blob: 66814ee64d05e985449d0bb17cb69c580a2f7d8e [file] [log] [blame]
/*
* pata_efar.c - EFAR PIIX clone controller driver
*
* (C) 2005 Red Hat <alan@redhat.com>
*
* Some parts based on ata_piix.c by Jeff Garzik and others.
*
* The EFAR is a PIIX4 clone with UDMA66 support. Unlike the later
* Intel ICH controllers the EFAR widened the UDMA mode register bits
* and doesn't require the funky clock selection.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/ata.h>
#define DRV_NAME "pata_efar"
#define DRV_VERSION "0.4.3"
/**
* efar_pre_reset - check for 40/80 pin
* @ap: Port
*
* Perform cable detection for the EFAR ATA interface. This is
* different to the PIIX arrangement
*/
static int efar_pre_reset(struct ata_port *ap)
{
static const struct pci_bits efar_enable_bits[] = {
{ 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
{ 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u8 tmp;
if (!pci_test_config_bits(pdev, &efar_enable_bits[ap->port_no]))
return -ENOENT;
pci_read_config_byte(pdev, 0x47, &tmp);
if (tmp & (2 >> ap->port_no))
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
return ata_std_prereset(ap);
}
/**
* efar_probe_reset - Probe specified port on PATA host controller
* @ap: Port to probe
*
* LOCKING:
* None (inherited from caller).
*/
static void efar_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, efar_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
}
/**
* efar_set_piomode - Initialize host controller PATA PIO timings
* @ap: Port whose timings we are configuring
* @adev: um
*
* Set PIO mode for device, in host controller PCI config space.
*
* LOCKING:
* None (inherited from caller).
*/
static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
{
unsigned int pio = adev->pio_mode - XFER_PIO_0;
struct pci_dev *dev = to_pci_dev(ap->host->dev);
unsigned int idetm_port= ap->port_no ? 0x42 : 0x40;
u16 idetm_data;
int control = 0;
/*
* See Intel Document 298600-004 for the timing programing rules
* for PIIX/ICH. The EFAR is a clone so very similar
*/
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
if (pio > 2)
control |= 1; /* TIME1 enable */
if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
control |= 2; /* IE enable */
/* Intel specifies that the PPE functionality is for disk only */
if (adev->class == ATA_DEV_ATA)
control |= 4; /* PPE enable */
pci_read_config_word(dev, idetm_port, &idetm_data);
/* Enable PPE, IE and TIME as appropriate */
if (adev->devno == 0) {
idetm_data &= 0xCCF0;
idetm_data |= control;
idetm_data |= (timings[pio][0] << 12) |
(timings[pio][1] << 8);
} else {
int shift = 4 * ap->port_no;
u8 slave_data;
idetm_data &= 0xCC0F;
idetm_data |= (control << 4);
/* Slave timing in seperate register */
pci_read_config_byte(dev, 0x44, &slave_data);
slave_data &= 0x0F << shift;
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
pci_write_config_byte(dev, 0x44, slave_data);
}
idetm_data |= 0x4000; /* Ensure SITRE is enabled */
pci_write_config_word(dev, idetm_port, idetm_data);
}
/**
* efar_set_dmamode - Initialize host controller PATA DMA timings
* @ap: Port whose timings we are configuring
* @adev: Device to program
*
* Set UDMA/MWDMA mode for device, in host controller PCI config space.
*
* LOCKING:
* None (inherited from caller).
*/
static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
{
struct pci_dev *dev = to_pci_dev(ap->host->dev);
u8 master_port = ap->port_no ? 0x42 : 0x40;
u16 master_data;
u8 speed = adev->dma_mode;
int devid = adev->devno + 2 * ap->port_no;
u8 udma_enable;
static const /* ISP RTC */
u8 timings[][2] = { { 0, 0 },
{ 0, 0 },
{ 1, 0 },
{ 2, 1 },
{ 2, 3 }, };
pci_read_config_word(dev, master_port, &master_data);
pci_read_config_byte(dev, 0x48, &udma_enable);
if (speed >= XFER_UDMA_0) {
unsigned int udma = adev->dma_mode - XFER_UDMA_0;
u16 udma_timing;
udma_enable |= (1 << devid);
/* Load the UDMA mode number */
pci_read_config_word(dev, 0x4A, &udma_timing);
udma_timing &= ~(7 << (4 * devid));
udma_timing |= udma << (4 * devid);
pci_write_config_word(dev, 0x4A, udma_timing);
} else {
/*
* MWDMA is driven by the PIO timings. We must also enable
* IORDY unconditionally along with TIME1. PPE has already
* been set when the PIO timing was set.
*/
unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
unsigned int control;
u8 slave_data;
const unsigned int needed_pio[3] = {
XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
};
int pio = needed_pio[mwdma] - XFER_PIO_0;
control = 3; /* IORDY|TIME1 */
/* If the drive MWDMA is faster than it can do PIO then
we must force PIO into PIO0 */
if (adev->pio_mode < needed_pio[mwdma])
/* Enable DMA timing only */
control |= 8; /* PIO cycles in PIO0 */
if (adev->devno) { /* Slave */
master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
master_data |= control << 4;
pci_read_config_byte(dev, 0x44, &slave_data);
slave_data &= (0x0F + 0xE1 * ap->port_no);
/* Load the matching timing */
slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
pci_write_config_byte(dev, 0x44, slave_data);
} else { /* Master */
master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
and master timing bits */
master_data |= control;
master_data |=
(timings[pio][0] << 12) |
(timings[pio][1] << 8);
}
udma_enable &= ~(1 << devid);
pci_write_config_word(dev, master_port, master_data);
}
pci_write_config_byte(dev, 0x48, udma_enable);
}
static struct scsi_host_template efar_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
.resume = ata_scsi_device_resume,
.suspend = ata_scsi_device_suspend,
};
static const struct ata_port_operations efar_ops = {
.port_disable = ata_port_disable,
.set_piomode = efar_set_piomode,
.set_dmamode = efar_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = efar_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_pio_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.port_start = ata_port_start,
};
/**
* efar_init_one - Register EFAR ATA PCI device with kernel services
* @pdev: PCI device to register
* @ent: Entry in efar_pci_tbl matching with @pdev
*
* Called from kernel PCI layer.
*
* LOCKING:
* Inherited from PCI layer (may sleep).
*
* RETURNS:
* Zero on success, or -ERRNO value.
*/
static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
static int printed_version;
static struct ata_port_info info = {
.sht = &efar_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma1-2 */
.udma_mask = 0x0f, /* UDMA 66 */
.port_ops = &efar_ops,
};
static struct ata_port_info *port_info[2] = { &info, &info };
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev,
"version " DRV_VERSION "\n");
return ata_pci_init_one(pdev, port_info, 2);
}
static const struct pci_device_id efar_pci_tbl[] = {
{ PCI_VDEVICE(EFAR, 0x9130), },
{ } /* terminate list */
};
static struct pci_driver efar_pci_driver = {
.name = DRV_NAME,
.id_table = efar_pci_tbl,
.probe = efar_init_one,
.remove = ata_pci_remove_one,
.suspend = ata_pci_device_suspend,
.resume = ata_pci_device_resume,
};
static int __init efar_init(void)
{
return pci_register_driver(&efar_pci_driver);
}
static void __exit efar_exit(void)
{
pci_unregister_driver(&efar_pci_driver);
}
module_init(efar_init);
module_exit(efar_exit);
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("SCSI low-level driver for EFAR PIIX clones");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, efar_pci_tbl);
MODULE_VERSION(DRV_VERSION);