u32 hw_addr[6], __res13[61]; /* 0F0 */ |
| u32 core_control; /* 1FC */ |
| }; |
| |
| struct port { |
| struct resource *mem_res; |
| struct eth_regs __iomem *regs; |
| struct npe *npe; |
| struct net_device *netdev; |
| struct napi_struct napi; |
| struct phy_device *phydev; |
| struct eth_plat_info *plat; |
| buffer_t *rx_buff_tab[RX_DESCS], *tx_buff_tab[TX_DESCS]; |
| struct desc *desc_tab; /* coherent */ |
| u32 desc_tab_phys; |
| int id; /* logical port ID */ |
| int speed, duplex; |
| u8 firmware[4]; |
| }; |
| |
| /* NPE message structure */ |
| struct msg { |
| #ifdef __ARMEB__ |
| u8 cmd, eth_id, byte2, byte3; |
| u8 byte4, byte5, byte6, byte7; |
| #else |
| u8 byte3, byte2, eth_id, cmd; |
| u8 byte7, byte6, byte5, byte4; |
| #endif |
| }; |
| |
| /* Ethernet packet descriptor */ |
| struct desc { |
| u32 next; /* pointer to next buffer, unused */ |
| |
| #ifdef __ARMEB__ |
| u16 buf_len; /* buffer length */ |
| u16 pkt_len; /* packet length */ |
| u32 data; /* pointer to data buffer in RAM */ |
| u8 dest_id; |
| u8 src_id; |
| u16 flags; |
| u8 qos; |
| u8 padlen; |
| u16 vlan_tci; |
| #else |
| u16 pkt_len; /* packet length */ |
| u16 buf_len; /* buffer length */ |
| u32 data; /* pointer to data buffer in RAM */ |
| u16 flags; |
| u8 src_id; |
| u8 dest_id; |
| u16 vlan_tci; |
| u8 padlen; |
| u8 qos; |
| #endif |
| |
| #ifdef __ARMEB__ |
| u8 dst_mac_0, dst_mac_1, dst_mac_2, dst_mac_3; |
| u8 dst_mac_4, dst_mac_5, src_mac_0, src_mac_1; |
| u8 src_mac_2, src_mac_3, src_mac_4, src_mac_5; |
| #else |
| u8 dst_mac_3, dst_mac_2, dst_mac_1, dst_mac_0; |
| u8 src_mac_1, src_mac_0, dst_mac_5, dst_mac_4; |
| u8 src_mac_5, src_mac_4, src_mac_3, src_mac_2; |
| #endif |
| }; |
| |
| |
| #define rx_desc_phys(port, n) ((port)->desc_tab_phys + \ |
| (n) * sizeof(struct desc)) |
| #define rx_desc_ptr(port, n) (&(port)->desc_tab[n]) |
| |
| #define tx_desc_phys(port, n) ((port)->desc_tab_phys + \ |
| ((n) + RX_DESCS) * sizeof(struct desc)) |
| #define tx_desc_ptr(port, n) (&(port)->desc_tab[(n) + RX_DESCS]) |
| |
| #ifndef __ARMEB__ |
| static inline void memcpy_swab32(u32 *dest, u32 *src, int cnt) |
| { |
| int i; |
| for (i = 0; i < cnt; i++) |
| dest[i] = swab32(src[i]); |
| } |
| #endif |
| |
| static spinlock_t mdio_lock; |
| static struct eth_regs __iomem *mdio_regs; /* mdio command and status only */ |
| struct mii_bus *mdio_bus; |
| static int ports_open; |
| static struct port *npe_port_tab[MAX_NPES]; |
| static struct dma_pool *dma_pool; |
| |
| |
| static int ixp4xx_mdio_cmd(struct mii_bus *bus, int phy_id, int location, |
| int write, u16 cmd) |
| { |
| int cycles = 0; |
| |
| if (__raw_readl(&mdio_regs->mdio_command[3]) & 0x80) { |
| printk(KERN_ERR "%s: MII not ready to transmit\n", bus->name); |
| return -1; |
| } |
| |
| if (write) { |
| __raw_writel(cmd & 0xFF, &mdio_regs->mdio_command[0]); |
| __raw_writel(cmd >> 8, &mdio_regs->mdio_command[1]); |
| } |
| __raw_writel(((phy_id << 5) | location) & 0xFF, |
| &mdio_regs->mdio_command[2]); |
| __raw_writel((phy_id >> 3) | (write << 2) | 0x80 /* GO */, |
| &mdio_regs->mdio_command[3]); |
| |
| while ((cycles < MAX_MDIO_RETRIES) && |
| (__raw_readl(&mdio_regs->mdio_command[3]) & 0x80)) { |
| udelay(1); |
| cycles++; |
| } |
| |
| if (cycles == MAX_MDIO_RETRIES) { |
| printk(KERN_ERR "%s #%i: MII write failed\n", bus->name, |
| phy_id); |
| return -1; |
| } |
| |
| #if DEBUG_MDIO |
| printk(KERN_DEBUG "%s #%i: mdio_%s() took %i cycles\n", bus->name, |
| phy_id, write ? "write" : "read", cycles); |
| #endif |
| |
| if (write) |
| return 0; |
| |
| if (__raw_readl(&mdio_regs->mdio_status[3]) & 0x80) { |
| #if DEBUG_MDIO |
| printk(KERN_DEBUG "%s #%i: MII read failed\n", bus->name, |
| phy_id); |
| #endif |
| return 0xFFFF; /* don't return error */ |
| } |
| |
| return (__raw_readl(&mdio_regs->mdio_status[0]) & 0xFF) | |
| ((__raw_readl(&mdio_regs->mdio_status[1]) & 0xFF) << 8); |
| } |
| |
| static int ixp4xx_mdio_read(struct mii_bus *bus, int phy_id, int location) |
| { |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&mdio_lock, flags); |
| ret = ixp4xx_mdio_cmd(bus, phy_id, location, 0, 0); |
| spin_unlock_irqrestore(&mdio_lock, flags); |
| #if DEBUG_MDIO |
| printk(KERN_DEBUG "%s #%i: MII read [%i] -> 0x%X\n", bus->name, |
| phy_id, location, ret); |
| #endif |
| return ret; |
| } |
| |
| static int ixp4xx_mdio_write(struct mii_bus *bus, int phy_id, int location, |
| u16 val) |
| { |
| unsigned long flags; |
| int ret; |
| |
| spin_lock_irqsave(&mdio_lock, flags); |
| ret = ixp4xx_mdio_cmd(bus, phy_id, location, 1, val); |
| spin_unlock_irqrestore(&mdio_lock, flags); |
| #if DEBUG_MDIO |
| printk(KERN_DEBUG "%s #%i: MII write [%i] <- 0x%X, err = %i\n", |
| bus->name, phy_id, location, val, ret); |
| #endif |
| return ret; |
| } |
| |
| static int ixp4xx_mdio_register(void) |
| { |
| int err; |
| |
| if (!(mdio_bus = mdiobus_alloc())) |
| return -ENOMEM; |
| |
| if (cpu_is_ixp43x()) { |
| /* IXP43x lacks NPE-B and uses NPE-C for MII PHY access */ |
| if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEC_ETH)) |
| return -ENODEV; |
| mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthC_BASE_VIRT; |
| } else { |
| /* All MII PHY accesses use NPE-B Ethernet registers */ |
| if (!(ixp4xx_read_feature_bits() & IXP4XX_FEATURE_NPEB_ETH0)) |
| return -ENODEV; |
| mdio_regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT; |
| } |
| |
| __raw_writel(DEFAULT_CORE_CNTRL, &mdio_regs->core_control); |
| spin_lock_init(&mdio_lock); |
| mdio_bus->name = "IXP4xx MII Bus"; |
| mdio_bus->read = &ixp4xx_mdio_read; |
| mdio_bus->write = &ixp4xx_mdio_write; |
| strcpy(mdio_bus->id, "0"); |
| |
| if ((err = mdiobus_register(mdio_bus))) |
| mdiobus_free(mdio_bus); |
| return err; |
| } |
| |
| static void ixp4xx_mdio_remove(void) |
| { |
| mdiobus_unregister(mdio_bus); |
| mdiobus_free(mdio_bus); |
| } |
| |
| |
| static void ixp4xx_adjust_link(struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| struct phy_device *phydev = port->phydev; |
| |
| if (!phydev->link) { |
| if (port->speed) { |
| port->speed = 0; |
| printk(KERN_INFO "%s: link down\n", dev->name); |
| } |
| return; |
| } |
| |
| if (port->speed == phydev->speed && port->duplex == phydev->duplex) |
| return; |
| |
| port->speed = phydev->speed; |
| port->duplex = phydev->duplex; |
| |
| if (port->duplex) |
| __raw_writel(DEFAULT_TX_CNTRL0 & ~TX_CNTRL0_HALFDUPLEX, |
| &port->regs->tx_control[0]); |
| else |
| __raw_writel(DEFAULT_TX_CNTRL0 | TX_CNTRL0_HALFDUPLEX, |
| &port->regs->tx_control[0]); |
| |
| printk(KERN_INFO "%s: link up, speed %u Mb/s, %s duplex\n", |
| dev->name, port->speed, port->duplex ? "full" : "half"); |
| } |
| |
| |
| static inline void debug_pkt(struct net_device *dev, const char *func, |
| u8 *data, int len) |
| { |
| #if DEBUG_PKT_BYTES |
| int i; |
| |
| printk(KERN_DEBUG "%s: %s(%i) ", dev->name, func, len); |
| for (i = 0; i < len; i++) { |
| if (i >= DEBUG_PKT_BYTES) |
| break; |
| printk("%s%02X", |
| ((i == 6) || (i == 12) || (i >= 14)) ? " " : "", |
| data[i]); |
| } |
| printk("\n"); |
| #endif |
| } |
| |
| |
| static inline void debug_desc(u32 phys, struct desc *desc) |
| { |
| #if DEBUG_DESC |
| printk(KERN_DEBUG "%X: %X %3X %3X %08X %2X < %2X %4X %X" |
| " %X %X %02X%02X%02X%02X%02X%02X < %02X%02X%02X%02X%02X%02X\n", |
| phys, desc->next, desc->buf_len, desc->pkt_len, |
| desc->data, desc->dest_id, desc->src_id, desc->flags, |
| desc->qos, desc->padlen, desc->vlan_tci, |
| desc->dst_mac_0, desc->dst_mac_1, desc->dst_mac_2, |
| desc->dst_mac_3, desc->dst_mac_4, desc->dst_mac_5, |
| desc->src_mac_0, desc->src_mac_1, desc->src_mac_2, |
| desc->src_mac_3, desc->src_mac_4, desc->src_mac_5); |
| #endif |
| } |
| |
| static inline int queue_get_desc(unsigned int queue, struct port *port, |
| int is_tx) |
| { |
| u32 phys, tab_phys, n_desc; |
| struct desc *tab; |
| |
| if (!(phys = qmgr_get_entry(queue))) |
| return -1; |
| |
| phys &= ~0x1F; /* mask out non-address bits */ |
| tab_phys = is_tx ? tx_desc_phys(port, 0) : rx_desc_phys(port, 0); |
| tab = is_tx ? tx_desc_ptr(port, 0) : rx_desc_ptr(port, 0); |
| n_desc = (phys - tab_phys) / sizeof(struct desc); |
| BUG_ON(n_desc >= (is_tx ? TX_DESCS : RX_DESCS)); |
| debug_desc(phys, &tab[n_desc]); |
| BUG_ON(tab[n_desc].next); |
| return n_desc; |
| } |
| |
| static inline void queue_put_desc(unsigned int queue, u32 phys, |
| struct desc *desc) |
| { |
| debug_desc(phys, desc); |
| BUG_ON(phys & 0x1F); |
| qmgr_put_entry(queue, phys); |
| /* Don't check for queue overflow here, we've allocated sufficient |
| length and queues >= 32 don't support this check anyway. */ |
| } |
| |
| |
| static inline void dma_unmap_tx(struct port *port, struct desc *desc) |
| { |
| #ifdef __ARMEB__ |
| dma_unmap_single(&port->netdev->dev, desc->data, |
| desc->buf_len, DMA_TO_DEVICE); |
| #else |
| dma_unmap_single(&port->netdev->dev, desc->data & ~3, |
| ALIGN((desc->data & 3) + desc->buf_len, 4), |
| DMA_TO_DEVICE); |
| #endif |
| } |
| |
| |
| static void eth_rx_irq(void *pdev) |
| { |
| struct net_device *dev = pdev; |
| struct port *port = netdev_priv(dev); |
| |
| #if DEBUG_RX |
| printk(KERN_DEBUG "%s: eth_rx_irq\n", dev->name); |
| #endif |
| qmgr_disable_irq(port->plat->rxq); |
| napi_schedule(&port->napi); |
| } |
| |
| static int eth_poll(struct napi_struct *napi, int budget) |
| { |
| struct port *port = container_of(napi, struct port, napi); |
| struct net_device *dev = port->netdev; |
| unsigned int rxq = port->plat->rxq, rxfreeq = RXFREE_QUEUE(port->id); |
| int received = 0; |
| |
| #if DEBUG_RX |
| printk(KERN_DEBUG "%s: eth_poll\n", dev->name); |
| #endif |
| |
| while (received < budget) { |
| struct sk_buff *skb; |
| struct desc *desc; |
| int n; |
| #ifdef __ARMEB__ |
| struct sk_buff *temp; |
| u32 phys; |
| #endif |
| |
| if ((n = queue_get_desc(rxq, port, 0)) < 0) { |
| #if DEBUG_RX |
| printk(KERN_DEBUG "%s: eth_poll napi_complete\n", |
| dev->name); |
| #endif |
| napi_complete(napi); |
| qmgr_enable_irq(rxq); |
| if (!qmgr_stat_below_low_watermark(rxq) && |
| napi_reschedule(napi)) { /* not empty again */ |
| #if DEBUG_RX |
| printk(KERN_DEBUG "%s: eth_poll" |
| " napi_reschedule successed\n", |
| dev->name); |
| #endif |
| qmgr_disable_irq(rxq); |
| continue; |
| } |
| #if DEBUG_RX |
| printk(KERN_DEBUG "%s: eth_poll all done\n", |
| dev->name); |
| #endif |
| return received; /* all work done */ |
| } |
| |
| desc = rx_desc_ptr(port, n); |
| |
| #ifdef __ARMEB__ |
| if ((skb = netdev_alloc_skb(dev, RX_BUFF_SIZE))) { |
| phys = dma_map_single(&dev->dev, skb->data, |
| RX_BUFF_SIZE, DMA_FROM_DEVICE); |
| if (dma_mapping_error(&dev->dev, phys)) { |
| dev_kfree_skb(skb); |
| skb = NULL; |
| } |
| } |
| #else |
| skb = netdev_alloc_skb(dev, |
| ALIGN(NET_IP_ALIGN + desc->pkt_len, 4)); |
| #endif |
| |
| if (!skb) { |
| dev->stats.rx_dropped++; |
| /* put the desc back on RX-ready queue */ |
| desc->buf_len = MAX_MRU; |
| desc->pkt_len = 0; |
| queue_put_desc(rxfreeq, rx_desc_phys(port, n), desc); |
| continue; |
| } |
| |
| /* process received frame */ |
| #ifdef __ARMEB__ |
| temp = skb; |
| skb = port->rx_buff_tab[n]; |
| dma_unmap_single(&dev->dev, desc->data - NET_IP_ALIGN, |
| RX_BUFF_SIZE, DMA_FROM_DEVICE); |
| #else |
| dma_sync_single_for_cpu(&dev->dev, desc->data - NET_IP_ALIGN, |
| RX_BUFF_SIZE, DMA_FROM_DEVICE); |
| memcpy_swab32((u32 *)skb->data, (u32 *)port->rx_buff_tab[n], |
| ALIGN(NET_IP_ALIGN + desc->pkt_len, 4) / 4); |
| #endif |
| skb_reserve(skb, NET_IP_ALIGN); |
| skb_put(skb, desc->pkt_len); |
| |
| debug_pkt(dev, "eth_poll", skb->data, skb->len); |
| |
| skb->protocol = eth_type_trans(skb, dev); |
| dev->stats.rx_packets++; |
| dev->stats.rx_bytes += skb->len; |
| netif_receive_skb(skb); |
| |
| /* put the new buffer on RX-free queue */ |
| #ifdef __ARMEB__ |
| port->rx_buff_tab[n] = temp; |
| desc->data = phys + NET_IP_ALIGN; |
| #endif |
| desc->buf_len = MAX_MRU; |
| desc->pkt_len = 0; |
| queue_put_desc(rxfreeq, rx_desc_phys(port, n), desc); |
| received++; |
| } |
| |
| #if DEBUG_RX |
| printk(KERN_DEBUG "eth_poll(): end, not all work done\n"); |
| #endif |
| return received; /* not all work done */ |
| } |
| |
| |
| static void eth_txdone_irq(void *unused) |
| { |
| u32 phys; |
| |
| #if DEBUG_TX |
| printk(KERN_DEBUG DRV_NAME ": eth_txdone_irq\n"); |
| #endif |
| while ((phys = qmgr_get_entry(TXDONE_QUEUE)) != 0) { |
| u32 npe_id, n_desc; |
| struct port *port; |
| struct desc *desc; |
| int start; |
| |
| npe_id = phys & 3; |
| BUG_ON(npe_id >= MAX_NPES); |
| port = npe_port_tab[npe_id]; |
| BUG_ON(!port); |
| phys &= ~0x1F; /* mask out non-address bits */ |
| n_desc = (phys - tx_desc_phys(port, 0)) / sizeof(struct desc); |
| BUG_ON(n_desc >= TX_DESCS); |
| desc = tx_desc_ptr(port, n_desc); |
| debug_desc(phys, desc); |
| |
| if (port->tx_buff_tab[n_desc]) { /* not the draining packet */ |
| port->netdev->stats.tx_packets++; |
| port->netdev->stats.tx_bytes += desc->pkt_len; |
| |
| dma_unmap_tx(port, desc); |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_txdone_irq free %p\n", |
| port->netdev->name, port->tx_buff_tab[n_desc]); |
| #endif |
| free_buffer_irq(port->tx_buff_tab[n_desc]); |
| port->tx_buff_tab[n_desc] = NULL; |
| } |
| |
| start = qmgr_stat_below_low_watermark(port->plat->txreadyq); |
| queue_put_desc(port->plat->txreadyq, phys, desc); |
| if (start) { /* TX-ready queue was empty */ |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_txdone_irq xmit ready\n", |
| port->netdev->name); |
| #endif |
| netif_wake_queue(port->netdev); |
| } |
| } |
| } |
| |
| static int eth_xmit(struct sk_buff *skb, struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| unsigned int txreadyq = port->plat->txreadyq; |
| int len, offset, bytes, n; |
| void *mem; |
| u32 phys; |
| struct desc *desc; |
| |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_xmit\n", dev->name); |
| #endif |
| |
| if (unlikely(skb->len > MAX_MRU)) { |
| dev_kfree_skb(skb); |
| dev->stats.tx_errors++; |
| return NETDEV_TX_OK; |
| } |
| |
| debug_pkt(dev, "eth_xmit", skb->data, skb->len); |
| |
| len = skb->len; |
| #ifdef __ARMEB__ |
| offset = 0; /* no need to keep alignment */ |
| bytes = len; |
| mem = skb->data; |
| #else |
| offset = (int)skb->data & 3; /* keep 32-bit alignment */ |
| bytes = ALIGN(offset + len, 4); |
| if (!(mem = kmalloc(bytes, GFP_ATOMIC))) { |
| dev_kfree_skb(skb); |
| dev->stats.tx_dropped++; |
| return NETDEV_TX_OK; |
| } |
| memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4); |
| dev_kfree_skb(skb); |
| #endif |
| |
| phys = dma_map_single(&dev->dev, mem, bytes, DMA_TO_DEVICE); |
| if (dma_mapping_error(&dev->dev, phys)) { |
| #ifdef __ARMEB__ |
| dev_kfree_skb(skb); |
| #else |
| kfree(mem); |
| #endif |
| dev->stats.tx_dropped++; |
| return NETDEV_TX_OK; |
| } |
| |
| n = queue_get_desc(txreadyq, port, 1); |
| BUG_ON(n < 0); |
| desc = tx_desc_ptr(port, n); |
| |
| #ifdef __ARMEB__ |
| port->tx_buff_tab[n] = skb; |
| #else |
| port->tx_buff_tab[n] = mem; |
| #endif |
| desc->data = phys + offset; |
| desc->buf_len = desc->pkt_len = len; |
| |
| /* NPE firmware pads short frames with zeros internally */ |
| wmb(); |
| queue_put_desc(TX_QUEUE(port->id), tx_desc_phys(port, n), desc); |
| dev->trans_start = jiffies; |
| |
| if (qmgr_stat_below_low_watermark(txreadyq)) { /* empty */ |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_xmit queue full\n", dev->name); |
| #endif |
| netif_stop_queue(dev); |
| /* we could miss TX ready interrupt */ |
| /* really empty in fact */ |
| if (!qmgr_stat_below_low_watermark(txreadyq)) { |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_xmit ready again\n", |
| dev->name); |
| #endif |
| netif_wake_queue(dev); |
| } |
| } |
| |
| #if DEBUG_TX |
| printk(KERN_DEBUG "%s: eth_xmit end\n", dev->name); |
| #endif |
| return NETDEV_TX_OK; |
| } |
| |
| |
| static void eth_set_mcast_list(struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| struct netdev_hw_addr *ha; |
| u8 diffs[ETH_ALEN], *addr; |
| int i; |
| |
| if ((dev->flags & IFF_PROMISC) || netdev_mc_empty(dev)) { |
| __raw_writel(DEFAULT_RX_CNTRL0 & ~RX_CNTRL0_ADDR_FLTR_EN, |
| &port->regs->rx_control[0]); |
| return; |
| } |
| |
| memset(diffs, 0, ETH_ALEN); |
| |
| addr = NULL; |
| netdev_for_each_mc_addr(ha, dev) { |
| if (!addr) |
| addr = ha->addr; /* first MAC address */ |
| for (i = 0; i < ETH_ALEN; i++) |
| diffs[i] |= addr[i] ^ ha->addr[i]; |
| } |
| |
| for (i = 0; i < ETH_ALEN; i++) { |
| __raw_writel(addr[i], &port->regs->mcast_addr[i]); |
| __raw_writel(~diffs[i], &port->regs->mcast_mask[i]); |
| } |
| |
| __raw_writel(DEFAULT_RX_CNTRL0 | RX_CNTRL0_ADDR_FLTR_EN, |
| &port->regs->rx_control[0]); |
| } |
| |
| |
| static int eth_ioctl(struct net_device *dev, struct ifreq *req, int cmd) |
| { |
| struct port *port = netdev_priv(dev); |
| |
| if (!netif_running(dev)) |
| return -EINVAL; |
| return phy_mii_ioctl(port->phydev, if_mii(req), cmd); |
| } |
| |
| /* ethtool support */ |
| |
| static void ixp4xx_get_drvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| struct port *port = netdev_priv(dev); |
| strcpy(info->driver, DRV_NAME); |
| snprintf(info->fw_version, sizeof(info->fw_version), "%u:%u:%u:%u", |
| port->firmware[0], port->firmware[1], |
| port->firmware[2], port->firmware[3]); |
| strcpy(info->bus_info, "internal"); |
| } |
| |
| static int ixp4xx_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct port *port = netdev_priv(dev); |
| return phy_ethtool_gset(port->phydev, cmd); |
| } |
| |
| static int ixp4xx_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) |
| { |
| struct port *port = netdev_priv(dev); |
| return phy_ethtool_sset(port->phydev, cmd); |
| } |
| |
| static int ixp4xx_nway_reset(struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| return phy_start_aneg(port->phydev); |
| } |
| |
| static const struct ethtool_ops ixp4xx_ethtool_ops = { |
| .get_drvinfo = ixp4xx_get_drvinfo, |
| .get_settings = ixp4xx_get_settings, |
| .set_settings = ixp4xx_set_settings, |
| .nway_reset = ixp4xx_nway_reset, |
| .get_link = ethtool_op_get_link, |
| }; |
| |
| |
| static int request_queues(struct port *port) |
| { |
| int err; |
| |
| err = qmgr_request_queue(RXFREE_QUEUE(port->id), RX_DESCS, 0, 0, |
| "%s:RX-free", port->netdev->name); |
| if (err) |
| return err; |
| |
| err = qmgr_request_queue(port->plat->rxq, RX_DESCS, 0, 0, |
| "%s:RX", port->netdev->name); |
| if (err) |
| goto rel_rxfree; |
| |
| err = qmgr_request_queue(TX_QUEUE(port->id), TX_DESCS, 0, 0, |
| "%s:TX", port->netdev->name); |
| if (err) |
| goto rel_rx; |
| |
| err = qmgr_request_queue(port->plat->txreadyq, TX_DESCS, 0, 0, |
| "%s:TX-ready", port->netdev->name); |
| if (err) |
| goto rel_tx; |
| |
| /* TX-done queue handles skbs sent out by the NPEs */ |
| if (!ports_open) { |
| err = qmgr_request_queue(TXDONE_QUEUE, TXDONE_QUEUE_LEN, 0, 0, |
| "%s:TX-done", DRV_NAME); |
| if (err) |
| goto rel_txready; |
| } |
| return 0; |
| |
| rel_txready: |
| qmgr_release_queue(port->plat->txreadyq); |
| rel_tx: |
| qmgr_release_queue(TX_QUEUE(port->id)); |
| rel_rx: |
| qmgr_release_queue(port->plat->rxq); |
| rel_rxfree: |
| qmgr_release_queue(RXFREE_QUEUE(port->id)); |
| printk(KERN_DEBUG "%s: unable to request hardware queues\n", |
| port->netdev->name); |
| return err; |
| } |
| |
| static void release_queues(struct port *port) |
| { |
| qmgr_release_queue(RXFREE_QUEUE(port->id)); |
| qmgr_release_queue(port->plat->rxq); |
| qmgr_release_queue(TX_QUEUE(port->id)); |
| qmgr_release_queue(port->plat->txreadyq); |
| |
| if (!ports_open) |
| qmgr_release_queue(TXDONE_QUEUE); |
| } |
| |
| static int init_queues(struct port *port) |
| { |
| int i; |
| |
| if (!ports_open) |
| if (!(dma_pool = dma_pool_create(DRV_NAME, NULL, |
| POOL_ALLOC_SIZE, 32, 0))) |
| return -ENOMEM; |
| |
| if (!(port->desc_tab = dma_pool_alloc(dma_pool, GFP_KERNEL, |
| &port->desc_tab_phys))) |
| return -ENOMEM; |
| memset(port->desc_tab, 0, POOL_ALLOC_SIZE); |
| memset(port->rx_buff_tab, 0, sizeof(port->rx_buff_tab)); /* tables */ |
| memset(port->tx_buff_tab, 0, sizeof(port->tx_buff_tab)); |
| |
| /* Setup RX buffers */ |
| for (i = 0; i < RX_DESCS; i++) { |
| struct desc *desc = rx_desc_ptr(port, i); |
| buffer_t *buff; /* skb or kmalloc()ated memory */ |
| void *data; |
| #ifdef __ARMEB__ |
| if (!(buff = netdev_alloc_skb(port->netdev, RX_BUFF_SIZE))) |
| return -ENOMEM; |
| data = buff->data; |
| #else |
| if (!(buff = kmalloc(RX_BUFF_SIZE, GFP_KERNEL))) |
| return -ENOMEM; |
| data = buff; |
| #endif |
| desc->buf_len = MAX_MRU; |
| desc->data = dma_map_single(&port->netdev->dev, data, |
| RX_BUFF_SIZE, DMA_FROM_DEVICE); |
| if (dma_mapping_error(&port->netdev->dev, desc->data)) { |
| free_buffer(buff); |
| return -EIO; |
| } |
| desc->data += NET_IP_ALIGN; |
| port->rx_buff_tab[i] = buff; |
| } |
| |
| return 0; |
| } |
| |
| static void destroy_queues(struct port *port) |
| { |
| int i; |
| |
| if (port->desc_tab) { |
| for (i = 0; i < RX_DESCS; i++) { |
| struct desc *desc = rx_desc_ptr(port, i); |
| buffer_t *buff = port->rx_buff_tab[i]; |
| if (buff) { |
| dma_unmap_single(&port->netdev->dev, |
| desc->data - NET_IP_ALIGN, |
| RX_BUFF_SIZE, DMA_FROM_DEVICE); |
| free_buffer(buff); |
| } |
| } |
| for (i = 0; i < TX_DESCS; i++) { |
| struct desc *desc = tx_desc_ptr(port, i); |
| buffer_t *buff = port->tx_buff_tab[i]; |
| if (buff) { |
| dma_unmap_tx(port, desc); |
| free_buffer(buff); |
| } |
| } |
| dma_pool_free(dma_pool, port->desc_tab, port->desc_tab_phys); |
| port->desc_tab = NULL; |
| } |
| |
| if (!ports_open && dma_pool) { |
| dma_pool_destroy(dma_pool); |
| dma_pool = NULL; |
| } |
| } |
| |
| static int eth_open(struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| struct npe *npe = port->npe; |
| struct msg msg; |
| int i, err; |
| |
| if (!npe_running(npe)) { |
| err = npe_load_firmware(npe, npe_name(npe), &dev->dev); |
| if (err) |
| return err; |
| |
| if (npe_recv_message(npe, &msg, "ETH_GET_STATUS")) { |
| printk(KERN_ERR "%s: %s not responding\n", dev->name, |
| npe_name(npe)); |
| return -EIO; |
| } |
| port->firmware[0] = msg.byte4; |
| port->firmware[1] = msg.byte5; |
| port->firmware[2] = msg.byte6; |
| port->firmware[3] = msg.byte7; |
| } |
| |
| memset(&msg, 0, sizeof(msg)); |
| msg.cmd = NPE_VLAN_SETRXQOSENTRY; |
| msg.eth_id = port->id; |
| msg.byte5 = port->plat->rxq | 0x80; |
| msg.byte7 = port->plat->rxq << 4; |
| for (i = 0; i < 8; i++) { |
| msg.byte3 = i; |
| if (npe_send_recv_message(port->npe, &msg, "ETH_SET_RXQ")) |
| return -EIO; |
| } |
| |
| msg.cmd = NPE_EDB_SETPORTADDRESS; |
| msg.eth_id = PHYSICAL_ID(port->id); |
| msg.byte2 = dev->dev_addr[0]; |
| msg.byte3 = dev->dev_addr[1]; |
| msg.byte4 = dev->dev_addr[2]; |
| msg.byte5 = dev->dev_addr[3]; |
| msg.byte6 = dev->dev_addr[4]; |
| msg.byte7 = dev->dev_addr[5]; |
| if (npe_send_recv_message(port->npe, &msg, "ETH_SET_MAC")) |
| return -EIO; |
| |
| memset(&msg, 0, sizeof(msg)); |
| msg.cmd = NPE_FW_SETFIREWALLMODE; |
| msg.eth_id = port->id; |
| if (npe_send_recv_message(port->npe, &msg, "ETH_SET_FIREWALL_MODE")) |
| return -EIO; |
| |
| if ((err = request_queues(port)) != 0) |
| return err; |
| |
| if ((err = init_queues(port)) != 0) { |
| destroy_queues(port); |
| release_queues(port); |
| return err; |
| } |
| |
| port->speed = 0; /* force "link up" message */ |
| phy_start(port->phydev); |
| |
| for (i = 0; i < ETH_ALEN; i++) |
| __raw_writel(dev->dev_addr[i], &port->regs->hw_addr[i]); |
| __raw_writel(0x08, &port->regs->random_seed); |
| __raw_writel(0x12, &port->regs->partial_empty_threshold); |
| __raw_writel(0x30, &port->regs->partial_full_threshold); |
| __raw_writel(0x08, &port->regs->tx_start_bytes); |
| __raw_writel(0x15, &port->regs->tx_deferral); |
| __raw_writel(0x08, &port->regs->tx_2part_deferral[0]); |
| __raw_writel(0x07, &port->regs->tx_2part_deferral[1]); |
| __raw_writel(0x80, &port->regs->slot_time); |
| __raw_writel(0x01, &port->regs->int_clock_threshold); |
| |
| /* Populate queues with buffers, no failure after this point */ |
| for (i = 0; i < TX_DESCS; i++) |
| queue_put_desc(port->plat->txreadyq, |
| tx_desc_phys(port, i), tx_desc_ptr(port, i)); |
| |
| for (i = 0; i < RX_DESCS; i++) |
| queue_put_desc(RXFREE_QUEUE(port->id), |
| rx_desc_phys(port, i), rx_desc_ptr(port, i)); |
| |
| __raw_writel(TX_CNTRL1_RETRIES, &port->regs->tx_control[1]); |
| __raw_writel(DEFAULT_TX_CNTRL0, &port->regs->tx_control[0]); |
| __raw_writel(0, &port->regs->rx_control[1]); |
| __raw_writel(DEFAULT_RX_CNTRL0, &port->regs->rx_control[0]); |
| |
| napi_enable(&port->napi); |
| eth_set_mcast_list(dev); |
| netif_start_queue(dev); |
| |
| qmgr_set_irq(port->plat->rxq, QUEUE_IRQ_SRC_NOT_EMPTY, |
| eth_rx_irq, dev); |
| if (!ports_open) { |
| qmgr_set_irq(TXDONE_QUEUE, QUEUE_IRQ_SRC_NOT_EMPTY, |
| eth_txdone_irq, NULL); |
| qmgr_enable_irq(TXDONE_QUEUE); |
| } |
| ports_open++; |
| /* we may already have RX data, enables IRQ */ |
| napi_schedule(&port->napi); |
| return 0; |
| } |
| |
| static int eth_close(struct net_device *dev) |
| { |
| struct port *port = netdev_priv(dev); |
| struct msg msg; |
| int buffs = RX_DESCS; /* allocated RX buffers */ |
| int i; |
| |
| ports_open--; |
| qmgr_disable_irq(port->plat->rxq); |
| napi_disable(&port->napi); |
| netif_stop_queue(dev); |
| |
| while (queue_get_desc(RXFREE_QUEUE(port->id), port, 0) >= 0) |
| buffs--; |
| |
| memset(&msg, 0, sizeof(msg)); |
| msg.cmd = NPE_SETLOOPBACK_MODE; |
| msg.eth_id = port->id; |
| msg.byte3 = 1; |
| if (npe_send_recv_message(port->npe, &msg, "ETH_ENABLE_LOOPBACK")) |
| printk(KERN_CRIT "%s: unable to enable loopback\n", dev->name); |
| |
| i = 0; |
| do { /* drain RX buffers */ |
| while (queue_get_desc(port->plat->rxq, port, 0) >= 0) |
| buffs--; |
| if (!buffs) |
| break; |
| if (qmgr_stat_empty(TX_QUEUE(port->id))) { |
| /* we have to inject some packet */ |
| struct desc *desc; |
| u32 phys; |
| int n = queue_get_desc(port->plat->txreadyq, port, 1); |
| BUG_ON(n < 0); |
| desc = tx_desc_ptr(port, n); |
| phys = tx_desc_phys(port, n); |
| desc->buf_len = desc->pkt_len = 1; |
| wmb(); |
| queue_put_desc(TX_QUEUE(port->id), phys, desc); |
| } |
| udelay(1); |
| } while (++i < MAX_CLOSE_WAIT); |
| |
| if (buffs) |
| printk(KERN_CRIT "%s: unable to drain RX queue, %i buffer(s)" |
| " left in NPE\n", dev->name, buffs); |
| #if DEBUG_CLOSE |
| if (!buffs) |
| printk(KERN_DEBUG "Draining RX queue took %i cycles\n", i); |
| #endif |
| |
| buffs = TX_DESCS; |
| while (queue_get_desc(TX_QUEUE(port->id), port, 1) >= 0) |
| buffs--; /* cancel TX */ |
| |
| i = 0; |
| do { |
| while (queue_get_desc(port->plat->txreadyq, port, 1) >= 0) |
| buffs--; |
| if (!buffs) |
| break; |
| } while (++i < MAX_CLOSE_WAIT); |
| |
| if (buffs) |
| printk(KERN_CRIT "%s: unable to drain TX queue, %i buffer(s) " |
| "left in NPE\n", dev->name, buffs); |
| #if DEBUG_CLOSE |
| if (!buffs) |
| printk(KERN_DEBUG "Draining TX queues took %i cycles\n", i); |
| #endif |
| |
| msg.byte3 = 0; |
| if (npe_send_recv_message(port->npe, &msg, "ETH_DISABLE_LOOPBACK")) |
| printk(KERN_CRIT "%s: unable to disable loopback\n", |
| dev->name); |
| |
| phy_stop(port->phydev); |
| |
| if (!ports_open) |
| qmgr_disable_irq(TXDONE_QUEUE); |
| destroy_queues(port); |
| release_queues(port); |
| return 0; |
| } |
| |
| static const struct net_device_ops ixp4xx_netdev_ops = { |
| .ndo_open = eth_open, |
| .ndo_stop = eth_close, |
| .ndo_start_xmit = eth_xmit, |
| .ndo_set_multicast_list = eth_set_mcast_list, |
| .ndo_do_ioctl = eth_ioctl, |
| .ndo_change_mtu = eth_change_mtu, |
| .ndo_set_mac_address = eth_mac_addr, |
| .ndo_validate_addr = eth_validate_addr, |
| }; |
| |
| static int __devinit eth_init_one(struct platform_device *pdev) |
| { |
| struct port *port; |
| struct net_device *dev; |
| struct eth_plat_info *plat = pdev->dev.platform_data; |
| u32 regs_phys; |
| char phy_id[MII_BUS_ID_SIZE + 3]; |
| int err; |
| |
| if (!(dev = alloc_etherdev(sizeof(struct port)))) |
| return -ENOMEM; |
| |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| port = netdev_priv(dev); |
| port->netdev = dev; |
| port->id = pdev->id; |
| |
| switch (port->id) { |
| case IXP4XX_ETH_NPEA: |
| port->regs = (struct eth_regs __iomem *)IXP4XX_EthA_BASE_VIRT; |
| regs_phys = IXP4XX_EthA_BASE_PHYS; |
| break; |
| case IXP4XX_ETH_NPEB: |
| port->regs = (struct eth_regs __iomem *)IXP4XX_EthB_BASE_VIRT; |
| regs_phys = IXP4XX_EthB_BASE_PHYS; |
| break; |
| case IXP4XX_ETH_NPEC: |
| port->regs = (struct eth_regs __iomem *)IXP4XX_EthC_BASE_VIRT; |
| regs_phys = IXP4XX_EthC_BASE_PHYS; |
| break; |
| default: |
| err = -ENODEV; |
| goto err_free; |
| } |
| |
| dev->netdev_ops = &ixp4xx_netdev_ops; |
| dev->ethtool_ops = &ixp4xx_ethtool_ops; |
| dev->tx_queue_len = 100; |
| |
| netif_napi_add(dev, &port->napi, eth_poll, NAPI_WEIGHT); |
| |
| if (!(port->npe = npe_request(NPE_ID(port->id)))) { |
| err = -EIO; |
| goto err_free; |
| } |
| |
| port->mem_res = request_mem_region(regs_phys, REGS_SIZE, dev->name); |
| if (!port->mem_res) { |
| err = -EBUSY; |
| goto err_npe_rel; |
| } |
| |
| port->plat = plat; |
| npe_port_tab[NPE_ID(port->id)] = port; |
| memcpy(dev->dev_addr, plat->hwaddr, ETH_ALEN); |
| |
| platform_set_drvdata(pdev, dev); |
| |
| __raw_writel(DEFAULT_CORE_CNTRL | CORE_RESET, |
| &port->regs->core_control); |
| udelay(50); |
| __raw_writel(DEFAULT_CORE_CNTRL, &port->regs->core_control); |
| udelay(50); |
| |
| snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, "0", plat->phy); |
| port->phydev = phy_connect(dev, phy_id, &ixp4xx_adjust_link, 0, |
| PHY_INTERFACE_MODE_MII); |
| if ((err = IS_ERR(port->phydev))) |
| goto err_free_mem; |
| |
| port->phydev->irq = PHY_POLL; |
| |
| if ((err = register_netdev(dev))) |
| goto err_phy_dis; |
| |
| printk(KERN_INFO "%s: MII PHY %i on %s\n", dev->name, plat->phy, |
| npe_name(port->npe)); |
| |
| return 0; |
| |
| err_phy_dis: |
| phy_disconnect(port->phydev); |
| err_free_mem: |
| npe_port_tab[NPE_ID(port->id)] = NULL; |
| platform_set_drvdata(pdev, NULL); |
| release_resource(port->mem_res); |
| err_npe_rel: |
| npe_release(port->npe); |
| err_free: |
| free_netdev(dev); |
| return err; |
| } |
| |
| static int __devexit eth_remove_one(struct platform_device *pdev) |
| { |
| struct net_device *dev = platform_get_drvdata(pdev); |
| struct port *port = netdev_priv(dev); |
| |
| unregister_netdev(dev); |
| phy_disconnect(port->phydev); |
| npe_port_tab[NPE_ID(port->id)] = NULL; |
| platform_set_drvdata(pdev, NULL); |
| npe_release(port->npe); |
| release_resource(port->mem_res); |
| free_netdev(dev); |
| return 0; |
| } |
| |
| static struct platform_driver ixp4xx_eth_driver = { |
| .driver.name = DRV_NAME, |
| .probe = eth_init_one, |
| .remove = eth_remove_one, |
| }; |
| |
| static int __init eth_init_module(void) |
| { |
| int err; |
| if ((err = ixp4xx_mdio_register())) |
| return err; |
| return platform_driver_register(&ixp4xx_eth_driver); |
| } |
| |
| static void __exit eth_cleanup_module(void) |
| { |
| platform_driver_unregister(&ixp4xx_eth_driver); |
| ixp4xx_mdio_remove(); |
| } |
| |
| MODULE_AUTHOR("Krzysztof Halasa"); |
| MODULE_DESCRIPTION("Intel IXP4xx Ethernet driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:ixp4xx_eth"); |
| module_init(eth_init_module); |
| module_exit(eth_cleanup_module); |