drivers/usb/host/sl811.h - kernel/msm-4.9 - Gitiles

 /*
  * SL811HS register declarations and HCD data structures
  *
  * Copyright (C) 2004 Psion Teklogix
  * Copyright (C) 2004 David Brownell
  * Copyright (C) 2001 Cypress Semiconductor Inc.
  */

 /*
  * SL811HS has transfer registers, and control registers.  In host/master
  * mode one set of registers is used; in peripheral/slave mode, another.
  *  - SL11H only has some "A" transfer registers from 0x00-0x04
  *  - SL811HS also has "B" registers from 0x08-0x0c
  *  - SL811S (or HS in slave mode) has four A+B sets, at 00, 10, 20, 30
  */

 #define SL811_EP_A(base)	((base) + 0)
 #define SL811_EP_B(base)	((base) + 8)

 #define SL811_HOST_BUF		0x00
 #define SL811_PERIPH_EP0	0x00
 #define SL811_PERIPH_EP1	0x10
 #define SL811_PERIPH_EP2	0x20
 #define SL811_PERIPH_EP3	0x30


 /* TRANSFER REGISTERS:  host and peripheral sides are similar
  * except for the control models (master vs slave).
  */
 #define SL11H_HOSTCTLREG	0
 #	define SL11H_HCTLMASK_ARM	0x01
 #	define SL11H_HCTLMASK_ENABLE	0x02
 #	define SL11H_HCTLMASK_IN	0x00
 #	define SL11H_HCTLMASK_OUT	0x04
 #	define SL11H_HCTLMASK_ISOCH	0x10
 #	define SL11H_HCTLMASK_AFTERSOF	0x20
 #	define SL11H_HCTLMASK_TOGGLE	0x40
 #	define SL11H_HCTLMASK_PREAMBLE	0x80
 #define SL11H_BUFADDRREG	1
 #define SL11H_BUFLNTHREG	2
 #define SL11H_PKTSTATREG	3	/* read */
 #	define SL11H_STATMASK_ACK	0x01
 #	define SL11H_STATMASK_ERROR	0x02
 #	define SL11H_STATMASK_TMOUT	0x04
 #	define SL11H_STATMASK_SEQ	0x08
 #	define SL11H_STATMASK_SETUP	0x10
 #	define SL11H_STATMASK_OVF	0x20
 #	define SL11H_STATMASK_NAK	0x40
 #	define SL11H_STATMASK_STALL	0x80
 #define SL11H_PIDEPREG		3	/* write */
 #	define	SL_SETUP	0xd0
 #	define	SL_IN		0x90
 #	define	SL_OUT		0x10
 #	define	SL_SOF		0x50
 #	define	SL_PREAMBLE	0xc0
 #	define	SL_NAK		0xa0
 #	define	SL_STALL	0xe0
 #	define	SL_DATA0	0x30
 #	define	SL_DATA1	0xb0
 #define SL11H_XFERCNTREG	4	/* read */
 #define SL11H_DEVADDRREG	4	/* write */


 /* CONTROL REGISTERS:  host and peripheral are very different.
  */
 #define SL11H_CTLREG1		5
 #	define SL11H_CTL1MASK_SOF_ENA	0x01
 #	define SL11H_CTL1MASK_FORCE	0x18
 #		define SL11H_CTL1MASK_NORMAL	0x00
 #		define SL11H_CTL1MASK_SE0	0x08	/* reset */
 #		define SL11H_CTL1MASK_J		0x10
 #		define SL11H_CTL1MASK_K		0x18	/* resume */
 #	define SL11H_CTL1MASK_LSPD	0x20
 #	define SL11H_CTL1MASK_SUSPEND	0x40
 #define SL11H_IRQ_ENABLE	6
 #	define SL11H_INTMASK_DONE_A	0x01
 #	define SL11H_INTMASK_DONE_B	0x02
 #	define SL11H_INTMASK_SOFINTR	0x10
 #	define SL11H_INTMASK_INSRMV	0x20	/* to/from SE0 */
 #	define SL11H_INTMASK_RD		0x40
 #	define SL11H_INTMASK_DP		0x80	/* only in INTSTATREG */
 #define SL11S_ADDRESS		7

 /* 0x08-0x0c are for the B buffer (not in SL11) */

 #define SL11H_IRQ_STATUS	0x0D	/* write to ack */
 #define SL11H_HWREVREG		0x0E	/* read */
 #	define SL11H_HWRMASK_HWREV	0xF0
 #define SL11H_SOFLOWREG		0x0E	/* write */
 #define SL11H_SOFTMRREG		0x0F	/* read */

 /* a write to this register enables SL811HS features.
  * HOST flag presumably overrides the chip input signal?
  */
 #define SL811HS_CTLREG2		0x0F
 #	define SL811HS_CTL2MASK_SOF_MASK	0x3F
 #	define SL811HS_CTL2MASK_DSWAP		0x40
 #	define SL811HS_CTL2MASK_HOST		0x80

 #define SL811HS_CTL2_INIT	(SL811HS_CTL2MASK_HOST | 0x2e)


 /* DATA BUFFERS: registers from 0x10..0xff are for data buffers;
  * that's 240 bytes, which we'll split evenly between A and B sides.
  * Only ISO can use more than 64 bytes per packet.
  * (The SL11S has 0x40..0xff for buffers.)
  */
 #define H_MAXPACKET	120		/* bytes in A or B fifos */

 #define SL11H_DATA_START	0x10
 #define	SL811HS_PACKET_BUF(is_a)	((is_a) \
 		? SL11H_DATA_START \
 		: (SL11H_DATA_START + H_MAXPACKET))

 /*-------------------------------------------------------------------------*/

 #define	LOG2_PERIODIC_SIZE	5	/* arbitrary; this matches OHCI */
 #define	PERIODIC_SIZE		(1 << LOG2_PERIODIC_SIZE)

 struct sl811 {
 	spinlock_t		lock;
 	void __iomem		*addr_reg;
 	void __iomem		*data_reg;
 	struct sl811_platform_data	*board;
 	struct dentry 		*debug_file;

 	unsigned long		stat_insrmv;
 	unsigned long		stat_wake;
 	unsigned long		stat_sof;
 	unsigned long		stat_a;
 	unsigned long		stat_b;
 	unsigned long		stat_lost;
 	unsigned long		stat_overrun;

 	/* sw model */
 	struct timer_list	timer;
 	struct sl811h_ep	*next_periodic;
 	struct sl811h_ep	*next_async;

 	struct sl811h_ep	*active_a;
 	unsigned long		jiffies_a;
 	struct sl811h_ep	*active_b;
 	unsigned long		jiffies_b;

 	u32			port1;
 	u8			ctrl1, ctrl2, irq_enable;
 	u16			frame;

 	/* async schedule: control, bulk */
 	struct list_head	async;

 	/* periodic schedule: interrupt, iso */
 	u16			load[PERIODIC_SIZE];
 	struct sl811h_ep	*periodic[PERIODIC_SIZE];
 	unsigned		periodic_count;
 };

 static inline struct sl811 *hcd_to_sl811(struct usb_hcd *hcd)
 {
 	return (struct sl811 *) (hcd->hcd_priv);
 }

 static inline struct usb_hcd *sl811_to_hcd(struct sl811 *sl811)
 {
 	return container_of((void *) sl811, struct usb_hcd, hcd_priv);
 }

 struct sl811h_ep {
 	struct usb_host_endpoint *hep;
 	struct usb_device	*udev;

 	u8			defctrl;
 	u8			maxpacket;
 	u8			epnum;
 	u8			nextpid;

 	u16			error_count;
 	u16			nak_count;
 	u16			length;		/* of current packet */

 	/* periodic schedule */
 	u16			period;
 	u16			branch;
 	u16			load;
 	struct sl811h_ep	*next;

 	/* async schedule */
 	struct list_head	schedule;
 };

 /*-------------------------------------------------------------------------*/

 /* These register utilities should work for the SL811S register API too
  * NOTE:  caller must hold sl811->lock.
  */

 static inline u8 sl811_read(struct sl811 *sl811, int reg)
 {
 	writeb(reg, sl811->addr_reg);
 	return readb(sl811->data_reg);
 }

 static inline void sl811_write(struct sl811 *sl811, int reg, u8 val)
 {
 	writeb(reg, sl811->addr_reg);
 	writeb(val, sl811->data_reg);
 }

 static inline void
 sl811_write_buf(struct sl811 *sl811, int addr, const void *buf, size_t count)
 {
 	const u8	*data;
 	void __iomem	*data_reg;

 	if (!count)
 		return;
 	writeb(addr, sl811->addr_reg);

 	data = buf;
 	data_reg = sl811->data_reg;
 	do {
 		writeb(*data++, data_reg);
 	} while (--count);
 }

 static inline void
 sl811_read_buf(struct sl811 *sl811, int addr, void *buf, size_t count)
 {
 	u8 		*data;
 	void __iomem	*data_reg;

 	if (!count)
 		return;
 	writeb(addr, sl811->addr_reg);

 	data = buf;
 	data_reg = sl811->data_reg;
 	do {
 		*data++ = readb(data_reg);
 	} while (--count);
 }

 /*-------------------------------------------------------------------------*/

 #ifdef PACKET_TRACE
 #    define PACKET		pr_debug("sl811: "stuff)
 #else
 #    define PACKET(stuff...)	do{}while(0)
 #endif
	/*
	* SL811HS register declarations and HCD data structures
	*
	* Copyright (C) 2004 Psion Teklogix
	* Copyright (C) 2004 David Brownell
	* Copyright (C) 2001 Cypress Semiconductor Inc.
	*/

	/*
	* SL811HS has transfer registers, and control registers. In host/master
	* mode one set of registers is used; in peripheral/slave mode, another.
	* - SL11H only has some "A" transfer registers from 0x00-0x04
	* - SL811HS also has "B" registers from 0x08-0x0c
	* - SL811S (or HS in slave mode) has four A+B sets, at 00, 10, 20, 30
	*/

	#define SL811_EP_A(base) ((base) + 0)
	#define SL811_EP_B(base) ((base) + 8)

	#define SL811_HOST_BUF 0x00
	#define SL811_PERIPH_EP0 0x00
	#define SL811_PERIPH_EP1 0x10
	#define SL811_PERIPH_EP2 0x20
	#define SL811_PERIPH_EP3 0x30


	/* TRANSFER REGISTERS: host and peripheral sides are similar
	* except for the control models (master vs slave).
	*/
	#define SL11H_HOSTCTLREG 0
	# define SL11H_HCTLMASK_ARM 0x01
	# define SL11H_HCTLMASK_ENABLE 0x02
	# define SL11H_HCTLMASK_IN 0x00
	# define SL11H_HCTLMASK_OUT 0x04
	# define SL11H_HCTLMASK_ISOCH 0x10
	# define SL11H_HCTLMASK_AFTERSOF 0x20
	# define SL11H_HCTLMASK_TOGGLE 0x40
	# define SL11H_HCTLMASK_PREAMBLE 0x80
	#define SL11H_BUFADDRREG 1
	#define SL11H_BUFLNTHREG 2
	#define SL11H_PKTSTATREG 3 /* read */
	# define SL11H_STATMASK_ACK 0x01
	# define SL11H_STATMASK_ERROR 0x02
	# define SL11H_STATMASK_TMOUT 0x04
	# define SL11H_STATMASK_SEQ 0x08
	# define SL11H_STATMASK_SETUP 0x10
	# define SL11H_STATMASK_OVF 0x20
	# define SL11H_STATMASK_NAK 0x40
	# define SL11H_STATMASK_STALL 0x80
	#define SL11H_PIDEPREG 3 /* write */
	# define SL_SETUP 0xd0
	# define SL_IN 0x90
	# define SL_OUT 0x10
	# define SL_SOF 0x50
	# define SL_PREAMBLE 0xc0
	# define SL_NAK 0xa0
	# define SL_STALL 0xe0
	# define SL_DATA0 0x30
	# define SL_DATA1 0xb0
	#define SL11H_XFERCNTREG 4 /* read */
	#define SL11H_DEVADDRREG 4 /* write */


	/* CONTROL REGISTERS: host and peripheral are very different.
	*/
	#define SL11H_CTLREG1 5
	# define SL11H_CTL1MASK_SOF_ENA 0x01
	# define SL11H_CTL1MASK_FORCE 0x18
	# define SL11H_CTL1MASK_NORMAL 0x00
	# define SL11H_CTL1MASK_SE0 0x08 /* reset */
	# define SL11H_CTL1MASK_J 0x10
	# define SL11H_CTL1MASK_K 0x18 /* resume */
	# define SL11H_CTL1MASK_LSPD 0x20
	# define SL11H_CTL1MASK_SUSPEND 0x40
	#define SL11H_IRQ_ENABLE 6
	# define SL11H_INTMASK_DONE_A 0x01
	# define SL11H_INTMASK_DONE_B 0x02
	# define SL11H_INTMASK_SOFINTR 0x10
	# define SL11H_INTMASK_INSRMV 0x20 /* to/from SE0 */
	# define SL11H_INTMASK_RD 0x40
	# define SL11H_INTMASK_DP 0x80 /* only in INTSTATREG */
	#define SL11S_ADDRESS 7

	/* 0x08-0x0c are for the B buffer (not in SL11) */

	#define SL11H_IRQ_STATUS 0x0D /* write to ack */
	#define SL11H_HWREVREG 0x0E /* read */
	# define SL11H_HWRMASK_HWREV 0xF0
	#define SL11H_SOFLOWREG 0x0E /* write */
	#define SL11H_SOFTMRREG 0x0F /* read */

	/* a write to this register enables SL811HS features.
	* HOST flag presumably overrides the chip input signal?
	*/
	#define SL811HS_CTLREG2 0x0F
	# define SL811HS_CTL2MASK_SOF_MASK 0x3F
	# define SL811HS_CTL2MASK_DSWAP 0x40
	# define SL811HS_CTL2MASK_HOST 0x80

	#define SL811HS_CTL2_INIT (SL811HS_CTL2MASK_HOST \| 0x2e)


	/* DATA BUFFERS: registers from 0x10..0xff are for data buffers;
	* that's 240 bytes, which we'll split evenly between A and B sides.
	* Only ISO can use more than 64 bytes per packet.
	* (The SL11S has 0x40..0xff for buffers.)
	*/
	#define H_MAXPACKET 120 /* bytes in A or B fifos */

	#define SL11H_DATA_START 0x10
	#define SL811HS_PACKET_BUF(is_a) ((is_a) \
	? SL11H_DATA_START \
	: (SL11H_DATA_START + H_MAXPACKET))

	/-------------------------------------------------------------------------/

	#define LOG2_PERIODIC_SIZE 5 /* arbitrary; this matches OHCI */
	#define PERIODIC_SIZE (1 << LOG2_PERIODIC_SIZE)

	struct sl811 {
	spinlock_t lock;
	void __iomem *addr_reg;
	void __iomem *data_reg;
	struct sl811_platform_data *board;
	struct dentry *debug_file;

	unsigned long stat_insrmv;
	unsigned long stat_wake;
	unsigned long stat_sof;
	unsigned long stat_a;
	unsigned long stat_b;
	unsigned long stat_lost;
	unsigned long stat_overrun;

	/* sw model */
	struct timer_list timer;
	struct sl811h_ep *next_periodic;
	struct sl811h_ep *next_async;

	struct sl811h_ep *active_a;
	unsigned long jiffies_a;
	struct sl811h_ep *active_b;
	unsigned long jiffies_b;

	u32 port1;
	u8 ctrl1, ctrl2, irq_enable;
	u16 frame;

	/* async schedule: control, bulk */
	struct list_head async;

	/* periodic schedule: interrupt, iso */
	u16 load[PERIODIC_SIZE];
	struct sl811h_ep *periodic[PERIODIC_SIZE];
	unsigned periodic_count;
	};

	static inline struct sl811 hcd_to_sl811(struct usb_hcd hcd)
	{
	return (struct sl811 *) (hcd->hcd_priv);
	}

	static inline struct usb_hcd sl811_to_hcd(struct sl811 sl811)
	{
	return container_of((void *) sl811, struct usb_hcd, hcd_priv);
	}

	struct sl811h_ep {
	struct usb_host_endpoint *hep;
	struct usb_device *udev;

	u8 defctrl;
	u8 maxpacket;
	u8 epnum;
	u8 nextpid;

	u16 error_count;
	u16 nak_count;
	u16 length; /* of current packet */

	/* periodic schedule */
	u16 period;
	u16 branch;
	u16 load;
	struct sl811h_ep *next;

	/* async schedule */
	struct list_head schedule;
	};

	/-------------------------------------------------------------------------/

	/* These register utilities should work for the SL811S register API too
	* NOTE: caller must hold sl811->lock.
	*/

	static inline u8 sl811_read(struct sl811 *sl811, int reg)
	{
	writeb(reg, sl811->addr_reg);
	return readb(sl811->data_reg);
	}

	static inline void sl811_write(struct sl811 *sl811, int reg, u8 val)
	{
	writeb(reg, sl811->addr_reg);
	writeb(val, sl811->data_reg);
	}

	static inline void
	sl811_write_buf(struct sl811 sl811, int addr, const void buf, size_t count)
	{
	const u8 *data;
	void __iomem *data_reg;

	if (!count)
	return;
	writeb(addr, sl811->addr_reg);

	data = buf;
	data_reg = sl811->data_reg;
	do {
	writeb(*data++, data_reg);
	} while (--count);
	}

	static inline void
	sl811_read_buf(struct sl811 sl811, int addr, void buf, size_t count)
	{
	u8 *data;
	void __iomem *data_reg;

	if (!count)
	return;
	writeb(addr, sl811->addr_reg);

	data = buf;
	data_reg = sl811->data_reg;
	do {
	*data++ = readb(data_reg);
	} while (--count);
	}

	/-------------------------------------------------------------------------/

	#ifdef PACKET_TRACE
	# define PACKET pr_debug("sl811: "stuff)
	#else
	# define PACKET(stuff...) do{}while(0)
	#endif