arch/arm/boot/dts/ste-snowball.dts - kernel/msm-4.9 - Gitiles

 /*
  * Copyright 2011 ST-Ericsson AB
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License
  * Version 2 or later at the following locations:
  *
  * http://www.opensource.org/licenses/gpl-license.html
  * http://www.gnu.org/copyleft/gpl.html
  */

 /dts-v1/;
 #include "ste-dbx5x0.dtsi"
 #include "ste-href-ab8500.dtsi"
 #include "ste-href-family-pinctrl.dtsi"

 / {
 	model = "Calao Systems Snowball platform with device tree";
 	compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";

 	/* This stablilizes the serial port enumeration */
 	aliases {
 		serial0 = &ux500_serial0;
 		serial1 = &ux500_serial1;
 		serial2 = &ux500_serial2;
 	};

 	memory {
 		reg = <0x00000000 0x20000000>;
 	};

 	en_3v3_reg: en_3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "en-3v3-fixed-supply";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		/* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
 		gpio = <&ab8500_gpio 25 0x4>;
 		startup-delay-us = <5000>;
 		enable-active-high;
 	};

 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
 		#size-cells = <0>;

 		button@1 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <2>;
 			label = "userpb";
 			gpios = <&gpio1 0 0x4>;
 		};
 		button@2 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <3>;
 			label = "extkb1";
 			gpios = <&gpio4 23 0x4>;
 		};
 		button@3 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <4>;
 			label = "extkb2";
 			gpios = <&gpio4 24 0x4>;
 		};
 		button@4 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <5>;
 			label = "extkb3";
 			gpios = <&gpio5 1 0x4>;
 		};
 		button@5 {
 			debounce_interval = <50>;
 			wakeup-source;
 			linux,code = <6>;
 			label = "extkb4";
 			gpios = <&gpio5 2 0x4>;
 		};
 	};

 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpioled_snowball_mode>;
 		used-led {
 			label = "user_led";
 			gpios = <&gpio4 14 0x4>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 	};

 	soc {
 		usb_per5@a03e0000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&musb_default_mode>;
 			pinctrl-1 = <&musb_sleep_mode>;
 		};

 		sound {
 			compatible = "stericsson,snd-soc-mop500";

 			stericsson,cpu-dai = <&msp1 &msp3>;
 			stericsson,audio-codec = <&codec>;
 		};

 		msp0: msp@80123000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&msp0_default_mode>;
 			status = "okay";
 		};

 		msp1: msp@80124000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&msp1_default_mode>;
 			status = "okay";
 		};

 		msp2: msp@80117000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&msp2_default_mode>;
 		};

 		msp3: msp@80125000 {
 			status = "okay";
 		};

 		external-bus@50000000 {
 			status = "okay";

 			ethernet@0 {
 				compatible = "smsc,lan9115";
 				reg = <0 0x10000>;
 				interrupts = <12 IRQ_TYPE_EDGE_RISING>;
 				interrupt-parent = <&gpio4>;
 				vdd33a-supply = <&en_3v3_reg>;
 				vddvario-supply = <&db8500_vape_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&eth_snowball_mode>;

 				reg-shift = <1>;
 				reg-io-width = <2>;
 				smsc,force-internal-phy;
 				smsc,irq-active-high;
 				smsc,irq-push-pull;

 				clocks = <&prcc_pclk 3 0>;
 			};
 		};

 		vmmci: regulator-gpio {
 			compatible = "regulator-gpio";

 			gpios = <&gpio7 4 0x4>;
 			enable-gpio = <&gpio6 25 0x4>;

 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <2900000>;
 			regulator-name = "mmci-reg";
 			regulator-type = "voltage";

 			startup-delay-us = <100>;
 			enable-active-high;

 			states = <1800000 0x1
 				  2900000 0x0>;
 		};

 		// External Micro SD slot
 		sdi0_per1@80126000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
 			vqmmc-supply = <&vmmci>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdi0_default_mode>;
 			pinctrl-1 = <&sdi0_sleep_mode>;

 			cd-gpios  = <&gpio6 26 0x4>; // 218
 			cd-inverted;

 			status = "okay";
 		};

 		// WLAN SDIO channel
 		sdi1_per2@80118000 {
 			arm,primecell-periphid = <0x10480180>;
 			max-frequency = <100000000>;
 			bus-width = <4>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdi1_default_mode>;
 			pinctrl-1 = <&sdi1_sleep_mode>;

 			status = "okay";
 		};

 		// Unused PoP eMMC - register and put it to sleep by default */
 		sdi2_per3@80005000 {
 			arm,primecell-periphid = <0x10480180>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&sdi2_sleep_mode>;

 			status = "okay";
 		};

 		// On-board eMMC
 		sdi4_per2@80114000 {
 			arm,primecell-periphid = <0x10480180>;
 		        max-frequency = <100000000>;
 			bus-width = <8>;
 			cap-mmc-highspeed;
 			vmmc-supply = <&ab8500_ldo_aux2_reg>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdi4_default_mode>;
 			pinctrl-1 = <&sdi4_sleep_mode>;

 			status = "okay";
 		};

 		uart@80120000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart0_default_mode>;
 			pinctrl-1 = <&uart0_sleep_mode>;
 			status = "okay";
 		};

 		/* This UART is unused and thus left disabled */
 		uart@80121000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart1_default_mode>;
 			pinctrl-1 = <&uart1_sleep_mode>;
 		};

 		uart@80007000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart2_default_mode>;
 			pinctrl-1 = <&uart2_sleep_mode>;
 			status = "okay";
 		};

 		i2c@80004000 {
 			pinctrl-names = "default","sleep";
 			pinctrl-0 = <&i2c0_default_mode>;
 			pinctrl-1 = <&i2c0_sleep_mode>;
 		};

 		i2c@80122000 {
 			pinctrl-names = "default","sleep";
 			pinctrl-0 = <&i2c1_default_mode>;
 			pinctrl-1 = <&i2c1_sleep_mode>;
 		};

 		i2c@80128000 {
 			pinctrl-names = "default","sleep";
 			pinctrl-0 = <&i2c2_default_mode>;
 			pinctrl-1 = <&i2c2_sleep_mode>;
 			lsm303dlh@18 {
 				/* Accelerometer */
 				compatible = "st,lsm303dlh-accel";
 				st,drdy-int-pin = <1>;
 				reg = <0x18>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_snowball_mode>;
 				interrupt-parent = <&gpio5>;
 				interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
 					     <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
 			};
 			lsm303dlh@1e {
 				/* Magnetometer */
 				compatible = "st,lsm303dlh-magn";
 				reg = <0x1e>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&magneto_snowball_mode>;
 				gpios = <&gpio5 5 0x4>; /* DRDY line */
 			};
 			l3g4200d@68 {
 				/* Gyroscope */
 				compatible = "st,l3g4200d-gyro";
 				st,drdy-int-pin = <2>;
 				reg = <0x68>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&gyro_snowball_mode>;
 				gpios = <&gpio5 6 0x4>; /* DRDY line */
 				interrupt-parent = <&gpio5>;
 				interrupts = <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
 			};
 			lsp001wm@5c {
 				/* Barometer/pressure sensor */
 				compatible = "st,lps001wp-press";
 				reg = <0x5c>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>;
 				vddio-supply = <&db8500_vsmps2_reg>;
 			};
 		};

 		i2c@80110000 {
 			pinctrl-names = "default","sleep";
 			pinctrl-0 = <&i2c3_default_mode>;
 			pinctrl-1 = <&i2c3_sleep_mode>;
 		};

 		ssp@80002000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&ssp0_snowball_mode>;
 		};

 		cpufreq-cooling {
 			status = "okay";
 		};

 		prcmu@80157000 {
 			cpufreq {
 				status = "okay";
 			};

 			thermal@801573c0 {
 				num-trips = <4>;

 				trip0-temp = <70000>;
 				trip0-type = "active";
 				trip0-cdev-num = <1>;
 				trip0-cdev-name0 = "thermal-cpufreq-0";

 				trip1-temp = <75000>;
 				trip1-type = "active";
 				trip1-cdev-num = <1>;
 				trip1-cdev-name0 = "thermal-cpufreq-0";

 				trip2-temp = <80000>;
 				trip2-type = "active";
 				trip2-cdev-num = <1>;
 				trip2-cdev-name0 = "thermal-cpufreq-0";

 				trip3-temp = <85000>;
 				trip3-type = "critical";
 				trip3-cdev-num = <0>;

 				status = "okay";
 			};

 			ab8500 {
 				ab8500-gpio {
 					compatible = "stericsson,ab8500-gpio";
 				};

 				ext_regulators: ab8500-ext-regulators {
 					ab8500_ext1_reg: ab8500_ext1 {
 						regulator-name = "ab8500-ext-supply1";
 					};

 					ab8500_ext2_reg_reg: ab8500_ext2 {
 						regulator-name = "ab8500-ext-supply2";
 					};

 					ab8500_ext3_reg_reg: ab8500_ext3 {
 						regulator-name = "ab8500-ext-supply3";
 					};
 				};

 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
 					};

 					ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
 						regulator-name = "V-eMMC1";
 					};

 					ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
 						regulator-name = "V-MMC-SD";
 					};

 					ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
 						regulator-name = "V-INTCORE";
 					};

 					ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
 						regulator-name = "V-TVOUT";
 					};

 					ab8500_ldo_usb_reg: ab8500_ldo_usb {
 						regulator-name = "dummy";
 					};

 					ab8500_ldo_audio_reg: ab8500_ldo_audio {
 						regulator-name = "V-AUD";
 					};

 					ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
 						regulator-name = "V-AMIC1";
 					};

 					ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
 						regulator-name = "V-AMIC2";
 					};

 					ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
 						regulator-name = "V-DMIC";
 					};

 					ab8500_ldo_ana_reg: ab8500_ldo_ana {
 						regulator-name = "V-CSI/DSI";
 					};
 				};
 			};
 		};

 		pinctrl {
 			/*
 			 * Set this up using hogs, as time goes by and as seems fit, these
 			 * can be moved over to being controlled by respective device.
 			 */
 			pinctrl-names = "default";
 			pinctrl-0 = <&gbf_snowball_mode>,
 				  <&wlan_snowball_mode>;

 			ethernet {
 				/*
 				 * Mux in "SM" which is used for the
 				 * SMSC911x Ethernet adapter
 				 */
 				eth_snowball_mode: eth_snowball {
 					snowball_mux {
 						function = "sm";
 						groups = "sm_b_1";
 					};
 					/* LAN IRQ pin */
 					snowball_cfg1 {
 						pins = "GPIO140_B11";
 						ste,config = <&in_nopull>;
 					};
 					/* LAN reset pin */
 					snowball_cfg2 {
 						pins = "GPIO141_C12";
 						ste,config = <&gpio_out_hi>;
 					};

 				};
 			};
 			sdi0 {
 				sdi0_default_mode: sdi0_default {
 					snowball_mux {
 						function = "mc0";
 						groups = "mc0dat31dir_a_1";
 					};
 					snowball_cfg1 {
 						pins = "GPIO21_AB3"; /* DAT31DIR */
 						ste,config = <&out_hi>;
 					};
 					/* SD card detect GPIO pin, extend default state */
 					snowball_cfg2 {
 						pins = "GPIO218_AH11";
 						ste,config = <&gpio_in_pu>;
 					};
 					/* VMMCI level-shifter enable */
 					snowball_cfg3 {
 						pins = "GPIO217_AH12";
 						ste,config = <&gpio_out_lo>;
 					};
 					/* VMMCI level-shifter voltage select */
 					snowball_cfg4 {
 						pins = "GPIO228_AJ6";
 						ste,config = <&gpio_out_hi>;
 					};
 				};
 			};
 			ssp0 {
 				ssp0_snowball_mode: ssp0_snowball_default {
 					snowball_mux {
 						function = "ssp0";
 						groups = "ssp0_a_1";
 					};
 					snowball_cfg1 {
 						pins = "GPIO144_B13"; /* FRM */
 						ste,config = <&gpio_out_hi>;
 					};
 					snowball_cfg2 {
 						pins = "GPIO145_C13"; /* RXD */
 						ste,config = <&in_pd>;
 					};
 					snowball_cfg3 {
 						pins =
 						"GPIO146_D13", /* TXD */
 						"GPIO143_D12"; /* CLK */
 						ste,config = <&out_lo>;
 					};

 				};
 			};
 			gpio_led {
 				gpioled_snowball_mode: gpioled_default {
 					snowball_cfg1 {
 						pins = "GPIO142_C11";
 						ste,config = <&gpio_out_hi>;
 					};

 				};
 			};
 			accelerometer {
 				accel_snowball_mode: accel_snowball {
 					/* Accelerometer lines */
 					snowball_cfg1 {
 						pins =
 						"GPIO163_C20", /* ACCEL_IRQ1 */
 						"GPIO164_B21"; /* ACCEL_IRQ2 */
 						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};
 			gyro {
 				gyro_snowball_mode: gyro_snowball {
 					snowball_cfg1 {
 						pins =
 						"GPIO166_A22", /* DRDY */
 						"GPIO169_D22"; /* INT */
 						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};
 			magnetometer {
 				magneto_snowball_mode: magneto_snowball {
 					snowball_cfg1 {
 						pins = "GPIO165_C21"; /* MAG_DRDY */
 						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};
 			gbf {
 				gbf_snowball_mode: gbf_snowball {
 					/*
 					 * GBF (GPS, Bluetooth, FM-radio) interface,
 					 * pull low to reset state
 					 */
 					snowball_cfg1 {
 						pins = "GPIO171_D23"; /* GBF_ENA_RESET */
 						ste,config = <&gpio_out_lo>;
 					};
 				 };
 			};
 			wlan {
 				wlan_snowball_mode: wlan_snowball {
 					/*
 					 * Activate this mode with the WLAN chip.
 					 * These are plain GPIO pins used by WLAN
 					 */
 					snowball_cfg1 {
 						pins =
 						"GPIO161_D21", /* WLAN_PMU_EN */
 						"GPIO215_AH13"; /* WLAN_ENA */
 						ste,config = <&gpio_out_lo>;
 					};
 					snowball_cfg2 {
 						pins = "GPIO216_AG12"; /* WLAN_IRQ */
 						ste,config = <&gpio_in_pu>;
 					};
 				};
 			};
 		};

 		mcde@a0350000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&lcd_default_mode>;
 			pinctrl-1 = <&lcd_sleep_mode>;
 		};
 	};
 };
	/*
	* Copyright 2011 ST-Ericsson AB
	*
	* The code contained herein is licensed under the GNU General Public
	* License. You may obtain a copy of the GNU General Public License
	* Version 2 or later at the following locations:
	*
	* http://www.opensource.org/licenses/gpl-license.html
	* http://www.gnu.org/copyleft/gpl.html
	*/

	/dts-v1/;
	#include "ste-dbx5x0.dtsi"
	#include "ste-href-ab8500.dtsi"
	#include "ste-href-family-pinctrl.dtsi"

	/ {
	model = "Calao Systems Snowball platform with device tree";
	compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500";

	/* This stablilizes the serial port enumeration */
	aliases {
	serial0 = &ux500_serial0;
	serial1 = &ux500_serial1;
	serial2 = &ux500_serial2;
	};

	memory {
	reg = <0x00000000 0x20000000>;
	};

	en_3v3_reg: en_3v3 {
	compatible = "regulator-fixed";
	regulator-name = "en-3v3-fixed-supply";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	/* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */
	gpio = <&ab8500_gpio 25 0x4>;
	startup-delay-us = <5000>;
	enable-active-high;
	};

	gpio_keys {
	compatible = "gpio-keys";
	#address-cells = <1>;
	#size-cells = <0>;

	button@1 {
	debounce_interval = <50>;
	wakeup-source;
	linux,code = <2>;
	label = "userpb";
	gpios = <&gpio1 0 0x4>;
	};
	button@2 {
	debounce_interval = <50>;
	wakeup-source;
	linux,code = <3>;
	label = "extkb1";
	gpios = <&gpio4 23 0x4>;
	};
	button@3 {
	debounce_interval = <50>;
	wakeup-source;
	linux,code = <4>;
	label = "extkb2";
	gpios = <&gpio4 24 0x4>;
	};
	button@4 {
	debounce_interval = <50>;
	wakeup-source;
	linux,code = <5>;
	label = "extkb3";
	gpios = <&gpio5 1 0x4>;
	};
	button@5 {
	debounce_interval = <50>;
	wakeup-source;
	linux,code = <6>;
	label = "extkb4";
	gpios = <&gpio5 2 0x4>;
	};
	};

	leds {
	compatible = "gpio-leds";
	pinctrl-names = "default";
	pinctrl-0 = <&gpioled_snowball_mode>;
	used-led {
	label = "user_led";
	gpios = <&gpio4 14 0x4>;
	default-state = "on";
	linux,default-trigger = "heartbeat";
	};
	};

	soc {
	usb_per5@a03e0000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&musb_default_mode>;
	pinctrl-1 = <&musb_sleep_mode>;
	};

	sound {
	compatible = "stericsson,snd-soc-mop500";

	stericsson,cpu-dai = <&msp1 &msp3>;
	stericsson,audio-codec = <&codec>;
	};

	msp0: msp@80123000 {
	pinctrl-names = "default";
	pinctrl-0 = <&msp0_default_mode>;
	status = "okay";
	};

	msp1: msp@80124000 {
	pinctrl-names = "default";
	pinctrl-0 = <&msp1_default_mode>;
	status = "okay";
	};

	msp2: msp@80117000 {
	pinctrl-names = "default";
	pinctrl-0 = <&msp2_default_mode>;
	};

	msp3: msp@80125000 {
	status = "okay";
	};

	external-bus@50000000 {
	status = "okay";

	ethernet@0 {
	compatible = "smsc,lan9115";
	reg = <0 0x10000>;
	interrupts = <12 IRQ_TYPE_EDGE_RISING>;
	interrupt-parent = <&gpio4>;
	vdd33a-supply = <&en_3v3_reg>;
	vddvario-supply = <&db8500_vape_reg>;
	pinctrl-names = "default";
	pinctrl-0 = <&eth_snowball_mode>;

	reg-shift = <1>;
	reg-io-width = <2>;
	smsc,force-internal-phy;
	smsc,irq-active-high;
	smsc,irq-push-pull;

	clocks = <&prcc_pclk 3 0>;
	};
	};

	vmmci: regulator-gpio {
	compatible = "regulator-gpio";

	gpios = <&gpio7 4 0x4>;
	enable-gpio = <&gpio6 25 0x4>;

	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <2900000>;
	regulator-name = "mmci-reg";
	regulator-type = "voltage";

	startup-delay-us = <100>;
	enable-active-high;

	states = <1800000 0x1
	2900000 0x0>;
	};

	// External Micro SD slot
	sdi0_per1@80126000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <100000000>;
	bus-width = <4>;
	cap-mmc-highspeed;
	vmmc-supply = <&ab8500_ldo_aux3_reg>;
	vqmmc-supply = <&vmmci>;
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&sdi0_default_mode>;
	pinctrl-1 = <&sdi0_sleep_mode>;

	cd-gpios = <&gpio6 26 0x4>; // 218
	cd-inverted;

	status = "okay";
	};

	// WLAN SDIO channel
	sdi1_per2@80118000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <100000000>;
	bus-width = <4>;
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&sdi1_default_mode>;
	pinctrl-1 = <&sdi1_sleep_mode>;

	status = "okay";
	};

	// Unused PoP eMMC - register and put it to sleep by default */
	sdi2_per3@80005000 {
	arm,primecell-periphid = <0x10480180>;
	pinctrl-names = "default";
	pinctrl-0 = <&sdi2_sleep_mode>;

	status = "okay";
	};

	// On-board eMMC
	sdi4_per2@80114000 {
	arm,primecell-periphid = <0x10480180>;
	max-frequency = <100000000>;
	bus-width = <8>;
	cap-mmc-highspeed;
	vmmc-supply = <&ab8500_ldo_aux2_reg>;
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&sdi4_default_mode>;
	pinctrl-1 = <&sdi4_sleep_mode>;

	status = "okay";
	};

	uart@80120000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart0_default_mode>;
	pinctrl-1 = <&uart0_sleep_mode>;
	status = "okay";
	};

	/* This UART is unused and thus left disabled */
	uart@80121000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart1_default_mode>;
	pinctrl-1 = <&uart1_sleep_mode>;
	};

	uart@80007000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&uart2_default_mode>;
	pinctrl-1 = <&uart2_sleep_mode>;
	status = "okay";
	};

	i2c@80004000 {
	pinctrl-names = "default","sleep";
	pinctrl-0 = <&i2c0_default_mode>;
	pinctrl-1 = <&i2c0_sleep_mode>;
	};

	i2c@80122000 {
	pinctrl-names = "default","sleep";
	pinctrl-0 = <&i2c1_default_mode>;
	pinctrl-1 = <&i2c1_sleep_mode>;
	};

	i2c@80128000 {
	pinctrl-names = "default","sleep";
	pinctrl-0 = <&i2c2_default_mode>;
	pinctrl-1 = <&i2c2_sleep_mode>;
	lsm303dlh@18 {
	/* Accelerometer */
	compatible = "st,lsm303dlh-accel";
	st,drdy-int-pin = <1>;
	reg = <0x18>;
	vdd-supply = <&ab8500_ldo_aux1_reg>;
	vddio-supply = <&db8500_vsmps2_reg>;
	pinctrl-names = "default";
	pinctrl-0 = <&accel_snowball_mode>;
	interrupt-parent = <&gpio5>;
	interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
	<4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
	};
	lsm303dlh@1e {
	/* Magnetometer */
	compatible = "st,lsm303dlh-magn";
	reg = <0x1e>;
	vdd-supply = <&ab8500_ldo_aux1_reg>;
	vddio-supply = <&db8500_vsmps2_reg>;
	pinctrl-names = "default";
	pinctrl-0 = <&magneto_snowball_mode>;
	gpios = <&gpio5 5 0x4>; /* DRDY line */
	};
	l3g4200d@68 {
	/* Gyroscope */
	compatible = "st,l3g4200d-gyro";
	st,drdy-int-pin = <2>;
	reg = <0x68>;
	vdd-supply = <&ab8500_ldo_aux1_reg>;
	vddio-supply = <&db8500_vsmps2_reg>;
	pinctrl-names = "default";
	pinctrl-0 = <&gyro_snowball_mode>;
	gpios = <&gpio5 6 0x4>; /* DRDY line */
	interrupt-parent = <&gpio5>;
	interrupts = <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
	};
	lsp001wm@5c {
	/* Barometer/pressure sensor */
	compatible = "st,lps001wp-press";
	reg = <0x5c>;
	vdd-supply = <&ab8500_ldo_aux1_reg>;
	vddio-supply = <&db8500_vsmps2_reg>;
	};
	};

	i2c@80110000 {
	pinctrl-names = "default","sleep";
	pinctrl-0 = <&i2c3_default_mode>;
	pinctrl-1 = <&i2c3_sleep_mode>;
	};

	ssp@80002000 {
	pinctrl-names = "default";
	pinctrl-0 = <&ssp0_snowball_mode>;
	};

	cpufreq-cooling {
	status = "okay";
	};

	prcmu@80157000 {
	cpufreq {
	status = "okay";
	};

	thermal@801573c0 {
	num-trips = <4>;

	trip0-temp = <70000>;
	trip0-type = "active";
	trip0-cdev-num = <1>;
	trip0-cdev-name0 = "thermal-cpufreq-0";

	trip1-temp = <75000>;
	trip1-type = "active";
	trip1-cdev-num = <1>;
	trip1-cdev-name0 = "thermal-cpufreq-0";

	trip2-temp = <80000>;
	trip2-type = "active";
	trip2-cdev-num = <1>;
	trip2-cdev-name0 = "thermal-cpufreq-0";

	trip3-temp = <85000>;
	trip3-type = "critical";
	trip3-cdev-num = <0>;

	status = "okay";
	};

	ab8500 {
	ab8500-gpio {
	compatible = "stericsson,ab8500-gpio";
	};

	ext_regulators: ab8500-ext-regulators {
	ab8500_ext1_reg: ab8500_ext1 {
	regulator-name = "ab8500-ext-supply1";
	};

	ab8500_ext2_reg_reg: ab8500_ext2 {
	regulator-name = "ab8500-ext-supply2";
	};

	ab8500_ext3_reg_reg: ab8500_ext3 {
	regulator-name = "ab8500-ext-supply3";
	};
	};

	ab8500-regulators {
	ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
	regulator-name = "V-DISPLAY";
	};

	ab8500_ldo_aux2_reg: ab8500_ldo_aux2 {
	regulator-name = "V-eMMC1";
	};

	ab8500_ldo_aux3_reg: ab8500_ldo_aux3 {
	regulator-name = "V-MMC-SD";
	};

	ab8500_ldo_intcore_reg: ab8500_ldo_intcore {
	regulator-name = "V-INTCORE";
	};

	ab8500_ldo_tvout_reg: ab8500_ldo_tvout {
	regulator-name = "V-TVOUT";
	};

	ab8500_ldo_usb_reg: ab8500_ldo_usb {
	regulator-name = "dummy";
	};

	ab8500_ldo_audio_reg: ab8500_ldo_audio {
	regulator-name = "V-AUD";
	};

	ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 {
	regulator-name = "V-AMIC1";
	};

	ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 {
	regulator-name = "V-AMIC2";
	};

	ab8500_ldo_dmic_reg: ab8500_ldo_dmic {
	regulator-name = "V-DMIC";
	};

	ab8500_ldo_ana_reg: ab8500_ldo_ana {
	regulator-name = "V-CSI/DSI";
	};
	};
	};
	};

	pinctrl {
	/*
	* Set this up using hogs, as time goes by and as seems fit, these
	* can be moved over to being controlled by respective device.
	*/
	pinctrl-names = "default";
	pinctrl-0 = <&gbf_snowball_mode>,
	<&wlan_snowball_mode>;

	ethernet {
	/*
	* Mux in "SM" which is used for the
	* SMSC911x Ethernet adapter
	*/
	eth_snowball_mode: eth_snowball {
	snowball_mux {
	function = "sm";
	groups = "sm_b_1";
	};
	/* LAN IRQ pin */
	snowball_cfg1 {
	pins = "GPIO140_B11";
	ste,config = <&in_nopull>;
	};
	/* LAN reset pin */
	snowball_cfg2 {
	pins = "GPIO141_C12";
	ste,config = <&gpio_out_hi>;
	};

	};
	};
	sdi0 {
	sdi0_default_mode: sdi0_default {
	snowball_mux {
	function = "mc0";
	groups = "mc0dat31dir_a_1";
	};
	snowball_cfg1 {
	pins = "GPIO21_AB3"; /* DAT31DIR */
	ste,config = <&out_hi>;
	};
	/* SD card detect GPIO pin, extend default state */
	snowball_cfg2 {
	pins = "GPIO218_AH11";
	ste,config = <&gpio_in_pu>;
	};
	/* VMMCI level-shifter enable */
	snowball_cfg3 {
	pins = "GPIO217_AH12";
	ste,config = <&gpio_out_lo>;
	};
	/* VMMCI level-shifter voltage select */
	snowball_cfg4 {
	pins = "GPIO228_AJ6";
	ste,config = <&gpio_out_hi>;
	};
	};
	};
	ssp0 {
	ssp0_snowball_mode: ssp0_snowball_default {
	snowball_mux {
	function = "ssp0";
	groups = "ssp0_a_1";
	};
	snowball_cfg1 {
	pins = "GPIO144_B13"; /* FRM */
	ste,config = <&gpio_out_hi>;
	};
	snowball_cfg2 {
	pins = "GPIO145_C13"; /* RXD */
	ste,config = <&in_pd>;
	};
	snowball_cfg3 {
	pins =
	"GPIO146_D13", /* TXD */
	"GPIO143_D12"; /* CLK */
	ste,config = <&out_lo>;
	};

	};
	};
	gpio_led {
	gpioled_snowball_mode: gpioled_default {
	snowball_cfg1 {
	pins = "GPIO142_C11";
	ste,config = <&gpio_out_hi>;
	};

	};
	};
	accelerometer {
	accel_snowball_mode: accel_snowball {
	/* Accelerometer lines */
	snowball_cfg1 {
	pins =
	"GPIO163_C20", /* ACCEL_IRQ1 */
	"GPIO164_B21"; /* ACCEL_IRQ2 */
	ste,config = <&gpio_in_pu>;
	};
	};
	};
	gyro {
	gyro_snowball_mode: gyro_snowball {
	snowball_cfg1 {
	pins =
	"GPIO166_A22", /* DRDY */
	"GPIO169_D22"; /* INT */
	ste,config = <&gpio_in_pu>;
	};
	};
	};
	magnetometer {
	magneto_snowball_mode: magneto_snowball {
	snowball_cfg1 {
	pins = "GPIO165_C21"; /* MAG_DRDY */
	ste,config = <&gpio_in_pu>;
	};
	};
	};
	gbf {
	gbf_snowball_mode: gbf_snowball {
	/*
	* GBF (GPS, Bluetooth, FM-radio) interface,
	* pull low to reset state
	*/
	snowball_cfg1 {
	pins = "GPIO171_D23"; /* GBF_ENA_RESET */
	ste,config = <&gpio_out_lo>;
	};
	};
	};
	wlan {
	wlan_snowball_mode: wlan_snowball {
	/*
	* Activate this mode with the WLAN chip.
	* These are plain GPIO pins used by WLAN
	*/
	snowball_cfg1 {
	pins =
	"GPIO161_D21", /* WLAN_PMU_EN */
	"GPIO215_AH13"; /* WLAN_ENA */
	ste,config = <&gpio_out_lo>;
	};
	snowball_cfg2 {
	pins = "GPIO216_AG12"; /* WLAN_IRQ */
	ste,config = <&gpio_in_pu>;
	};
	};
	};
	};

	mcde@a0350000 {
	pinctrl-names = "default", "sleep";
	pinctrl-0 = <&lcd_default_mode>;
	pinctrl-1 = <&lcd_sleep_mode>;
	};
	};
	};