| # |
| # Sensor device configuration |
| # |
| |
| menu "I2C Hardware Bus support" |
| depends on HAS_IOMEM |
| |
| comment "PC SMBus host controller drivers" |
| depends on PCI |
| |
| config I2C_ALI1535 |
| tristate "ALI 1535" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the SMB |
| Host controller on Acer Labs Inc. (ALI) M1535 South Bridges. The SMB |
| controller is part of the 7101 device, which is an ACPI-compliant |
| Power Management Unit (PMU). |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-ali1535. |
| |
| config I2C_ALI1563 |
| tristate "ALI 1563" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the SMB |
| Host controller on Acer Labs Inc. (ALI) M1563 South Bridges. The SMB |
| controller is part of the 7101 device, which is an ACPI-compliant |
| Power Management Unit (PMU). |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-ali1563. |
| |
| config I2C_ALI15X3 |
| tristate "ALI 15x3" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the |
| Acer Labs Inc. (ALI) M1514 and M1543 motherboard I2C interfaces. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-ali15x3. |
| |
| config I2C_AMD756 |
| tristate "AMD 756/766/768/8111 and nVidia nForce" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the AMD |
| 756/766/768 mainboard I2C interfaces. The driver also includes |
| support for the first (SMBus 1.0) I2C interface of the AMD 8111 and |
| the nVidia nForce I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-amd756. |
| |
| config I2C_AMD756_S4882 |
| tristate "SMBus multiplexing on the Tyan S4882" |
| depends on I2C_AMD756 && X86 |
| help |
| Enabling this option will add specific SMBus support for the Tyan |
| S4882 motherboard. On this 4-CPU board, the SMBus is multiplexed |
| over 8 different channels, where the various memory module EEPROMs |
| and temperature sensors live. Saying yes here will give you access |
| to these in addition to the trunk. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-amd756-s4882. |
| |
| config I2C_AMD8111 |
| tristate "AMD 8111" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the |
| second (SMBus 2.0) AMD 8111 mainboard I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-amd8111. |
| |
| config I2C_HIX5HD2 |
| tristate "Hix5hd2 high-speed I2C driver" |
| depends on ARCH_HISI || ARCH_HIX5HD2 || COMPILE_TEST |
| help |
| Say Y here to include support for the high-speed I2C controller |
| used in HiSilicon hix5hd2 SoCs. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-hix5hd2. |
| |
| config I2C_I801 |
| tristate "Intel 82801 (ICH/PCH)" |
| depends on PCI |
| select CHECK_SIGNATURE if X86 && DMI |
| select I2C_SMBUS |
| help |
| If you say yes to this option, support will be included for the Intel |
| 801 family of mainboard I2C interfaces. Specifically, the following |
| versions of the chipset are supported: |
| 82801AA |
| 82801AB |
| 82801BA |
| 82801CA/CAM |
| 82801DB |
| 82801EB/ER (ICH5/ICH5R) |
| 6300ESB |
| ICH6 |
| ICH7 |
| ESB2 |
| ICH8 |
| ICH9 |
| EP80579 (Tolapai) |
| ICH10 |
| 5/3400 Series (PCH) |
| 6 Series (PCH) |
| Patsburg (PCH) |
| DH89xxCC (PCH) |
| Panther Point (PCH) |
| Lynx Point (PCH) |
| Lynx Point-LP (PCH) |
| Avoton (SOC) |
| Wellsburg (PCH) |
| Coleto Creek (PCH) |
| Wildcat Point (PCH) |
| Wildcat Point-LP (PCH) |
| BayTrail (SOC) |
| Sunrise Point-H (PCH) |
| Sunrise Point-LP (PCH) |
| DNV (SOC) |
| Broxton (SOC) |
| Lewisburg (PCH) |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-i801. |
| |
| config I2C_ISCH |
| tristate "Intel SCH SMBus 1.0" |
| depends on PCI |
| select LPC_SCH |
| help |
| Say Y here if you want to use SMBus controller on the Intel SCH |
| based systems. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-isch. |
| |
| config I2C_ISMT |
| tristate "Intel iSMT SMBus Controller" |
| depends on PCI && X86 |
| help |
| If you say yes to this option, support will be included for the Intel |
| iSMT SMBus host controller interface. |
| |
| This driver can also be built as a module. If so, the module will be |
| called i2c-ismt. |
| |
| config I2C_PIIX4 |
| tristate "Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC)" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the Intel |
| PIIX4 family of mainboard I2C interfaces. Specifically, the following |
| versions of the chipset are supported (note that Serverworks is part |
| of Broadcom): |
| Intel PIIX4 |
| Intel 440MX |
| ATI IXP200 |
| ATI IXP300 |
| ATI IXP400 |
| ATI SB600 |
| ATI SB700/SP5100 |
| ATI SB800 |
| AMD Hudson-2 |
| AMD ML |
| AMD CZ |
| Serverworks OSB4 |
| Serverworks CSB5 |
| Serverworks CSB6 |
| Serverworks HT-1000 |
| Serverworks HT-1100 |
| SMSC Victory66 |
| |
| Some AMD chipsets contain two PIIX4-compatible SMBus |
| controllers. This driver will attempt to use both controllers |
| on the SB700/SP5100, if they have been initialized by the BIOS. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-piix4. |
| |
| config I2C_NFORCE2 |
| tristate "Nvidia nForce2, nForce3 and nForce4" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the Nvidia |
| nForce2, nForce3 and nForce4 families of mainboard I2C interfaces. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-nforce2. |
| |
| config I2C_NFORCE2_S4985 |
| tristate "SMBus multiplexing on the Tyan S4985" |
| depends on I2C_NFORCE2 && X86 |
| help |
| Enabling this option will add specific SMBus support for the Tyan |
| S4985 motherboard. On this 4-CPU board, the SMBus is multiplexed |
| over 4 different channels, where the various memory module EEPROMs |
| live. Saying yes here will give you access to these in addition |
| to the trunk. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-nforce2-s4985. |
| |
| config I2C_SIS5595 |
| tristate "SiS 5595" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the |
| SiS5595 SMBus (a subset of I2C) interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sis5595. |
| |
| config I2C_SIS630 |
| tristate "SiS 630/730/964" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the |
| SiS630, SiS730 and SiS964 SMBus (a subset of I2C) interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sis630. |
| |
| config I2C_SIS96X |
| tristate "SiS 96x" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the SiS |
| 96x SMBus (a subset of I2C) interfaces. Specifically, the following |
| chipsets are supported: |
| 645/961 |
| 645DX/961 |
| 645DX/962 |
| 648/961 |
| 650/961 |
| 735 |
| 745 |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sis96x. |
| |
| config I2C_VIA |
| tristate "VIA VT82C586B" |
| depends on PCI |
| select I2C_ALGOBIT |
| help |
| If you say yes to this option, support will be included for the VIA |
| 82C586B I2C interface |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-via. |
| |
| config I2C_VIAPRO |
| tristate "VIA VT82C596/82C686/82xx and CX700/VX8xx/VX900" |
| depends on PCI |
| help |
| If you say yes to this option, support will be included for the VIA |
| VT82C596 and later SMBus interface. Specifically, the following |
| chipsets are supported: |
| VT82C596A/B |
| VT82C686A/B |
| VT8231 |
| VT8233/A |
| VT8235 |
| VT8237R/A/S |
| VT8251 |
| CX700 |
| VX800/VX820 |
| VX855/VX875 |
| VX900 |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-viapro. |
| |
| if ACPI |
| |
| comment "ACPI drivers" |
| |
| config I2C_SCMI |
| tristate "SMBus Control Method Interface" |
| help |
| This driver supports the SMBus Control Method Interface. It needs the |
| BIOS to declare ACPI control methods as described in the SMBus Control |
| Method Interface specification. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called i2c-scmi. |
| |
| endif # ACPI |
| |
| comment "Mac SMBus host controller drivers" |
| depends on PPC_CHRP || PPC_PMAC |
| |
| config I2C_HYDRA |
| tristate "CHRP Apple Hydra Mac I/O I2C interface" |
| depends on PCI && PPC_CHRP |
| select I2C_ALGOBIT |
| help |
| This supports the use of the I2C interface in the Apple Hydra Mac |
| I/O chip on some CHRP machines (e.g. the LongTrail). Say Y if you |
| have such a machine. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-hydra. |
| |
| config I2C_POWERMAC |
| tristate "Powermac I2C interface" |
| depends on PPC_PMAC |
| default y |
| help |
| This exposes the various PowerMac i2c interfaces to the linux i2c |
| layer and to userland. It is used by various drivers on the PowerMac |
| platform, and should generally be enabled. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-powermac. |
| |
| comment "I2C system bus drivers (mostly embedded / system-on-chip)" |
| |
| config I2C_AT91 |
| tristate "Atmel AT91 I2C Two-Wire interface (TWI)" |
| depends on ARCH_AT91 |
| help |
| This supports the use of the I2C interface on Atmel AT91 |
| processors. |
| |
| A serious problem is that there is no documented way to issue |
| repeated START conditions for more than two messages, as needed |
| to support combined I2C messages. Use the i2c-gpio driver |
| unless your system can cope with this limitation. |
| |
| Caution! at91rm9200, at91sam9261, at91sam9260, at91sam9263 devices |
| don't have clock stretching in transmission mode. For that reason, |
| you can encounter underrun issues causing premature stop sendings if |
| the latency to fill the transmission register is too long. If you |
| are facing this situation, use the i2c-gpio driver. |
| |
| config I2C_AU1550 |
| tristate "Au1550/Au1200/Au1300 SMBus interface" |
| depends on MIPS_ALCHEMY |
| help |
| If you say yes to this option, support will be included for the |
| Au1550/Au1200/Au1300 SMBus interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-au1550. |
| |
| config I2C_AXXIA |
| tristate "Axxia I2C controller" |
| depends on ARCH_AXXIA || COMPILE_TEST |
| default ARCH_AXXIA |
| help |
| Say yes if you want to support the I2C bus on Axxia platforms. |
| |
| Please note that this controller is limited to transfers of maximum |
| 255 bytes in length. Any attempt to to a larger transfer will return |
| an error. |
| |
| config I2C_BCM2835 |
| tristate "Broadcom BCM2835 I2C controller" |
| depends on ARCH_BCM2835 |
| help |
| If you say yes to this option, support will be included for the |
| BCM2835 I2C controller. |
| |
| If you don't know what to do here, say N. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-bcm2835. |
| |
| config I2C_BCM_IPROC |
| tristate "Broadcom iProc I2C controller" |
| depends on ARCH_BCM_IPROC || COMPILE_TEST |
| default ARCH_BCM_IPROC |
| help |
| If you say yes to this option, support will be included for the |
| Broadcom iProc I2C controller. |
| |
| If you don't know what to do here, say N. |
| |
| config I2C_BCM_KONA |
| tristate "BCM Kona I2C adapter" |
| depends on ARCH_BCM_MOBILE |
| default y |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface on the Broadcom Kona family of processors. |
| |
| If you do not need KONA I2C interface, say N. |
| |
| config I2C_BRCMSTB |
| tristate "BRCM Settop I2C controller" |
| depends on ARCH_BRCMSTB || BMIPS_GENERIC || COMPILE_TEST |
| default y |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface on the Broadcom Settop SoCs. |
| |
| If you do not need I2C interface, say N. |
| |
| config I2C_BLACKFIN_TWI |
| tristate "Blackfin TWI I2C support" |
| depends on BLACKFIN |
| depends on !BF561 && !BF531 && !BF532 && !BF533 |
| help |
| This is the I2C bus driver for Blackfin on-chip TWI interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-bfin-twi. |
| |
| config I2C_BLACKFIN_TWI_CLK_KHZ |
| int "Blackfin TWI I2C clock (kHz)" |
| depends on I2C_BLACKFIN_TWI |
| range 21 400 |
| default 50 |
| help |
| The unit of the TWI clock is kHz. |
| |
| config I2C_CADENCE |
| tristate "Cadence I2C Controller" |
| depends on ARCH_ZYNQ || ARM64 |
| help |
| Say yes here to select Cadence I2C Host Controller. This controller is |
| e.g. used by Xilinx Zynq. |
| |
| config I2C_CBUS_GPIO |
| tristate "CBUS I2C driver" |
| depends on GPIOLIB || COMPILE_TEST |
| help |
| Support for CBUS access using I2C API. Mostly relevant for Nokia |
| Internet Tablets (770, N800 and N810). |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-cbus-gpio. |
| |
| config I2C_CPM |
| tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)" |
| depends on CPM1 || CPM2 |
| help |
| This supports the use of the I2C interface on Freescale |
| processors with CPM1 or CPM2. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-cpm. |
| |
| config I2C_DAVINCI |
| tristate "DaVinci I2C driver" |
| depends on ARCH_DAVINCI || ARCH_KEYSTONE |
| help |
| Support for TI DaVinci I2C controller driver. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-davinci. |
| |
| Please note that this driver might be needed to bring up other |
| devices such as DaVinci NIC. |
| For details please see http://www.ti.com/davinci |
| |
| config I2C_DESIGNWARE_CORE |
| tristate |
| |
| config I2C_DESIGNWARE_PLATFORM |
| tristate "Synopsys DesignWare Platform" |
| select I2C_DESIGNWARE_CORE |
| depends on (ACPI && COMMON_CLK) || !ACPI |
| help |
| If you say yes to this option, support will be included for the |
| Synopsys DesignWare I2C adapter. Only master mode is supported. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-designware-platform. |
| |
| config I2C_DESIGNWARE_PCI |
| tristate "Synopsys DesignWare PCI" |
| depends on PCI |
| select I2C_DESIGNWARE_CORE |
| help |
| If you say yes to this option, support will be included for the |
| Synopsys DesignWare I2C adapter. Only master mode is supported. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-designware-pci. |
| |
| config I2C_DESIGNWARE_BAYTRAIL |
| bool "Intel Baytrail I2C semaphore support" |
| depends on ACPI |
| depends on (I2C_DESIGNWARE_PLATFORM=m && IOSF_MBI) || \ |
| (I2C_DESIGNWARE_PLATFORM=y && IOSF_MBI=y) |
| help |
| This driver enables managed host access to the PMIC I2C bus on select |
| Intel BayTrail platforms using the X-Powers AXP288 PMIC. It allows |
| the host to request uninterrupted access to the PMIC's I2C bus from |
| the platform firmware controlling it. You should say Y if running on |
| a BayTrail system using the AXP288. |
| |
| config I2C_DIGICOLOR |
| tristate "Conexant Digicolor I2C driver" |
| depends on ARCH_DIGICOLOR |
| help |
| Support for Conexant Digicolor SoCs (CX92755) I2C controller driver. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-digicolor. |
| |
| config I2C_EFM32 |
| tristate "EFM32 I2C controller" |
| depends on ARCH_EFM32 || COMPILE_TEST |
| help |
| This driver supports the i2c block found in Energy Micro's EFM32 |
| SoCs. |
| |
| config I2C_EG20T |
| tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) I2C" |
| depends on PCI && (X86_32 || MIPS || COMPILE_TEST) |
| help |
| This driver is for PCH(Platform controller Hub) I2C of EG20T which |
| is an IOH(Input/Output Hub) for x86 embedded processor. |
| This driver can access PCH I2C bus device. |
| |
| This driver also can be used for LAPIS Semiconductor IOH(Input/ |
| Output Hub), ML7213, ML7223 and ML7831. |
| ML7213 IOH is for IVI(In-Vehicle Infotainment) use, ML7223 IOH is |
| for MP(Media Phone) use and ML7831 IOH is for general purpose use. |
| ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series. |
| ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH. |
| |
| config I2C_EMEV2 |
| tristate "EMMA Mobile series I2C adapter" |
| depends on HAVE_CLK |
| select I2C_SLAVE |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface on the Renesas Electronics EM/EV family of processors. |
| |
| config I2C_EXYNOS5 |
| tristate "Exynos5 high-speed I2C driver" |
| depends on ARCH_EXYNOS && OF |
| default y |
| help |
| High-speed I2C controller on Exynos5 based Samsung SoCs. |
| |
| config I2C_GPIO |
| tristate "GPIO-based bitbanging I2C" |
| depends on GPIOLIB || COMPILE_TEST |
| select I2C_ALGOBIT |
| help |
| This is a very simple bitbanging I2C driver utilizing the |
| arch-neutral GPIO API to control the SCL and SDA lines. |
| |
| config I2C_HIGHLANDER |
| tristate "Highlander FPGA SMBus interface" |
| depends on SH_HIGHLANDER |
| help |
| If you say yes to this option, support will be included for |
| the SMBus interface located in the FPGA on various Highlander |
| boards, particularly the R0P7780LC0011RL and R0P7785LC0011RL |
| FPGAs. This is wholly unrelated to the SoC I2C. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-highlander. |
| |
| config I2C_IBM_IIC |
| tristate "IBM PPC 4xx on-chip I2C interface" |
| depends on 4xx |
| help |
| Say Y here if you want to use IIC peripheral found on |
| embedded IBM PPC 4xx based systems. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-ibm_iic. |
| |
| config I2C_IMG |
| tristate "Imagination Technologies I2C SCB Controller" |
| depends on MIPS || METAG || COMPILE_TEST |
| help |
| Say Y here if you want to use the IMG I2C SCB controller, |
| available on the TZ1090 and other IMG SoCs. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-img-scb. |
| |
| config I2C_IMX |
| tristate "IMX I2C interface" |
| depends on ARCH_MXC || ARCH_LAYERSCAPE || COLDFIRE |
| help |
| Say Y here if you want to use the IIC bus controller on |
| the Freescale i.MX/MXC, Layerscape or ColdFire processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-imx. |
| |
| config I2C_IOP3XX |
| tristate "Intel IOPx3xx and IXP4xx on-chip I2C interface" |
| depends on ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX || ARCH_IOP13XX |
| help |
| Say Y here if you want to use the IIC bus controller on |
| the Intel IOPx3xx I/O Processors or IXP4xx Network Processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-iop3xx. |
| |
| config I2C_JZ4780 |
| tristate "JZ4780 I2C controller interface support" |
| depends on MACH_JZ4780 || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for the |
| Ingenic JZ4780 I2C controller. |
| |
| If you don't know what to do here, say N. |
| |
| config I2C_KEMPLD |
| tristate "Kontron COM I2C Controller" |
| depends on MFD_KEMPLD |
| help |
| This enables support for the I2C bus interface on some Kontron ETX |
| and COMexpress (ETXexpress) modules. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-kempld. |
| |
| config I2C_LPC2K |
| tristate "I2C bus support for NXP LPC2K/LPC178x/18xx/43xx" |
| depends on OF && (ARCH_LPC18XX || COMPILE_TEST) |
| help |
| This driver supports the I2C interface found several NXP |
| devices including LPC2xxx, LPC178x/7x and LPC18xx/43xx. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-lpc2k. |
| |
| config I2C_MESON |
| tristate "Amlogic Meson I2C controller" |
| depends on ARCH_MESON || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface on the Amlogic Meson family of SoCs. |
| |
| config I2C_MPC |
| tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx" |
| depends on PPC |
| help |
| If you say yes to this option, support will be included for the |
| built-in I2C interface on the MPC107, Tsi107, MPC512x, MPC52xx, |
| MPC8240, MPC8245, MPC83xx, MPC85xx and MPC8641 family processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-mpc. |
| |
| config I2C_MT65XX |
| tristate "MediaTek I2C adapter" |
| depends on ARCH_MEDIATEK || COMPILE_TEST |
| depends on HAS_DMA |
| help |
| This selects the MediaTek(R) Integrated Inter Circuit bus driver |
| for MT65xx and MT81xx. |
| If you want to use MediaTek(R) I2C interface, say Y or M here. |
| If unsure, say N. |
| |
| config I2C_MV64XXX |
| tristate "Marvell mv64xxx I2C Controller" |
| depends on MV64X60 || PLAT_ORION || ARCH_SUNXI || ARCH_MVEBU |
| help |
| If you say yes to this option, support will be included for the |
| built-in I2C interface on the Marvell 64xxx line of host bridges. |
| This driver is also used for Allwinner SoCs I2C controllers. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-mv64xxx. |
| |
| config I2C_MXS |
| tristate "Freescale i.MX28 I2C interface" |
| depends on SOC_IMX28 |
| select STMP_DEVICE |
| help |
| Say Y here if you want to use the I2C bus controller on |
| the Freescale i.MX28 processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-mxs. |
| |
| config I2C_NOMADIK |
| tristate "ST-Ericsson Nomadik/Ux500 I2C Controller" |
| depends on ARM_AMBA |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface from ST-Ericsson's Nomadik and Ux500 architectures, |
| as well as the STA2X11 PCIe I/O HUB. |
| |
| config I2C_OCORES |
| tristate "OpenCores I2C Controller" |
| help |
| If you say yes to this option, support will be included for the |
| OpenCores I2C controller. For details see |
| http://www.opencores.org/projects.cgi/web/i2c/overview |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-ocores. |
| |
| config I2C_OMAP |
| tristate "OMAP I2C adapter" |
| depends on ARCH_OMAP |
| default y if MACH_OMAP_H3 || MACH_OMAP_OSK |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface on the Texas Instruments OMAP1/2 family of processors. |
| Like OMAP1510/1610/1710/5912 and OMAP242x. |
| For details see http://www.ti.com/omap. |
| |
| config I2C_PASEMI |
| tristate "PA Semi SMBus interface" |
| depends on PPC_PASEMI && PCI |
| help |
| Supports the PA Semi PWRficient on-chip SMBus interfaces. |
| |
| config I2C_PCA_PLATFORM |
| tristate "PCA9564/PCA9665 as platform device" |
| select I2C_ALGOPCA |
| default n |
| help |
| This driver supports a memory mapped Philips PCA9564/PCA9665 |
| parallel bus to I2C bus controller. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-pca-platform. |
| |
| config I2C_PMCMSP |
| tristate "PMC MSP I2C TWI Controller" |
| depends on PMC_MSP |
| help |
| This driver supports the PMC TWI controller on MSP devices. |
| |
| This driver can also be built as module. If so, the module |
| will be called i2c-pmcmsp. |
| |
| config I2C_PNX |
| tristate "I2C bus support for Philips PNX and NXP LPC targets" |
| depends on ARCH_LPC32XX |
| help |
| This driver supports the Philips IP3204 I2C IP block master and/or |
| slave controller |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-pnx. |
| |
| config I2C_PUV3 |
| tristate "PKUnity v3 I2C bus support" |
| depends on UNICORE32 && ARCH_PUV3 |
| select I2C_ALGOBIT |
| help |
| This driver supports the I2C IP inside the PKUnity-v3 SoC. |
| This I2C bus controller is under AMBA/AXI bus. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-puv3. |
| |
| config I2C_PXA |
| tristate "Intel PXA2XX I2C adapter" |
| depends on ARCH_PXA || ARCH_MMP || (X86_32 && PCI && OF) |
| help |
| If you have devices in the PXA I2C bus, say yes to this option. |
| This driver can also be built as a module. If so, the module |
| will be called i2c-pxa. |
| |
| config I2C_PXA_PCI |
| def_bool I2C_PXA && X86_32 && PCI && OF |
| |
| config I2C_PXA_SLAVE |
| bool "Intel PXA2XX I2C Slave comms support" |
| depends on I2C_PXA && !X86_32 |
| help |
| Support I2C slave mode communications on the PXA I2C bus. This |
| is necessary for systems where the PXA may be a target on the |
| I2C bus. |
| |
| config I2C_QUP |
| tristate "Qualcomm QUP based I2C controller" |
| depends on ARCH_QCOM |
| help |
| If you say yes to this option, support will be included for the |
| built-in I2C interface on the Qualcomm SoCs. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-qup. |
| |
| config I2C_RIIC |
| tristate "Renesas RIIC adapter" |
| depends on ARCH_RENESAS || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for the |
| Renesas RIIC I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-riic. |
| |
| config I2C_RK3X |
| tristate "Rockchip RK3xxx I2C adapter" |
| depends on OF && COMMON_CLK |
| help |
| Say Y here to include support for the I2C adapter in Rockchip RK3xxx |
| SoCs. |
| |
| This driver can also be built as a module. If so, the module will |
| be called i2c-rk3x. |
| |
| config HAVE_S3C2410_I2C |
| bool |
| help |
| This will include I2C support for Samsung SoCs. If you want to |
| include I2C support for any machine, kindly select this in the |
| respective Kconfig file. |
| |
| config I2C_S3C2410 |
| tristate "S3C2410 I2C Driver" |
| depends on HAVE_S3C2410_I2C |
| help |
| Say Y here to include support for I2C controller in the |
| Samsung SoCs. |
| |
| config I2C_SH7760 |
| tristate "Renesas SH7760 I2C Controller" |
| depends on CPU_SUBTYPE_SH7760 |
| help |
| This driver supports the 2 I2C interfaces on the Renesas SH7760. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sh7760. |
| |
| config I2C_SH_MOBILE |
| tristate "SuperH Mobile I2C Controller" |
| depends on HAS_DMA |
| depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for the |
| built-in I2C interface on the Renesas SH-Mobile processor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sh_mobile. |
| |
| config I2C_SIMTEC |
| tristate "Simtec Generic I2C interface" |
| select I2C_ALGOBIT |
| help |
| If you say yes to this option, support will be included for |
| the Simtec Generic I2C interface. This driver is for the |
| simple I2C bus used on newer Simtec products for general |
| I2C, such as DDC on the Simtec BBD2016A. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-simtec. |
| |
| config I2C_SIRF |
| tristate "CSR SiRFprimaII I2C interface" |
| depends on ARCH_SIRF |
| help |
| If you say yes to this option, support will be included for the |
| CSR SiRFprimaII I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-sirf. |
| |
| config I2C_ST |
| tristate "STMicroelectronics SSC I2C support" |
| depends on ARCH_STI |
| help |
| Enable this option to add support for STMicroelectronics SoCs |
| hardware SSC (Synchronous Serial Controller) as an I2C controller. |
| |
| This driver can also be built as module. If so, the module |
| will be called i2c-st. |
| |
| config I2C_STU300 |
| tristate "ST Microelectronics DDC I2C interface" |
| depends on MACH_U300 |
| default y if MACH_U300 |
| help |
| If you say yes to this option, support will be included for the |
| I2C interface from ST Microelectronics simply called "DDC I2C" |
| supporting both I2C and DDC, used in e.g. the U300 series |
| mobile platforms. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-stu300. |
| |
| config I2C_SUN6I_P2WI |
| tristate "Allwinner sun6i internal P2WI controller" |
| depends on RESET_CONTROLLER |
| depends on MACH_SUN6I || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for the |
| P2WI (Push/Pull 2 Wire Interface) controller embedded in some sunxi |
| SOCs. |
| The P2WI looks like an SMBus controller (which supports only byte |
| accesses), except that it only supports one slave device. |
| This interface is used to connect to specific PMIC devices (like the |
| AXP221). |
| |
| config I2C_TEGRA |
| tristate "NVIDIA Tegra internal I2C controller" |
| depends on ARCH_TEGRA |
| help |
| If you say yes to this option, support will be included for the |
| I2C controller embedded in NVIDIA Tegra SOCs |
| |
| config I2C_UNIPHIER |
| tristate "UniPhier FIFO-less I2C controller" |
| depends on ARCH_UNIPHIER || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for |
| the UniPhier FIFO-less I2C interface embedded in PH1-LD4, PH1-sLD8, |
| or older UniPhier SoCs. |
| |
| config I2C_UNIPHIER_F |
| tristate "UniPhier FIFO-builtin I2C controller" |
| depends on ARCH_UNIPHIER || COMPILE_TEST |
| help |
| If you say yes to this option, support will be included for |
| the UniPhier FIFO-builtin I2C interface embedded in PH1-Pro4, |
| PH1-Pro5, or newer UniPhier SoCs. |
| |
| config I2C_VERSATILE |
| tristate "ARM Versatile/Realview I2C bus support" |
| depends on ARCH_VERSATILE || ARCH_REALVIEW || ARCH_VEXPRESS || COMPILE_TEST |
| select I2C_ALGOBIT |
| help |
| Say yes if you want to support the I2C serial bus on ARMs Versatile |
| range of platforms. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-versatile. |
| |
| config I2C_WMT |
| tristate "Wondermedia WM8xxx SoC I2C bus support" |
| depends on ARCH_VT8500 |
| help |
| Say yes if you want to support the I2C bus on Wondermedia 8xxx-series |
| SoCs. |
| |
| This driver can also be built as a module. If so, the module will be |
| called i2c-wmt. |
| |
| config I2C_OCTEON |
| tristate "Cavium OCTEON I2C bus support" |
| depends on CAVIUM_OCTEON_SOC |
| help |
| Say yes if you want to support the I2C serial bus on Cavium |
| OCTEON SOC. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-octeon. |
| |
| config I2C_THUNDERX |
| tristate "Cavium ThunderX I2C bus support" |
| depends on 64BIT && PCI && (ARM64 || COMPILE_TEST) |
| select I2C_SMBUS |
| help |
| Say yes if you want to support the I2C serial bus on Cavium |
| ThunderX SOC. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-thunderx. |
| |
| config I2C_XILINX |
| tristate "Xilinx I2C Controller" |
| depends on HAS_IOMEM |
| help |
| If you say yes to this option, support will be included for the |
| Xilinx I2C controller. |
| |
| This driver can also be built as a module. If so, the module |
| will be called xilinx_i2c. |
| |
| config I2C_XLR |
| tristate "Netlogic XLR and Sigma Designs I2C support" |
| depends on CPU_XLR || ARCH_TANGO |
| help |
| This driver enables support for the on-chip I2C interface of |
| the Netlogic XLR/XLS MIPS processors and Sigma Designs SOCs. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-xlr. |
| |
| config I2C_XLP9XX |
| tristate "XLP9XX I2C support" |
| depends on CPU_XLP || ARCH_VULCAN || COMPILE_TEST |
| help |
| This driver enables support for the on-chip I2C interface of |
| the Broadcom XLP9xx/XLP5xx MIPS and Vulcan ARM64 processors. |
| |
| This driver can also be built as a module. If so, the module will |
| be called i2c-xlp9xx. |
| |
| config I2C_RCAR |
| tristate "Renesas R-Car I2C Controller" |
| depends on HAS_DMA |
| depends on ARCH_RENESAS || COMPILE_TEST |
| select I2C_SLAVE |
| help |
| If you say yes to this option, support will be included for the |
| R-Car I2C controller. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-rcar. |
| |
| comment "External I2C/SMBus adapter drivers" |
| |
| config I2C_DIOLAN_U2C |
| tristate "Diolan U2C-12 USB adapter" |
| depends on USB |
| help |
| If you say yes to this option, support will be included for Diolan |
| U2C-12, a USB to I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-diolan-u2c. |
| |
| config I2C_DLN2 |
| tristate "Diolan DLN-2 USB I2C adapter" |
| depends on MFD_DLN2 |
| help |
| If you say yes to this option, support will be included for Diolan |
| DLN2, a USB to I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-dln2. |
| |
| config I2C_PARPORT |
| tristate "Parallel port adapter" |
| depends on PARPORT |
| select I2C_ALGOBIT |
| select I2C_SMBUS |
| help |
| This supports parallel port I2C adapters such as the ones made by |
| Philips or Velleman, Analog Devices evaluation boards, and more. |
| Basically any adapter using the parallel port as an I2C bus with |
| no extra chipset is supported by this driver, or could be. |
| |
| This driver is a replacement for (and was inspired by) an older |
| driver named i2c-philips-par. The new driver supports more devices, |
| and makes it easier to add support for new devices. |
| |
| An adapter type parameter is now mandatory. Please read the file |
| Documentation/i2c/busses/i2c-parport for details. |
| |
| Another driver exists, named i2c-parport-light, which doesn't depend |
| on the parport driver. This is meant for embedded systems. Don't say |
| Y here if you intend to say Y or M there. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-parport. |
| |
| config I2C_PARPORT_LIGHT |
| tristate "Parallel port adapter (light)" |
| select I2C_ALGOBIT |
| select I2C_SMBUS |
| help |
| This supports parallel port I2C adapters such as the ones made by |
| Philips or Velleman, Analog Devices evaluation boards, and more. |
| Basically any adapter using the parallel port as an I2C bus with |
| no extra chipset is supported by this driver, or could be. |
| |
| This driver is a light version of i2c-parport. It doesn't depend |
| on the parport driver, and uses direct I/O access instead. This |
| might be preferred on embedded systems where wasting memory for |
| the clean but heavy parport handling is not an option. The |
| drawback is a reduced portability and the impossibility to |
| daisy-chain other parallel port devices. |
| |
| Don't say Y here if you said Y or M to i2c-parport. Saying M to |
| both is possible but both modules should not be loaded at the same |
| time. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-parport-light. |
| |
| config I2C_ROBOTFUZZ_OSIF |
| tristate "RobotFuzz Open Source InterFace USB adapter" |
| depends on USB |
| help |
| If you say yes to this option, support will be included for the |
| RobotFuzz Open Source InterFace USB to I2C interface. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-osif. |
| |
| config I2C_TAOS_EVM |
| tristate "TAOS evaluation module" |
| depends on TTY |
| select SERIO |
| select SERIO_SERPORT |
| default n |
| help |
| This supports TAOS evaluation modules on serial port. In order to |
| use this driver, you will need the inputattach tool, which is part |
| of the input-utils package. |
| |
| If unsure, say N. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-taos-evm. |
| |
| config I2C_TINY_USB |
| tristate "Tiny-USB adapter" |
| depends on USB |
| help |
| If you say yes to this option, support will be included for the |
| i2c-tiny-usb, a simple do-it-yourself USB to I2C interface. See |
| http://www.harbaum.org/till/i2c_tiny_usb for hardware details. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-tiny-usb. |
| |
| config I2C_VIPERBOARD |
| tristate "Viperboard I2C master support" |
| depends on MFD_VIPERBOARD && USB |
| help |
| Say yes here to access the I2C part of the Nano River |
| Technologies Viperboard as I2C master. |
| See viperboard API specification and Nano |
| River Tech's viperboard.h for detailed meaning |
| of the module parameters. |
| |
| comment "Other I2C/SMBus bus drivers" |
| |
| config I2C_ACORN |
| tristate "Acorn IOC/IOMD I2C bus support" |
| depends on ARCH_ACORN |
| default y |
| select I2C_ALGOBIT |
| help |
| Say yes if you want to support the I2C bus on Acorn platforms. |
| |
| If you don't know, say Y. |
| |
| config I2C_ELEKTOR |
| tristate "Elektor ISA card" |
| depends on ISA && HAS_IOPORT_MAP && BROKEN_ON_SMP |
| select I2C_ALGOPCF |
| help |
| This supports the PCF8584 ISA bus I2C adapter. Say Y if you own |
| such an adapter. |
| |
| This support is also available as a module. If so, the module |
| will be called i2c-elektor. |
| |
| config I2C_PCA_ISA |
| tristate "PCA9564/PCA9665 on an ISA bus" |
| depends on ISA |
| select I2C_ALGOPCA |
| default n |
| help |
| This driver supports ISA boards using the Philips PCA9564/PCA9665 |
| parallel bus to I2C bus controller. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-pca-isa. |
| |
| This device is almost undetectable and using this driver on a |
| system which doesn't have this device will result in long |
| delays when I2C/SMBus chip drivers are loaded (e.g. at boot |
| time). If unsure, say N. |
| |
| config I2C_SIBYTE |
| tristate "SiByte SMBus interface" |
| depends on SIBYTE_SB1xxx_SOC |
| help |
| Supports the SiByte SOC on-chip I2C interfaces (2 channels). |
| |
| config I2C_CROS_EC_TUNNEL |
| tristate "ChromeOS EC tunnel I2C bus" |
| depends on MFD_CROS_EC |
| help |
| If you say yes here you get an I2C bus that will tunnel i2c commands |
| through to the other side of the ChromeOS EC to the i2c bus |
| connected there. This will work whatever the interface used to |
| talk to the EC (SPI, I2C or LPC). |
| |
| config I2C_XGENE_SLIMPRO |
| tristate "APM X-Gene SoC I2C SLIMpro devices support" |
| depends on ARCH_XGENE && MAILBOX |
| help |
| Enable I2C bus access using the APM X-Gene SoC SLIMpro |
| co-processor. The I2C device access the I2C bus via the X-Gene |
| to SLIMpro (On chip coprocessor) mailbox mechanism. |
| If unsure, say N. |
| |
| config SCx200_ACB |
| tristate "Geode ACCESS.bus support" |
| depends on X86_32 && PCI |
| help |
| Enable the use of the ACCESS.bus controllers on the Geode SCx200 and |
| SC1100 processors and the CS5535 and CS5536 Geode companion devices. |
| |
| If you don't know what to do here, say N. |
| |
| This support is also available as a module. If so, the module |
| will be called scx200_acb. |
| |
| config I2C_OPAL |
| tristate "IBM OPAL I2C driver" |
| depends on PPC_POWERNV |
| default y |
| help |
| This exposes the PowerNV platform i2c busses to the linux i2c layer, |
| the driver is based on the OPAL interfaces. |
| |
| This driver can also be built as a module. If so, the module will be |
| called as i2c-opal. |
| |
| endmenu |