| /* Copyright (c) 2013-2014, 2017, 2020, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/clkdev.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/leds.h> |
| #include <linux/platform_device.h> |
| #include <linux/of_gpio.h> |
| #include <linux/gpio.h> |
| #include <linux/of.h> |
| #include <linux/printk.h> |
| #include <linux/list.h> |
| #include <linux/clk/msm-clk.h> |
| #include <linux/clk/msm-clk-provider.h> |
| #include <linux/pinctrl/consumer.h> |
| |
| /* #define CONFIG_GPIO_FLASH_DEBUG */ |
| #undef CDBG |
| #ifdef CONFIG_GPIO_FLASH_DEBUG |
| #define CDBG(fmt, args...) pr_err(fmt, ##args) |
| #else |
| #define CDBG(fmt, args...) do { } while (0) |
| #endif |
| |
| #define LED_GPIO_FLASH_DRIVER_NAME "qcom,leds-gpio-flash" |
| #define LED_TRIGGER_DEFAULT "none" |
| |
| #define GPIO_OUT_LOW (0 << 1) |
| #define GPIO_OUT_HIGH (1 << 1) |
| |
| #define DUTY_CYCLE_BASE 100 |
| |
| enum msm_flash_seq_type_t { |
| FLASH_EN, |
| FLASH_NOW, |
| }; |
| |
| enum msm_flash_gpio_type_t { |
| NORMAL_GPIO, |
| CLK_GPIO, |
| }; |
| |
| struct msm_flash_ctrl_seq { |
| enum msm_flash_seq_type_t seq_type; |
| uint8_t flash_on_val; |
| uint8_t torch_on_val; |
| }; |
| |
| struct led_gpio_flash_data { |
| int flash_en; |
| int flash_now; |
| struct clk *flash_en_clk; |
| struct clk *flash_now_clk; |
| int brightness; |
| atomic_t clk_enabled[2]; |
| uint32_t clk_freq[2]; |
| uint32_t duty_cycle[2]; |
| enum msm_flash_gpio_type_t gpio_type[2]; |
| struct led_classdev cdev; |
| struct pinctrl *pinctrl; |
| struct pinctrl_state *gpio_state_default; |
| struct msm_flash_ctrl_seq ctrl_seq[2]; |
| }; |
| |
| static const struct of_device_id led_gpio_flash_of_match[] = { |
| {.compatible = LED_GPIO_FLASH_DRIVER_NAME,}, |
| {}, |
| }; |
| |
| static void led_gpio_brightness_set(struct led_classdev *led_cdev, |
| enum led_brightness value) |
| { |
| int rc = 0; |
| int brightness = value; |
| int flash_en = 0; |
| int flash_now = 0; |
| struct led_gpio_flash_data *flash_led = |
| container_of(led_cdev, struct led_gpio_flash_data, cdev); |
| |
| if (brightness > LED_HALF) { |
| flash_en = |
| flash_led->ctrl_seq[FLASH_EN].flash_on_val; |
| flash_now = |
| flash_led->ctrl_seq[FLASH_NOW].flash_on_val; |
| } else if (brightness > LED_OFF) { |
| flash_en = |
| flash_led->ctrl_seq[FLASH_EN].torch_on_val; |
| flash_now = |
| flash_led->ctrl_seq[FLASH_NOW].torch_on_val; |
| } else { |
| flash_en = 0; |
| flash_now = 0; |
| } |
| |
| CDBG("%s:flash_en=%d, flash_now=%d\n", __func__, flash_en, flash_now); |
| |
| if (flash_led->gpio_type[FLASH_EN] == NORMAL_GPIO) { |
| rc = gpio_direction_output(flash_led->flash_en, flash_en); |
| } else { |
| if (flash_en == GPIO_OUT_HIGH && |
| !atomic_read(&flash_led->clk_enabled[FLASH_EN])) { |
| rc = clk_prepare_enable(flash_led->flash_en_clk); |
| atomic_set(&flash_led->clk_enabled[FLASH_EN], 1); |
| } else if (flash_en == GPIO_OUT_LOW && |
| atomic_read(&flash_led->clk_enabled[FLASH_EN])) { |
| clk_disable_unprepare(flash_led->flash_en_clk); |
| atomic_set(&flash_led->clk_enabled[FLASH_EN], 0); |
| } |
| } |
| |
| if (rc) { |
| pr_err("%s: Failed to set flash en.\n", __func__); |
| return; |
| } |
| |
| if (flash_led->gpio_type[FLASH_NOW] == NORMAL_GPIO) { |
| rc = gpio_direction_output(flash_led->flash_now, flash_now); |
| } else { |
| if (flash_now == GPIO_OUT_HIGH && |
| !atomic_read(&flash_led->clk_enabled[FLASH_NOW])) { |
| rc = clk_prepare_enable(flash_led->flash_now_clk); |
| atomic_set(&flash_led->clk_enabled[FLASH_NOW], 1); |
| } else if (flash_now == GPIO_OUT_LOW && |
| atomic_read(&flash_led->clk_enabled[FLASH_NOW])) { |
| clk_disable_unprepare(flash_led->flash_now_clk); |
| atomic_set(&flash_led->clk_enabled[FLASH_NOW], 0); |
| } |
| } |
| |
| if (rc) { |
| pr_err("%s: Failed to set flash now.\n", __func__); |
| return; |
| } |
| |
| flash_led->brightness = brightness; |
| } |
| |
| static enum led_brightness led_gpio_brightness_get(struct led_classdev |
| *led_cdev) |
| { |
| struct led_gpio_flash_data *flash_led = |
| container_of(led_cdev, struct led_gpio_flash_data, cdev); |
| return flash_led->brightness; |
| } |
| |
| static int led_gpio_get_dt_data(struct device *dev, |
| struct led_gpio_flash_data *flash_led) |
| { |
| int rc = 0; |
| int i = 0; |
| const char *temp_str = NULL; |
| const char *seq_name = NULL; |
| uint32_t array_flash_seq[2]; |
| uint32_t array_torch_seq[2]; |
| struct device_node *node = dev->of_node; |
| |
| flash_led->cdev.default_trigger = LED_TRIGGER_DEFAULT; |
| rc = of_property_read_string(node, "linux,default-trigger", |
| &temp_str); |
| if (!rc) |
| flash_led->cdev.default_trigger = temp_str; |
| |
| rc = of_property_read_string(node, "linux,name", &flash_led->cdev.name); |
| if (rc) { |
| pr_err("Failed to read linux name. rc = %d\n", rc); |
| return rc; |
| } |
| |
| /* Configure the gpio type as NORMAL_GPIO by default, |
| * the gpio type should be CLK_GPIO if the frequency |
| * is not 0. |
| */ |
| flash_led->gpio_type[FLASH_EN] = NORMAL_GPIO; |
| flash_led->gpio_type[FLASH_NOW] = NORMAL_GPIO; |
| rc = of_property_read_u32_array(node, "qcom,clk-freq", |
| flash_led->clk_freq, 2); |
| if (!rc) { |
| if (flash_led->clk_freq[FLASH_EN]) |
| flash_led->gpio_type[FLASH_EN] = CLK_GPIO; |
| |
| if (flash_led->clk_freq[FLASH_NOW]) |
| flash_led->gpio_type[FLASH_NOW] = CLK_GPIO; |
| } |
| |
| if (flash_led->gpio_type[FLASH_EN] == NORMAL_GPIO) { |
| flash_led->flash_en = |
| of_get_named_gpio(node, "qcom,flash-en", 0); |
| if (flash_led->flash_en < 0) { |
| pr_err("Read flash-en property failed. rc = %d\n", |
| flash_led->flash_en); |
| return -EINVAL; |
| } |
| rc = gpio_request(flash_led->flash_en, "FLASH_EN"); |
| if (rc) { |
| pr_err("%s: Failed to request gpio %d,rc = %d\n", |
| __func__, flash_led->flash_en, rc); |
| return rc; |
| } |
| } else { |
| flash_led->flash_en_clk = |
| devm_clk_get(dev, "flash_en_clk"); |
| if (IS_ERR(flash_led->flash_en_clk)) { |
| pr_err("Failed to get flash-en clk.\n"); |
| return -EINVAL; |
| } |
| |
| flash_led->clk_freq[FLASH_EN] = |
| clk_round_rate(flash_led->flash_en_clk, |
| flash_led->clk_freq[FLASH_EN]); |
| rc = clk_set_rate(flash_led->flash_en_clk, |
| flash_led->clk_freq[FLASH_EN]); |
| if (rc) { |
| pr_err("%s: Failed to set rate for flash en.\n", |
| __func__); |
| return rc; |
| } |
| } |
| |
| if (flash_led->gpio_type[FLASH_NOW] == NORMAL_GPIO) { |
| flash_led->flash_now = |
| of_get_named_gpio(node, "qcom,flash-now", 0); |
| if (flash_led->flash_now < 0) { |
| pr_err("Read flash-now property failed. rc = %d\n", |
| flash_led->flash_now); |
| return -EINVAL; |
| } |
| rc = gpio_request(flash_led->flash_now, "FLASH_NOW"); |
| if (rc) { |
| pr_err("%s: Failed to request gpio %d,rc = %d\n", |
| __func__, flash_led->flash_now, rc); |
| return rc; |
| } |
| } else { |
| flash_led->flash_now_clk = |
| devm_clk_get(dev, "flash_now_clk"); |
| if (IS_ERR(flash_led->flash_now_clk)) { |
| pr_err("Failed to get flash-now clk.\n"); |
| return -EINVAL; |
| } |
| |
| flash_led->clk_freq[FLASH_NOW] = |
| clk_round_rate(flash_led->flash_now_clk, |
| flash_led->clk_freq[FLASH_NOW]); |
| rc = clk_set_rate(flash_led->flash_now_clk, |
| flash_led->clk_freq[FLASH_NOW]); |
| if (rc) { |
| pr_err("%s: Failed to set rate for flash now.\n", |
| __func__); |
| return rc; |
| } |
| } |
| |
| /* Configure the duty cycle if need. */ |
| if (flash_led->gpio_type[FLASH_EN] == CLK_GPIO || |
| flash_led->gpio_type[FLASH_NOW] == CLK_GPIO) { |
| rc = of_property_read_u32_array(node, "qcom,duty-cycle", |
| flash_led->duty_cycle, 2); |
| if (!rc && |
| flash_led->duty_cycle[FLASH_EN] >= DUTY_CYCLE_BASE && |
| flash_led->duty_cycle[FLASH_NOW] >= DUTY_CYCLE_BASE) { |
| pr_err("%s: the duty cycle value is invalid.\n", |
| __func__); |
| return -EINVAL; |
| } |
| } |
| |
| /* Based on clk protocol, only RCG clks support duty cycle |
| * configuration, so if the used clk doesn't support set duty |
| * cycle, we use the clk's parent rcg clk to configure the |
| * duty cycle. |
| */ |
| if (flash_led->duty_cycle[FLASH_EN]) { |
| struct clk *flash_en_duty_cycle_clk = NULL; |
| |
| flash_en_duty_cycle_clk = devm_clk_get(dev, |
| "flash_en_duty_cycle_clk"); |
| if (!IS_ERR(flash_en_duty_cycle_clk)) { |
| rc = clk_set_duty_cycle(flash_en_duty_cycle_clk, |
| flash_led->duty_cycle[FLASH_EN], |
| DUTY_CYCLE_BASE); |
| clk_put(flash_en_duty_cycle_clk); |
| } else { |
| rc = clk_set_duty_cycle(flash_led->flash_en_clk, |
| flash_led->duty_cycle[FLASH_EN], |
| DUTY_CYCLE_BASE); |
| } |
| |
| if (rc) { |
| pr_err("Failed to set duty cycle for flash en.\n"); |
| return rc; |
| } |
| } |
| |
| if (flash_led->duty_cycle[FLASH_NOW]) { |
| struct clk *flash_now_duty_cycle_clk = NULL; |
| |
| flash_now_duty_cycle_clk = devm_clk_get(dev, |
| "flash_now_duty_cycle_clk"); |
| if (!IS_ERR(flash_now_duty_cycle_clk)) { |
| rc = clk_set_duty_cycle(flash_now_duty_cycle_clk, |
| flash_led->duty_cycle[FLASH_NOW], |
| DUTY_CYCLE_BASE); |
| clk_put(flash_now_duty_cycle_clk); |
| } else { |
| rc = clk_set_duty_cycle(flash_led->flash_now_clk, |
| flash_led->duty_cycle[FLASH_NOW], |
| DUTY_CYCLE_BASE); |
| } |
| |
| if (rc) { |
| pr_err("Failed to set duty cycle for flash now.\n"); |
| return rc; |
| } |
| } |
| |
| rc = of_property_read_u32_array(node, "qcom,flash-seq-val", |
| array_flash_seq, 2); |
| if (rc < 0) { |
| pr_err("Failed to get flash op seq, rc = %d\n", rc); |
| return rc; |
| } |
| |
| rc = of_property_read_u32_array(node, "qcom,torch-seq-val", |
| array_torch_seq, 2); |
| if (rc < 0) { |
| pr_err("Failed to get torch op seq, rc = %d\n", rc); |
| return rc; |
| } |
| |
| pr_debug("%s: seq: flash: %d, %d torch:%d, %d\n", __func__, |
| array_flash_seq[0], array_flash_seq[1], |
| array_torch_seq[0], array_torch_seq[1]); |
| |
| for (i = 0; i < 2; i++) { |
| rc = of_property_read_string_index(node, |
| "qcom,op-seq", i, |
| &seq_name); |
| CDBG("%s seq_name[%d] = %s\n", __func__, i, |
| seq_name); |
| if (rc < 0) { |
| pr_err("%s failed %d\n", __func__, __LINE__); |
| return rc; |
| } |
| |
| if (!strcmp(seq_name, "flash_en")) { |
| flash_led->ctrl_seq[FLASH_EN].seq_type = |
| FLASH_EN; |
| CDBG("%s:%d seq_type[%d] %d\n", __func__, __LINE__, |
| i, flash_led->ctrl_seq[FLASH_EN].seq_type); |
| if (array_flash_seq[i] == 0) |
| flash_led->ctrl_seq[FLASH_EN].flash_on_val = |
| GPIO_OUT_LOW; |
| else |
| flash_led->ctrl_seq[FLASH_EN].flash_on_val = |
| GPIO_OUT_HIGH; |
| |
| if (array_torch_seq[i] == 0) |
| flash_led->ctrl_seq[FLASH_EN].torch_on_val = |
| GPIO_OUT_LOW; |
| else |
| flash_led->ctrl_seq[FLASH_EN].torch_on_val = |
| GPIO_OUT_HIGH; |
| } else if (!strcmp(seq_name, "flash_now")) { |
| flash_led->ctrl_seq[FLASH_NOW].seq_type = |
| FLASH_NOW; |
| CDBG("%s:%d seq_type[%d] %d\n", __func__, __LINE__, |
| i, flash_led->ctrl_seq[FLASH_NOW].seq_type); |
| if (array_flash_seq[i] == 0) |
| flash_led->ctrl_seq[FLASH_NOW].flash_on_val = |
| GPIO_OUT_LOW; |
| else |
| flash_led->ctrl_seq[FLASH_NOW].flash_on_val = |
| GPIO_OUT_HIGH; |
| |
| if (array_torch_seq[i] == 0) |
| flash_led->ctrl_seq[FLASH_NOW].torch_on_val = |
| GPIO_OUT_LOW; |
| else |
| flash_led->ctrl_seq[FLASH_NOW].torch_on_val = |
| GPIO_OUT_HIGH; |
| } |
| } |
| |
| return rc; |
| } |
| |
| static int led_gpio_flash_probe(struct platform_device *pdev) |
| { |
| int rc = 0; |
| struct led_gpio_flash_data *flash_led = NULL; |
| |
| flash_led = devm_kzalloc(&pdev->dev, sizeof(struct led_gpio_flash_data), |
| GFP_KERNEL); |
| if (flash_led == NULL) |
| return -ENOMEM; |
| |
| flash_led->pinctrl = devm_pinctrl_get(&pdev->dev); |
| if (IS_ERR(flash_led->pinctrl)) { |
| pr_err("%s:failed to get pinctrl\n", __func__); |
| rc = PTR_ERR(flash_led->pinctrl); |
| goto error; |
| } |
| |
| flash_led->gpio_state_default = pinctrl_lookup_state(flash_led->pinctrl, |
| "flash_default"); |
| if (IS_ERR(flash_led->gpio_state_default)) { |
| pr_err("%s:can not get active pinstate\n", __func__); |
| rc = -EINVAL; |
| goto error; |
| } |
| |
| rc = pinctrl_select_state(flash_led->pinctrl, |
| flash_led->gpio_state_default); |
| if (rc) { |
| pr_err("%s:set state failed!\n", __func__); |
| goto error; |
| } |
| |
| rc = led_gpio_get_dt_data(&pdev->dev, flash_led); |
| if (rc) { |
| pr_err("%s: get device tree data failed.\n", |
| __func__); |
| goto error; |
| } |
| |
| /* Add these atomic variables to make sure clk is disabled |
| * just after the clk has been enabled. |
| */ |
| atomic_set(&flash_led->clk_enabled[FLASH_EN], 0); |
| atomic_set(&flash_led->clk_enabled[FLASH_NOW], 0); |
| |
| platform_set_drvdata(pdev, flash_led); |
| flash_led->cdev.max_brightness = LED_FULL; |
| flash_led->cdev.brightness_set = led_gpio_brightness_set; |
| flash_led->cdev.brightness_get = led_gpio_brightness_get; |
| |
| rc = led_classdev_register(&pdev->dev, &flash_led->cdev); |
| if (rc) { |
| pr_err("%s: Failed to register led dev. rc = %d\n", |
| __func__, rc); |
| goto error; |
| } |
| pr_err("%s:probe successfully!\n", __func__); |
| return 0; |
| |
| error: |
| if (flash_led->gpio_type[FLASH_EN] == CLK_GPIO && |
| IS_ERR(flash_led->flash_en_clk)) |
| devm_clk_put(&pdev->dev, flash_led->flash_en_clk); |
| else if (flash_led->gpio_type[FLASH_EN] == NORMAL_GPIO && |
| flash_led->flash_en) |
| gpio_free(flash_led->flash_en); |
| |
| if (flash_led->gpio_type[FLASH_NOW] == CLK_GPIO && |
| IS_ERR(flash_led->flash_now_clk)) |
| devm_clk_put(&pdev->dev, flash_led->flash_now_clk); |
| else if (flash_led->gpio_type[FLASH_NOW] == NORMAL_GPIO && |
| flash_led->flash_now) |
| gpio_free(flash_led->flash_now); |
| |
| if (IS_ERR(flash_led->pinctrl)) |
| devm_pinctrl_put(flash_led->pinctrl); |
| |
| devm_kfree(&pdev->dev, flash_led); |
| return rc; |
| } |
| |
| static int led_gpio_flash_remove(struct platform_device *pdev) |
| { |
| struct led_gpio_flash_data *flash_led = |
| (struct led_gpio_flash_data *)platform_get_drvdata(pdev); |
| if (IS_ERR(flash_led->pinctrl)) |
| devm_pinctrl_put(flash_led->pinctrl); |
| led_classdev_unregister(&flash_led->cdev); |
| devm_kfree(&pdev->dev, flash_led); |
| return 0; |
| } |
| |
| static struct platform_driver led_gpio_flash_driver = { |
| .probe = led_gpio_flash_probe, |
| .remove = led_gpio_flash_remove, |
| .driver = { |
| .name = LED_GPIO_FLASH_DRIVER_NAME, |
| .owner = THIS_MODULE, |
| .of_match_table = led_gpio_flash_of_match, |
| } |
| }; |
| |
| static int __init led_gpio_flash_init(void) |
| { |
| return platform_driver_register(&led_gpio_flash_driver); |
| } |
| |
| static void __exit led_gpio_flash_exit(void) |
| { |
| return platform_driver_unregister(&led_gpio_flash_driver); |
| } |
| |
| late_initcall(led_gpio_flash_init); |
| module_exit(led_gpio_flash_exit); |
| |
| MODULE_DESCRIPTION("QTI GPIO LEDs driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("leds:leds-msm-gpio-flash"); |