| /* |
| * USB hub driver. |
| * |
| * (C) Copyright 1999 Linus Torvalds |
| * (C) Copyright 1999 Johannes Erdfelt |
| * (C) Copyright 1999 Gregory P. Smith |
| * (C) Copyright 2001 Brad Hards (bhards@bigpond.net.au) |
| * |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/errno.h> |
| #include <linux/module.h> |
| #include <linux/moduleparam.h> |
| #include <linux/completion.h> |
| #include <linux/sched.h> |
| #include <linux/list.h> |
| #include <linux/slab.h> |
| #include <linux/ioctl.h> |
| #include <linux/usb.h> |
| #include <linux/usbdevice_fs.h> |
| #include <linux/kthread.h> |
| #include <linux/mutex.h> |
| #include <linux/freezer.h> |
| |
| #include <asm/uaccess.h> |
| #include <asm/byteorder.h> |
| |
| #include "usb.h" |
| #include "hcd.h" |
| #include "hub.h" |
| |
| /* if we are in debug mode, always announce new devices */ |
| #ifdef DEBUG |
| #ifndef CONFIG_USB_ANNOUNCE_NEW_DEVICES |
| #define CONFIG_USB_ANNOUNCE_NEW_DEVICES |
| #endif |
| #endif |
| |
| struct usb_hub { |
| struct device *intfdev; /* the "interface" device */ |
| struct usb_device *hdev; |
| struct kref kref; |
| struct urb *urb; /* for interrupt polling pipe */ |
| |
| /* buffer for urb ... with extra space in case of babble */ |
| char (*buffer)[8]; |
| dma_addr_t buffer_dma; /* DMA address for buffer */ |
| union { |
| struct usb_hub_status hub; |
| struct usb_port_status port; |
| } *status; /* buffer for status reports */ |
| struct mutex status_mutex; /* for the status buffer */ |
| |
| int error; /* last reported error */ |
| int nerrors; /* track consecutive errors */ |
| |
| struct list_head event_list; /* hubs w/data or errs ready */ |
| unsigned long event_bits[1]; /* status change bitmask */ |
| unsigned long change_bits[1]; /* ports with logical connect |
| status change */ |
| unsigned long busy_bits[1]; /* ports being reset or |
| resumed */ |
| #if USB_MAXCHILDREN > 31 /* 8*sizeof(unsigned long) - 1 */ |
| #error event_bits[] is too short! |
| #endif |
| |
| struct usb_hub_descriptor *descriptor; /* class descriptor */ |
| struct usb_tt tt; /* Transaction Translator */ |
| |
| unsigned mA_per_port; /* current for each child */ |
| |
| unsigned limited_power:1; |
| unsigned quiescing:1; |
| unsigned disconnected:1; |
| |
| unsigned has_indicators:1; |
| u8 indicator[USB_MAXCHILDREN]; |
| struct delayed_work leds; |
| struct delayed_work init_work; |
| void **port_owners; |
| }; |
| |
| |
| /* Protect struct usb_device->state and ->children members |
| * Note: Both are also protected by ->dev.sem, except that ->state can |
| * change to USB_STATE_NOTATTACHED even when the semaphore isn't held. */ |
| static DEFINE_SPINLOCK(device_state_lock); |
| |
| /* khubd's worklist and its lock */ |
| static DEFINE_SPINLOCK(hub_event_lock); |
| static LIST_HEAD(hub_event_list); /* List of hubs needing servicing */ |
| |
| /* Wakes up khubd */ |
| static DECLARE_WAIT_QUEUE_HEAD(khubd_wait); |
| |
| static struct task_struct *khubd_task; |
| |
| /* cycle leds on hubs that aren't blinking for attention */ |
| static int blinkenlights = 0; |
| module_param (blinkenlights, bool, S_IRUGO); |
| MODULE_PARM_DESC (blinkenlights, "true to cycle leds on hubs"); |
| |
| /* |
| * Device SATA8000 FW1.0 from DATAST0R Technology Corp requires about |
| * 10 seconds to send reply for the initial 64-byte descriptor request. |
| */ |
| /* define initial 64-byte descriptor request timeout in milliseconds */ |
| static int initial_descriptor_timeout = USB_CTRL_GET_TIMEOUT; |
| module_param(initial_descriptor_timeout, int, S_IRUGO|S_IWUSR); |
| MODULE_PARM_DESC(initial_descriptor_timeout, |
| "initial 64-byte descriptor request timeout in milliseconds " |
| "(default 5000 - 5.0 seconds)"); |
| |
| /* |
| * As of 2.6.10 we introduce a new USB device initialization scheme which |
| * closely resembles the way Windows works. Hopefully it will be compatible |
| * with a wider range of devices than the old scheme. However some previously |
| * working devices may start giving rise to "device not accepting address" |
| * errors; if that happens the user can try the old scheme by adjusting the |
| * following module parameters. |
| * |
| * For maximum flexibility there are two boolean parameters to control the |
| * hub driver's behavior. On the first initialization attempt, if the |
| * "old_scheme_first" parameter is set then the old scheme will be used, |
| * otherwise the new scheme is used. If that fails and "use_both_schemes" |
| * is set, then the driver will make another attempt, using the other scheme. |
| */ |
| static int old_scheme_first = 0; |
| module_param(old_scheme_first, bool, S_IRUGO | S_IWUSR); |
| MODULE_PARM_DESC(old_scheme_first, |
| "start with the old device initialization scheme"); |
| |
| static int use_both_schemes = 1; |
| module_param(use_both_schemes, bool, S_IRUGO | S_IWUSR); |
| MODULE_PARM_DESC(use_both_schemes, |
| "try the other device initialization scheme if the " |
| "first one fails"); |
| |
| /* Mutual exclusion for EHCI CF initialization. This interferes with |
| * port reset on some companion controllers. |
| */ |
| DECLARE_RWSEM(ehci_cf_port_reset_rwsem); |
| EXPORT_SYMBOL_GPL(ehci_cf_port_reset_rwsem); |
| |
| #define HUB_DEBOUNCE_TIMEOUT 1500 |
| #define HUB_DEBOUNCE_STEP 25 |
| #define HUB_DEBOUNCE_STABLE 100 |
| |
| |
| static int usb_reset_and_verify_device(struct usb_device *udev); |
| |
| static inline char *portspeed(int portstatus) |
| { |
| if (portstatus & (1 << USB_PORT_FEAT_HIGHSPEED)) |
| return "480 Mb/s"; |
| else if (portstatus & (1 << USB_PORT_FEAT_LOWSPEED)) |
| return "1.5 Mb/s"; |
| else if (portstatus & (1 << USB_PORT_FEAT_SUPERSPEED)) |
| return "5.0 Gb/s"; |
| else |
| return "12 Mb/s"; |
| } |
| |
| /* Note that hdev or one of its children must be locked! */ |
| static struct usb_hub *hdev_to_hub(struct usb_device *hdev) |
| { |
| if (!hdev || !hdev->actconfig) |
| return NULL; |
| return usb_get_intfdata(hdev->actconfig->interface[0]); |
| } |
| |
| /* USB 2.0 spec Section 11.24.4.5 */ |
| static int get_hub_descriptor(struct usb_device *hdev, void *data, int size) |
| { |
| int i, ret; |
| |
| for (i = 0; i < 3; i++) { |
| ret = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
| USB_REQ_GET_DESCRIPTOR, USB_DIR_IN | USB_RT_HUB, |
| USB_DT_HUB << 8, 0, data, size, |
| USB_CTRL_GET_TIMEOUT); |
| if (ret >= (USB_DT_HUB_NONVAR_SIZE + 2)) |
| return ret; |
| } |
| return -EINVAL; |
| } |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.1 |
| */ |
| static int clear_hub_feature(struct usb_device *hdev, int feature) |
| { |
| return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), |
| USB_REQ_CLEAR_FEATURE, USB_RT_HUB, feature, 0, NULL, 0, 1000); |
| } |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.2 |
| */ |
| static int clear_port_feature(struct usb_device *hdev, int port1, int feature) |
| { |
| return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), |
| USB_REQ_CLEAR_FEATURE, USB_RT_PORT, feature, port1, |
| NULL, 0, 1000); |
| } |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.13 |
| */ |
| static int set_port_feature(struct usb_device *hdev, int port1, int feature) |
| { |
| return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), |
| USB_REQ_SET_FEATURE, USB_RT_PORT, feature, port1, |
| NULL, 0, 1000); |
| } |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.7.1.10 and table 11-7 |
| * for info about using port indicators |
| */ |
| static void set_port_led( |
| struct usb_hub *hub, |
| int port1, |
| int selector |
| ) |
| { |
| int status = set_port_feature(hub->hdev, (selector << 8) | port1, |
| USB_PORT_FEAT_INDICATOR); |
| if (status < 0) |
| dev_dbg (hub->intfdev, |
| "port %d indicator %s status %d\n", |
| port1, |
| ({ char *s; switch (selector) { |
| case HUB_LED_AMBER: s = "amber"; break; |
| case HUB_LED_GREEN: s = "green"; break; |
| case HUB_LED_OFF: s = "off"; break; |
| case HUB_LED_AUTO: s = "auto"; break; |
| default: s = "??"; break; |
| }; s; }), |
| status); |
| } |
| |
| #define LED_CYCLE_PERIOD ((2*HZ)/3) |
| |
| static void led_work (struct work_struct *work) |
| { |
| struct usb_hub *hub = |
| container_of(work, struct usb_hub, leds.work); |
| struct usb_device *hdev = hub->hdev; |
| unsigned i; |
| unsigned changed = 0; |
| int cursor = -1; |
| |
| if (hdev->state != USB_STATE_CONFIGURED || hub->quiescing) |
| return; |
| |
| for (i = 0; i < hub->descriptor->bNbrPorts; i++) { |
| unsigned selector, mode; |
| |
| /* 30%-50% duty cycle */ |
| |
| switch (hub->indicator[i]) { |
| /* cycle marker */ |
| case INDICATOR_CYCLE: |
| cursor = i; |
| selector = HUB_LED_AUTO; |
| mode = INDICATOR_AUTO; |
| break; |
| /* blinking green = sw attention */ |
| case INDICATOR_GREEN_BLINK: |
| selector = HUB_LED_GREEN; |
| mode = INDICATOR_GREEN_BLINK_OFF; |
| break; |
| case INDICATOR_GREEN_BLINK_OFF: |
| selector = HUB_LED_OFF; |
| mode = INDICATOR_GREEN_BLINK; |
| break; |
| /* blinking amber = hw attention */ |
| case INDICATOR_AMBER_BLINK: |
| selector = HUB_LED_AMBER; |
| mode = INDICATOR_AMBER_BLINK_OFF; |
| break; |
| case INDICATOR_AMBER_BLINK_OFF: |
| selector = HUB_LED_OFF; |
| mode = INDICATOR_AMBER_BLINK; |
| break; |
| /* blink green/amber = reserved */ |
| case INDICATOR_ALT_BLINK: |
| selector = HUB_LED_GREEN; |
| mode = INDICATOR_ALT_BLINK_OFF; |
| break; |
| case INDICATOR_ALT_BLINK_OFF: |
| selector = HUB_LED_AMBER; |
| mode = INDICATOR_ALT_BLINK; |
| break; |
| default: |
| continue; |
| } |
| if (selector != HUB_LED_AUTO) |
| changed = 1; |
| set_port_led(hub, i + 1, selector); |
| hub->indicator[i] = mode; |
| } |
| if (!changed && blinkenlights) { |
| cursor++; |
| cursor %= hub->descriptor->bNbrPorts; |
| set_port_led(hub, cursor + 1, HUB_LED_GREEN); |
| hub->indicator[cursor] = INDICATOR_CYCLE; |
| changed++; |
| } |
| if (changed) |
| schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD); |
| } |
| |
| /* use a short timeout for hub/port status fetches */ |
| #define USB_STS_TIMEOUT 1000 |
| #define USB_STS_RETRIES 5 |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.6 |
| */ |
| static int get_hub_status(struct usb_device *hdev, |
| struct usb_hub_status *data) |
| { |
| int i, status = -ETIMEDOUT; |
| |
| for (i = 0; i < USB_STS_RETRIES && status == -ETIMEDOUT; i++) { |
| status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
| USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_HUB, 0, 0, |
| data, sizeof(*data), USB_STS_TIMEOUT); |
| } |
| return status; |
| } |
| |
| /* |
| * USB 2.0 spec Section 11.24.2.7 |
| */ |
| static int get_port_status(struct usb_device *hdev, int port1, |
| struct usb_port_status *data) |
| { |
| int i, status = -ETIMEDOUT; |
| |
| for (i = 0; i < USB_STS_RETRIES && status == -ETIMEDOUT; i++) { |
| status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
| USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_PORT, 0, port1, |
| data, sizeof(*data), USB_STS_TIMEOUT); |
| } |
| return status; |
| } |
| |
| static int hub_port_status(struct usb_hub *hub, int port1, |
| u16 *status, u16 *change) |
| { |
| int ret; |
| |
| mutex_lock(&hub->status_mutex); |
| ret = get_port_status(hub->hdev, port1, &hub->status->port); |
| if (ret < 4) { |
| dev_err(hub->intfdev, |
| "%s failed (err = %d)\n", __func__, ret); |
| if (ret >= 0) |
| ret = -EIO; |
| } else { |
| *status = le16_to_cpu(hub->status->port.wPortStatus); |
| *change = le16_to_cpu(hub->status->port.wPortChange); |
| ret = 0; |
| } |
| mutex_unlock(&hub->status_mutex); |
| return ret; |
| } |
| |
| static void kick_khubd(struct usb_hub *hub) |
| { |
| unsigned long flags; |
| |
| /* Suppress autosuspend until khubd runs */ |
| atomic_set(&to_usb_interface(hub->intfdev)->pm_usage_cnt, 1); |
| |
| spin_lock_irqsave(&hub_event_lock, flags); |
| if (!hub->disconnected && list_empty(&hub->event_list)) { |
| list_add_tail(&hub->event_list, &hub_event_list); |
| wake_up(&khubd_wait); |
| } |
| spin_unlock_irqrestore(&hub_event_lock, flags); |
| } |
| |
| void usb_kick_khubd(struct usb_device *hdev) |
| { |
| struct usb_hub *hub = hdev_to_hub(hdev); |
| |
| if (hub) |
| kick_khubd(hub); |
| } |
| |
| |
| /* completion function, fires on port status changes and various faults */ |
| static void hub_irq(struct urb *urb) |
| { |
| struct usb_hub *hub = urb->context; |
| int status = urb->status; |
| unsigned i; |
| unsigned long bits; |
| |
| switch (status) { |
| case -ENOENT: /* synchronous unlink */ |
| case -ECONNRESET: /* async unlink */ |
| case -ESHUTDOWN: /* hardware going away */ |
| return; |
| |
| default: /* presumably an error */ |
| /* Cause a hub reset after 10 consecutive errors */ |
| dev_dbg (hub->intfdev, "transfer --> %d\n", status); |
| if ((++hub->nerrors < 10) || hub->error) |
| goto resubmit; |
| hub->error = status; |
| /* FALL THROUGH */ |
| |
| /* let khubd handle things */ |
| case 0: /* we got data: port status changed */ |
| bits = 0; |
| for (i = 0; i < urb->actual_length; ++i) |
| bits |= ((unsigned long) ((*hub->buffer)[i])) |
| << (i*8); |
| hub->event_bits[0] = bits; |
| break; |
| } |
| |
| hub->nerrors = 0; |
| |
| /* Something happened, let khubd figure it out */ |
| kick_khubd(hub); |
| |
| resubmit: |
| if (hub->quiescing) |
| return; |
| |
| if ((status = usb_submit_urb (hub->urb, GFP_ATOMIC)) != 0 |
| && status != -ENODEV && status != -EPERM) |
| dev_err (hub->intfdev, "resubmit --> %d\n", status); |
| } |
| |
| /* USB 2.0 spec Section 11.24.2.3 */ |
| static inline int |
| hub_clear_tt_buffer (struct usb_device *hdev, u16 devinfo, u16 tt) |
| { |
| return usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0), |
| HUB_CLEAR_TT_BUFFER, USB_RT_PORT, devinfo, |
| tt, NULL, 0, 1000); |
| } |
| |
| /* |
| * enumeration blocks khubd for a long time. we use keventd instead, since |
| * long blocking there is the exception, not the rule. accordingly, HCDs |
| * talking to TTs must queue control transfers (not just bulk and iso), so |
| * both can talk to the same hub concurrently. |
| */ |
| static void hub_tt_work(struct work_struct *work) |
| { |
| struct usb_hub *hub = |
| container_of(work, struct usb_hub, tt.clear_work); |
| unsigned long flags; |
| int limit = 100; |
| |
| spin_lock_irqsave (&hub->tt.lock, flags); |
| while (--limit && !list_empty (&hub->tt.clear_list)) { |
| struct list_head *next; |
| struct usb_tt_clear *clear; |
| struct usb_device *hdev = hub->hdev; |
| const struct hc_driver *drv; |
| int status; |
| |
| next = hub->tt.clear_list.next; |
| clear = list_entry (next, struct usb_tt_clear, clear_list); |
| list_del (&clear->clear_list); |
| |
| /* drop lock so HCD can concurrently report other TT errors */ |
| spin_unlock_irqrestore (&hub->tt.lock, flags); |
| status = hub_clear_tt_buffer (hdev, clear->devinfo, clear->tt); |
| if (status) |
| dev_err (&hdev->dev, |
| "clear tt %d (%04x) error %d\n", |
| clear->tt, clear->devinfo, status); |
| |
| /* Tell the HCD, even if the operation failed */ |
| drv = clear->hcd->driver; |
| if (drv->clear_tt_buffer_complete) |
| (drv->clear_tt_buffer_complete)(clear->hcd, clear->ep); |
| |
| kfree(clear); |
| spin_lock_irqsave(&hub->tt.lock, flags); |
| } |
| spin_unlock_irqrestore (&hub->tt.lock, flags); |
| } |
| |
| /** |
| * usb_hub_clear_tt_buffer - clear control/bulk TT state in high speed hub |
| * @urb: an URB associated with the failed or incomplete split transaction |
| * |
| * High speed HCDs use this to tell the hub driver that some split control or |
| * bulk transaction failed in a way that requires clearing internal state of |
| * a transaction translator. This is normally detected (and reported) from |
| * interrupt context. |
| * |
| * It may not be possible for that hub to handle additional full (or low) |
| * speed transactions until that state is fully cleared out. |
| */ |
| int usb_hub_clear_tt_buffer(struct urb *urb) |
| { |
| struct usb_device *udev = urb->dev; |
| int pipe = urb->pipe; |
| struct usb_tt *tt = udev->tt; |
| unsigned long flags; |
| struct usb_tt_clear *clear; |
| |
| /* we've got to cope with an arbitrary number of pending TT clears, |
| * since each TT has "at least two" buffers that can need it (and |
| * there can be many TTs per hub). even if they're uncommon. |
| */ |
| if ((clear = kmalloc (sizeof *clear, GFP_ATOMIC)) == NULL) { |
| dev_err (&udev->dev, "can't save CLEAR_TT_BUFFER state\n"); |
| /* FIXME recover somehow ... RESET_TT? */ |
| return -ENOMEM; |
| } |
| |
| /* info that CLEAR_TT_BUFFER needs */ |
| clear->tt = tt->multi ? udev->ttport : 1; |
| clear->devinfo = usb_pipeendpoint (pipe); |
| clear->devinfo |= udev->devnum << 4; |
| clear->devinfo |= usb_pipecontrol (pipe) |
| ? (USB_ENDPOINT_XFER_CONTROL << 11) |
| : (USB_ENDPOINT_XFER_BULK << 11); |
| if (usb_pipein (pipe)) |
| clear->devinfo |= 1 << 15; |
| |
| /* info for completion callback */ |
| clear->hcd = bus_to_hcd(udev->bus); |
| clear->ep = urb->ep; |
| |
| /* tell keventd to clear state for this TT */ |
| spin_lock_irqsave (&tt->lock, flags); |
| list_add_tail (&clear->clear_list, &tt->clear_list); |
| schedule_work(&tt->clear_work); |
| spin_unlock_irqrestore (&tt->lock, flags); |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(usb_hub_clear_tt_buffer); |
| |
| /* If do_delay is false, return the number of milliseconds the caller |
| * needs to delay. |
| */ |
| static unsigned hub_power_on(struct usb_hub *hub, bool do_delay) |
| { |
| int port1; |
| unsigned pgood_delay = hub->descriptor->bPwrOn2PwrGood * 2; |
| unsigned delay; |
| u16 wHubCharacteristics = |
| le16_to_cpu(hub->descriptor->wHubCharacteristics); |
| |
| /* Enable power on each port. Some hubs have reserved values |
| * of LPSM (> 2) in their descriptors, even though they are |
| * USB 2.0 hubs. Some hubs do not implement port-power switching |
| * but only emulate it. In all cases, the ports won't work |
| * unless we send these messages to the hub. |
| */ |
| if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2) |
| dev_dbg(hub->intfdev, "enabling power on all ports\n"); |
| else |
| dev_dbg(hub->intfdev, "trying to enable port power on " |
| "non-switchable hub\n"); |
| for (port1 = 1; port1 <= hub->descriptor->bNbrPorts; port1++) |
| set_port_feature(hub->hdev, port1, USB_PORT_FEAT_POWER); |
| |
| /* Wait at least 100 msec for power to become stable */ |
| delay = max(pgood_delay, (unsigned) 100); |
| if (do_delay) |
| msleep(delay); |
| return delay; |
| } |
| |
| static int hub_hub_status(struct usb_hub *hub, |
| u16 *status, u16 *change) |
| { |
| int ret; |
| |
| mutex_lock(&hub->status_mutex); |
| ret = get_hub_status(hub->hdev, &hub->status->hub); |
| if (ret < 0) |
| dev_err (hub->intfdev, |
| "%s failed (err = %d)\n", __func__, ret); |
| else { |
| *status = le16_to_cpu(hub->status->hub.wHubStatus); |
| *change = le16_to_cpu(hub->status->hub.wHubChange); |
| ret = 0; |
| } |
| mutex_unlock(&hub->status_mutex); |
| return ret; |
| } |
| |
| static int hub_port_disable(struct usb_hub *hub, int port1, int set_state) |
| { |
| struct usb_device *hdev = hub->hdev; |
| int ret = 0; |
| |
| if (hdev->children[port1-1] && set_state) |
| usb_set_device_state(hdev->children[port1-1], |
| USB_STATE_NOTATTACHED); |
| if (!hub->error) |
| ret = clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE); |
| if (ret) |
| dev_err(hub->intfdev, "cannot disable port %d (err = %d)\n", |
| port1, ret); |
| return ret; |
| } |
| |
| /* |
| * Disable a port and mark a logical connnect-change event, so that some |
| * time later khubd will disconnect() any existing usb_device on the port |
| * and will re-enumerate if there actually is a device attached. |
| */ |
| static void hub_port_logical_disconnect(struct usb_hub *hub, int port1) |
| { |
| dev_dbg(hub->intfdev, "logical disconnect on port %d\n", port1); |
| hub_port_disable(hub, port1, 1); |
| |
| /* FIXME let caller ask to power down the port: |
| * - some devices won't enumerate without a VBUS power cycle |
| * - SRP saves power that way |
| * - ... new call, TBD ... |
| * That's easy if this hub can switch power per-port, and |
| * khubd reactivates the port later (timer, SRP, etc). |
| * Powerdown must be optional, because of reset/DFU. |
| */ |
| |
| set_bit(port1, hub->change_bits); |
| kick_khubd(hub); |
| } |
| |
| enum hub_activation_type { |
| HUB_INIT, HUB_INIT2, HUB_INIT3, |
| HUB_POST_RESET, HUB_RESUME, HUB_RESET_RESUME, |
| }; |
| |
| static void hub_init_func2(struct work_struct *ws); |
| static void hub_init_func3(struct work_struct *ws); |
| |
| static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) |
| { |
| struct usb_device *hdev = hub->hdev; |
| int port1; |
| int status; |
| bool need_debounce_delay = false; |
| unsigned delay; |
| |
| /* Continue a partial initialization */ |
| if (type == HUB_INIT2) |
| goto init2; |
| if (type == HUB_INIT3) |
| goto init3; |
| |
| /* After a resume, port power should still be on. |
| * For any other type of activation, turn it on. |
| */ |
| if (type != HUB_RESUME) { |
| |
| /* Speed up system boot by using a delayed_work for the |
| * hub's initial power-up delays. This is pretty awkward |
| * and the implementation looks like a home-brewed sort of |
| * setjmp/longjmp, but it saves at least 100 ms for each |
| * root hub (assuming usbcore is compiled into the kernel |
| * rather than as a module). It adds up. |
| * |
| * This can't be done for HUB_RESUME or HUB_RESET_RESUME |
| * because for those activation types the ports have to be |
| * operational when we return. In theory this could be done |
| * for HUB_POST_RESET, but it's easier not to. |
| */ |
| if (type == HUB_INIT) { |
| delay = hub_power_on(hub, false); |
| PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func2); |
| schedule_delayed_work(&hub->init_work, |
| msecs_to_jiffies(delay)); |
| |
| /* Suppress autosuspend until init is done */ |
| atomic_set(&to_usb_interface(hub->intfdev)-> |
| pm_usage_cnt, 1); |
| return; /* Continues at init2: below */ |
| } else { |
| hub_power_on(hub, true); |
| } |
| } |
| init2: |
| |
| /* Check each port and set hub->change_bits to let khubd know |
| * which ports need attention. |
| */ |
| for (port1 = 1; port1 <= hdev->maxchild; ++port1) { |
| struct usb_device *udev = hdev->children[port1-1]; |
| u16 portstatus, portchange; |
| |
| portstatus = portchange = 0; |
| status = hub_port_status(hub, port1, &portstatus, &portchange); |
| if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) |
| dev_dbg(hub->intfdev, |
| "port %d: status %04x change %04x\n", |
| port1, portstatus, portchange); |
| |
| /* After anything other than HUB_RESUME (i.e., initialization |
| * or any sort of reset), every port should be disabled. |
| * Unconnected ports should likewise be disabled (paranoia), |
| * and so should ports for which we have no usb_device. |
| */ |
| if ((portstatus & USB_PORT_STAT_ENABLE) && ( |
| type != HUB_RESUME || |
| !(portstatus & USB_PORT_STAT_CONNECTION) || |
| !udev || |
| udev->state == USB_STATE_NOTATTACHED)) { |
| clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE); |
| portstatus &= ~USB_PORT_STAT_ENABLE; |
| } |
| |
| /* Clear status-change flags; we'll debounce later */ |
| if (portchange & USB_PORT_STAT_C_CONNECTION) { |
| need_debounce_delay = true; |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_CONNECTION); |
| } |
| if (portchange & USB_PORT_STAT_C_ENABLE) { |
| need_debounce_delay = true; |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_ENABLE); |
| } |
| |
| if (!udev || udev->state == USB_STATE_NOTATTACHED) { |
| /* Tell khubd to disconnect the device or |
| * check for a new connection |
| */ |
| if (udev || (portstatus & USB_PORT_STAT_CONNECTION)) |
| set_bit(port1, hub->change_bits); |
| |
| } else if (portstatus & USB_PORT_STAT_ENABLE) { |
| /* The power session apparently survived the resume. |
| * If there was an overcurrent or suspend change |
| * (i.e., remote wakeup request), have khubd |
| * take care of it. |
| */ |
| if (portchange) |
| set_bit(port1, hub->change_bits); |
| |
| } else if (udev->persist_enabled) { |
| #ifdef CONFIG_PM |
| udev->reset_resume = 1; |
| #endif |
| set_bit(port1, hub->change_bits); |
| |
| } else { |
| /* The power session is gone; tell khubd */ |
| usb_set_device_state(udev, USB_STATE_NOTATTACHED); |
| set_bit(port1, hub->change_bits); |
| } |
| } |
| |
| /* If no port-status-change flags were set, we don't need any |
| * debouncing. If flags were set we can try to debounce the |
| * ports all at once right now, instead of letting khubd do them |
| * one at a time later on. |
| * |
| * If any port-status changes do occur during this delay, khubd |
| * will see them later and handle them normally. |
| */ |
| if (need_debounce_delay) { |
| delay = HUB_DEBOUNCE_STABLE; |
| |
| /* Don't do a long sleep inside a workqueue routine */ |
| if (type == HUB_INIT2) { |
| PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func3); |
| schedule_delayed_work(&hub->init_work, |
| msecs_to_jiffies(delay)); |
| return; /* Continues at init3: below */ |
| } else { |
| msleep(delay); |
| } |
| } |
| init3: |
| hub->quiescing = 0; |
| |
| status = usb_submit_urb(hub->urb, GFP_NOIO); |
| if (status < 0) |
| dev_err(hub->intfdev, "activate --> %d\n", status); |
| if (hub->has_indicators && blinkenlights) |
| schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD); |
| |
| /* Scan all ports that need attention */ |
| kick_khubd(hub); |
| } |
| |
| /* Implement the continuations for the delays above */ |
| static void hub_init_func2(struct work_struct *ws) |
| { |
| struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work); |
| |
| hub_activate(hub, HUB_INIT2); |
| } |
| |
| static void hub_init_func3(struct work_struct *ws) |
| { |
| struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work); |
| |
| hub_activate(hub, HUB_INIT3); |
| } |
| |
| enum hub_quiescing_type { |
| HUB_DISCONNECT, HUB_PRE_RESET, HUB_SUSPEND |
| }; |
| |
| static void hub_quiesce(struct usb_hub *hub, enum hub_quiescing_type type) |
| { |
| struct usb_device *hdev = hub->hdev; |
| int i; |
| |
| cancel_delayed_work_sync(&hub->init_work); |
| |
| /* khubd and related activity won't re-trigger */ |
| hub->quiescing = 1; |
| |
| if (type != HUB_SUSPEND) { |
| /* Disconnect all the children */ |
| for (i = 0; i < hdev->maxchild; ++i) { |
| if (hdev->children[i]) |
| usb_disconnect(&hdev->children[i]); |
| } |
| } |
| |
| /* Stop khubd and related activity */ |
| usb_kill_urb(hub->urb); |
| if (hub->has_indicators) |
| cancel_delayed_work_sync(&hub->leds); |
| if (hub->tt.hub) |
| cancel_work_sync(&hub->tt.clear_work); |
| } |
| |
| /* caller has locked the hub device */ |
| static int hub_pre_reset(struct usb_interface *intf) |
| { |
| struct usb_hub *hub = usb_get_intfdata(intf); |
| |
| hub_quiesce(hub, HUB_PRE_RESET); |
| return 0; |
| } |
| |
| /* caller has locked the hub device */ |
| static int hub_post_reset(struct usb_interface *intf) |
| { |
| struct usb_hub *hub = usb_get_intfdata(intf); |
| |
| hub_activate(hub, HUB_POST_RESET); |
| return 0; |
| } |
| |
| static int hub_configure(struct usb_hub *hub, |
| struct usb_endpoint_descriptor *endpoint) |
| { |
| struct usb_device *hdev = hub->hdev; |
| struct device *hub_dev = hub->intfdev; |
| u16 hubstatus, hubchange; |
| u16 wHubCharacteristics; |
| unsigned int pipe; |
| int maxp, ret; |
| char *message = "out of memory"; |
| |
| hub->buffer = usb_buffer_alloc(hdev, sizeof(*hub->buffer), GFP_KERNEL, |
| &hub->buffer_dma); |
| if (!hub->buffer) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| |
| hub->status = kmalloc(sizeof(*hub->status), GFP_KERNEL); |
| if (!hub->status) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| mutex_init(&hub->status_mutex); |
| |
| hub->descriptor = kmalloc(sizeof(*hub->descriptor), GFP_KERNEL); |
| if (!hub->descriptor) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| |
| /* Request the entire hub descriptor. |
| * hub->descriptor can handle USB_MAXCHILDREN ports, |
| * but the hub can/will return fewer bytes here. |
| */ |
| ret = get_hub_descriptor(hdev, hub->descriptor, |
| sizeof(*hub->descriptor)); |
| if (ret < 0) { |
| message = "can't read hub descriptor"; |
| goto fail; |
| } else if (hub->descriptor->bNbrPorts > USB_MAXCHILDREN) { |
| message = "hub has too many ports!"; |
| ret = -ENODEV; |
| goto fail; |
| } |
| |
| hdev->maxchild = hub->descriptor->bNbrPorts; |
| dev_info (hub_dev, "%d port%s detected\n", hdev->maxchild, |
| (hdev->maxchild == 1) ? "" : "s"); |
| |
| hub->port_owners = kzalloc(hdev->maxchild * sizeof(void *), GFP_KERNEL); |
| if (!hub->port_owners) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| |
| wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics); |
| |
| if (wHubCharacteristics & HUB_CHAR_COMPOUND) { |
| int i; |
| char portstr [USB_MAXCHILDREN + 1]; |
| |
| for (i = 0; i < hdev->maxchild; i++) |
| portstr[i] = hub->descriptor->DeviceRemovable |
| [((i + 1) / 8)] & (1 << ((i + 1) % 8)) |
| ? 'F' : 'R'; |
| portstr[hdev->maxchild] = 0; |
| dev_dbg(hub_dev, "compound device; port removable status: %s\n", portstr); |
| } else |
| dev_dbg(hub_dev, "standalone hub\n"); |
| |
| switch (wHubCharacteristics & HUB_CHAR_LPSM) { |
| case 0x00: |
| dev_dbg(hub_dev, "ganged power switching\n"); |
| break; |
| case 0x01: |
| dev_dbg(hub_dev, "individual port power switching\n"); |
| break; |
| case 0x02: |
| case 0x03: |
| dev_dbg(hub_dev, "no power switching (usb 1.0)\n"); |
| break; |
| } |
| |
| switch (wHubCharacteristics & HUB_CHAR_OCPM) { |
| case 0x00: |
| dev_dbg(hub_dev, "global over-current protection\n"); |
| break; |
| case 0x08: |
| dev_dbg(hub_dev, "individual port over-current protection\n"); |
| break; |
| case 0x10: |
| case 0x18: |
| dev_dbg(hub_dev, "no over-current protection\n"); |
| break; |
| } |
| |
| spin_lock_init (&hub->tt.lock); |
| INIT_LIST_HEAD (&hub->tt.clear_list); |
| INIT_WORK(&hub->tt.clear_work, hub_tt_work); |
| switch (hdev->descriptor.bDeviceProtocol) { |
| case 0: |
| break; |
| case 1: |
| dev_dbg(hub_dev, "Single TT\n"); |
| hub->tt.hub = hdev; |
| break; |
| case 2: |
| ret = usb_set_interface(hdev, 0, 1); |
| if (ret == 0) { |
| dev_dbg(hub_dev, "TT per port\n"); |
| hub->tt.multi = 1; |
| } else |
| dev_err(hub_dev, "Using single TT (err %d)\n", |
| ret); |
| hub->tt.hub = hdev; |
| break; |
| case 3: |
| /* USB 3.0 hubs don't have a TT */ |
| break; |
| default: |
| dev_dbg(hub_dev, "Unrecognized hub protocol %d\n", |
| hdev->descriptor.bDeviceProtocol); |
| break; |
| } |
| |
| /* Note 8 FS bit times == (8 bits / 12000000 bps) ~= 666ns */ |
| switch (wHubCharacteristics & HUB_CHAR_TTTT) { |
| case HUB_TTTT_8_BITS: |
| if (hdev->descriptor.bDeviceProtocol != 0) { |
| hub->tt.think_time = 666; |
| dev_dbg(hub_dev, "TT requires at most %d " |
| "FS bit times (%d ns)\n", |
| 8, hub->tt.think_time); |
| } |
| break; |
| case HUB_TTTT_16_BITS: |
| hub->tt.think_time = 666 * 2; |
| dev_dbg(hub_dev, "TT requires at most %d " |
| "FS bit times (%d ns)\n", |
| 16, hub->tt.think_time); |
| break; |
| case HUB_TTTT_24_BITS: |
| hub->tt.think_time = 666 * 3; |
| dev_dbg(hub_dev, "TT requires at most %d " |
| "FS bit times (%d ns)\n", |
| 24, hub->tt.think_time); |
| break; |
| case HUB_TTTT_32_BITS: |
| hub->tt.think_time = 666 * 4; |
| dev_dbg(hub_dev, "TT requires at most %d " |
| "FS bit times (%d ns)\n", |
| 32, hub->tt.think_time); |
| break; |
| } |
| |
| /* probe() zeroes hub->indicator[] */ |
| if (wHubCharacteristics & HUB_CHAR_PORTIND) { |
| hub->has_indicators = 1; |
| dev_dbg(hub_dev, "Port indicators are supported\n"); |
| } |
| |
| dev_dbg(hub_dev, "power on to power good time: %dms\n", |
| hub->descriptor->bPwrOn2PwrGood * 2); |
| |
| /* power budgeting mostly matters with bus-powered hubs, |
| * and battery-powered root hubs (may provide just 8 mA). |
| */ |
| ret = usb_get_status(hdev, USB_RECIP_DEVICE, 0, &hubstatus); |
| if (ret < 2) { |
| message = "can't get hub status"; |
| goto fail; |
| } |
| le16_to_cpus(&hubstatus); |
| if (hdev == hdev->bus->root_hub) { |
| if (hdev->bus_mA == 0 || hdev->bus_mA >= 500) |
| hub->mA_per_port = 500; |
| else { |
| hub->mA_per_port = hdev->bus_mA; |
| hub->limited_power = 1; |
| } |
| } else if ((hubstatus & (1 << USB_DEVICE_SELF_POWERED)) == 0) { |
| dev_dbg(hub_dev, "hub controller current requirement: %dmA\n", |
| hub->descriptor->bHubContrCurrent); |
| hub->limited_power = 1; |
| if (hdev->maxchild > 0) { |
| int remaining = hdev->bus_mA - |
| hub->descriptor->bHubContrCurrent; |
| |
| if (remaining < hdev->maxchild * 100) |
| dev_warn(hub_dev, |
| "insufficient power available " |
| "to use all downstream ports\n"); |
| hub->mA_per_port = 100; /* 7.2.1.1 */ |
| } |
| } else { /* Self-powered external hub */ |
| /* FIXME: What about battery-powered external hubs that |
| * provide less current per port? */ |
| hub->mA_per_port = 500; |
| } |
| if (hub->mA_per_port < 500) |
| dev_dbg(hub_dev, "%umA bus power budget for each child\n", |
| hub->mA_per_port); |
| |
| ret = hub_hub_status(hub, &hubstatus, &hubchange); |
| if (ret < 0) { |
| message = "can't get hub status"; |
| goto fail; |
| } |
| |
| /* local power status reports aren't always correct */ |
| if (hdev->actconfig->desc.bmAttributes & USB_CONFIG_ATT_SELFPOWER) |
| dev_dbg(hub_dev, "local power source is %s\n", |
| (hubstatus & HUB_STATUS_LOCAL_POWER) |
| ? "lost (inactive)" : "good"); |
| |
| if ((wHubCharacteristics & HUB_CHAR_OCPM) == 0) |
| dev_dbg(hub_dev, "%sover-current condition exists\n", |
| (hubstatus & HUB_STATUS_OVERCURRENT) ? "" : "no "); |
| |
| /* set up the interrupt endpoint |
| * We use the EP's maxpacket size instead of (PORTS+1+7)/8 |
| * bytes as USB2.0[11.12.3] says because some hubs are known |
| * to send more data (and thus cause overflow). For root hubs, |
| * maxpktsize is defined in hcd.c's fake endpoint descriptors |
| * to be big enough for at least USB_MAXCHILDREN ports. */ |
| pipe = usb_rcvintpipe(hdev, endpoint->bEndpointAddress); |
| maxp = usb_maxpacket(hdev, pipe, usb_pipeout(pipe)); |
| |
| if (maxp > sizeof(*hub->buffer)) |
| maxp = sizeof(*hub->buffer); |
| |
| hub->urb = usb_alloc_urb(0, GFP_KERNEL); |
| if (!hub->urb) { |
| ret = -ENOMEM; |
| goto fail; |
| } |
| |
| usb_fill_int_urb(hub->urb, hdev, pipe, *hub->buffer, maxp, hub_irq, |
| hub, endpoint->bInterval); |
| hub->urb->transfer_dma = hub->buffer_dma; |
| hub->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; |
| |
| /* maybe cycle the hub leds */ |
| if (hub->has_indicators && blinkenlights) |
| hub->indicator [0] = INDICATOR_CYCLE; |
| |
| hub_activate(hub, HUB_INIT); |
| return 0; |
| |
| fail: |
| dev_err (hub_dev, "config failed, %s (err %d)\n", |
| message, ret); |
| /* hub_disconnect() frees urb and descriptor */ |
| return ret; |
| } |
| |
| static void hub_release(struct kref *kref) |
| { |
| struct usb_hub *hub = container_of(kref, struct usb_hub, kref); |
| |
| usb_put_intf(to_usb_interface(hub->intfdev)); |
| kfree(hub); |
| } |
| |
| static unsigned highspeed_hubs; |
| |
| static void hub_disconnect(struct usb_interface *intf) |
| { |
| struct usb_hub *hub = usb_get_intfdata (intf); |
| |
| /* Take the hub off the event list and don't let it be added again */ |
| spin_lock_irq(&hub_event_lock); |
| list_del_init(&hub->event_list); |
| hub->disconnected = 1; |
| spin_unlock_irq(&hub_event_lock); |
| |
| /* Disconnect all children and quiesce the hub */ |
| hub->error = 0; |
| hub_quiesce(hub, HUB_DISCONNECT); |
| |
| usb_set_intfdata (intf, NULL); |
| hub->hdev->maxchild = 0; |
| |
| if (hub->hdev->speed == USB_SPEED_HIGH) |
| highspeed_hubs--; |
| |
| usb_free_urb(hub->urb); |
| kfree(hub->port_owners); |
| kfree(hub->descriptor); |
| kfree(hub->status); |
| usb_buffer_free(hub->hdev, sizeof(*hub->buffer), hub->buffer, |
| hub->buffer_dma); |
| |
| kref_put(&hub->kref, hub_release); |
| } |
| |
| static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id) |
| { |
| struct usb_host_interface *desc; |
| struct usb_endpoint_descriptor *endpoint; |
| struct usb_device *hdev; |
| struct usb_hub *hub; |
| |
| desc = intf->cur_altsetting; |
| hdev = interface_to_usbdev(intf); |
| |
| if (hdev->level == MAX_TOPO_LEVEL) { |
| dev_err(&intf->dev, |
| "Unsupported bus topology: hub nested too deep\n"); |
| return -E2BIG; |
| } |
| |
| #ifdef CONFIG_USB_OTG_BLACKLIST_HUB |
| if (hdev->parent) { |
| dev_warn(&intf->dev, "ignoring external hub\n"); |
| return -ENODEV; |
| } |
| #endif |
| |
| /* Some hubs have a subclass of 1, which AFAICT according to the */ |
| /* specs is not defined, but it works */ |
| if ((desc->desc.bInterfaceSubClass != 0) && |
| (desc->desc.bInterfaceSubClass != 1)) { |
| descriptor_error: |
| dev_err (&intf->dev, "bad descriptor, ignoring hub\n"); |
| return -EIO; |
| } |
| |
| /* Multiple endpoints? What kind of mutant ninja-hub is this? */ |
| if (desc->desc.bNumEndpoints != 1) |
| goto descriptor_error; |
| |
| endpoint = &desc->endpoint[0].desc; |
| |
| /* If it's not an interrupt in endpoint, we'd better punt! */ |
| if (!usb_endpoint_is_int_in(endpoint)) |
| goto descriptor_error; |
| |
| /* We found a hub */ |
| dev_info (&intf->dev, "USB hub found\n"); |
| |
| hub = kzalloc(sizeof(*hub), GFP_KERNEL); |
| if (!hub) { |
| dev_dbg (&intf->dev, "couldn't kmalloc hub struct\n"); |
| return -ENOMEM; |
| } |
| |
| kref_init(&hub->kref); |
| INIT_LIST_HEAD(&hub->event_list); |
| hub->intfdev = &intf->dev; |
| hub->hdev = hdev; |
| INIT_DELAYED_WORK(&hub->leds, led_work); |
| INIT_DELAYED_WORK(&hub->init_work, NULL); |
| usb_get_intf(intf); |
| |
| usb_set_intfdata (intf, hub); |
| intf->needs_remote_wakeup = 1; |
| |
| if (hdev->speed == USB_SPEED_HIGH) |
| highspeed_hubs++; |
| |
| if (hub_configure(hub, endpoint) >= 0) |
| return 0; |
| |
| hub_disconnect (intf); |
| return -ENODEV; |
| } |
| |
| static int |
| hub_ioctl(struct usb_interface *intf, unsigned int code, void *user_data) |
| { |
| struct usb_device *hdev = interface_to_usbdev (intf); |
| |
| /* assert ifno == 0 (part of hub spec) */ |
| switch (code) { |
| case USBDEVFS_HUB_PORTINFO: { |
| struct usbdevfs_hub_portinfo *info = user_data; |
| int i; |
| |
| spin_lock_irq(&device_state_lock); |
| if (hdev->devnum <= 0) |
| info->nports = 0; |
| else { |
| info->nports = hdev->maxchild; |
| for (i = 0; i < info->nports; i++) { |
| if (hdev->children[i] == NULL) |
| info->port[i] = 0; |
| else |
| info->port[i] = |
| hdev->children[i]->devnum; |
| } |
| } |
| spin_unlock_irq(&device_state_lock); |
| |
| return info->nports + 1; |
| } |
| |
| default: |
| return -ENOSYS; |
| } |
| } |
| |
| /* |
| * Allow user programs to claim ports on a hub. When a device is attached |
| * to one of these "claimed" ports, the program will "own" the device. |
| */ |
| static int find_port_owner(struct usb_device *hdev, unsigned port1, |
| void ***ppowner) |
| { |
| if (hdev->state == USB_STATE_NOTATTACHED) |
| return -ENODEV; |
| if (port1 == 0 || port1 > hdev->maxchild) |
| return -EINVAL; |
| |
| /* This assumes that devices not managed by the hub driver |
| * will always have maxchild equal to 0. |
| */ |
| *ppowner = &(hdev_to_hub(hdev)->port_owners[port1 - 1]); |
| return 0; |
| } |
| |
| /* In the following three functions, the caller must hold hdev's lock */ |
| int usb_hub_claim_port(struct usb_device *hdev, unsigned port1, void *owner) |
| { |
| int rc; |
| void **powner; |
| |
| rc = find_port_owner(hdev, port1, &powner); |
| if (rc) |
| return rc; |
| if (*powner) |
| return -EBUSY; |
| *powner = owner; |
| return rc; |
| } |
| |
| int usb_hub_release_port(struct usb_device *hdev, unsigned port1, void *owner) |
| { |
| int rc; |
| void **powner; |
| |
| rc = find_port_owner(hdev, port1, &powner); |
| if (rc) |
| return rc; |
| if (*powner != owner) |
| return -ENOENT; |
| *powner = NULL; |
| return rc; |
| } |
| |
| void usb_hub_release_all_ports(struct usb_device *hdev, void *owner) |
| { |
| int n; |
| void **powner; |
| |
| n = find_port_owner(hdev, 1, &powner); |
| if (n == 0) { |
| for (; n < hdev->maxchild; (++n, ++powner)) { |
| if (*powner == owner) |
| *powner = NULL; |
| } |
| } |
| } |
| |
| /* The caller must hold udev's lock */ |
| bool usb_device_is_owned(struct usb_device *udev) |
| { |
| struct usb_hub *hub; |
| |
| if (udev->state == USB_STATE_NOTATTACHED || !udev->parent) |
| return false; |
| hub = hdev_to_hub(udev->parent); |
| return !!hub->port_owners[udev->portnum - 1]; |
| } |
| |
| |
| static void recursively_mark_NOTATTACHED(struct usb_device *udev) |
| { |
| int i; |
| |
| for (i = 0; i < udev->maxchild; ++i) { |
| if (udev->children[i]) |
| recursively_mark_NOTATTACHED(udev->children[i]); |
| } |
| if (udev->state == USB_STATE_SUSPENDED) { |
| udev->discon_suspended = 1; |
| udev->active_duration -= jiffies; |
| } |
| udev->state = USB_STATE_NOTATTACHED; |
| } |
| |
| /** |
| * usb_set_device_state - change a device's current state (usbcore, hcds) |
| * @udev: pointer to device whose state should be changed |
| * @new_state: new state value to be stored |
| * |
| * udev->state is _not_ fully protected by the device lock. Although |
| * most transitions are made only while holding the lock, the state can |
| * can change to USB_STATE_NOTATTACHED at almost any time. This |
| * is so that devices can be marked as disconnected as soon as possible, |
| * without having to wait for any semaphores to be released. As a result, |
| * all changes to any device's state must be protected by the |
| * device_state_lock spinlock. |
| * |
| * Once a device has been added to the device tree, all changes to its state |
| * should be made using this routine. The state should _not_ be set directly. |
| * |
| * If udev->state is already USB_STATE_NOTATTACHED then no change is made. |
| * Otherwise udev->state is set to new_state, and if new_state is |
| * USB_STATE_NOTATTACHED then all of udev's descendants' states are also set |
| * to USB_STATE_NOTATTACHED. |
| */ |
| void usb_set_device_state(struct usb_device *udev, |
| enum usb_device_state new_state) |
| { |
| unsigned long flags; |
| |
| spin_lock_irqsave(&device_state_lock, flags); |
| if (udev->state == USB_STATE_NOTATTACHED) |
| ; /* do nothing */ |
| else if (new_state != USB_STATE_NOTATTACHED) { |
| |
| /* root hub wakeup capabilities are managed out-of-band |
| * and may involve silicon errata ... ignore them here. |
| */ |
| if (udev->parent) { |
| if (udev->state == USB_STATE_SUSPENDED |
| || new_state == USB_STATE_SUSPENDED) |
| ; /* No change to wakeup settings */ |
| else if (new_state == USB_STATE_CONFIGURED) |
| device_init_wakeup(&udev->dev, |
| (udev->actconfig->desc.bmAttributes |
| & USB_CONFIG_ATT_WAKEUP)); |
| else |
| device_init_wakeup(&udev->dev, 0); |
| } |
| if (udev->state == USB_STATE_SUSPENDED && |
| new_state != USB_STATE_SUSPENDED) |
| udev->active_duration -= jiffies; |
| else if (new_state == USB_STATE_SUSPENDED && |
| udev->state != USB_STATE_SUSPENDED) |
| udev->active_duration += jiffies; |
| udev->state = new_state; |
| } else |
| recursively_mark_NOTATTACHED(udev); |
| spin_unlock_irqrestore(&device_state_lock, flags); |
| } |
| EXPORT_SYMBOL_GPL(usb_set_device_state); |
| |
| /* |
| * WUSB devices are simple: they have no hubs behind, so the mapping |
| * device <-> virtual port number becomes 1:1. Why? to simplify the |
| * life of the device connection logic in |
| * drivers/usb/wusbcore/devconnect.c. When we do the initial secret |
| * handshake we need to assign a temporary address in the unauthorized |
| * space. For simplicity we use the first virtual port number found to |
| * be free [drivers/usb/wusbcore/devconnect.c:wusbhc_devconnect_ack()] |
| * and that becomes it's address [X < 128] or its unauthorized address |
| * [X | 0x80]. |
| * |
| * We add 1 as an offset to the one-based USB-stack port number |
| * (zero-based wusb virtual port index) for two reasons: (a) dev addr |
| * 0 is reserved by USB for default address; (b) Linux's USB stack |
| * uses always #1 for the root hub of the controller. So USB stack's |
| * port #1, which is wusb virtual-port #0 has address #2. |
| * |
| * Devices connected under xHCI are not as simple. The host controller |
| * supports virtualization, so the hardware assigns device addresses and |
| * the HCD must setup data structures before issuing a set address |
| * command to the hardware. |
| */ |
| static void choose_address(struct usb_device *udev) |
| { |
| int devnum; |
| struct usb_bus *bus = udev->bus; |
| |
| /* If khubd ever becomes multithreaded, this will need a lock */ |
| if (udev->wusb) { |
| devnum = udev->portnum + 1; |
| BUG_ON(test_bit(devnum, bus->devmap.devicemap)); |
| } else { |
| /* Try to allocate the next devnum beginning at |
| * bus->devnum_next. */ |
| devnum = find_next_zero_bit(bus->devmap.devicemap, 128, |
| bus->devnum_next); |
| if (devnum >= 128) |
| devnum = find_next_zero_bit(bus->devmap.devicemap, |
| 128, 1); |
| bus->devnum_next = ( devnum >= 127 ? 1 : devnum + 1); |
| } |
| if (devnum < 128) { |
| set_bit(devnum, bus->devmap.devicemap); |
| udev->devnum = devnum; |
| } |
| } |
| |
| static void release_address(struct usb_device *udev) |
| { |
| if (udev->devnum > 0) { |
| clear_bit(udev->devnum, udev->bus->devmap.devicemap); |
| udev->devnum = -1; |
| } |
| } |
| |
| static void update_address(struct usb_device *udev, int devnum) |
| { |
| /* The address for a WUSB device is managed by wusbcore. */ |
| if (!udev->wusb) |
| udev->devnum = devnum; |
| } |
| |
| #ifdef CONFIG_USB_SUSPEND |
| |
| static void usb_stop_pm(struct usb_device *udev) |
| { |
| /* Synchronize with the ksuspend thread to prevent any more |
| * autosuspend requests from being submitted, and decrement |
| * the parent's count of unsuspended children. |
| */ |
| usb_pm_lock(udev); |
| if (udev->parent && !udev->discon_suspended) |
| usb_autosuspend_device(udev->parent); |
| usb_pm_unlock(udev); |
| |
| /* Stop any autosuspend or autoresume requests already submitted */ |
| cancel_delayed_work_sync(&udev->autosuspend); |
| cancel_work_sync(&udev->autoresume); |
| } |
| |
| #else |
| |
| static inline void usb_stop_pm(struct usb_device *udev) |
| { } |
| |
| #endif |
| |
| /** |
| * usb_disconnect - disconnect a device (usbcore-internal) |
| * @pdev: pointer to device being disconnected |
| * Context: !in_interrupt () |
| * |
| * Something got disconnected. Get rid of it and all of its children. |
| * |
| * If *pdev is a normal device then the parent hub must already be locked. |
| * If *pdev is a root hub then this routine will acquire the |
| * usb_bus_list_lock on behalf of the caller. |
| * |
| * Only hub drivers (including virtual root hub drivers for host |
| * controllers) should ever call this. |
| * |
| * This call is synchronous, and may not be used in an interrupt context. |
| */ |
| void usb_disconnect(struct usb_device **pdev) |
| { |
| struct usb_device *udev = *pdev; |
| int i; |
| |
| if (!udev) { |
| pr_debug ("%s nodev\n", __func__); |
| return; |
| } |
| |
| /* mark the device as inactive, so any further urb submissions for |
| * this device (and any of its children) will fail immediately. |
| * this quiesces everyting except pending urbs. |
| */ |
| usb_set_device_state(udev, USB_STATE_NOTATTACHED); |
| dev_info (&udev->dev, "USB disconnect, address %d\n", udev->devnum); |
| |
| usb_lock_device(udev); |
| |
| /* Free up all the children before we remove this device */ |
| for (i = 0; i < USB_MAXCHILDREN; i++) { |
| if (udev->children[i]) |
| usb_disconnect(&udev->children[i]); |
| } |
| |
| /* deallocate hcd/hardware state ... nuking all pending urbs and |
| * cleaning up all state associated with the current configuration |
| * so that the hardware is now fully quiesced. |
| */ |
| dev_dbg (&udev->dev, "unregistering device\n"); |
| usb_disable_device(udev, 0); |
| usb_hcd_synchronize_unlinks(udev); |
| |
| usb_remove_ep_devs(&udev->ep0); |
| usb_unlock_device(udev); |
| |
| /* Unregister the device. The device driver is responsible |
| * for de-configuring the device and invoking the remove-device |
| * notifier chain (used by usbfs and possibly others). |
| */ |
| device_del(&udev->dev); |
| |
| /* Free the device number and delete the parent's children[] |
| * (or root_hub) pointer. |
| */ |
| release_address(udev); |
| |
| /* Avoid races with recursively_mark_NOTATTACHED() */ |
| spin_lock_irq(&device_state_lock); |
| *pdev = NULL; |
| spin_unlock_irq(&device_state_lock); |
| |
| usb_stop_pm(udev); |
| |
| put_device(&udev->dev); |
| } |
| |
| #ifdef CONFIG_USB_ANNOUNCE_NEW_DEVICES |
| static void show_string(struct usb_device *udev, char *id, char *string) |
| { |
| if (!string) |
| return; |
| dev_printk(KERN_INFO, &udev->dev, "%s: %s\n", id, string); |
| } |
| |
| static void announce_device(struct usb_device *udev) |
| { |
| dev_info(&udev->dev, "New USB device found, idVendor=%04x, idProduct=%04x\n", |
| le16_to_cpu(udev->descriptor.idVendor), |
| le16_to_cpu(udev->descriptor.idProduct)); |
| dev_info(&udev->dev, |
| "New USB device strings: Mfr=%d, Product=%d, SerialNumber=%d\n", |
| udev->descriptor.iManufacturer, |
| udev->descriptor.iProduct, |
| udev->descriptor.iSerialNumber); |
| show_string(udev, "Product", udev->product); |
| show_string(udev, "Manufacturer", udev->manufacturer); |
| show_string(udev, "SerialNumber", udev->serial); |
| } |
| #else |
| static inline void announce_device(struct usb_device *udev) { } |
| #endif |
| |
| #ifdef CONFIG_USB_OTG |
| #include "otg_whitelist.h" |
| #endif |
| |
| /** |
| * usb_configure_device_otg - FIXME (usbcore-internal) |
| * @udev: newly addressed device (in ADDRESS state) |
| * |
| * Do configuration for On-The-Go devices |
| */ |
| static int usb_configure_device_otg(struct usb_device *udev) |
| { |
| int err = 0; |
| |
| #ifdef CONFIG_USB_OTG |
| /* |
| * OTG-aware devices on OTG-capable root hubs may be able to use SRP, |
| * to wake us after we've powered off VBUS; and HNP, switching roles |
| * "host" to "peripheral". The OTG descriptor helps figure this out. |
| */ |
| if (!udev->bus->is_b_host |
| && udev->config |
| && udev->parent == udev->bus->root_hub) { |
| struct usb_otg_descriptor *desc = 0; |
| struct usb_bus *bus = udev->bus; |
| |
| /* descriptor may appear anywhere in config */ |
| if (__usb_get_extra_descriptor (udev->rawdescriptors[0], |
| le16_to_cpu(udev->config[0].desc.wTotalLength), |
| USB_DT_OTG, (void **) &desc) == 0) { |
| if (desc->bmAttributes & USB_OTG_HNP) { |
| unsigned port1 = udev->portnum; |
| |
| dev_info(&udev->dev, |
| "Dual-Role OTG device on %sHNP port\n", |
| (port1 == bus->otg_port) |
| ? "" : "non-"); |
| |
| /* enable HNP before suspend, it's simpler */ |
| if (port1 == bus->otg_port) |
| bus->b_hnp_enable = 1; |
| err = usb_control_msg(udev, |
| usb_sndctrlpipe(udev, 0), |
| USB_REQ_SET_FEATURE, 0, |
| bus->b_hnp_enable |
| ? USB_DEVICE_B_HNP_ENABLE |
| : USB_DEVICE_A_ALT_HNP_SUPPORT, |
| 0, NULL, 0, USB_CTRL_SET_TIMEOUT); |
| if (err < 0) { |
| /* OTG MESSAGE: report errors here, |
| * customize to match your product. |
| */ |
| dev_info(&udev->dev, |
| "can't set HNP mode: %d\n", |
| err); |
| bus->b_hnp_enable = 0; |
| } |
| } |
| } |
| } |
| |
| if (!is_targeted(udev)) { |
| |
| /* Maybe it can talk to us, though we can't talk to it. |
| * (Includes HNP test device.) |
| */ |
| if (udev->bus->b_hnp_enable || udev->bus->is_b_host) { |
| err = usb_port_suspend(udev, PMSG_SUSPEND); |
| if (err < 0) |
| dev_dbg(&udev->dev, "HNP fail, %d\n", err); |
| } |
| err = -ENOTSUPP; |
| goto fail; |
| } |
| fail: |
| #endif |
| return err; |
| } |
| |
| |
| /** |
| * usb_configure_device - Detect and probe device intfs/otg (usbcore-internal) |
| * @udev: newly addressed device (in ADDRESS state) |
| * |
| * This is only called by usb_new_device() and usb_authorize_device() |
| * and FIXME -- all comments that apply to them apply here wrt to |
| * environment. |
| * |
| * If the device is WUSB and not authorized, we don't attempt to read |
| * the string descriptors, as they will be errored out by the device |
| * until it has been authorized. |
| */ |
| static int usb_configure_device(struct usb_device *udev) |
| { |
| int err; |
| |
| if (udev->config == NULL) { |
| err = usb_get_configuration(udev); |
| if (err < 0) { |
| dev_err(&udev->dev, "can't read configurations, error %d\n", |
| err); |
| goto fail; |
| } |
| } |
| if (udev->wusb == 1 && udev->authorized == 0) { |
| udev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| udev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| udev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| } |
| else { |
| /* read the standard strings and cache them if present */ |
| udev->product = usb_cache_string(udev, udev->descriptor.iProduct); |
| udev->manufacturer = usb_cache_string(udev, |
| udev->descriptor.iManufacturer); |
| udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber); |
| } |
| err = usb_configure_device_otg(udev); |
| fail: |
| return err; |
| } |
| |
| |
| /** |
| * usb_new_device - perform initial device setup (usbcore-internal) |
| * @udev: newly addressed device (in ADDRESS state) |
| * |
| * This is called with devices which have been enumerated, but not yet |
| * configured. The device descriptor is available, but not descriptors |
| * for any device configuration. The caller must have locked either |
| * the parent hub (if udev is a normal device) or else the |
| * usb_bus_list_lock (if udev is a root hub). The parent's pointer to |
| * udev has already been installed, but udev is not yet visible through |
| * sysfs or other filesystem code. |
| * |
| * It will return if the device is configured properly or not. Zero if |
| * the interface was registered with the driver core; else a negative |
| * errno value. |
| * |
| * This call is synchronous, and may not be used in an interrupt context. |
| * |
| * Only the hub driver or root-hub registrar should ever call this. |
| */ |
| int usb_new_device(struct usb_device *udev) |
| { |
| int err; |
| |
| /* Increment the parent's count of unsuspended children */ |
| if (udev->parent) |
| usb_autoresume_device(udev->parent); |
| |
| usb_detect_quirks(udev); /* Determine quirks */ |
| err = usb_configure_device(udev); /* detect & probe dev/intfs */ |
| if (err < 0) |
| goto fail; |
| dev_dbg(&udev->dev, "udev %d, busnum %d, minor = %d\n", |
| udev->devnum, udev->bus->busnum, |
| (((udev->bus->busnum-1) * 128) + (udev->devnum-1))); |
| /* export the usbdev device-node for libusb */ |
| udev->dev.devt = MKDEV(USB_DEVICE_MAJOR, |
| (((udev->bus->busnum-1) * 128) + (udev->devnum-1))); |
| |
| /* Tell the world! */ |
| announce_device(udev); |
| |
| /* Register the device. The device driver is responsible |
| * for configuring the device and invoking the add-device |
| * notifier chain (used by usbfs and possibly others). |
| */ |
| err = device_add(&udev->dev); |
| if (err) { |
| dev_err(&udev->dev, "can't device_add, error %d\n", err); |
| goto fail; |
| } |
| |
| (void) usb_create_ep_devs(&udev->dev, &udev->ep0, udev); |
| return err; |
| |
| fail: |
| usb_set_device_state(udev, USB_STATE_NOTATTACHED); |
| usb_stop_pm(udev); |
| return err; |
| } |
| |
| |
| /** |
| * usb_deauthorize_device - deauthorize a device (usbcore-internal) |
| * @usb_dev: USB device |
| * |
| * Move the USB device to a very basic state where interfaces are disabled |
| * and the device is in fact unconfigured and unusable. |
| * |
| * We share a lock (that we have) with device_del(), so we need to |
| * defer its call. |
| */ |
| int usb_deauthorize_device(struct usb_device *usb_dev) |
| { |
| unsigned cnt; |
| usb_lock_device(usb_dev); |
| if (usb_dev->authorized == 0) |
| goto out_unauthorized; |
| usb_dev->authorized = 0; |
| usb_set_configuration(usb_dev, -1); |
| usb_dev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| usb_dev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| usb_dev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL); |
| kfree(usb_dev->config); |
| usb_dev->config = NULL; |
| for (cnt = 0; cnt < usb_dev->descriptor.bNumConfigurations; cnt++) |
| kfree(usb_dev->rawdescriptors[cnt]); |
| usb_dev->descriptor.bNumConfigurations = 0; |
| kfree(usb_dev->rawdescriptors); |
| out_unauthorized: |
| usb_unlock_device(usb_dev); |
| return 0; |
| } |
| |
| |
| int usb_authorize_device(struct usb_device *usb_dev) |
| { |
| int result = 0, c; |
| usb_lock_device(usb_dev); |
| if (usb_dev->authorized == 1) |
| goto out_authorized; |
| kfree(usb_dev->product); |
| usb_dev->product = NULL; |
| kfree(usb_dev->manufacturer); |
| usb_dev->manufacturer = NULL; |
| kfree(usb_dev->serial); |
| usb_dev->serial = NULL; |
| result = usb_autoresume_device(usb_dev); |
| if (result < 0) { |
| dev_err(&usb_dev->dev, |
| "can't autoresume for authorization: %d\n", result); |
| goto error_autoresume; |
| } |
| result = usb_get_device_descriptor(usb_dev, sizeof(usb_dev->descriptor)); |
| if (result < 0) { |
| dev_err(&usb_dev->dev, "can't re-read device descriptor for " |
| "authorization: %d\n", result); |
| goto error_device_descriptor; |
| } |
| usb_dev->authorized = 1; |
| result = usb_configure_device(usb_dev); |
| if (result < 0) |
| goto error_configure; |
| /* Choose and set the configuration. This registers the interfaces |
| * with the driver core and lets interface drivers bind to them. |
| */ |
| c = usb_choose_configuration(usb_dev); |
| if (c >= 0) { |
| result = usb_set_configuration(usb_dev, c); |
| if (result) { |
| dev_err(&usb_dev->dev, |
| "can't set config #%d, error %d\n", c, result); |
| /* This need not be fatal. The user can try to |
| * set other configurations. */ |
| } |
| } |
| dev_info(&usb_dev->dev, "authorized to connect\n"); |
| error_configure: |
| error_device_descriptor: |
| error_autoresume: |
| out_authorized: |
| usb_unlock_device(usb_dev); // complements locktree |
| return result; |
| } |
| |
| |
| /* Returns 1 if @hub is a WUSB root hub, 0 otherwise */ |
| static unsigned hub_is_wusb(struct usb_hub *hub) |
| { |
| struct usb_hcd *hcd; |
| if (hub->hdev->parent != NULL) /* not a root hub? */ |
| return 0; |
| hcd = container_of(hub->hdev->bus, struct usb_hcd, self); |
| return hcd->wireless; |
| } |
| |
| |
| #define PORT_RESET_TRIES 5 |
| #define SET_ADDRESS_TRIES 2 |
| #define GET_DESCRIPTOR_TRIES 2 |
| #define SET_CONFIG_TRIES (2 * (use_both_schemes + 1)) |
| #define USE_NEW_SCHEME(i) ((i) / 2 == old_scheme_first) |
| |
| #define HUB_ROOT_RESET_TIME 50 /* times are in msec */ |
| #define HUB_SHORT_RESET_TIME 10 |
| #define HUB_LONG_RESET_TIME 200 |
| #define HUB_RESET_TIMEOUT 500 |
| |
| static int hub_port_wait_reset(struct usb_hub *hub, int port1, |
| struct usb_device *udev, unsigned int delay) |
| { |
| int delay_time, ret; |
| u16 portstatus; |
| u16 portchange; |
| |
| for (delay_time = 0; |
| delay_time < HUB_RESET_TIMEOUT; |
| delay_time += delay) { |
| /* wait to give the device a chance to reset */ |
| msleep(delay); |
| |
| /* read and decode port status */ |
| ret = hub_port_status(hub, port1, &portstatus, &portchange); |
| if (ret < 0) |
| return ret; |
| |
| /* Device went away? */ |
| if (!(portstatus & USB_PORT_STAT_CONNECTION)) |
| return -ENOTCONN; |
| |
| /* bomb out completely if the connection bounced */ |
| if ((portchange & USB_PORT_STAT_C_CONNECTION)) |
| return -ENOTCONN; |
| |
| /* if we`ve finished resetting, then break out of the loop */ |
| if (!(portstatus & USB_PORT_STAT_RESET) && |
| (portstatus & USB_PORT_STAT_ENABLE)) { |
| if (hub_is_wusb(hub)) |
| udev->speed = USB_SPEED_VARIABLE; |
| else if (portstatus & USB_PORT_STAT_HIGH_SPEED) |
| udev->speed = USB_SPEED_HIGH; |
| else if (portstatus & USB_PORT_STAT_LOW_SPEED) |
| udev->speed = USB_SPEED_LOW; |
| else |
| udev->speed = USB_SPEED_FULL; |
| return 0; |
| } |
| |
| /* switch to the long delay after two short delay failures */ |
| if (delay_time >= 2 * HUB_SHORT_RESET_TIME) |
| delay = HUB_LONG_RESET_TIME; |
| |
| dev_dbg (hub->intfdev, |
| "port %d not reset yet, waiting %dms\n", |
| port1, delay); |
| } |
| |
| return -EBUSY; |
| } |
| |
| static int hub_port_reset(struct usb_hub *hub, int port1, |
| struct usb_device *udev, unsigned int delay) |
| { |
| int i, status; |
| |
| /* Block EHCI CF initialization during the port reset. |
| * Some companion controllers don't like it when they mix. |
| */ |
| down_read(&ehci_cf_port_reset_rwsem); |
| |
| /* Reset the port */ |
| for (i = 0; i < PORT_RESET_TRIES; i++) { |
| status = set_port_feature(hub->hdev, |
| port1, USB_PORT_FEAT_RESET); |
| if (status) |
| dev_err(hub->intfdev, |
| "cannot reset port %d (err = %d)\n", |
| port1, status); |
| else { |
| status = hub_port_wait_reset(hub, port1, udev, delay); |
| if (status && status != -ENOTCONN) |
| dev_dbg(hub->intfdev, |
| "port_wait_reset: err = %d\n", |
| status); |
| } |
| |
| /* return on disconnect or reset */ |
| switch (status) { |
| case 0: |
| /* TRSTRCY = 10 ms; plus some extra */ |
| msleep(10 + 40); |
| update_address(udev, 0); |
| /* FALL THROUGH */ |
| case -ENOTCONN: |
| case -ENODEV: |
| clear_port_feature(hub->hdev, |
| port1, USB_PORT_FEAT_C_RESET); |
| /* FIXME need disconnect() for NOTATTACHED device */ |
| usb_set_device_state(udev, status |
| ? USB_STATE_NOTATTACHED |
| : USB_STATE_DEFAULT); |
| goto done; |
| } |
| |
| dev_dbg (hub->intfdev, |
| "port %d not enabled, trying reset again...\n", |
| port1); |
| delay = HUB_LONG_RESET_TIME; |
| } |
| |
| dev_err (hub->intfdev, |
| "Cannot enable port %i. Maybe the USB cable is bad?\n", |
| port1); |
| |
| done: |
| up_read(&ehci_cf_port_reset_rwsem); |
| return status; |
| } |
| |
| #ifdef CONFIG_PM |
| |
| #define MASK_BITS (USB_PORT_STAT_POWER | USB_PORT_STAT_CONNECTION | \ |
| USB_PORT_STAT_SUSPEND) |
| #define WANT_BITS (USB_PORT_STAT_POWER | USB_PORT_STAT_CONNECTION) |
| |
| /* Determine whether the device on a port is ready for a normal resume, |
| * is ready for a reset-resume, or should be disconnected. |
| */ |
| static int check_port_resume_type(struct usb_device *udev, |
| struct usb_hub *hub, int port1, |
| int status, unsigned portchange, unsigned portstatus) |
| { |
| /* Is the device still present? */ |
| if (status || (portstatus & MASK_BITS) != WANT_BITS) { |
| if (status >= 0) |
| status = -ENODEV; |
| } |
| |
| /* Can't do a normal resume if the port isn't enabled, |
| * so try a reset-resume instead. |
| */ |
| else if (!(portstatus & USB_PORT_STAT_ENABLE) && !udev->reset_resume) { |
| if (udev->persist_enabled) |
| udev->reset_resume = 1; |
| else |
| status = -ENODEV; |
| } |
| |
| if (status) { |
| dev_dbg(hub->intfdev, |
| "port %d status %04x.%04x after resume, %d\n", |
| port1, portchange, portstatus, status); |
| } else if (udev->reset_resume) { |
| |
| /* Late port handoff can set status-change bits */ |
| if (portchange & USB_PORT_STAT_C_CONNECTION) |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_CONNECTION); |
| if (portchange & USB_PORT_STAT_C_ENABLE) |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_ENABLE); |
| } |
| |
| return status; |
| } |
| |
| #ifdef CONFIG_USB_SUSPEND |
| |
| /* |
| * usb_port_suspend - suspend a usb device's upstream port |
| * @udev: device that's no longer in active use, not a root hub |
| * Context: must be able to sleep; device not locked; pm locks held |
| * |
| * Suspends a USB device that isn't in active use, conserving power. |
| * Devices may wake out of a suspend, if anything important happens, |
| * using the remote wakeup mechanism. They may also be taken out of |
| * suspend by the host, using usb_port_resume(). It's also routine |
| * to disconnect devices while they are suspended. |
| * |
| * This only affects the USB hardware for a device; its interfaces |
| * (and, for hubs, child devices) must already have been suspended. |
| * |
| * Selective port suspend reduces power; most suspended devices draw |
| * less than 500 uA. It's also used in OTG, along with remote wakeup. |
| * All devices below the suspended port are also suspended. |
| * |
| * Devices leave suspend state when the host wakes them up. Some devices |
| * also support "remote wakeup", where the device can activate the USB |
| * tree above them to deliver data, such as a keypress or packet. In |
| * some cases, this wakes the USB host. |
| * |
| * Suspending OTG devices may trigger HNP, if that's been enabled |
| * between a pair of dual-role devices. That will change roles, such |
| * as from A-Host to A-Peripheral or from B-Host back to B-Peripheral. |
| * |
| * Devices on USB hub ports have only one "suspend" state, corresponding |
| * to ACPI D2, "may cause the device to lose some context". |
| * State transitions include: |
| * |
| * - suspend, resume ... when the VBUS power link stays live |
| * - suspend, disconnect ... VBUS lost |
| * |
| * Once VBUS drop breaks the circuit, the port it's using has to go through |
| * normal re-enumeration procedures, starting with enabling VBUS power. |
| * Other than re-initializing the hub (plug/unplug, except for root hubs), |
| * Linux (2.6) currently has NO mechanisms to initiate that: no khubd |
| * timer, no SRP, no requests through sysfs. |
| * |
| * If CONFIG_USB_SUSPEND isn't enabled, devices only really suspend when |
| * the root hub for their bus goes into global suspend ... so we don't |
| * (falsely) update the device power state to say it suspended. |
| * |
| * Returns 0 on success, else negative errno. |
| */ |
| int usb_port_suspend(struct usb_device *udev, pm_message_t msg) |
| { |
| struct usb_hub *hub = hdev_to_hub(udev->parent); |
| int port1 = udev->portnum; |
| int status; |
| |
| // dev_dbg(hub->intfdev, "suspend port %d\n", port1); |
| |
| /* enable remote wakeup when appropriate; this lets the device |
| * wake up the upstream hub (including maybe the root hub). |
| * |
| * NOTE: OTG devices may issue remote wakeup (or SRP) even when |
| * we don't explicitly enable it here. |
| */ |
| if (udev->do_remote_wakeup) { |
| status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| USB_REQ_SET_FEATURE, USB_RECIP_DEVICE, |
| USB_DEVICE_REMOTE_WAKEUP, 0, |
| NULL, 0, |
| USB_CTRL_SET_TIMEOUT); |
| if (status) |
| dev_dbg(&udev->dev, "won't remote wakeup, status %d\n", |
| status); |
| } |
| |
| /* see 7.1.7.6 */ |
| status = set_port_feature(hub->hdev, port1, USB_PORT_FEAT_SUSPEND); |
| if (status) { |
| dev_dbg(hub->intfdev, "can't suspend port %d, status %d\n", |
| port1, status); |
| /* paranoia: "should not happen" */ |
| (void) usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| USB_REQ_CLEAR_FEATURE, USB_RECIP_DEVICE, |
| USB_DEVICE_REMOTE_WAKEUP, 0, |
| NULL, 0, |
| USB_CTRL_SET_TIMEOUT); |
| } else { |
| /* device has up to 10 msec to fully suspend */ |
| dev_dbg(&udev->dev, "usb %ssuspend\n", |
| (msg.event & PM_EVENT_AUTO ? "auto-" : "")); |
| usb_set_device_state(udev, USB_STATE_SUSPENDED); |
| msleep(10); |
| } |
| return status; |
| } |
| |
| /* |
| * If the USB "suspend" state is in use (rather than "global suspend"), |
| * many devices will be individually taken out of suspend state using |
| * special "resume" signaling. This routine kicks in shortly after |
| * hardware resume signaling is finished, either because of selective |
| * resume (by host) or remote wakeup (by device) ... now see what changed |
| * in the tree that's rooted at this device. |
| * |
| * If @udev->reset_resume is set then the device is reset before the |
| * status check is done. |
| */ |
| static int finish_port_resume(struct usb_device *udev) |
| { |
| int status = 0; |
| u16 devstatus; |
| |
| /* caller owns the udev device lock */ |
| dev_dbg(&udev->dev, "%s\n", |
| udev->reset_resume ? "finish reset-resume" : "finish resume"); |
| |
| /* usb ch9 identifies four variants of SUSPENDED, based on what |
| * state the device resumes to. Linux currently won't see the |
| * first two on the host side; they'd be inside hub_port_init() |
| * during many timeouts, but khubd can't suspend until later. |
| */ |
| usb_set_device_state(udev, udev->actconfig |
| ? USB_STATE_CONFIGURED |
| : USB_STATE_ADDRESS); |
| |
| /* 10.5.4.5 says not to reset a suspended port if the attached |
| * device is enabled for remote wakeup. Hence the reset |
| * operation is carried out here, after the port has been |
| * resumed. |
| */ |
| if (udev->reset_resume) |
| retry_reset_resume: |
| status = usb_reset_and_verify_device(udev); |
| |
| /* 10.5.4.5 says be sure devices in the tree are still there. |
| * For now let's assume the device didn't go crazy on resume, |
| * and device drivers will know about any resume quirks. |
| */ |
| if (status == 0) { |
| devstatus = 0; |
| status = usb_get_status(udev, USB_RECIP_DEVICE, 0, &devstatus); |
| if (status >= 0) |
| status = (status > 0 ? 0 : -ENODEV); |
| |
| /* If a normal resume failed, try doing a reset-resume */ |
| if (status && !udev->reset_resume && udev->persist_enabled) { |
| dev_dbg(&udev->dev, "retry with reset-resume\n"); |
| udev->reset_resume = 1; |
| goto retry_reset_resume; |
| } |
| } |
| |
| if (status) { |
| dev_dbg(&udev->dev, "gone after usb resume? status %d\n", |
| status); |
| } else if (udev->actconfig) { |
| le16_to_cpus(&devstatus); |
| if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) { |
| status = usb_control_msg(udev, |
| usb_sndctrlpipe(udev, 0), |
| USB_REQ_CLEAR_FEATURE, |
| USB_RECIP_DEVICE, |
| USB_DEVICE_REMOTE_WAKEUP, 0, |
| NULL, 0, |
| USB_CTRL_SET_TIMEOUT); |
| if (status) |
| dev_dbg(&udev->dev, |
| "disable remote wakeup, status %d\n", |
| status); |
| } |
| status = 0; |
| } |
| return status; |
| } |
| |
| /* |
| * usb_port_resume - re-activate a suspended usb device's upstream port |
| * @udev: device to re-activate, not a root hub |
| * Context: must be able to sleep; device not locked; pm locks held |
| * |
| * This will re-activate the suspended device, increasing power usage |
| * while letting drivers communicate again with its endpoints. |
| * USB resume explicitly guarantees that the power session between |
| * the host and the device is the same as it was when the device |
| * suspended. |
| * |
| * If @udev->reset_resume is set then this routine won't check that the |
| * port is still enabled. Furthermore, finish_port_resume() above will |
| * reset @udev. The end result is that a broken power session can be |
| * recovered and @udev will appear to persist across a loss of VBUS power. |
| * |
| * For example, if a host controller doesn't maintain VBUS suspend current |
| * during a system sleep or is reset when the system wakes up, all the USB |
| * power sessions below it will be broken. This is especially troublesome |
| * for mass-storage devices containing mounted filesystems, since the |
| * device will appear to have disconnected and all the memory mappings |
| * to it will be lost. Using the USB_PERSIST facility, the device can be |
| * made to appear as if it had not disconnected. |
| * |
| * This facility can be dangerous. Although usb_reset_and_verify_device() makes |
| * every effort to insure that the same device is present after the |
| * reset as before, it cannot provide a 100% guarantee. Furthermore it's |
| * quite possible for a device to remain unaltered but its media to be |
| * changed. If the user replaces a flash memory card while the system is |
| * asleep, he will have only himself to blame when the filesystem on the |
| * new card is corrupted and the system crashes. |
| * |
| * Returns 0 on success, else negative errno. |
| */ |
| int usb_port_resume(struct usb_device *udev, pm_message_t msg) |
| { |
| struct usb_hub *hub = hdev_to_hub(udev->parent); |
| int port1 = udev->portnum; |
| int status; |
| u16 portchange, portstatus; |
| |
| /* Skip the initial Clear-Suspend step for a remote wakeup */ |
| status = hub_port_status(hub, port1, &portstatus, &portchange); |
| if (status == 0 && !(portstatus & USB_PORT_STAT_SUSPEND)) |
| goto SuspendCleared; |
| |
| // dev_dbg(hub->intfdev, "resume port %d\n", port1); |
| |
| set_bit(port1, hub->busy_bits); |
| |
| /* see 7.1.7.7; affects power usage, but not budgeting */ |
| status = clear_port_feature(hub->hdev, |
| port1, USB_PORT_FEAT_SUSPEND); |
| if (status) { |
| dev_dbg(hub->intfdev, "can't resume port %d, status %d\n", |
| port1, status); |
| } else { |
| /* drive resume for at least 20 msec */ |
| dev_dbg(&udev->dev, "usb %sresume\n", |
| (msg.event & PM_EVENT_AUTO ? "auto-" : "")); |
| msleep(25); |
| |
| /* Virtual root hubs can trigger on GET_PORT_STATUS to |
| * stop resume signaling. Then finish the resume |
| * sequence. |
| */ |
| status = hub_port_status(hub, port1, &portstatus, &portchange); |
| |
| /* TRSMRCY = 10 msec */ |
| msleep(10); |
| } |
| |
| SuspendCleared: |
| if (status == 0) { |
| if (portchange & USB_PORT_STAT_C_SUSPEND) |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_SUSPEND); |
| } |
| |
| clear_bit(port1, hub->busy_bits); |
| |
| status = check_port_resume_type(udev, |
| hub, port1, status, portchange, portstatus); |
| if (status == 0) |
| status = finish_port_resume(udev); |
| if (status < 0) { |
| dev_dbg(&udev->dev, "can't resume, status %d\n", status); |
| hub_port_logical_disconnect(hub, port1); |
| } |
| return status; |
| } |
| |
| /* caller has locked udev */ |
| static int remote_wakeup(struct usb_device *udev) |
| { |
| int status = 0; |
| |
| if (udev->state == USB_STATE_SUSPENDED) { |
| dev_dbg(&udev->dev, "usb %sresume\n", "wakeup-"); |
| usb_mark_last_busy(udev); |
| status = usb_external_resume_device(udev, PMSG_REMOTE_RESUME); |
| } |
| return status; |
| } |
| |
| #else /* CONFIG_USB_SUSPEND */ |
| |
| /* When CONFIG_USB_SUSPEND isn't set, we never suspend or resume any ports. */ |
| |
| int usb_port_suspend(struct usb_device *udev, pm_message_t msg) |
| { |
| return 0; |
| } |
| |
| /* However we may need to do a reset-resume */ |
| |
| int usb_port_resume(struct usb_device *udev, pm_message_t msg) |
| { |
| struct usb_hub *hub = hdev_to_hub(udev->parent); |
| int port1 = udev->portnum; |
| int status; |
| u16 portchange, portstatus; |
| |
| status = hub_port_status(hub, port1, &portstatus, &portchange); |
| status = check_port_resume_type(udev, |
| hub, port1, status, portchange, portstatus); |
| |
| if (status) { |
| dev_dbg(&udev->dev, "can't resume, status %d\n", status); |
| hub_port_logical_disconnect(hub, port1); |
| } else if (udev->reset_resume) { |
| dev_dbg(&udev->dev, "reset-resume\n"); |
| status = usb_reset_and_verify_device(udev); |
| } |
| return status; |
| } |
| |
| static inline int remote_wakeup(struct usb_device *udev) |
| { |
| return 0; |
| } |
| |
| #endif |
| |
| static int hub_suspend(struct usb_interface *intf, pm_message_t msg) |
| { |
| struct usb_hub *hub = usb_get_intfdata (intf); |
| struct usb_device *hdev = hub->hdev; |
| unsigned port1; |
| |
| /* fail if children aren't already suspended */ |
| for (port1 = 1; port1 <= hdev->maxchild; port1++) { |
| struct usb_device *udev; |
| |
| udev = hdev->children [port1-1]; |
| if (udev && udev->can_submit) { |
| if (!(msg.event & PM_EVENT_AUTO)) |
| dev_dbg(&intf->dev, "port %d nyet suspended\n", |
| port1); |
| return -EBUSY; |
| } |
| } |
| |
| dev_dbg(&intf->dev, "%s\n", __func__); |
| |
| /* stop khubd and related activity */ |
| hub_quiesce(hub, HUB_SUSPEND); |
| return 0; |
| } |
| |
| static int hub_resume(struct usb_interface *intf) |
| { |
| struct usb_hub *hub = usb_get_intfdata(intf); |
| |
| dev_dbg(&intf->dev, "%s\n", __func__); |
| hub_activate(hub, HUB_RESUME); |
| return 0; |
| } |
| |
| static int hub_reset_resume(struct usb_interface *intf) |
| { |
| struct usb_hub *hub = usb_get_intfdata(intf); |
| |
| dev_dbg(&intf->dev, "%s\n", __func__); |
| hub_activate(hub, HUB_RESET_RESUME); |
| return 0; |
| } |
| |
| /** |
| * usb_root_hub_lost_power - called by HCD if the root hub lost Vbus power |
| * @rhdev: struct usb_device for the root hub |
| * |
| * The USB host controller driver calls this function when its root hub |
| * is resumed and Vbus power has been interrupted or the controller |
| * has been reset. The routine marks @rhdev as having lost power. |
| * When the hub driver is resumed it will take notice and carry out |
| * power-session recovery for all the "USB-PERSIST"-enabled child devices; |
| * the others will be disconnected. |
| */ |
| void usb_root_hub_lost_power(struct usb_device *rhdev) |
| { |
| dev_warn(&rhdev->dev, "root hub lost power or was reset\n"); |
| rhdev->reset_resume = 1; |
| } |
| EXPORT_SYMBOL_GPL(usb_root_hub_lost_power); |
| |
| #else /* CONFIG_PM */ |
| |
| static inline int remote_wakeup(struct usb_device *udev) |
| { |
| return 0; |
| } |
| |
| #define hub_suspend NULL |
| #define hub_resume NULL |
| #define hub_reset_resume NULL |
| #endif |
| |
| |
| /* USB 2.0 spec, 7.1.7.3 / fig 7-29: |
| * |
| * Between connect detection and reset signaling there must be a delay |
| * of 100ms at least for debounce and power-settling. The corresponding |
| * timer shall restart whenever the downstream port detects a disconnect. |
| * |
| * Apparently there are some bluetooth and irda-dongles and a number of |
| * low-speed devices for which this debounce period may last over a second. |
| * Not covered by the spec - but easy to deal with. |
| * |
| * This implementation uses a 1500ms total debounce timeout; if the |
| * connection isn't stable by then it returns -ETIMEDOUT. It checks |
| * every 25ms for transient disconnects. When the port status has been |
| * unchanged for 100ms it returns the port status. |
| */ |
| static int hub_port_debounce(struct usb_hub *hub, int port1) |
| { |
| int ret; |
| int total_time, stable_time = 0; |
| u16 portchange, portstatus; |
| unsigned connection = 0xffff; |
| |
| for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) { |
| ret = hub_port_status(hub, port1, &portstatus, &portchange); |
| if (ret < 0) |
| return ret; |
| |
| if (!(portchange & USB_PORT_STAT_C_CONNECTION) && |
| (portstatus & USB_PORT_STAT_CONNECTION) == connection) { |
| stable_time += HUB_DEBOUNCE_STEP; |
| if (stable_time >= HUB_DEBOUNCE_STABLE) |
| break; |
| } else { |
| stable_time = 0; |
| connection = portstatus & USB_PORT_STAT_CONNECTION; |
| } |
| |
| if (portchange & USB_PORT_STAT_C_CONNECTION) { |
| clear_port_feature(hub->hdev, port1, |
| USB_PORT_FEAT_C_CONNECTION); |
| } |
| |
| if (total_time >= HUB_DEBOUNCE_TIMEOUT) |
| break; |
| msleep(HUB_DEBOUNCE_STEP); |
| } |
| |
| dev_dbg (hub->intfdev, |
| "debounce: port %d: total %dms stable %dms status 0x%x\n", |
| port1, total_time, stable_time, portstatus); |
| |
| if (stable_time < HUB_DEBOUNCE_STABLE) |
| return -ETIMEDOUT; |
| return portstatus; |
| } |
| |
| void usb_ep0_reinit(struct usb_device *udev) |
| { |
| usb_disable_endpoint(udev, 0 + USB_DIR_IN, true); |
| usb_disable_endpoint(udev, 0 + USB_DIR_OUT, true); |
| usb_enable_endpoint(udev, &udev->ep0, true); |
| } |
| EXPORT_SYMBOL_GPL(usb_ep0_reinit); |
| |
| #define usb_sndaddr0pipe() (PIPE_CONTROL << 30) |
| #define usb_rcvaddr0pipe() ((PIPE_CONTROL << 30) | USB_DIR_IN) |
| |
| static int hub_set_address(struct usb_device *udev, int devnum) |
| { |
| int retval; |
| struct usb_hcd *hcd = bus_to_hcd(udev->bus); |
| |
| /* |
| * The host controller will choose the device address, |
| * instead of the core having chosen it earlier |
| */ |
| if (!hcd->driver->address_device && devnum <= 1) |
| return -EINVAL; |
| if (udev->state == USB_STATE_ADDRESS) |
| return 0; |
| if (udev->state != USB_STATE_DEFAULT) |
| return -EINVAL; |
| if (hcd->driver->address_device) { |
| retval = hcd->driver->address_device(hcd, udev); |
| } else { |
| retval = usb_control_msg(udev, usb_sndaddr0pipe(), |
| USB_REQ_SET_ADDRESS, 0, devnum, 0, |
| NULL, 0, USB_CTRL_SET_TIMEOUT); |
| if (retval == 0) |
| update_address(udev, devnum); |
| } |
| if (retval == 0) { |
| /* Device now using proper address. */ |
| usb_set_device_state(udev, USB_STATE_ADDRESS); |
| usb_ep0_reinit(udev); |
| } |
| return retval; |
| } |
| |
| /* Reset device, (re)assign address, get device descriptor. |
| * Device connection must be stable, no more debouncing needed. |
| * Returns device in USB_STATE_ADDRESS, except on error. |
| * |
| * If this is called for an already-existing device (as part of |
| * usb_reset_and_verify_device), the caller must own the device lock. For a |
| * newly detected device that is not accessible through any global |
| * pointers, it's not necessary to lock the device. |
| */ |
| static int |
| hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, |
| int retry_counter) |
| { |
| static DEFINE_MUTEX(usb_address0_mutex); |
| |
| struct usb_device *hdev = hub->hdev; |
| struct usb_hcd *hcd = bus_to_hcd(hdev->bus); |
| int i, j, retval; |
| unsigned delay = HUB_SHORT_RESET_TIME; |
| enum usb_device_speed oldspeed = udev->speed; |
| char *speed, *type; |
| int devnum = udev->devnum; |
| |
| /* root hub ports have a slightly longer reset period |
| * (from USB 2.0 spec, section 7.1.7.5) |
| */ |
| if (!hdev->parent) { |
| delay = HUB_ROOT_RESET_TIME; |
| if (port1 == hdev->bus->otg_port) |
| hdev->bus->b_hnp_enable = 0; |
| } |
| |
| /* Some low speed devices have problems with the quick delay, so */ |
| /* be a bit pessimistic with those devices. RHbug #23670 */ |
| if (oldspeed == USB_SPEED_LOW) |
| delay = HUB_LONG_RESET_TIME; |
| |
| mutex_lock(&usb_address0_mutex); |
| |
| if ((hcd->driver->flags & HCD_USB3) && udev->config) { |
| /* FIXME this will need special handling by the xHCI driver. */ |
| dev_dbg(&udev->dev, |
| "xHCI reset of configured device " |
| "not supported yet.\n"); |
| retval = -EINVAL; |
| goto fail; |
| } else if (!udev->config && oldspeed == USB_SPEED_SUPER) { |
| /* Don't reset USB 3.0 devices during an initial setup */ |
| usb_set_device_state(udev, USB_STATE_DEFAULT); |
| } else { |
| /* Reset the device; full speed may morph to high speed */ |
| /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */ |
| retval = hub_port_reset(hub, port1, udev, delay); |
| if (retval < 0) /* error or disconnect */ |
| goto fail; |
| /* success, speed is known */ |
| } |
| retval = -ENODEV; |
| |
| if (oldspeed != USB_SPEED_UNKNOWN && oldspeed != udev->speed) { |
| dev_dbg(&udev->dev, "device reset changed speed!\n"); |
| goto fail; |
| } |
| oldspeed = udev->speed; |
| |
| /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ... |
| * it's fixed size except for full speed devices. |
| * For Wireless USB devices, ep0 max packet is always 512 (tho |
| * reported as 0xff in the device descriptor). WUSB1.0[4.8.1]. |
| */ |
| switch (udev->speed) { |
| case USB_SPEED_SUPER: |
| case USB_SPEED_VARIABLE: /* fixed at 512 */ |
| udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512); |
| break; |
| case USB_SPEED_HIGH: /* fixed at 64 */ |
| udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); |
| break; |
| case USB_SPEED_FULL: /* 8, 16, 32, or 64 */ |
| /* to determine the ep0 maxpacket size, try to read |
| * the device descriptor to get bMaxPacketSize0 and |
| * then correct our initial guess. |
| */ |
| udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64); |
| break; |
| case USB_SPEED_LOW: /* fixed at 8 */ |
| udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8); |
| break; |
| default: |
| goto fail; |
| } |
| |
| type = ""; |
| switch (udev->speed) { |
| case USB_SPEED_LOW: speed = "low"; break; |
| case USB_SPEED_FULL: speed = "full"; break; |
| case USB_SPEED_HIGH: speed = "high"; break; |
| case USB_SPEED_SUPER: |
| speed = "super"; |
| break; |
| case USB_SPEED_VARIABLE: |
| speed = "variable"; |
| type = "Wireless "; |
| break; |
| default: speed = "?"; break; |
| } |
| if (udev->speed != USB_SPEED_SUPER) |
| dev_info(&udev->dev, |
| "%s %s speed %sUSB device using %s and address %d\n", |
| (udev->config) ? "reset" : "new", speed, type, |
| udev->bus->controller->driver->name, devnum); |
| |
| /* Set up TT records, if needed */ |
| if (hdev->tt) { |
| udev->tt = hdev->tt; |
| udev->ttport = hdev->ttport; |
| } else if (udev->speed != USB_SPEED_HIGH |
| && hdev->speed == USB_SPEED_HIGH) { |
| udev->tt = &hub->tt; |
| udev->ttport = port1; |
| } |
| |
| /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way? |
| * Because device hardware and firmware is sometimes buggy in |
| * this area, and this is how Linux has done it for ages. |
| * Change it cautiously. |
| * |
| * NOTE: If USE_NEW_SCHEME() is true we will start by issuing |
| * a 64-byte GET_DESCRIPTOR request. This is what Windows does, |
| * so it may help with some non-standards-compliant devices. |
| * Otherwise we start with SET_ADDRESS and then try to read the |
| * first 8 bytes of the device descriptor to get the ep0 maxpacket |
| * value. |
| */ |
| for (i = 0; i < GET_DESCRIPTOR_TRIES; (++i, msleep(100))) { |
| /* |
| * An xHCI controller cannot send any packets to a device until |
| * a set address command successfully completes. |
| */ |
| if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3)) { |
| struct usb_device_descriptor *buf; |
| int r = 0; |
| |
| #define GET_DESCRIPTOR_BUFSIZE 64 |
| buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO); |
| if (!buf) { |
| retval = -ENOMEM; |
| continue; |
| } |
| |
| /* Retry on all errors; some devices are flakey. |
| * 255 is for WUSB devices, we actually need to use |
| * 512 (WUSB1.0[4.8.1]). |
| */ |
| for (j = 0; j < 3; ++j) { |
| buf->bMaxPacketSize0 = 0; |
| r = usb_control_msg(udev, usb_rcvaddr0pipe(), |
| USB_REQ_GET_DESCRIPTOR, USB_DIR_IN, |
| USB_DT_DEVICE << 8, 0, |
| buf, GET_DESCRIPTOR_BUFSIZE, |
| initial_descriptor_timeout); |
| switch (buf->bMaxPacketSize0) { |
| case 8: case 16: case 32: case 64: case 255: |
| if (buf->bDescriptorType == |
| USB_DT_DEVICE) { |
| r = 0; |
| break; |
| } |
| /* FALL THROUGH */ |
| default: |
| if (r == 0) |
| r = -EPROTO; |
| break; |
| } |
| if (r == 0) |
| break; |
| } |
| udev->descriptor.bMaxPacketSize0 = |
| buf->bMaxPacketSize0; |
| kfree(buf); |
| |
| retval = hub_port_reset(hub, port1, udev, delay); |
| if (retval < 0) /* error or disconnect */ |
| goto fail; |
| if (oldspeed != udev->speed) { |
| dev_dbg(&udev->dev, |
| "device reset changed speed!\n"); |
| retval = -ENODEV; |
| goto fail; |
| } |
| if (r) { |
| dev_err(&udev->dev, |
| "device descriptor read/64, error %d\n", |
| r); |
| retval = -EMSGSIZE; |
| continue; |
| } |
| #undef GET_DESCRIPTOR_BUFSIZE |
| } |
| |
| /* |
| * If device is WUSB, we already assigned an |
| * unauthorized address in the Connect Ack sequence; |
| * authorization will assign the final address. |
| */ |
| if (udev->wusb == 0) { |
| for (j = 0; j < SET_ADDRESS_TRIES; ++j) { |
| retval = hub_set_address(udev, devnum); |
| if (retval >= 0) |
| break; |
| msleep(200); |
| } |
| if (retval < 0) { |
| dev_err(&udev->dev, |
| "device not accepting address %d, error %d\n", |
| devnum, retval); |
| goto fail; |
| } |
| if (udev->speed == USB_SPEED_SUPER) { |
| devnum = udev->devnum; |
| dev_info(&udev->dev, |
| "%s SuperSpeed USB device using %s and address %d\n", |
| (udev->config) ? "reset" : "new", |
| udev->bus->controller->driver->name, devnum); |
| } |
| |
| /* cope with hardware quirkiness: |
| * - let SET_ADDRESS settle, some device hardware wants it |
| * - read ep0 maxpacket even for high and low speed, |
| */ |
| msleep(10); |
| if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3)) |
| break; |
| } |
| |
| retval = usb_get_device_descriptor(udev, 8); |
| if (retval < 8) { |
| dev_err(&udev->dev, |
| "device descriptor read/8, error %d\n", |
| retval); |
| if (retval >= 0) |
| retval = -EMSGSIZE; |
| } else { |
| retval = 0; |
| break; |
| } |
| } |
| if (retval) |
| goto fail; |
| |
| if (udev->descriptor.bMaxPacketSize0 == 0xff || |
| udev->speed == USB_SPEED_SUPER) |
| i = 512; |
| else |
| i = udev->descriptor.bMaxPacketSize0; |
| if (le16_to_cpu(udev->ep0.desc.wMaxPacketSize) != i) { |
| if (udev->speed != USB_SPEED_FULL || |
| !(i == 8 || i == 16 || i == 32 || i == 64)) { |
| dev_err(&udev->dev, "ep0 maxpacket = %d\n", i); |
| retval = -EMSGSIZE; |
| goto fail; |
| } |
| dev_dbg(&udev->dev, "ep0 maxpacket = %d\n", i); |
| udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i); |
| usb_ep0_reinit(udev); |
| } |
| |
| retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE); |
| if (retval < (signed)sizeof(udev->descriptor)) { |
| dev_err(&udev->dev, "device descriptor read/all, error %d\n", |
| retval); |
| if (retval >= 0) |
| retval = -ENOMSG; |
| goto fail; |
| } |
| |
| retval = 0; |
| |
| fail: |
| if (retval) { |
| hub_port_disable(hub, port1, 0); |
| update_address(udev, devnum); /* for disconnect processing */ |
| } |
| mutex_unlock(&usb_address0_mutex); |
| return retval; |
| } |
| |
| static void |
| check_highspeed (struct usb_hub *hub, struct usb_device *udev, int port1) |
| { |
| struct usb_qualifier_descriptor *qual; |
| int status; |
| |
| qual = kmalloc (sizeof *qual, GFP_KERNEL); |
| if (qual == NULL) |
| return; |
| |
| status = usb_get_descriptor (udev, USB_DT_DEVICE_QUALIFIER, 0, |
| qual, sizeof *qual); |
| if (status == sizeof *qual) { |
| dev_info(&udev->dev, "not running at top speed; " |
| "connect to a high speed hub\n"); |
| /* hub LEDs are probably harder to miss than syslog */ |
| if (hub->has_indicators) { |
| hub->indicator[port1-1] = INDICATOR_GREEN_BLINK; |
| schedule_delayed_work (&hub->leds, 0); |
| } |
| } |
| kfree(qual); |
| } |
| |
| static unsigned |
| hub_power_remaining (struct usb_hub *hub) |
| { |
| struct usb_device *hdev = hub->hdev; |
| int remaining; |
| int port1; |
| |
| if (!hub->limited_power) |
| return 0; |
| |
| remaining = hdev->bus_mA - hub->descriptor->bHubContrCurrent; |
| for (port1 = 1; port1 <= hdev->maxchild; ++port1) { |
| struct usb_device *udev = hdev->children[port1 - 1]; |
| int delta; |
| |
| if (!udev) |
| continue; |
| |
| /* Unconfigured devices may not use more than 100mA, |
| * or 8mA for OTG ports */ |
| if (udev->actconfig) |
| delta = udev->actconfig->desc.bMaxPower * 2; |
| else if (port1 != udev->bus->otg_port || hdev->parent) |
| delta = 100; |
| else |
| delta = 8; |
| if (delta > hub->mA_per_port) |
| dev_warn(&udev->dev, |
| "%dmA is over %umA budget for port %d!\n", |
| delta, hub->mA_per_port, port1); |
| remaining -= delta; |
| } |
| if (remaining < 0) { |
| dev_warn(hub->intfdev, "%dmA over power budget!\n", |
| - remaining); |
| remaining = 0; |
| } |
| return remaining; |
| } |
| |
| /* Handle physical or logical connection change events. |
| * This routine is called when: |
| * a port connection-change occurs; |
| * a port enable-change occurs (often caused by EMI); |
| * usb_reset_and_verify_device() encounters changed descriptors (as from |
| * a firmware download) |
| * caller already locked the hub |
| */ |
| static void hub_port_connect_change(struct usb_hub *hub, int port1, |
| u16 portstatus, u16 portchange) |
| { |
| struct usb_device *hdev = hub->hdev; |
| struct device *hub_dev = hub->intfdev; |
| struct usb_hcd *hcd = bus_to_hcd(hdev->bus); |
| unsigned wHubCharacteristics = |
| le16_to_cpu(hub->descriptor->wHubCharacteristics); |
| struct usb_device *udev; |
| int status, i; |
| |
| dev_dbg (hub_dev, |
| "port %d, status %04x, change %04x, %s\n", |
| port1, portstatus, portchange, portspeed (portstatus)); |
| |
| if (hub->has_indicators) { |
| set_port_led(hub, port1, HUB_LED_AUTO); |
| hub->indicator[port1-1] = INDICATOR_AUTO; |
| } |
| |
| #ifdef CONFIG_USB_OTG |
| /* during HNP, don't repeat the debounce */ |
| if (hdev->bus->is_b_host) |
| portchange &= ~(USB_PORT_STAT_C_CONNECTION | |
| USB_PORT_STAT_C_ENABLE); |
| #endif |
| |
| /* Try to resuscitate an existing device */ |
| udev = hdev->children[port1-1]; |
| if ((portstatus & USB_PORT_STAT_CONNECTION) && udev && |
| udev->state != USB_STATE_NOTATTACHED) { |
| usb_lock_device(udev); |
| if (portstatus & USB_PORT_STAT_ENABLE) { |
| status = 0; /* Nothing to do */ |
| |
| #ifdef CONFIG_USB_SUSPEND |
| } else if (udev->state == USB_STATE_SUSPENDED && |
| udev->persist_enabled) { |
| /* For a suspended device, treat this as a |
| * remote wakeup event. |
| */ |
| status = remote_wakeup(udev); |
| #endif |
| |
| } else { |
| status = -ENODEV; /* Don't resuscitate */ |
| } |
| usb_unlock_device(udev); |
| |
| if (status == 0) { |
| clear_bit(port1, hub->change_bits); |
| return; |
| } |
| } |
| |
| /* Disconnect any existing devices under this port */ |
| if (udev) |
| usb_disconnect(&hdev->children[port1-1]); |
| clear_bit(port1, hub->change_bits); |
| |
| if (portchange & (USB_PORT_STAT_C_CONNECTION | |
| USB_PORT_STAT_C_ENABLE)) { |
| status = hub_port_debounce(hub, port1); |
| if (status < 0) { |
| if (printk_ratelimit()) |
| dev_err(hub_dev, "connect-debounce failed, " |
| "port %d disabled\n", port1); |
| portstatus &= ~USB_PORT_STAT_CONNECTION; |
| } else { |
| portstatus = status; |
| } |
| } |
| |
| /* Return now if debouncing failed or nothing is connected */ |
| if (!(portstatus & USB_PORT_STAT_CONNECTION)) { |
| |
| /* maybe switch power back on (e.g. root hub was reset) */ |
| if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2 |
| && !(portstatus & (1 << USB_PORT_FEAT_POWER))) |
| set_port_feature(hdev, port1, USB_PORT_FEAT_POWER); |
| |
| if (portstatus & USB_PORT_STAT_ENABLE) |
| goto done; |
| return; |
| } |
| |
| for (i = 0; i < SET_CONFIG_TRIES; i++) { |
| |
| /* reallocate for each attempt, since references |
| * to the previous one can escape in various ways |
| */ |
| udev = usb_alloc_dev(hdev, hdev->bus, port1); |
| if (!udev) { |
| dev_err (hub_dev, |
| "couldn't allocate port %d usb_device\n", |
| port1); |
| goto done; |
| } |
| |
| usb_set_device_state(udev, USB_STATE_POWERED); |
| udev->bus_mA = hub->mA_per_port; |
| udev->level = hdev->level + 1; |
| udev->wusb = hub_is_wusb(hub); |
| |
| /* |
| * USB 3.0 devices are reset automatically before the connect |
| * port status change appears, and the root hub port status |
| * shows the correct speed. We also get port change |
| * notifications for USB 3.0 devices from the USB 3.0 portion of |
| * an external USB 3.0 hub, but this isn't handled correctly yet |
| * FIXME. |
| */ |
| |
| if (!(hcd->driver->flags & HCD_USB3)) |
| udev->speed = USB_SPEED_UNKNOWN; |
| else if ((hdev->parent == NULL) && |
| (portstatus & (1 << USB_PORT_FEAT_SUPERSPEED))) |
| udev->speed = USB_SPEED_SUPER; |
| else |
| udev->speed = USB_SPEED_UNKNOWN; |
| |
| /* |
| * xHCI needs to issue an address device command later |
| * in the hub_port_init sequence for SS/HS/FS/LS devices. |
| */ |
| if (!(hcd->driver->flags & HCD_USB3)) { |
| /* set the address */ |
| choose_address(udev); |
| if (udev->devnum <= 0) { |
| status = -ENOTCONN; /* Don't retry */ |
| goto loop; |
| } |
| } |
| |
| /* reset (non-USB 3.0 devices) and get descriptor */ |
| status = hub_port_init(hub, udev, port1, i); |
| if (status < 0) |
| goto loop; |
| |
| /* consecutive bus-powered hubs aren't reliable; they can |
| * violate the voltage drop budget. if the new child has |
| * a "powered" LED, users should notice we didn't enable it |
| * (without reading syslog), even without per-port LEDs |
| * on the parent. |
| */ |
| if (udev->descriptor.bDeviceClass == USB_CLASS_HUB |
| && udev->bus_mA <= 100) { |
| u16 devstat; |
| |
| status = usb_get_status(udev, USB_RECIP_DEVICE, 0, |
| &devstat); |
| if (status < 2) { |
| dev_dbg(&udev->dev, "get status %d ?\n", status); |
| goto loop_disable; |
| } |
| le16_to_cpus(&devstat); |
| if ((devstat & (1 << USB_DEVICE_SELF_POWERED)) == 0) { |
| dev_err(&udev->dev, |
| "can't connect bus-powered hub " |
| "to this port\n"); |
| if (hub->has_indicators) { |
| hub->indicator[port1-1] = |
| INDICATOR_AMBER_BLINK; |
| schedule_delayed_work (&hub->leds, 0); |
| } |
| status = -ENOTCONN; /* Don't retry */ |
| goto loop_disable; |
| } |
| } |
| |
| /* check for devices running slower than they could */ |
| if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200 |
| && udev->speed == USB_SPEED_FULL |
| && highspeed_hubs != 0) |
| check_highspeed (hub, udev, port1); |
| |
| /* Store the parent's children[] pointer. At this point |
| * udev becomes globally accessible, although presumably |
| * no one will look at it until hdev is unlocked. |
| */ |
| status = 0; |
| |
| /* We mustn't add new devices if the parent hub has |
| * been disconnected; we would race with the |
| * recursively_mark_NOTATTACHED() routine. |
| */ |
| spin_lock_irq(&device_state_lock); |
| if (hdev->state == USB_STATE_NOTATTACHED) |
| status = -ENOTCONN; |
| else |
| hdev->children[port1-1] = udev; |
| spin_unlock_irq(&device_state_lock); |
| |
| /* Run it through the hoops (find a driver, etc) */ |
| if (!status) { |
| status = usb_new_device(udev); |
| if (status) { |
| spin_lock_irq(&device_state_lock); |
| hdev->children[port1-1] = NULL; |
| spin_unlock_irq(&device_state_lock); |
| } |
| } |
| |
| if (status) |
| goto loop_disable; |
| |
| status = hub_power_remaining(hub); |
| if (status) |
| dev_dbg(hub_dev, "%dmA power budget left\n", status); |
| |
| return; |
| |
| loop_disable: |
| hub_port_disable(hub, port1, 1); |
| loop: |
| usb_ep0_reinit(udev); |
| release_address(udev); |
| usb_put_dev(udev); |
| if ((status == -ENOTCONN) || (status == -ENOTSUPP)) |
| break; |
| } |
| if (hub->hdev->parent || |
| !hcd->driver->port_handed_over || |
| !(hcd->driver->port_handed_over)(hcd, port1)) |
| dev_err(hub_dev, "unable to enumerate USB device on port %d\n", |
| port1); |
| |
| done: |
| hub_port_disable(hub, port1, 1); |
| if (hcd->driver->relinquish_port && !hub->hdev->parent) |
| hcd->driver->relinquish_port(hcd, port1); |
| } |
| |
| static void hub_events(void) |
| { |
| struct list_head *tmp; |
| struct usb_device *hdev; |
| struct usb_interface *intf; |
| struct usb_hub *hub; |
| struct device *hub_dev; |
| u16 hubstatus; |
| u16 hubchange; |
| u16 portstatus; |
| u16 portchange; |
| int i, ret; |
| int connect_change; |
| |
| /* |
| * We restart the list every time to avoid a deadlock with |
| * deleting hubs downstream from this one. This should be |
| * safe since we delete the hub from the event list. |
| * Not the most efficient, but avoids deadlocks. |
| */ |
| while (1) { |
| |
| /* Grab the first entry at the beginning of the list */ |
| spin_lock_irq(&hub_event_lock); |
| if (list_empty(&hub_event_list)) { |
| spin_unlock_irq(&hub_event_lock); |
| break; |
| } |
| |
| tmp = hub_event_list.next; |
| list_del_init(tmp); |
| |
| hub = list_entry(tmp, struct usb_hub, event_list); |
| kref_get(&hub->kref); |
| spin_unlock_irq(&hub_event_lock); |
| |
| hdev = hub->hdev; |
| hub_dev = hub->intfdev; |
| intf = to_usb_interface(hub_dev); |
| dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x\n", |
| hdev->state, hub->descriptor |
| ? hub->descriptor->bNbrPorts |
| : 0, |
| /* NOTE: expects max 15 ports... */ |
| (u16) hub->change_bits[0], |
| (u16) hub->event_bits[0]); |
| |
| /* Lock the device, then check to see if we were |
| * disconnected while waiting for the lock to succeed. */ |
| usb_lock_device(hdev); |
| if (unlikely(hub->disconnected)) |
| goto loop; |
| |
| /* If the hub has died, clean up after it */ |
| if (hdev->state == USB_STATE_NOTATTACHED) { |
| hub->error = -ENODEV; |
| hub_quiesce(hub, HUB_DISCONNECT); |
| goto loop; |
| } |
| |
| /* Autoresume */ |
| ret = usb_autopm_get_interface(intf); |
| if (ret) { |
| dev_dbg(hub_dev, "Can't autoresume: %d\n", ret); |
| goto loop; |
| } |
| |
| /* If this is an inactive hub, do nothing */ |
| if (hub->quiescing) |
| goto loop_autopm; |
| |
| if (hub->error) { |
| dev_dbg (hub_dev, "resetting for error %d\n", |
| hub->error); |
| |
| ret = usb_reset_device(hdev); |
| if (ret) { |
| dev_dbg (hub_dev, |
| "error resetting hub: %d\n", ret); |
| goto loop_autopm; |
| } |
| |
| hub->nerrors = 0; |
| hub->error = 0; |
| } |
| |
| /* deal with port status changes */ |
| for (i = 1; i <= hub->descriptor->bNbrPorts; i++) { |
| if (test_bit(i, hub->busy_bits)) |
| continue; |
| connect_change = test_bit(i, hub->change_bits); |
| if (!test_and_clear_bit(i, hub->event_bits) && |
| !connect_change) |
| continue; |
| |
| ret = hub_port_status(hub, i, |
| &portstatus, &portchange); |
| if (ret < 0) |
| continue; |
| |
| if (portchange & USB_PORT_STAT_C_CONNECTION) { |
| clear_port_feature(hdev, i, |
| USB_PORT_FEAT_C_CONNECTION); |
| connect_change = 1; |
| } |
| |
| if (portchange & USB_PORT_STAT_C_ENABLE) { |
| if (!connect_change) |
| dev_dbg (hub_dev, |
| "port %d enable change, " |
| "status %08x\n", |
| i, portstatus); |
| clear_port_feature(hdev, i, |
| USB_PORT_FEAT_C_ENABLE); |
| |
| /* |
| * EM interference sometimes causes badly |
| * shielded USB devices to be shutdown by |
| * the hub, this hack enables them again. |
| * Works at least with mouse driver. |
| */ |
| if (!(portstatus & USB_PORT_STAT_ENABLE) |
| && !connect_change |
| && hdev->children[i-1]) { |
| dev_err (hub_dev, |
| "port %i " |
| "disabled by hub (EMI?), " |
| "re-enabling...\n", |
| i); |
| connect_change = 1; |
| } |
| } |
| |
| if (portchange & USB_PORT_STAT_C_SUSPEND) { |
| struct usb_device *udev; |
| |
| clear_port_feature(hdev, i, |
| USB_PORT_FEAT_C_SUSPEND); |
| udev = hdev->children[i-1]; |
| if (udev) { |
| usb_lock_device(udev); |
| ret = remote_wakeup(hdev-> |
| children[i-1]); |
| usb_unlock_device(udev); |
| if (ret < 0) |
| connect_change = 1; |
| } else { |
| ret = -ENODEV; |
| hub_port_disable(hub, i, 1); |
| } |
| dev_dbg (hub_dev, |
| "resume on port %d, status %d\n", |
| i, ret); |
| } |
| |
| if (portchange & USB_PORT_STAT_C_OVERCURRENT) { |
| dev_err (hub_dev, |
| "over-current change on port %d\n", |
| i); |
| clear_port_feature(hdev, i, |
| USB_PORT_FEAT_C_OVER_CURRENT); |
| hub_power_on(hub, true); |
| } |
| |
| if (portchange & USB_PORT_STAT_C_RESET) { |
| dev_dbg (hub_dev, |
| "reset change on port %d\n", |
| i); |
| clear_port_feature(hdev, i, |
| USB_PORT_FEAT_C_RESET); |
| } |
| |
| if (connect_change) |
| hub_port_connect_change(hub, i, |
| portstatus, portchange); |
| } /* end for i */ |
| |
| /* deal with hub status changes */ |
| if (test_and_clear_bit(0, hub->event_bits) == 0) |
| ; /* do nothing */ |
| else if (hub_hub_status(hub, &hubstatus, &hubchange) < 0) |
| dev_err (hub_dev, "get_hub_status failed\n"); |
| else { |
| if (hubchange & HUB_CHANGE_LOCAL_POWER) { |
| dev_dbg (hub_dev, "power change\n"); |
| clear_hub_feature(hdev, C_HUB_LOCAL_POWER); |
| if (hubstatus & HUB_STATUS_LOCAL_POWER) |
| /* FIXME: Is this always true? */ |
| hub->limited_power = 1; |
| else |
| hub->limited_power = 0; |
| } |
| if (hubchange & HUB_CHANGE_OVERCURRENT) { |
| dev_dbg (hub_dev, "overcurrent change\n"); |
| msleep(500); /* Cool down */ |
| clear_hub_feature(hdev, C_HUB_OVER_CURRENT); |
| hub_power_on(hub, true); |
| } |
| } |
| |
| loop_autopm: |
| /* Allow autosuspend if we're not going to run again */ |
| if (list_empty(&hub->event_list)) |
| usb_autopm_enable(intf); |
| loop: |
| usb_unlock_device(hdev); |
| kref_put(&hub->kref, hub_release); |
| |
| } /* end while (1) */ |
| } |
| |
| static int hub_thread(void *__unused) |
| { |
| /* khubd needs to be freezable to avoid intefering with USB-PERSIST |
| * port handover. Otherwise it might see that a full-speed device |
| * was gone before the EHCI controller had handed its port over to |
| * the companion full-speed controller. |
| */ |
| set_freezable(); |
| |
| do { |
| hub_events(); |
| wait_event_freezable(khubd_wait, |
| !list_empty(&hub_event_list) || |
| kthread_should_stop()); |
| } while (!kthread_should_stop() || !list_empty(&hub_event_list)); |
| |
| pr_debug("%s: khubd exiting\n", usbcore_name); |
| return 0; |
| } |
| |
| static struct usb_device_id hub_id_table [] = { |
| { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS, |
| .bDeviceClass = USB_CLASS_HUB}, |
| { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS, |
| .bInterfaceClass = USB_CLASS_HUB}, |
| { } /* Terminating entry */ |
| }; |
| |
| MODULE_DEVICE_TABLE (usb, hub_id_table); |
| |
| static struct usb_driver hub_driver = { |
| .name = "hub", |
| .probe = hub_probe, |
| .disconnect = hub_disconnect, |
| .suspend = hub_suspend, |
| .resume = hub_resume, |
| .reset_resume = hub_reset_resume, |
| .pre_reset = hub_pre_reset, |
| .post_reset = hub_post_reset, |
| .ioctl = hub_ioctl, |
| .id_table = hub_id_table, |
| .supports_autosuspend = 1, |
| }; |
| |
| int usb_hub_init(void) |
| { |
| if (usb_register(&hub_driver) < 0) { |
| printk(KERN_ERR "%s: can't register hub driver\n", |
| usbcore_name); |
| return -1; |
| } |
| |
| khubd_task = kthread_run(hub_thread, NULL, "khubd"); |
| if (!IS_ERR(khubd_task)) |
| return 0; |
| |
| /* Fall through if kernel_thread failed */ |
| usb_deregister(&hub_driver); |
| printk(KERN_ERR "%s: can't start khubd\n", usbcore_name); |
| |
| return -1; |
| } |
| |
| void usb_hub_cleanup(void) |
| { |
| kthread_stop(khubd_task); |
| |
| /* |
| * Hub resources are freed for us by usb_deregister. It calls |
| * usb_driver_purge on every device which in turn calls that |
| * devices disconnect function if it is using this driver. |
| * The hub_disconnect function takes care of releasing the |
| * individual hub resources. -greg |
| */ |
| usb_deregister(&hub_driver); |
| } /* usb_hub_cleanup() */ |
| |
| static int descriptors_changed(struct usb_device *udev, |
| struct usb_device_descriptor *old_device_descriptor) |
| { |
| int changed = 0; |
| unsigned index; |
| unsigned serial_len = 0; |
| unsigned len; |
| unsigned old_length; |
| int length; |
| char *buf; |
| |
| if (memcmp(&udev->descriptor, old_device_descriptor, |
| sizeof(*old_device_descriptor)) != 0) |
| return 1; |
| |
| /* Since the idVendor, idProduct, and bcdDevice values in the |
| * device descriptor haven't changed, we will assume the |
| * Manufacturer and Product strings haven't changed either. |
| * But the SerialNumber string could be different (e.g., a |
| * different flash card of the same brand). |
| */ |
| if (udev->serial) |
| serial_len = strlen(udev->serial) + 1; |
| |
| len = serial_len; |
| for (index = 0; index < udev->descriptor.bNumConfigurations; index++) { |
| old_length = le16_to_cpu(udev->config[index].desc.wTotalLength); |
| len = max(len, old_length); |
| } |
| |
| buf = kmalloc(len, GFP_NOIO); |
| if (buf == NULL) { |
| dev_err(&udev->dev, "no mem to re-read configs after reset\n"); |
| /* assume the worst */ |
| return 1; |
| } |
| for (index = 0; index < udev->descriptor.bNumConfigurations; index++) { |
| old_length = le16_to_cpu(udev->config[index].desc.wTotalLength); |
| length = usb_get_descriptor(udev, USB_DT_CONFIG, index, buf, |
| old_length); |
| if (length != old_length) { |
| dev_dbg(&udev->dev, "config index %d, error %d\n", |
| index, length); |
| changed = 1; |
| break; |
| } |
| if (memcmp (buf, udev->rawdescriptors[index], old_length) |
| != 0) { |
| dev_dbg(&udev->dev, "config index %d changed (#%d)\n", |
| index, |
| ((struct usb_config_descriptor *) buf)-> |
| bConfigurationValue); |
| changed = 1; |
| break; |
| } |
| } |
| |
| if (!changed && serial_len) { |
| length = usb_string(udev, udev->descriptor.iSerialNumber, |
| buf, serial_len); |
| if (length + 1 != serial_len) { |
| dev_dbg(&udev->dev, "serial string error %d\n", |
| length); |
| changed = 1; |
| } else if (memcmp(buf, udev->serial, length) != 0) { |
| dev_dbg(&udev->dev, "serial string changed\n"); |
| changed = 1; |
| } |
| } |
| |
| kfree(buf); |
| return changed; |
| } |
| |
| /** |
| * usb_reset_and_verify_device - perform a USB port reset to reinitialize a device |
| * @udev: device to reset (not in SUSPENDED or NOTATTACHED state) |
| * |
| * WARNING - don't use this routine to reset a composite device |
| * (one with multiple interfaces owned by separate drivers)! |
| * Use usb_reset_device() instead. |
| * |
| * Do a port reset, reassign the device's address, and establish its |
| * former operating configuration. If the reset fails, or the device's |
| * descriptors change from their values before the reset, or the original |
| * configuration and altsettings cannot be restored, a flag will be set |
| * telling khubd to pretend the device has been disconnected and then |
| * re-connected. All drivers will be unbound, and the device will be |
| * re-enumerated and probed all over again. |
| * |
| * Returns 0 if the reset succeeded, -ENODEV if the device has been |
| * flagged for logical disconnection, or some other negative error code |
| * if the reset wasn't even attempted. |
| * |
| * The caller must own the device lock. For example, it's safe to use |
| * this from a driver probe() routine after downloading new firmware. |
| * For calls that might not occur during probe(), drivers should lock |
| * the device using usb_lock_device_for_reset(). |
| * |
| * Locking exception: This routine may also be called from within an |
| * autoresume handler. Such usage won't conflict with other tasks |
| * holding the device lock because these tasks should always call |
| * usb_autopm_resume_device(), thereby preventing any unwanted autoresume. |
| */ |
| static int usb_reset_and_verify_device(struct usb_device *udev) |
| { |
| struct usb_device *parent_hdev = udev->parent; |
| struct usb_hub *parent_hub; |
| struct usb_device_descriptor descriptor = udev->descriptor; |
| int i, ret = 0; |
| int port1 = udev->portnum; |
| |
| if (udev->state == USB_STATE_NOTATTACHED || |
| udev->state == USB_STATE_SUSPENDED) { |
| dev_dbg(&udev->dev, "device reset not allowed in state %d\n", |
| udev->state); |
| return -EINVAL; |
| } |
| |
| if (!parent_hdev) { |
| /* this requires hcd-specific logic; see OHCI hc_restart() */ |
| dev_dbg(&udev->dev, "%s for root hub!\n", __func__); |
| return -EISDIR; |
| } |
| parent_hub = hdev_to_hub(parent_hdev); |
| |
| set_bit(port1, parent_hub->busy_bits); |
| for (i = 0; i < SET_CONFIG_TRIES; ++i) { |
| |
| /* ep0 maxpacket size may change; let the HCD know about it. |
| * Other endpoints will be handled by re-enumeration. */ |
| usb_ep0_reinit(udev); |
| ret = hub_port_init(parent_hub, udev, port1, i); |
| if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV) |
| break; |
| } |
| clear_bit(port1, parent_hub->busy_bits); |
| |
| if (ret < 0) |
| goto re_enumerate; |
| |
| /* Device might have changed firmware (DFU or similar) */ |
| if (descriptors_changed(udev, &descriptor)) { |
| dev_info(&udev->dev, "device firmware changed\n"); |
| udev->descriptor = descriptor; /* for disconnect() calls */ |
| goto re_enumerate; |
| } |
| |
| /* Restore the device's previous configuration */ |
| if (!udev->actconfig) |
| goto done; |
| ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0), |
| USB_REQ_SET_CONFIGURATION, 0, |
| udev->actconfig->desc.bConfigurationValue, 0, |
| NULL, 0, USB_CTRL_SET_TIMEOUT); |
| if (ret < 0) { |
| dev_err(&udev->dev, |
| "can't restore configuration #%d (error=%d)\n", |
| udev->actconfig->desc.bConfigurationValue, ret); |
| goto re_enumerate; |
| } |
| usb_set_device_state(udev, USB_STATE_CONFIGURED); |
| |
| /* Put interfaces back into the same altsettings as before. |
| * Don't bother to send the Set-Interface request for interfaces |
| * that were already in altsetting 0; besides being unnecessary, |
| * many devices can't handle it. Instead just reset the host-side |
| * endpoint state. |
| */ |
| for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) { |
| struct usb_interface *intf = udev->actconfig->interface[i]; |
| struct usb_interface_descriptor *desc; |
| |
| desc = &intf->cur_altsetting->desc; |
| if (desc->bAlternateSetting == 0) { |
| usb_disable_interface(udev, intf, true); |
| usb_enable_interface(udev, intf, true); |
| ret = 0; |
| } else { |
| ret = usb_set_interface(udev, desc->bInterfaceNumber, |
| desc->bAlternateSetting); |
| } |
| if (ret < 0) { |
| dev_err(&udev->dev, "failed to restore interface %d " |
| "altsetting %d (error=%d)\n", |
| desc->bInterfaceNumber, |
| desc->bAlternateSetting, |
| ret); |
| goto re_enumerate; |
| } |
| } |
| |
| done: |
| return 0; |
| |
| re_enumerate: |
| hub_port_logical_disconnect(parent_hub, port1); |
| return -ENODEV; |
| } |
| |
| /** |
| * usb_reset_device - warn interface drivers and perform a USB port reset |
| * @udev: device to reset (not in SUSPENDED or NOTATTACHED state) |
| * |
| * Warns all drivers bound to registered interfaces (using their pre_reset |
| * method), performs the port reset, and then lets the drivers know that |
| * the reset is over (using their post_reset method). |
| * |
| * Return value is the same as for usb_reset_and_verify_device(). |
| * |
| * The caller must own the device lock. For example, it's safe to use |
| * this from a driver probe() routine after downloading new firmware. |
| * For calls that might not occur during probe(), drivers should lock |
| * the device using usb_lock_device_for_reset(). |
| * |
| * If an interface is currently being probed or disconnected, we assume |
| * its driver knows how to handle resets. For all other interfaces, |
| * if the driver doesn't have pre_reset and post_reset methods then |
| * we attempt to unbind it and rebind afterward. |
| */ |
| int usb_reset_device(struct usb_device *udev) |
| { |
| int ret; |
| int i; |
| struct usb_host_config *config = udev->actconfig; |
| |
| if (udev->state == USB_STATE_NOTATTACHED || |
| udev->state == USB_STATE_SUSPENDED) { |
| dev_dbg(&udev->dev, "device reset not allowed in state %d\n", |
| udev->state); |
| return -EINVAL; |
| } |
| |
| /* Prevent autosuspend during the reset */ |
| usb_autoresume_device(udev); |
| |
| if (config) { |
| for (i = 0; i < config->desc.bNumInterfaces; ++i) { |
| struct usb_interface *cintf = config->interface[i]; |
| struct usb_driver *drv; |
| int unbind = 0; |
| |
| if (cintf->dev.driver) { |
| drv = to_usb_driver(cintf->dev.driver); |
| if (drv->pre_reset && drv->post_reset) |
| unbind = (drv->pre_reset)(cintf); |
| else if (cintf->condition == |
| USB_INTERFACE_BOUND) |
| unbind = 1; |
| if (unbind) |
| usb_forced_unbind_intf(cintf); |
| } |
| } |
| } |
| |
| ret = usb_reset_and_verify_device(udev); |
| |
| if (config) { |
| for (i = config->desc.bNumInterfaces - 1; i >= 0; --i) { |
| struct usb_interface *cintf = config->interface[i]; |
| struct usb_driver *drv; |
| int rebind = cintf->needs_binding; |
| |
| if (!rebind && cintf->dev.driver) { |
| drv = to_usb_driver(cintf->dev.driver); |
| if (drv->post_reset) |
| rebind = (drv->post_reset)(cintf); |
| else if (cintf->condition == |
| USB_INTERFACE_BOUND) |
| rebind = 1; |
| } |
| if (ret == 0 && rebind) |
| usb_rebind_intf(cintf); |
| } |
| } |
| |
| usb_autosuspend_device(udev); |
| return ret; |
| } |
| EXPORT_SYMBOL_GPL(usb_reset_device); |
| |
| |
| /** |
| * usb_queue_reset_device - Reset a USB device from an atomic context |
| * @iface: USB interface belonging to the device to reset |
| * |
| * This function can be used to reset a USB device from an atomic |
| * context, where usb_reset_device() won't work (as it blocks). |
| * |
| * Doing a reset via this method is functionally equivalent to calling |
| * usb_reset_device(), except for the fact that it is delayed to a |
| * workqueue. This means that any drivers bound to other interfaces |
| * might be unbound, as well as users from usbfs in user space. |
| * |
| * Corner cases: |
| * |
| * - Scheduling two resets at the same time from two different drivers |
| * attached to two different interfaces of the same device is |
| * possible; depending on how the driver attached to each interface |
| * handles ->pre_reset(), the second reset might happen or not. |
| * |
| * - If a driver is unbound and it had a pending reset, the reset will |
| * be cancelled. |
| * |
| * - This function can be called during .probe() or .disconnect() |
| * times. On return from .disconnect(), any pending resets will be |
| * cancelled. |
| * |
| * There is no no need to lock/unlock the @reset_ws as schedule_work() |
| * does its own. |
| * |
| * NOTE: We don't do any reference count tracking because it is not |
| * needed. The lifecycle of the work_struct is tied to the |
| * usb_interface. Before destroying the interface we cancel the |
| * work_struct, so the fact that work_struct is queued and or |
| * running means the interface (and thus, the device) exist and |
| * are referenced. |
| */ |
| void usb_queue_reset_device(struct usb_interface *iface) |
| { |
| schedule_work(&iface->reset_ws); |
| } |
| EXPORT_SYMBOL_GPL(usb_queue_reset_device); |