blob: 6bc4c064df0baf100641da7c2d727acf8719e616 [file] [log] [blame]
/*
* Copyright (c) 2006 Dave Airlie <airlied@linux.ie>
* Copyright © 2006-2008,2010 Intel Corporation
* Jesse Barnes <jesse.barnes@intel.com>
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice (including the next
* paragraph) shall be included in all copies or substantial portions of the
* Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
* DEALINGS IN THE SOFTWARE.
*
* Authors:
* Eric Anholt <eric@anholt.net>
* Chris Wilson <chris@chris-wilson.co.uk>
*/
#include <linux/i2c.h>
#include <linux/i2c-algo-bit.h>
#include <linux/export.h>
#include <drm/drmP.h>
#include "intel_drv.h"
#include <drm/i915_drm.h>
#include "i915_drv.h"
struct gmbus_pin {
const char *name;
i915_reg_t reg;
};
/* Map gmbus pin pairs to names and registers. */
static const struct gmbus_pin gmbus_pins[] = {
[GMBUS_PIN_SSC] = { "ssc", GPIOB },
[GMBUS_PIN_VGADDC] = { "vga", GPIOA },
[GMBUS_PIN_PANEL] = { "panel", GPIOC },
[GMBUS_PIN_DPC] = { "dpc", GPIOD },
[GMBUS_PIN_DPB] = { "dpb", GPIOE },
[GMBUS_PIN_DPD] = { "dpd", GPIOF },
};
static const struct gmbus_pin gmbus_pins_bdw[] = {
[GMBUS_PIN_VGADDC] = { "vga", GPIOA },
[GMBUS_PIN_DPC] = { "dpc", GPIOD },
[GMBUS_PIN_DPB] = { "dpb", GPIOE },
[GMBUS_PIN_DPD] = { "dpd", GPIOF },
};
static const struct gmbus_pin gmbus_pins_skl[] = {
[GMBUS_PIN_DPC] = { "dpc", GPIOD },
[GMBUS_PIN_DPB] = { "dpb", GPIOE },
[GMBUS_PIN_DPD] = { "dpd", GPIOF },
};
static const struct gmbus_pin gmbus_pins_bxt[] = {
[GMBUS_PIN_1_BXT] = { "dpb", GPIOB },
[GMBUS_PIN_2_BXT] = { "dpc", GPIOC },
[GMBUS_PIN_3_BXT] = { "misc", GPIOD },
};
/* pin is expected to be valid */
static const struct gmbus_pin *get_gmbus_pin(struct drm_i915_private *dev_priv,
unsigned int pin)
{
if (IS_BROXTON(dev_priv))
return &gmbus_pins_bxt[pin];
else if (IS_SKYLAKE(dev_priv) || IS_KABYLAKE(dev_priv))
return &gmbus_pins_skl[pin];
else if (IS_BROADWELL(dev_priv))
return &gmbus_pins_bdw[pin];
else
return &gmbus_pins[pin];
}
bool intel_gmbus_is_valid_pin(struct drm_i915_private *dev_priv,
unsigned int pin)
{
unsigned int size;
if (IS_BROXTON(dev_priv))
size = ARRAY_SIZE(gmbus_pins_bxt);
else if (IS_SKYLAKE(dev_priv) || IS_KABYLAKE(dev_priv))
size = ARRAY_SIZE(gmbus_pins_skl);
else if (IS_BROADWELL(dev_priv))
size = ARRAY_SIZE(gmbus_pins_bdw);
else
size = ARRAY_SIZE(gmbus_pins);
return pin < size &&
i915_mmio_reg_valid(get_gmbus_pin(dev_priv, pin)->reg);
}
/* Intel GPIO access functions */
#define I2C_RISEFALL_TIME 10
static inline struct intel_gmbus *
to_intel_gmbus(struct i2c_adapter *i2c)
{
return container_of(i2c, struct intel_gmbus, adapter);
}
void
intel_i2c_reset(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
I915_WRITE(GMBUS0, 0);
I915_WRITE(GMBUS4, 0);
}
static void intel_i2c_quirk_set(struct drm_i915_private *dev_priv, bool enable)
{
u32 val;
/* When using bit bashing for I2C, this bit needs to be set to 1 */
if (!IS_PINEVIEW(dev_priv))
return;
val = I915_READ(DSPCLK_GATE_D);
if (enable)
val |= DPCUNIT_CLOCK_GATE_DISABLE;
else
val &= ~DPCUNIT_CLOCK_GATE_DISABLE;
I915_WRITE(DSPCLK_GATE_D, val);
}
static u32 get_reserved(struct intel_gmbus *bus)
{
struct drm_i915_private *dev_priv = bus->dev_priv;
struct drm_device *dev = dev_priv->dev;
u32 reserved = 0;
/* On most chips, these bits must be preserved in software. */
if (!IS_I830(dev) && !IS_845G(dev))
reserved = I915_READ_NOTRACE(bus->gpio_reg) &
(GPIO_DATA_PULLUP_DISABLE |
GPIO_CLOCK_PULLUP_DISABLE);
return reserved;
}
static int get_clock(void *data)
{
struct intel_gmbus *bus = data;
struct drm_i915_private *dev_priv = bus->dev_priv;
u32 reserved = get_reserved(bus);
I915_WRITE_NOTRACE(bus->gpio_reg, reserved | GPIO_CLOCK_DIR_MASK);
I915_WRITE_NOTRACE(bus->gpio_reg, reserved);
return (I915_READ_NOTRACE(bus->gpio_reg) & GPIO_CLOCK_VAL_IN) != 0;
}
static int get_data(void *data)
{
struct intel_gmbus *bus = data;
struct drm_i915_private *dev_priv = bus->dev_priv;
u32 reserved = get_reserved(bus);
I915_WRITE_NOTRACE(bus->gpio_reg, reserved | GPIO_DATA_DIR_MASK);
I915_WRITE_NOTRACE(bus->gpio_reg, reserved);
return (I915_READ_NOTRACE(bus->gpio_reg) & GPIO_DATA_VAL_IN) != 0;
}
static void set_clock(void *data, int state_high)
{
struct intel_gmbus *bus = data;
struct drm_i915_private *dev_priv = bus->dev_priv;
u32 reserved = get_reserved(bus);
u32 clock_bits;
if (state_high)
clock_bits = GPIO_CLOCK_DIR_IN | GPIO_CLOCK_DIR_MASK;
else
clock_bits = GPIO_CLOCK_DIR_OUT | GPIO_CLOCK_DIR_MASK |
GPIO_CLOCK_VAL_MASK;
I915_WRITE_NOTRACE(bus->gpio_reg, reserved | clock_bits);
POSTING_READ(bus->gpio_reg);
}
static void set_data(void *data, int state_high)
{
struct intel_gmbus *bus = data;
struct drm_i915_private *dev_priv = bus->dev_priv;
u32 reserved = get_reserved(bus);
u32 data_bits;
if (state_high)
data_bits = GPIO_DATA_DIR_IN | GPIO_DATA_DIR_MASK;
else
data_bits = GPIO_DATA_DIR_OUT | GPIO_DATA_DIR_MASK |
GPIO_DATA_VAL_MASK;
I915_WRITE_NOTRACE(bus->gpio_reg, reserved | data_bits);
POSTING_READ(bus->gpio_reg);
}
static int
intel_gpio_pre_xfer(struct i2c_adapter *adapter)
{
struct intel_gmbus *bus = container_of(adapter,
struct intel_gmbus,
adapter);
struct drm_i915_private *dev_priv = bus->dev_priv;
intel_i2c_reset(dev_priv->dev);
intel_i2c_quirk_set(dev_priv, true);
set_data(bus, 1);
set_clock(bus, 1);
udelay(I2C_RISEFALL_TIME);
return 0;
}
static void
intel_gpio_post_xfer(struct i2c_adapter *adapter)
{
struct intel_gmbus *bus = container_of(adapter,
struct intel_gmbus,
adapter);
struct drm_i915_private *dev_priv = bus->dev_priv;
set_data(bus, 1);
set_clock(bus, 1);
intel_i2c_quirk_set(dev_priv, false);
}
static void
intel_gpio_setup(struct intel_gmbus *bus, unsigned int pin)
{
struct drm_i915_private *dev_priv = bus->dev_priv;
struct i2c_algo_bit_data *algo;
algo = &bus->bit_algo;
bus->gpio_reg = _MMIO(dev_priv->gpio_mmio_base +
i915_mmio_reg_offset(get_gmbus_pin(dev_priv, pin)->reg));
bus->adapter.algo_data = algo;
algo->setsda = set_data;
algo->setscl = set_clock;
algo->getsda = get_data;
algo->getscl = get_clock;
algo->pre_xfer = intel_gpio_pre_xfer;
algo->post_xfer = intel_gpio_post_xfer;
algo->udelay = I2C_RISEFALL_TIME;
algo->timeout = usecs_to_jiffies(2200);
algo->data = bus;
}
static int
gmbus_wait_hw_status(struct drm_i915_private *dev_priv,
u32 gmbus2_status,
u32 gmbus4_irq_en)
{
int i;
u32 gmbus2 = 0;
DEFINE_WAIT(wait);
if (!HAS_GMBUS_IRQ(dev_priv))
gmbus4_irq_en = 0;
/* Important: The hw handles only the first bit, so set only one! Since
* we also need to check for NAKs besides the hw ready/idle signal, we
* need to wake up periodically and check that ourselves. */
I915_WRITE(GMBUS4, gmbus4_irq_en);
for (i = 0; i < msecs_to_jiffies_timeout(50); i++) {
prepare_to_wait(&dev_priv->gmbus_wait_queue, &wait,
TASK_UNINTERRUPTIBLE);
gmbus2 = I915_READ_NOTRACE(GMBUS2);
if (gmbus2 & (GMBUS_SATOER | gmbus2_status))
break;
schedule_timeout(1);
}
finish_wait(&dev_priv->gmbus_wait_queue, &wait);
I915_WRITE(GMBUS4, 0);
if (gmbus2 & GMBUS_SATOER)
return -ENXIO;
if (gmbus2 & gmbus2_status)
return 0;
return -ETIMEDOUT;
}
static int
gmbus_wait_idle(struct drm_i915_private *dev_priv)
{
int ret;
if (!HAS_GMBUS_IRQ(dev_priv))
return intel_wait_for_register(dev_priv,
GMBUS2, GMBUS_ACTIVE, 0,
10);
/* Important: The hw handles only the first bit, so set only one! */
I915_WRITE(GMBUS4, GMBUS_IDLE_EN);
ret = wait_event_timeout(dev_priv->gmbus_wait_queue,
(I915_READ_NOTRACE(GMBUS2) & GMBUS_ACTIVE) == 0,
msecs_to_jiffies_timeout(10));
I915_WRITE(GMBUS4, 0);
if (ret)
return 0;
else
return -ETIMEDOUT;
}
static int
gmbus_xfer_read_chunk(struct drm_i915_private *dev_priv,
unsigned short addr, u8 *buf, unsigned int len,
u32 gmbus1_index)
{
I915_WRITE(GMBUS1,
gmbus1_index |
GMBUS_CYCLE_WAIT |
(len << GMBUS_BYTE_COUNT_SHIFT) |
(addr << GMBUS_SLAVE_ADDR_SHIFT) |
GMBUS_SLAVE_READ | GMBUS_SW_RDY);
while (len) {
int ret;
u32 val, loop = 0;
ret = gmbus_wait_hw_status(dev_priv, GMBUS_HW_RDY,
GMBUS_HW_RDY_EN);
if (ret)
return ret;
val = I915_READ(GMBUS3);
do {
*buf++ = val & 0xff;
val >>= 8;
} while (--len && ++loop < 4);
}
return 0;
}
static int
gmbus_xfer_read(struct drm_i915_private *dev_priv, struct i2c_msg *msg,
u32 gmbus1_index)
{
u8 *buf = msg->buf;
unsigned int rx_size = msg->len;
unsigned int len;
int ret;
do {
len = min(rx_size, GMBUS_BYTE_COUNT_MAX);
ret = gmbus_xfer_read_chunk(dev_priv, msg->addr,
buf, len, gmbus1_index);
if (ret)
return ret;
rx_size -= len;
buf += len;
} while (rx_size != 0);
return 0;
}
static int
gmbus_xfer_write_chunk(struct drm_i915_private *dev_priv,
unsigned short addr, u8 *buf, unsigned int len)
{
unsigned int chunk_size = len;
u32 val, loop;
val = loop = 0;
while (len && loop < 4) {
val |= *buf++ << (8 * loop++);
len -= 1;
}
I915_WRITE(GMBUS3, val);
I915_WRITE(GMBUS1,
GMBUS_CYCLE_WAIT |
(chunk_size << GMBUS_BYTE_COUNT_SHIFT) |
(addr << GMBUS_SLAVE_ADDR_SHIFT) |
GMBUS_SLAVE_WRITE | GMBUS_SW_RDY);
while (len) {
int ret;
val = loop = 0;
do {
val |= *buf++ << (8 * loop);
} while (--len && ++loop < 4);
I915_WRITE(GMBUS3, val);
ret = gmbus_wait_hw_status(dev_priv, GMBUS_HW_RDY,
GMBUS_HW_RDY_EN);
if (ret)
return ret;
}
return 0;
}
static int
gmbus_xfer_write(struct drm_i915_private *dev_priv, struct i2c_msg *msg)
{
u8 *buf = msg->buf;
unsigned int tx_size = msg->len;
unsigned int len;
int ret;
do {
len = min(tx_size, GMBUS_BYTE_COUNT_MAX);
ret = gmbus_xfer_write_chunk(dev_priv, msg->addr, buf, len);
if (ret)
return ret;
buf += len;
tx_size -= len;
} while (tx_size != 0);
return 0;
}
/*
* The gmbus controller can combine a 1 or 2 byte write with a read that
* immediately follows it by using an "INDEX" cycle.
*/
static bool
gmbus_is_index_read(struct i2c_msg *msgs, int i, int num)
{
return (i + 1 < num &&
!(msgs[i].flags & I2C_M_RD) && msgs[i].len <= 2 &&
(msgs[i + 1].flags & I2C_M_RD));
}
static int
gmbus_xfer_index_read(struct drm_i915_private *dev_priv, struct i2c_msg *msgs)
{
u32 gmbus1_index = 0;
u32 gmbus5 = 0;
int ret;
if (msgs[0].len == 2)
gmbus5 = GMBUS_2BYTE_INDEX_EN |
msgs[0].buf[1] | (msgs[0].buf[0] << 8);
if (msgs[0].len == 1)
gmbus1_index = GMBUS_CYCLE_INDEX |
(msgs[0].buf[0] << GMBUS_SLAVE_INDEX_SHIFT);
/* GMBUS5 holds 16-bit index */
if (gmbus5)
I915_WRITE(GMBUS5, gmbus5);
ret = gmbus_xfer_read(dev_priv, &msgs[1], gmbus1_index);
/* Clear GMBUS5 after each index transfer */
if (gmbus5)
I915_WRITE(GMBUS5, 0);
return ret;
}
static int
do_gmbus_xfer(struct i2c_adapter *adapter, struct i2c_msg *msgs, int num)
{
struct intel_gmbus *bus = container_of(adapter,
struct intel_gmbus,
adapter);
struct drm_i915_private *dev_priv = bus->dev_priv;
int i = 0, inc, try = 0;
int ret = 0;
retry:
I915_WRITE(GMBUS0, bus->reg0);
for (; i < num; i += inc) {
inc = 1;
if (gmbus_is_index_read(msgs, i, num)) {
ret = gmbus_xfer_index_read(dev_priv, &msgs[i]);
inc = 2; /* an index read is two msgs */
} else if (msgs[i].flags & I2C_M_RD) {
ret = gmbus_xfer_read(dev_priv, &msgs[i], 0);
} else {
ret = gmbus_xfer_write(dev_priv, &msgs[i]);
}
if (!ret)
ret = gmbus_wait_hw_status(dev_priv, GMBUS_HW_WAIT_PHASE,
GMBUS_HW_WAIT_EN);
if (ret == -ETIMEDOUT)
goto timeout;
else if (ret)
goto clear_err;
}
/* Generate a STOP condition on the bus. Note that gmbus can't generata
* a STOP on the very first cycle. To simplify the code we
* unconditionally generate the STOP condition with an additional gmbus
* cycle. */
I915_WRITE(GMBUS1, GMBUS_CYCLE_STOP | GMBUS_SW_RDY);
/* Mark the GMBUS interface as disabled after waiting for idle.
* We will re-enable it at the start of the next xfer,
* till then let it sleep.
*/
if (gmbus_wait_idle(dev_priv)) {
DRM_DEBUG_KMS("GMBUS [%s] timed out waiting for idle\n",
adapter->name);
ret = -ETIMEDOUT;
}
I915_WRITE(GMBUS0, 0);
ret = ret ?: i;
goto out;
clear_err:
/*
* Wait for bus to IDLE before clearing NAK.
* If we clear the NAK while bus is still active, then it will stay
* active and the next transaction may fail.
*
* If no ACK is received during the address phase of a transaction, the
* adapter must report -ENXIO. It is not clear what to return if no ACK
* is received at other times. But we have to be careful to not return
* spurious -ENXIO because that will prevent i2c and drm edid functions
* from retrying. So return -ENXIO only when gmbus properly quiescents -
* timing out seems to happen when there _is_ a ddc chip present, but
* it's slow responding and only answers on the 2nd retry.
*/
ret = -ENXIO;
if (gmbus_wait_idle(dev_priv)) {
DRM_DEBUG_KMS("GMBUS [%s] timed out after NAK\n",
adapter->name);
ret = -ETIMEDOUT;
}
/* Toggle the Software Clear Interrupt bit. This has the effect
* of resetting the GMBUS controller and so clearing the
* BUS_ERROR raised by the slave's NAK.
*/
I915_WRITE(GMBUS1, GMBUS_SW_CLR_INT);
I915_WRITE(GMBUS1, 0);
I915_WRITE(GMBUS0, 0);
DRM_DEBUG_KMS("GMBUS [%s] NAK for addr: %04x %c(%d)\n",
adapter->name, msgs[i].addr,
(msgs[i].flags & I2C_M_RD) ? 'r' : 'w', msgs[i].len);
/*
* Passive adapters sometimes NAK the first probe. Retry the first
* message once on -ENXIO for GMBUS transfers; the bit banging algorithm
* has retries internally. See also the retry loop in
* drm_do_probe_ddc_edid, which bails out on the first -ENXIO.
*/
if (ret == -ENXIO && i == 0 && try++ == 0) {
DRM_DEBUG_KMS("GMBUS [%s] NAK on first message, retry\n",
adapter->name);
goto retry;
}
goto out;
timeout:
DRM_DEBUG_KMS("GMBUS [%s] timed out, falling back to bit banging on pin %d\n",
bus->adapter.name, bus->reg0 & 0xff);
I915_WRITE(GMBUS0, 0);
/*
* Hardware may not support GMBUS over these pins? Try GPIO bitbanging
* instead. Use EAGAIN to have i2c core retry.
*/
ret = -EAGAIN;
out:
return ret;
}
static int
gmbus_xfer(struct i2c_adapter *adapter, struct i2c_msg *msgs, int num)
{
struct intel_gmbus *bus = container_of(adapter, struct intel_gmbus,
adapter);
struct drm_i915_private *dev_priv = bus->dev_priv;
int ret;
intel_display_power_get(dev_priv, POWER_DOMAIN_GMBUS);
mutex_lock(&dev_priv->gmbus_mutex);
if (bus->force_bit) {
ret = i2c_bit_algo.master_xfer(adapter, msgs, num);
if (ret < 0)
bus->force_bit &= ~GMBUS_FORCE_BIT_RETRY;
} else {
ret = do_gmbus_xfer(adapter, msgs, num);
if (ret == -EAGAIN)
bus->force_bit |= GMBUS_FORCE_BIT_RETRY;
}
mutex_unlock(&dev_priv->gmbus_mutex);
intel_display_power_put(dev_priv, POWER_DOMAIN_GMBUS);
return ret;
}
static u32 gmbus_func(struct i2c_adapter *adapter)
{
return i2c_bit_algo.functionality(adapter) &
(I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL |
/* I2C_FUNC_10BIT_ADDR | */
I2C_FUNC_SMBUS_READ_BLOCK_DATA |
I2C_FUNC_SMBUS_BLOCK_PROC_CALL);
}
static const struct i2c_algorithm gmbus_algorithm = {
.master_xfer = gmbus_xfer,
.functionality = gmbus_func
};
/**
* intel_gmbus_setup - instantiate all Intel i2c GMBuses
* @dev: DRM device
*/
int intel_setup_gmbus(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_gmbus *bus;
unsigned int pin;
int ret;
if (HAS_PCH_NOP(dev))
return 0;
if (IS_VALLEYVIEW(dev) || IS_CHERRYVIEW(dev))
dev_priv->gpio_mmio_base = VLV_DISPLAY_BASE;
else if (!HAS_GMCH_DISPLAY(dev_priv))
dev_priv->gpio_mmio_base =
i915_mmio_reg_offset(PCH_GPIOA) -
i915_mmio_reg_offset(GPIOA);
mutex_init(&dev_priv->gmbus_mutex);
init_waitqueue_head(&dev_priv->gmbus_wait_queue);
for (pin = 0; pin < ARRAY_SIZE(dev_priv->gmbus); pin++) {
if (!intel_gmbus_is_valid_pin(dev_priv, pin))
continue;
bus = &dev_priv->gmbus[pin];
bus->adapter.owner = THIS_MODULE;
bus->adapter.class = I2C_CLASS_DDC;
snprintf(bus->adapter.name,
sizeof(bus->adapter.name),
"i915 gmbus %s",
get_gmbus_pin(dev_priv, pin)->name);
bus->adapter.dev.parent = &dev->pdev->dev;
bus->dev_priv = dev_priv;
bus->adapter.algo = &gmbus_algorithm;
/*
* We wish to retry with bit banging
* after a timed out GMBUS attempt.
*/
bus->adapter.retries = 1;
/* By default use a conservative clock rate */
bus->reg0 = pin | GMBUS_RATE_100KHZ;
/* gmbus seems to be broken on i830 */
if (IS_I830(dev))
bus->force_bit = 1;
intel_gpio_setup(bus, pin);
ret = i2c_add_adapter(&bus->adapter);
if (ret)
goto err;
}
intel_i2c_reset(dev_priv->dev);
return 0;
err:
while (pin--) {
if (!intel_gmbus_is_valid_pin(dev_priv, pin))
continue;
bus = &dev_priv->gmbus[pin];
i2c_del_adapter(&bus->adapter);
}
return ret;
}
struct i2c_adapter *intel_gmbus_get_adapter(struct drm_i915_private *dev_priv,
unsigned int pin)
{
if (WARN_ON(!intel_gmbus_is_valid_pin(dev_priv, pin)))
return NULL;
return &dev_priv->gmbus[pin].adapter;
}
void intel_gmbus_set_speed(struct i2c_adapter *adapter, int speed)
{
struct intel_gmbus *bus = to_intel_gmbus(adapter);
bus->reg0 = (bus->reg0 & ~(0x3 << 8)) | speed;
}
void intel_gmbus_force_bit(struct i2c_adapter *adapter, bool force_bit)
{
struct intel_gmbus *bus = to_intel_gmbus(adapter);
struct drm_i915_private *dev_priv = bus->dev_priv;
mutex_lock(&dev_priv->gmbus_mutex);
bus->force_bit += force_bit ? 1 : -1;
DRM_DEBUG_KMS("%sabling bit-banging on %s. force bit now %d\n",
force_bit ? "en" : "dis", adapter->name,
bus->force_bit);
mutex_unlock(&dev_priv->gmbus_mutex);
}
void intel_teardown_gmbus(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
struct intel_gmbus *bus;
unsigned int pin;
for (pin = 0; pin < ARRAY_SIZE(dev_priv->gmbus); pin++) {
if (!intel_gmbus_is_valid_pin(dev_priv, pin))
continue;
bus = &dev_priv->gmbus[pin];
i2c_del_adapter(&bus->adapter);
}
}