| #ifndef MFD_TMIO_H |
| #define MFD_TMIO_H |
| |
| #include <linux/device.h> |
| #include <linux/fb.h> |
| #include <linux/io.h> |
| #include <linux/jiffies.h> |
| #include <linux/mmc/card.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| |
| #define tmio_ioread8(addr) readb(addr) |
| #define tmio_ioread16(addr) readw(addr) |
| #define tmio_ioread16_rep(r, b, l) readsw(r, b, l) |
| #define tmio_ioread32(addr) \ |
| (((u32) readw((addr))) | (((u32) readw((addr) + 2)) << 16)) |
| |
| #define tmio_iowrite8(val, addr) writeb((val), (addr)) |
| #define tmio_iowrite16(val, addr) writew((val), (addr)) |
| #define tmio_iowrite16_rep(r, b, l) writesw(r, b, l) |
| #define tmio_iowrite32(val, addr) \ |
| do { \ |
| writew((val), (addr)); \ |
| writew((val) >> 16, (addr) + 2); \ |
| } while (0) |
| |
| #define CNF_CMD 0x04 |
| #define CNF_CTL_BASE 0x10 |
| #define CNF_INT_PIN 0x3d |
| #define CNF_STOP_CLK_CTL 0x40 |
| #define CNF_GCLK_CTL 0x41 |
| #define CNF_SD_CLK_MODE 0x42 |
| #define CNF_PIN_STATUS 0x44 |
| #define CNF_PWR_CTL_1 0x48 |
| #define CNF_PWR_CTL_2 0x49 |
| #define CNF_PWR_CTL_3 0x4a |
| #define CNF_CARD_DETECT_MODE 0x4c |
| #define CNF_SD_SLOT 0x50 |
| #define CNF_EXT_GCLK_CTL_1 0xf0 |
| #define CNF_EXT_GCLK_CTL_2 0xf1 |
| #define CNF_EXT_GCLK_CTL_3 0xf9 |
| #define CNF_SD_LED_EN_1 0xfa |
| #define CNF_SD_LED_EN_2 0xfe |
| |
| #define SDCREN 0x2 /* Enable access to MMC CTL regs. (flag in COMMAND_REG)*/ |
| |
| #define sd_config_write8(base, shift, reg, val) \ |
| tmio_iowrite8((val), (base) + ((reg) << (shift))) |
| #define sd_config_write16(base, shift, reg, val) \ |
| tmio_iowrite16((val), (base) + ((reg) << (shift))) |
| #define sd_config_write32(base, shift, reg, val) \ |
| do { \ |
| tmio_iowrite16((val), (base) + ((reg) << (shift))); \ |
| tmio_iowrite16((val) >> 16, (base) + ((reg + 2) << (shift))); \ |
| } while (0) |
| |
| /* tmio MMC platform flags */ |
| #define TMIO_MMC_WRPROTECT_DISABLE (1 << 0) |
| /* |
| * Some controllers can support a 2-byte block size when the bus width |
| * is configured in 4-bit mode. |
| */ |
| #define TMIO_MMC_BLKSZ_2BYTES (1 << 1) |
| /* |
| * Some controllers can support SDIO IRQ signalling. |
| */ |
| #define TMIO_MMC_SDIO_IRQ (1 << 2) |
| |
| /* Some controllers don't need to wait 10ms for clock changes */ |
| #define TMIO_MMC_FAST_CLK_CHG (1 << 3) |
| |
| /* |
| * Some controllers require waiting for the SD bus to become |
| * idle before writing to some registers. |
| */ |
| #define TMIO_MMC_HAS_IDLE_WAIT (1 << 4) |
| /* |
| * A GPIO is used for card hotplug detection. We need an extra flag for this, |
| * because 0 is a valid GPIO number too, and requiring users to specify |
| * cd_gpio < 0 to disable GPIO hotplug would break backwards compatibility. |
| */ |
| #define TMIO_MMC_USE_GPIO_CD (1 << 5) |
| |
| /* |
| * Some controllers doesn't have over 0x100 register. |
| * it is used to checking accessibility of |
| * CTL_SD_CARD_CLK_CTL / CTL_CLK_AND_WAIT_CTL |
| */ |
| #define TMIO_MMC_HAVE_HIGH_REG (1 << 6) |
| |
| /* |
| * Some controllers have CMD12 automatically |
| * issue/non-issue register |
| */ |
| #define TMIO_MMC_HAVE_CMD12_CTRL (1 << 7) |
| |
| /* |
| * Some controllers needs to set 1 on SDIO status reserved bits |
| */ |
| #define TMIO_MMC_SDIO_STATUS_QUIRK (1 << 8) |
| |
| /* |
| * Some controllers allows to set SDx actual clock |
| */ |
| #define TMIO_MMC_CLK_ACTUAL (1 << 10) |
| |
| int tmio_core_mmc_enable(void __iomem *cnf, int shift, unsigned long base); |
| int tmio_core_mmc_resume(void __iomem *cnf, int shift, unsigned long base); |
| void tmio_core_mmc_pwr(void __iomem *cnf, int shift, int state); |
| void tmio_core_mmc_clk_div(void __iomem *cnf, int shift, int state); |
| |
| struct dma_chan; |
| |
| /* |
| * data for the MMC controller |
| */ |
| struct tmio_mmc_data { |
| void *chan_priv_tx; |
| void *chan_priv_rx; |
| unsigned int hclk; |
| unsigned long capabilities; |
| unsigned long capabilities2; |
| unsigned long flags; |
| u32 ocr_mask; /* available voltages */ |
| unsigned int cd_gpio; |
| int alignment_shift; |
| dma_addr_t dma_rx_offset; |
| void (*set_pwr)(struct platform_device *host, int state); |
| void (*set_clk_div)(struct platform_device *host, int state); |
| }; |
| |
| /* |
| * data for the NAND controller |
| */ |
| struct tmio_nand_data { |
| struct nand_bbt_descr *badblock_pattern; |
| struct mtd_partition *partition; |
| unsigned int num_partitions; |
| }; |
| |
| #define FBIO_TMIO_ACC_WRITE 0x7C639300 |
| #define FBIO_TMIO_ACC_SYNC 0x7C639301 |
| |
| struct tmio_fb_data { |
| int (*lcd_set_power)(struct platform_device *fb_dev, |
| bool on); |
| int (*lcd_mode)(struct platform_device *fb_dev, |
| const struct fb_videomode *mode); |
| int num_modes; |
| struct fb_videomode *modes; |
| |
| /* in mm: size of screen */ |
| int height; |
| int width; |
| }; |
| |
| |
| #endif |