| FMC Device |
| ********** |
| |
| Within the Linux bus framework, the FMC device is created and |
| registered by the carrier driver. For example, the PCI driver for the |
| SPEC card fills a data structure for each SPEC that it drives, and |
| registers an associated FMC device for each card. The SVEC driver can |
| do exactly the same for the VME carrier (actually, it should do it |
| twice, because the SVEC carries two FMC mezzanines). Similarly, an |
| Etherbone driver will be able to register its own FMC devices, offering |
| communication primitives through frame exchange. |
| |
| The contents of the EEPROM within the FMC are used for identification |
| purposes, i.e. for matching the device with its own driver. For this |
| reason the device structure includes a complete copy of the EEPROM |
| (actually, the carrier driver may choose whether or not to return it - |
| for example we most likely won't have the whole EEPROM available for |
| Etherbone devices. |
| |
| The following listing shows the current structure defining a device. |
| Please note that all the machinery is in place but some details may |
| still change in the future. For this reason, there is a version field |
| at the beginning of the structure. As usual, the minor number will |
| change for compatible changes (like a new flag) and the major number |
| will increase when an incompatible change happens (for example, a |
| change in layout of some fmc data structures). Device writers should |
| just set it to the value FMC_VERSION, and be ready to get back -EINVAL |
| at registration time. |
| |
| struct fmc_device { |
| unsigned long version; |
| unsigned long flags; |
| struct module *owner; /* char device must pin it */ |
| struct fmc_fru_id id; /* for EEPROM-based match */ |
| struct fmc_operations *op; /* carrier-provided */ |
| int irq; /* according to host bus. 0 == none */ |
| int eeprom_len; /* Usually 8kB, may be less */ |
| int eeprom_addr; /* 0x50, 0x52 etc */ |
| uint8_t *eeprom; /* Full contents or leading part */ |
| char *carrier_name; /* "SPEC" or similar, for special use */ |
| void *carrier_data; /* "struct spec *" or equivalent */ |
| __iomem void *fpga_base; /* May be NULL (Etherbone) */ |
| __iomem void *slot_base; /* Set by the driver */ |
| struct fmc_device **devarray; /* Allocated by the bus */ |
| int slot_id; /* Index in the slot array */ |
| int nr_slots; /* Number of slots in this carrier */ |
| unsigned long memlen; /* Used for the char device */ |
| struct device dev; /* For Linux use */ |
| struct device *hwdev; /* The underlying hardware device */ |
| unsigned long sdbfs_entry; |
| struct sdb_array *sdb; |
| uint32_t device_id; /* Filled by the device */ |
| char *mezzanine_name; /* Defaults to ``fmc'' */ |
| void *mezzanine_data; |
| }; |
| |
| The meaning of most fields is summarized in the code comment above. |
| |
| The following fields must be filled by the carrier driver before |
| registration: |
| |
| * version: must be set to FMC_VERSION. |
| |
| * owner: set to MODULE_OWNER. |
| |
| * op: the operations to act on the device. |
| |
| * irq: number for the mezzanine; may be zero. |
| |
| * eeprom_len: length of the following array. |
| |
| * eeprom_addr: 0x50 for first mezzanine and so on. |
| |
| * eeprom: the full content of the I2C EEPROM. |
| |
| * carrier_name. |
| |
| * carrier_data: a unique pointer for the carrier. |
| |
| * fpga_base: the I/O memory address (may be NULL). |
| |
| * slot_id: the index of this slot (starting from zero). |
| |
| * memlen: if fpga_base is valid, the length of I/O memory. |
| |
| * hwdev: to be used in some dev_err() calls. |
| |
| * device_id: a slot-specific unique integer number. |
| |
| |
| Please note that the carrier should read its own EEPROM memory before |
| registering the device, as well as fill all other fields listed above. |
| |
| The following fields should not be assigned, because they are filled |
| later by either the bus or the device driver: |
| |
| * flags. |
| |
| * fru_id: filled by the bus, parsing the eeprom. |
| |
| * slot_base: filled and used by the driver, if useful to it. |
| |
| * devarray: an array og all mezzanines driven by a singe FPGA. |
| |
| * nr_slots: set by the core at registration time. |
| |
| * dev: used by Linux. |
| |
| * sdb: FPGA contents, scanned according to driver's directions. |
| |
| * sdbfs_entry: SDB entry point in EEPROM: autodetected. |
| |
| * mezzanine_data: available for the driver. |
| |
| * mezzanine_name: filled by fmc-bus during identification. |
| |
| |
| Note: mezzanine_data may be redundant, because Linux offers the drvdata |
| approach, so the field may be removed in later versions of this bus |
| implementation. |
| |
| As I write this, she SPEC carrier is already completely functional in |
| the fmc-bus environment, and is a good reference to look at. |
| |
| |
| The API Offered by Carriers |
| =========================== |
| |
| The carrier provides a number of methods by means of the |
| `fmc_operations' structure, which currently is defined like this |
| (again, it is a moving target, please refer to the header rather than |
| this document): |
| |
| struct fmc_operations { |
| uint32_t (*readl)(struct fmc_device *fmc, int offset); |
| void (*writel)(struct fmc_device *fmc, uint32_t value, int offset); |
| int (*reprogram)(struct fmc_device *f, struct fmc_driver *d, char *gw); |
| int (*validate)(struct fmc_device *fmc, struct fmc_driver *drv); |
| int (*irq_request)(struct fmc_device *fmc, irq_handler_t h, |
| char *name, int flags); |
| void (*irq_ack)(struct fmc_device *fmc); |
| int (*irq_free)(struct fmc_device *fmc); |
| int (*gpio_config)(struct fmc_device *fmc, struct fmc_gpio *gpio, |
| int ngpio); |
| int (*read_ee)(struct fmc_device *fmc, int pos, void *d, int l); |
| int (*write_ee)(struct fmc_device *fmc, int pos, const void *d, int l); |
| }; |
| |
| The individual methods perform the following tasks: |
| |
| `readl' |
| `writel' |
| These functions access FPGA registers by whatever means the |
| carrier offers. They are not expected to fail, and most of the time |
| they will just make a memory access to the host bus. If the |
| carrier provides a fpga_base pointer, the driver may use direct |
| access through that pointer. For this reason the header offers the |
| inline functions fmc_readl and fmc_writel that access fpga_base if |
| the respective method is NULL. A driver that wants to be portable |
| and efficient should use fmc_readl and fmc_writel. For Etherbone, |
| or other non-local carriers, error-management is still to be |
| defined. |
| |
| `validate' |
| Module parameters are used to manage different applications for |
| two or more boards of the same kind. Validation is based on the |
| busid module parameter, if provided, and returns the matching |
| index in the associated array. See *note Module Parameters:: in in |
| doubt. If no match is found, `-ENOENT' is returned; if the user |
| didn't pass `busid=', all devices will pass validation. The value |
| returned by the validate method can be used as index into other |
| parameters (for example, some drivers use the `lm32=' parameter in |
| this way). Such "generic parameters" are documented in *note |
| Module Parameters::, below. The validate method is used by |
| `fmc-trivial.ko', described in *note fmc-trivial::. |
| |
| `reprogram' |
| The carrier enumerates FMC devices by loading a standard (or |
| golden) FPGA binary that allows EEPROM access. Each driver, then, |
| will need to reprogram the FPGA by calling this function. If the |
| name argument is NULL, the carrier should reprogram the golden |
| binary. If the gateware name has been overridden through module |
| parameters (in a carrier-specific way) the file loaded will match |
| the parameters. Per-device gateware names can be specified using |
| the `gateware=' parameter, see *note Module Parameters::. Note: |
| Clients should call rhe new helper, fmc_reprogram, which both |
| calls this method and parse the SDB tree of the FPGA. |
| |
| `irq_request' |
| `irq_ack' |
| `irq_free' |
| Interrupt management is carrier-specific, so it is abstracted as |
| operations. The interrupt number is listed in the device |
| structure, and for the mezzanine driver the number is only |
| informative. The handler will receive the fmc pointer as dev_id; |
| the flags argument is passed to the Linux request_irq function, |
| but fmc-specific flags may be added in the future. You'll most |
| likely want to pass the `IRQF_SHARED' flag. |
| |
| `gpio_config' |
| The method allows to configure a GPIO pin in the carrier, and read |
| its current value if it is configured as input. See *note The GPIO |
| Abstraction:: for details. |
| |
| `read_ee' |
| `write_ee' |
| Read or write the EEPROM. The functions are expected to be only |
| called before reprogramming and the carrier should refuse them |
| with `ENODEV' after reprogramming. The offset is expected to be |
| within 8kB (the current size), but addresses up to 1MB are |
| reserved to fit bigger I2C devices in the future. Carriers may |
| offer access to other internal flash memories using these same |
| methods: for example the SPEC driver may define that its carrier |
| I2C memory is seen at offset 1M and the internal SPI flash is seen |
| at offset 16M. This multiplexing of several flash memories in the |
| same address space is is carrier-specific and should only be used |
| by a driver that has verified the `carrier_name' field. |
| |
| |
| |
| The GPIO Abstraction |
| ==================== |
| |
| Support for GPIO pins in the fmc-bus environment is not very |
| straightforward and deserves special discussion. |
| |
| While the general idea of a carrier-independent driver seems to fly, |
| configuration of specific signals within the carrier needs at least |
| some knowledge of the carrier itself. For this reason, the specific |
| driver can request to configure carrier-specific GPIO pins, numbered |
| from 0 to at most 4095. Configuration is performed by passing a |
| pointer to an array of struct fmc_gpio items, as well as the length of |
| the array. This is the data structure: |
| |
| struct fmc_gpio { |
| char *carrier_name; |
| int gpio; |
| int _gpio; /* internal use by the carrier */ |
| int mode; /* GPIOF_DIR_OUT etc, from <linux/gpio.h> */ |
| int irqmode; /* IRQF_TRIGGER_LOW and so on */ |
| }; |
| |
| By specifying a carrier_name for each pin, the driver may access |
| different pins in different carriers. The gpio_config method is |
| expected to return the number of pins successfully configured, ignoring |
| requests for other carriers. However, if no pin is configured (because |
| no structure at all refers to the current carrier_name), the operation |
| returns an error so the caller will know that it is running under a |
| yet-unsupported carrier. |
| |
| So, for example, a driver that has been developed and tested on both |
| the SPEC and the SVEC may request configuration of two different GPIO |
| pins, and expect one such configuration to succeed - if none succeeds |
| it most likely means that the current carrier is a still-unknown one. |
| |
| If, however, your GPIO pin has a specific known role, you can pass a |
| special number in the gpio field, using one of the following macros: |
| |
| #define FMC_GPIO_RAW(x) (x) /* 4096 of them */ |
| #define FMC_GPIO_IRQ(x) ((x) + 0x1000) /* 256 of them */ |
| #define FMC_GPIO_LED(x) ((x) + 0x1100) /* 256 of them */ |
| #define FMC_GPIO_KEY(x) ((x) + 0x1200) /* 256 of them */ |
| #define FMC_GPIO_TP(x) ((x) + 0x1300) /* 256 of them */ |
| #define FMC_GPIO_USER(x) ((x) + 0x1400) /* 256 of them */ |
| |
| Use of virtual GPIO numbers (anything but FMC_GPIO_RAW) is allowed |
| provided the carrier_name field in the data structure is left |
| unspecified (NULL). Each carrier is responsible for providing a mapping |
| between virtual and physical GPIO numbers. The carrier may then use the |
| _gpio field to cache the result of this mapping. |
| |
| All carriers must map their I/O lines to the sets above starting from |
| zero. The SPEC, for example, maps interrupt pins 0 and 1, and test |
| points 0 through 3 (even if the test points on the PCB are called |
| 5,6,7,8). |
| |
| If, for example, a driver requires a free LED and a test point (for a |
| scope probe to be plugged at some point during development) it may ask |
| for FMC_GPIO_LED(0) and FMC_GPIO_TP(0). Each carrier will provide |
| suitable GPIO pins. Clearly, the person running the drivers will know |
| the order used by the specific carrier driver in assigning leds and |
| testpoints, so to make a carrier-dependent use of the diagnostic tools. |
| |
| In theory, some form of autodetection should be possible: a driver like |
| the wr-nic (which uses IRQ(1) on the SPEC card) should configure |
| IRQ(0), make a test with software-generated interrupts and configure |
| IRQ(1) if the test fails. This probing step should be used because even |
| if the wr-nic gateware is known to use IRQ1 on the SPEC, the driver |
| should be carrier-independent and thus use IRQ(0) as a first bet - |
| actually, the knowledge that IRQ0 may fail is carrier-dependent |
| information, but using it doesn't make the driver unsuitable for other |
| carriers. |
| |
| The return value of gpio_config is defined as follows: |
| |
| * If no pin in the array can be used by the carrier, `-ENODEV'. |
| |
| * If at least one virtual GPIO number cannot be mapped, `-ENOENT'. |
| |
| * On success, 0 or positive. The value returned is the number of |
| high input bits (if no input is configured, the value for success |
| is 0). |
| |
| While I admit the procedure is not completely straightforward, it |
| allows configuration, input and output with a single carrier operation. |
| Given the typical use case of FMC devices, GPIO operations are not |
| expected to ever by in hot paths, and GPIO access so fare has only been |
| used to configure the interrupt pin, mode and polarity. Especially |
| reading inputs is not expected to be common. If your device has GPIO |
| capabilities in the hot path, you should consider using the kernel's |
| GPIO mechanisms. |