| /* |
| * Intel i82586 Ethernet definitions |
| * |
| * This is an extension to the Linux operating system, and is covered by the |
| * same GNU General Public License that covers that work. |
| * |
| * copyrights (c) 1994 by Michael Hipp (hippm@informatik.uni-tuebingen.de) |
| * |
| * I have done a look in the following sources: |
| * crynwr-packet-driver by Russ Nelson |
| * Garret A. Wollman's i82586-driver for BSD |
| */ |
| |
| |
| #define NI52_RESET 0 /* writing to this address, resets the i82586 */ |
| #define NI52_ATTENTION 1 /* channel attention, kick the 586 */ |
| #define NI52_TENA 3 /* 2-5 possibly wrong, Xmit enable */ |
| #define NI52_TDIS 2 /* Xmit disable */ |
| #define NI52_INTENA 5 /* Interrupt enable */ |
| #define NI52_INTDIS 4 /* Interrupt disable */ |
| #define NI52_MAGIC1 6 /* dunno exact function */ |
| #define NI52_MAGIC2 7 /* dunno exact function */ |
| |
| #define NI52_MAGICVAL1 0x00 /* magic-values for ni5210 card */ |
| #define NI52_MAGICVAL2 0x55 |
| |
| /* |
| * where to find the System Configuration Pointer (SCP) |
| */ |
| #define SCP_DEFAULT_ADDRESS 0xfffff4 |
| |
| |
| /* |
| * System Configuration Pointer Struct |
| */ |
| |
| struct scp_struct |
| { |
| u16 zero_dum0; /* has to be zero */ |
| u8 sysbus; /* 0=16Bit,1=8Bit */ |
| u8 zero_dum1; /* has to be zero for 586 */ |
| u16 zero_dum2; |
| u16 zero_dum3; |
| u32 iscp; /* pointer to the iscp-block */ |
| }; |
| |
| |
| /* |
| * Intermediate System Configuration Pointer (ISCP) |
| */ |
| struct iscp_struct |
| { |
| u8 busy; /* 586 clears after successful init */ |
| u8 zero_dummy; /* has to be zero */ |
| u16 scb_offset; /* pointeroffset to the scb_base */ |
| u32 scb_base; /* base-address of all 16-bit offsets */ |
| }; |
| |
| /* |
| * System Control Block (SCB) |
| */ |
| struct scb_struct |
| { |
| u8 rus; |
| u8 cus; |
| u8 cmd_ruc; /* command word: RU part */ |
| u8 cmd_cuc; /* command word: CU part & ACK */ |
| u16 cbl_offset; /* pointeroffset, command block list */ |
| u16 rfa_offset; /* pointeroffset, receive frame area */ |
| u16 crc_errs; /* CRC-Error counter */ |
| u16 aln_errs; /* alignmenterror counter */ |
| u16 rsc_errs; /* Resourceerror counter */ |
| u16 ovrn_errs; /* OVerrunerror counter */ |
| }; |
| |
| /* |
| * possible command values for the command word |
| */ |
| #define RUC_MASK 0x0070 /* mask for RU commands */ |
| #define RUC_NOP 0x0000 /* NOP-command */ |
| #define RUC_START 0x0010 /* start RU */ |
| #define RUC_RESUME 0x0020 /* resume RU after suspend */ |
| #define RUC_SUSPEND 0x0030 /* suspend RU */ |
| #define RUC_ABORT 0x0040 /* abort receiver operation immediately */ |
| |
| #define CUC_MASK 0x07 /* mask for CU command */ |
| #define CUC_NOP 0x00 /* NOP-command */ |
| #define CUC_START 0x01 /* start execution of 1. cmd on the CBL */ |
| #define CUC_RESUME 0x02 /* resume after suspend */ |
| #define CUC_SUSPEND 0x03 /* Suspend CU */ |
| #define CUC_ABORT 0x04 /* abort command operation immediately */ |
| |
| #define ACK_MASK 0xf0 /* mask for ACK command */ |
| #define ACK_CX 0x80 /* acknowledges STAT_CX */ |
| #define ACK_FR 0x40 /* ack. STAT_FR */ |
| #define ACK_CNA 0x20 /* ack. STAT_CNA */ |
| #define ACK_RNR 0x10 /* ack. STAT_RNR */ |
| |
| /* |
| * possible status values for the status word |
| */ |
| #define STAT_MASK 0xf0 /* mask for cause of interrupt */ |
| #define STAT_CX 0x80 /* CU finished cmd with its I bit set */ |
| #define STAT_FR 0x40 /* RU finished receiving a frame */ |
| #define STAT_CNA 0x20 /* CU left active state */ |
| #define STAT_RNR 0x10 /* RU left ready state */ |
| |
| #define CU_STATUS 0x7 /* CU status, 0=idle */ |
| #define CU_SUSPEND 0x1 /* CU is suspended */ |
| #define CU_ACTIVE 0x2 /* CU is active */ |
| |
| #define RU_STATUS 0x70 /* RU status, 0=idle */ |
| #define RU_SUSPEND 0x10 /* RU suspended */ |
| #define RU_NOSPACE 0x20 /* RU no resources */ |
| #define RU_READY 0x40 /* RU is ready */ |
| |
| /* |
| * Receive Frame Descriptor (RFD) |
| */ |
| struct rfd_struct |
| { |
| u8 stat_low; /* status word */ |
| u8 stat_high; /* status word */ |
| u8 rfd_sf; /* 82596 mode only */ |
| u8 last; /* Bit15,Last Frame on List / Bit14,suspend */ |
| u16 next; /* linkoffset to next RFD */ |
| u16 rbd_offset; /* pointeroffset to RBD-buffer */ |
| u8 dest[6]; /* ethernet-address, destination */ |
| u8 source[6]; /* ethernet-address, source */ |
| u16 length; /* 802.3 frame-length */ |
| u16 zero_dummy; /* dummy */ |
| }; |
| |
| #define RFD_LAST 0x80 /* last: last rfd in the list */ |
| #define RFD_SUSP 0x40 /* last: suspend RU after */ |
| #define RFD_COMPL 0x80 |
| #define RFD_OK 0x20 |
| #define RFD_BUSY 0x40 |
| #define RFD_ERR_LEN 0x10 /* Length error (if enabled length-checking */ |
| #define RFD_ERR_CRC 0x08 /* CRC error */ |
| #define RFD_ERR_ALGN 0x04 /* Alignment error */ |
| #define RFD_ERR_RNR 0x02 /* status: receiver out of resources */ |
| #define RFD_ERR_OVR 0x01 /* DMA Overrun! */ |
| |
| #define RFD_ERR_FTS 0x0080 /* Frame to short */ |
| #define RFD_ERR_NEOP 0x0040 /* No EOP flag (for bitstuffing only) */ |
| #define RFD_ERR_TRUN 0x0020 /* (82596 only/SF mode) indicates truncated frame */ |
| #define RFD_MATCHADD 0x0002 /* status: Destinationaddress !matches IA (only 82596) */ |
| #define RFD_COLLDET 0x0001 /* Detected collision during reception */ |
| |
| /* |
| * Receive Buffer Descriptor (RBD) |
| */ |
| struct rbd_struct |
| { |
| u16 status; /* status word,number of used bytes in buff */ |
| u16 next; /* pointeroffset to next RBD */ |
| u32 buffer; /* receive buffer address pointer */ |
| u16 size; /* size of this buffer */ |
| u16 zero_dummy; /* dummy */ |
| }; |
| |
| #define RBD_LAST 0x8000 /* last buffer */ |
| #define RBD_USED 0x4000 /* this buffer has data */ |
| #define RBD_MASK 0x3fff /* size-mask for length */ |
| |
| /* |
| * Statusvalues for Commands/RFD |
| */ |
| #define STAT_COMPL 0x8000 /* status: frame/command is complete */ |
| #define STAT_BUSY 0x4000 /* status: frame/command is busy */ |
| #define STAT_OK 0x2000 /* status: frame/command is ok */ |
| |
| /* |
| * Action-Commands |
| */ |
| #define CMD_NOP 0x0000 /* NOP */ |
| #define CMD_IASETUP 0x0001 /* initial address setup command */ |
| #define CMD_CONFIGURE 0x0002 /* configure command */ |
| #define CMD_MCSETUP 0x0003 /* MC setup command */ |
| #define CMD_XMIT 0x0004 /* transmit command */ |
| #define CMD_TDR 0x0005 /* time domain reflectometer (TDR) command */ |
| #define CMD_DUMP 0x0006 /* dump command */ |
| #define CMD_DIAGNOSE 0x0007 /* diagnose command */ |
| |
| /* |
| * Action command bits |
| */ |
| #define CMD_LAST 0x8000 /* indicates last command in the CBL */ |
| #define CMD_SUSPEND 0x4000 /* suspend CU after this CB */ |
| #define CMD_INT 0x2000 /* generate interrupt after execution */ |
| |
| /* |
| * NOP - command |
| */ |
| struct nop_cmd_struct |
| { |
| u16 cmd_status; /* status of this command */ |
| u16 cmd_cmd; /* the command itself (+bits) */ |
| u16 cmd_link; /* offsetpointer to next command */ |
| }; |
| |
| /* |
| * IA Setup command |
| */ |
| struct iasetup_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u8 iaddr[6]; |
| }; |
| |
| /* |
| * Configure command |
| */ |
| struct configure_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u8 byte_cnt; /* size of the config-cmd */ |
| u8 fifo; /* fifo/recv monitor */ |
| u8 sav_bf; /* save bad frames (bit7=1)*/ |
| u8 adr_len; /* adr_len(0-2),al_loc(3),pream(4-5),loopbak(6-7)*/ |
| u8 priority; /* lin_prio(0-2),exp_prio(4-6),bof_metd(7) */ |
| u8 ifs; /* inter frame spacing */ |
| u8 time_low; /* slot time low */ |
| u8 time_high; /* slot time high(0-2) and max. retries(4-7) */ |
| u8 promisc; /* promisc-mode(0) , et al (1-7) */ |
| u8 carr_coll; /* carrier(0-3)/collision(4-7) stuff */ |
| u8 fram_len; /* minimal frame len */ |
| u8 dummy; /* dummy */ |
| }; |
| |
| /* |
| * Multicast Setup command |
| */ |
| struct mcsetup_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u16 mc_cnt; /* number of bytes in the MC-List */ |
| u8 mc_list[0][6]; /* pointer to 6 bytes entries */ |
| }; |
| |
| /* |
| * DUMP command |
| */ |
| struct dump_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u16 dump_offset; /* pointeroffset to DUMP space */ |
| }; |
| |
| /* |
| * transmit command |
| */ |
| struct transmit_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u16 tbd_offset; /* pointeroffset to TBD */ |
| u8 dest[6]; /* destination address of the frame */ |
| u16 length; /* user defined: 802.3 length / Ether type */ |
| }; |
| |
| #define TCMD_ERRMASK 0x0fa0 |
| #define TCMD_MAXCOLLMASK 0x000f |
| #define TCMD_MAXCOLL 0x0020 |
| #define TCMD_HEARTBEAT 0x0040 |
| #define TCMD_DEFERRED 0x0080 |
| #define TCMD_UNDERRUN 0x0100 |
| #define TCMD_LOSTCTS 0x0200 |
| #define TCMD_NOCARRIER 0x0400 |
| #define TCMD_LATECOLL 0x0800 |
| |
| struct tdr_cmd_struct |
| { |
| u16 cmd_status; |
| u16 cmd_cmd; |
| u16 cmd_link; |
| u16 status; |
| }; |
| |
| #define TDR_LNK_OK 0x8000 /* No link problem identified */ |
| #define TDR_XCVR_PRB 0x4000 /* indicates a transceiver problem */ |
| #define TDR_ET_OPN 0x2000 /* open, no correct termination */ |
| #define TDR_ET_SRT 0x1000 /* TDR detected a short circuit */ |
| #define TDR_TIMEMASK 0x07ff /* mask for the time field */ |
| |
| /* |
| * Transmit Buffer Descriptor (TBD) |
| */ |
| struct tbd_struct |
| { |
| u16 size; /* size + EOF-Flag(15) */ |
| u16 next; /* pointeroffset to next TBD */ |
| u32 buffer; /* pointer to buffer */ |
| }; |
| |
| #define TBD_LAST 0x8000 /* EOF-Flag, indicates last buffer in list */ |
| |
| |
| |
| |