| /****************************************************************************** |
| * |
| * This file is provided under a dual BSD/GPLv2 license. When using or |
| * redistributing this file, you may do so under either license. |
| * |
| * GPL LICENSE SUMMARY |
| * |
| * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of version 2 of the GNU General Public License as |
| * published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU |
| * General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, |
| * USA |
| * |
| * The full GNU General Public License is included in this distribution |
| * in the file called LICENSE.GPL. |
| * |
| * Contact Information: |
| * James P. Ketrenos <ipw2100-admin@linux.intel.com> |
| * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 |
| * |
| * BSD LICENSE |
| * |
| * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. |
| * All rights reserved. |
| * |
| * Redistribution and use in source and binary forms, with or without |
| * modification, are permitted provided that the following conditions |
| * are met: |
| * |
| * * Redistributions of source code must retain the above copyright |
| * notice, this list of conditions and the following disclaimer. |
| * * Redistributions in binary form must reproduce the above copyright |
| * notice, this list of conditions and the following disclaimer in |
| * the documentation and/or other materials provided with the |
| * distribution. |
| * * Neither the name Intel Corporation nor the names of its |
| * contributors may be used to endorse or promote products derived |
| * from this software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS |
| * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT |
| * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR |
| * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT |
| * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, |
| * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT |
| * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, |
| * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY |
| * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| *****************************************************************************/ |
| |
| #ifndef __iwl_prph_h__ |
| #define __iwl_prph_h__ |
| |
| /* |
| * Registers in this file are internal, not PCI bus memory mapped. |
| * Driver accesses these via HBUS_TARG_PRPH_* registers. |
| */ |
| #define PRPH_BASE (0x00000) |
| #define PRPH_END (0xFFFFF) |
| |
| /* APMG (power management) constants */ |
| #define APMG_BASE (PRPH_BASE + 0x3000) |
| #define APMG_CLK_CTRL_REG (APMG_BASE + 0x0000) |
| #define APMG_CLK_EN_REG (APMG_BASE + 0x0004) |
| #define APMG_CLK_DIS_REG (APMG_BASE + 0x0008) |
| #define APMG_PS_CTRL_REG (APMG_BASE + 0x000c) |
| #define APMG_PCIDEV_STT_REG (APMG_BASE + 0x0010) |
| #define APMG_RFKILL_REG (APMG_BASE + 0x0014) |
| #define APMG_RTC_INT_STT_REG (APMG_BASE + 0x001c) |
| #define APMG_RTC_INT_MSK_REG (APMG_BASE + 0x0020) |
| |
| #define APMG_CLK_VAL_DMA_CLK_RQT (0x00000200) |
| #define APMG_CLK_VAL_BSM_CLK_RQT (0x00000800) |
| |
| #define APMG_PS_CTRL_VAL_RESET_REQ (0x04000000) |
| |
| #define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800) |
| |
| #define APMG_PS_CTRL_MSK_PWR_SRC (0x03000000) |
| #define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN (0x00000000) |
| #define APMG_PS_CTRL_VAL_PWR_SRC_VAUX (0x01000000) |
| |
| |
| /** |
| * BSM (Bootstrap State Machine) |
| * |
| * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program |
| * in special SRAM that does not power down when the embedded control |
| * processor is sleeping (e.g. for periodic power-saving shutdowns of radio). |
| * |
| * When powering back up after sleeps (or during initial uCode load), the BSM |
| * internally loads the short bootstrap program from the special SRAM into the |
| * embedded processor's instruction SRAM, and starts the processor so it runs |
| * the bootstrap program. |
| * |
| * This bootstrap program loads (via PCI busmaster DMA) instructions and data |
| * images for a uCode program from host DRAM locations. The host driver |
| * indicates DRAM locations and sizes for instruction and data images via the |
| * four BSM_DRAM_* registers. Once the bootstrap program loads the new program, |
| * the new program starts automatically. |
| * |
| * The uCode used for open-source drivers includes two programs: |
| * |
| * 1) Initialization -- performs hardware calibration and sets up some |
| * internal data, then notifies host via "initialize alive" notification |
| * (struct iwl_init_alive_resp) that it has completed all of its work. |
| * After signal from host, it then loads and starts the runtime program. |
| * The initialization program must be used when initially setting up the |
| * NIC after loading the driver. |
| * |
| * 2) Runtime/Protocol -- performs all normal runtime operations. This |
| * notifies host via "alive" notification (struct iwl_alive_resp) that it |
| * is ready to be used. |
| * |
| * When initializing the NIC, the host driver does the following procedure: |
| * |
| * 1) Load bootstrap program (instructions only, no data image for bootstrap) |
| * into bootstrap memory. Use dword writes starting at BSM_SRAM_LOWER_BOUND |
| * |
| * 2) Point (via BSM_DRAM_*) to the "initialize" uCode data and instruction |
| * images in host DRAM. |
| * |
| * 3) Set up BSM to copy from BSM SRAM into uCode instruction SRAM when asked: |
| * BSM_WR_MEM_SRC_REG = 0 |
| * BSM_WR_MEM_DST_REG = RTC_INST_LOWER_BOUND |
| * BSM_WR_MEM_DWCOUNT_REG = # dwords in bootstrap instruction image |
| * |
| * 4) Load bootstrap into instruction SRAM: |
| * BSM_WR_CTRL_REG = BSM_WR_CTRL_REG_BIT_START |
| * |
| * 5) Wait for load completion: |
| * Poll BSM_WR_CTRL_REG for BSM_WR_CTRL_REG_BIT_START = 0 |
| * |
| * 6) Enable future boot loads whenever NIC's power management triggers it: |
| * BSM_WR_CTRL_REG = BSM_WR_CTRL_REG_BIT_START_EN |
| * |
| * 7) Start the NIC by removing all reset bits: |
| * CSR_RESET = 0 |
| * |
| * The bootstrap uCode (already in instruction SRAM) loads initialization |
| * uCode. Initialization uCode performs data initialization, sends |
| * "initialize alive" notification to host, and waits for a signal from |
| * host to load runtime code. |
| * |
| * 4) Point (via BSM_DRAM_*) to the "runtime" uCode data and instruction |
| * images in host DRAM. The last register loaded must be the instruction |
| * bytecount register ("1" in MSbit tells initialization uCode to load |
| * the runtime uCode): |
| * BSM_DRAM_INST_BYTECOUNT_REG = bytecount | BSM_DRAM_INST_LOAD |
| * |
| * 5) Wait for "alive" notification, then issue normal runtime commands. |
| * |
| * Data caching during power-downs: |
| * |
| * Just before the embedded controller powers down (e.g for automatic |
| * power-saving modes, or for RFKILL), uCode stores (via PCI busmaster DMA) |
| * a current snapshot of the embedded processor's data SRAM into host DRAM. |
| * This caches the data while the embedded processor's memory is powered down. |
| * Location and size are controlled by BSM_DRAM_DATA_* registers. |
| * |
| * NOTE: Instruction SRAM does not need to be saved, since that doesn't |
| * change during operation; the original image (from uCode distribution |
| * file) can be used for reload. |
| * |
| * When powering back up, the BSM loads the bootstrap program. Bootstrap looks |
| * at the BSM_DRAM_* registers, which now point to the runtime instruction |
| * image and the cached (modified) runtime data (*not* the initialization |
| * uCode). Bootstrap reloads these runtime images into SRAM, and restarts the |
| * uCode from where it left off before the power-down. |
| * |
| * NOTE: Initialization uCode does *not* run as part of the save/restore |
| * procedure. |
| * |
| * This save/restore method is mostly for autonomous power management during |
| * normal operation (result of POWER_TABLE_CMD). Platform suspend/resume and |
| * RFKILL should use complete restarts (with total re-initialization) of uCode, |
| * allowing total shutdown (including BSM memory). |
| * |
| * Note that, during normal operation, the host DRAM that held the initial |
| * startup data for the runtime code is now being used as a backup data cache |
| * for modified data! If you need to completely re-initialize the NIC, make |
| * sure that you use the runtime data image from the uCode distribution file, |
| * not the modified/saved runtime data. You may want to store a separate |
| * "clean" runtime data image in DRAM to avoid disk reads of distribution file. |
| */ |
| |
| /* BSM bit fields */ |
| #define BSM_WR_CTRL_REG_BIT_START (0x80000000) /* start boot load now */ |
| #define BSM_WR_CTRL_REG_BIT_START_EN (0x40000000) /* enable boot after pwrup*/ |
| #define BSM_DRAM_INST_LOAD (0x80000000) /* start program load now */ |
| |
| /* BSM addresses */ |
| #define BSM_BASE (PRPH_BASE + 0x3400) |
| #define BSM_END (PRPH_BASE + 0x3800) |
| |
| #define BSM_WR_CTRL_REG (BSM_BASE + 0x000) /* ctl and status */ |
| #define BSM_WR_MEM_SRC_REG (BSM_BASE + 0x004) /* source in BSM mem */ |
| #define BSM_WR_MEM_DST_REG (BSM_BASE + 0x008) /* dest in SRAM mem */ |
| #define BSM_WR_DWCOUNT_REG (BSM_BASE + 0x00C) /* bytes */ |
| #define BSM_WR_STATUS_REG (BSM_BASE + 0x010) /* bit 0: 1 == done */ |
| |
| /* |
| * Pointers and size regs for bootstrap load and data SRAM save/restore. |
| * NOTE: 3945 pointers use bits 31:0 of DRAM address. |
| * 4965 pointers use bits 35:4 of DRAM address. |
| */ |
| #define BSM_DRAM_INST_PTR_REG (BSM_BASE + 0x090) |
| #define BSM_DRAM_INST_BYTECOUNT_REG (BSM_BASE + 0x094) |
| #define BSM_DRAM_DATA_PTR_REG (BSM_BASE + 0x098) |
| #define BSM_DRAM_DATA_BYTECOUNT_REG (BSM_BASE + 0x09C) |
| |
| /* |
| * BSM special memory, stays powered on during power-save sleeps. |
| * Read/write, address range from LOWER_BOUND to (LOWER_BOUND + SIZE -1) |
| */ |
| #define BSM_SRAM_LOWER_BOUND (PRPH_BASE + 0x3800) |
| #define BSM_SRAM_SIZE (1024) /* bytes */ |
| |
| |
| /* 3945 Tx scheduler registers */ |
| #define ALM_SCD_BASE (PRPH_BASE + 0x2E00) |
| #define ALM_SCD_MODE_REG (ALM_SCD_BASE + 0x000) |
| #define ALM_SCD_ARASTAT_REG (ALM_SCD_BASE + 0x004) |
| #define ALM_SCD_TXFACT_REG (ALM_SCD_BASE + 0x010) |
| #define ALM_SCD_TXF4MF_REG (ALM_SCD_BASE + 0x014) |
| #define ALM_SCD_TXF5MF_REG (ALM_SCD_BASE + 0x020) |
| #define ALM_SCD_SBYP_MODE_1_REG (ALM_SCD_BASE + 0x02C) |
| #define ALM_SCD_SBYP_MODE_2_REG (ALM_SCD_BASE + 0x030) |
| |
| /* |
| * 4965 Tx Scheduler registers. |
| * Details are documented in iwl-4965-hw.h |
| */ |
| #define KDR_SCD_BASE (PRPH_BASE + 0xa02c00) |
| |
| #define KDR_SCD_SRAM_BASE_ADDR (KDR_SCD_BASE + 0x0) |
| #define KDR_SCD_EMPTY_BITS (KDR_SCD_BASE + 0x4) |
| #define KDR_SCD_DRAM_BASE_ADDR (KDR_SCD_BASE + 0x10) |
| #define KDR_SCD_AIT (KDR_SCD_BASE + 0x18) |
| #define KDR_SCD_TXFACT (KDR_SCD_BASE + 0x1c) |
| #define KDR_SCD_QUEUE_WRPTR(x) (KDR_SCD_BASE + 0x24 + (x) * 4) |
| #define KDR_SCD_QUEUE_RDPTR(x) (KDR_SCD_BASE + 0x64 + (x) * 4) |
| #define KDR_SCD_SETQUEUENUM (KDR_SCD_BASE + 0xa4) |
| #define KDR_SCD_SET_TXSTAT_TXED (KDR_SCD_BASE + 0xa8) |
| #define KDR_SCD_SET_TXSTAT_DONE (KDR_SCD_BASE + 0xac) |
| #define KDR_SCD_SET_TXSTAT_NOT_SCHD (KDR_SCD_BASE + 0xb0) |
| #define KDR_SCD_DECREASE_CREDIT (KDR_SCD_BASE + 0xb4) |
| #define KDR_SCD_DECREASE_SCREDIT (KDR_SCD_BASE + 0xb8) |
| #define KDR_SCD_LOAD_CREDIT (KDR_SCD_BASE + 0xbc) |
| #define KDR_SCD_LOAD_SCREDIT (KDR_SCD_BASE + 0xc0) |
| #define KDR_SCD_BAR (KDR_SCD_BASE + 0xc4) |
| #define KDR_SCD_BAR_DW0 (KDR_SCD_BASE + 0xc8) |
| #define KDR_SCD_BAR_DW1 (KDR_SCD_BASE + 0xcc) |
| #define KDR_SCD_QUEUECHAIN_SEL (KDR_SCD_BASE + 0xd0) |
| #define KDR_SCD_QUERY_REQ (KDR_SCD_BASE + 0xd8) |
| #define KDR_SCD_QUERY_RES (KDR_SCD_BASE + 0xdc) |
| #define KDR_SCD_PENDING_FRAMES (KDR_SCD_BASE + 0xe0) |
| #define KDR_SCD_INTERRUPT_MASK (KDR_SCD_BASE + 0xe4) |
| #define KDR_SCD_INTERRUPT_THRESHOLD (KDR_SCD_BASE + 0xe8) |
| #define KDR_SCD_QUERY_MIN_FRAME_SIZE (KDR_SCD_BASE + 0x100) |
| #define KDR_SCD_QUEUE_STATUS_BITS(x) (KDR_SCD_BASE + 0x104 + (x) * 4) |
| |
| /* SP SCD */ |
| #define SHL_SCD_BASE (PRPH_BASE + 0xa02c00) |
| |
| #define SHL_SCD_AIT (SHL_SCD_BASE + 0x0c) |
| #define SHL_SCD_TXFACT (SHL_SCD_BASE + 0x10) |
| #define SHL_SCD_QUEUE_WRPTR(x) (SHL_SCD_BASE + 0x18 + (x) * 4) |
| #define SHL_SCD_QUEUE_RDPTR(x) (SHL_SCD_BASE + 0x68 + (x) * 4) |
| #define SHL_SCD_QUEUECHAIN_SEL (SHL_SCD_BASE + 0xe8) |
| #define SHL_SCD_AGGR_SEL (SHL_SCD_BASE + 0x248) |
| #define SHL_SCD_INTERRUPT_MASK (SHL_SCD_BASE + 0x108) |
| |
| #endif /* __iwl_prph_h__ */ |