blob: 917c2d09e70c1550d1be0ea16d99c4a80111ae1d [file] [log] [blame]
Qualcomm technologies inc. Internet Packet Accelerator
Internet Packet Accelerator (IPA) is a programmable protocol
processor HW block. It is designed to support generic HW processing
of UL/DL IP packets for various use cases independent of radio technology.
Required properties:
IPA node:
- compatible : "qcom,ipa"
- reg: Specifies the base physical addresses and the sizes of the IPA
registers.
- reg-names: "ipa-base" - string to identify the IPA CORE base registers.
"bam-base" - string to identify the IPA BAM base registers.
"a2-bam-base" - string to identify the A2 BAM base registers.
- interrupts: Specifies the interrupt associated with IPA.
- interrupt-names: "ipa-irq" - string to identify the IPA core interrupt.
"bam-irq" - string to identify the IPA BAM interrupt.
"a2-bam-irq" - string to identify the A2 BAM interrupt.
- qcom,ipa-hw-ver: Specifies the IPA hardware version.
- qcom,ipa-ram-mmap: An array of unsigned integers representing addresses and
sizes which are used by the driver to access IPA RAM.
Optional:
- qcom,wan-rx-ring-size: size of WAN rx ring, default is 192
- qcom,lan-rx-ring-size: size of LAN rx ring, default is 192
- qcom,arm-smmu: SMMU is present and ARM SMMU driver is used
- qcom,msm-smmu: SMMU is present and QSMMU driver is used
- qcom,smmu-fast-map: Boolean context flag to set SMMU to fastpath mode
- ipa_smmu_ap: AP general purpose SMMU device
compatible "qcom,ipa-smmu-ap-cb"
- ipa_smmu_wlan: WDI SMMU device
compatible "qcom,ipa-smmu-wlan-cb"
- ipa_smmu_uc: uc SMMU device
compatible "qcom,ipa-smmu-uc-cb"
- qcom,use-a2-service: determine if A2 service will be used
- qcom,use-ipa-tethering-bridge: determine if tethering bridge will be used
- qcom,use-ipa-in-mhi-mode: Boolean context flag to indicate whether
device booting in MHI config or not.
- qcom,use-ipa-bamdma-a2-bridge: determine if a2/ipa hw bridge will be used
- qcom,ee: which EE is assigned to (non-secure) APPS from IPA-BAM POV. This
is a number
- qcom,ipa-hw-mode: IPA hardware mode - Normal, Virtual memory allocation,
memory allocation over a PCIe bridge
- qcom,msm-bus,name: String representing the client-name
- qcom,msm-bus,num-cases: Total number of usecases
- qcom,msm-bus,active-only: Boolean context flag for requests in active or
dual (active & sleep) contex
- qcom,msm-bus,num-paths: Total number of master-slave pairs
- qcom,msm-bus,vectors-KBps: Arrays of unsigned integers representing:
master-id, slave-id, arbitrated bandwidth
in KBps, instantaneous bandwidth in KBps
- qcom,ipa-bam-remote-mode: Boolean context flag to determine if ipa bam
is in remote mode.
- qcom,modem-cfg-emb-pipe-flt: Boolean context flag to determine if modem
configures embedded pipe filtering rules
- qcom,skip-uc-pipe-reset: Boolean context flag to indicate whether
a pipe reset via the IPA uC is required
- qcom,ipa-wdi2: Boolean context flag to indicate whether
using wdi-2.0 or not
- qcom,bandwidth-vote-for-ipa: Boolean context flag to indicate whether
ipa clock voting is done by bandwidth
voting via msm-bus-scale driver or not
- qcom,use-64-bit-dma-mask: Boolean context flag to indicate whether
using 64bit dma mask or not
- qcom,use-dma-zone: Boolean context flag to indicate whether memory
allocations controlled by IPA driver that do not
specify a struct device * should use GFP_DMA to
workaround IPA HW limitations
- qcom,use-rg10-limitation-mitigation: Boolean context flag to activate
the mitigation to register group 10
AP access limitation
- qcom,do-not-use-ch-gsi-20: Boolean context flag to activate
software workaround for IPA limitation
to not use GSI physical channel 20
- qcom,tethered-flow-control: Boolean context flag to indicate whether
apps based flow control is needed for tethered
call.
- qcom,rx-polling-sleep-ms: Receive Polling Timeout in millisecond,
default is 1 millisecond.
- qcom,ipa-polling-iteration: IPA Polling Iteration Count,default is 40.
- qcom,mhi-event-ring-id-limits: Two elements property. Start and End limits
for MHI event rings ids.
- qcom,ipa-tz-unlock-reg: Register start addresses and ranges which
need to be unlocked by TZ.
- qcom,ipa-uc-monitor-holb: Boolean context flag to indicate whether
monitoring of holb via IPA uc is required.
IPA pipe sub nodes (A2 static pipes configurations):
-label: two labels are supported, a2-to-ipa and ipa-to-a2 which
supply static configuration for A2-IPA connection.
-qcom,src-bam-physical-address: The physical address of the source BAM
-qcom,ipa-bam-mem-type:The memory type:
0(Pipe memory), 1(Private memory), 2(System memory)
-qcom,src-bam-pipe-index: Source pipe index
-qcom,dst-bam-physical-address: The physical address of the
destination BAM
-qcom,dst-bam-pipe-index: Destination pipe index
-qcom,data-fifo-offset: Data fifo base offset
-qcom,data-fifo-size: Data fifo size (bytes)
-qcom,descriptor-fifo-offset: Descriptor fifo base offset
-qcom,descriptor-fifo-size: Descriptor fifo size (bytes)
Optional properties:
-qcom,ipa-pipe-mem: Specifies the base physical address and the
size of the IPA pipe memory region.
Pipe memory is a feature which may be supported by the
target (HW platform). The Driver support using pipe
memory instead of system memory. In case this property
will not appear in the IPA DTS entry, the driver will
use system memory.
- clocks: This property shall provide a list of entries each of which
contains a phandle to clock controller device and a macro that is
the clock's name in hardware.This should be "clock_rpm" as clock
controller phandle and "clk_ipa_clk" as macro for "iface_clk"
- clock-names: This property shall contain the clock input names used
by driver in same order as the clocks property.This should be "iface_clk"
- emulator-bar0-offset: Specifies the offset, within PCIe BAR0, where
IPA/GSI programmable registers reside. This property is used only
with the IPA/GSI emulation system, which is connected to and
communicated with via PCIe.
IPA SMMU sub nodes
-compatible: "qcom,ipa-smmu-ap-cb" - represents the AP context bank.
-compatible: "qcom,ipa-smmu-wlan-cb" - represents IPA WLAN context bank.
-compatible: "qcom,ipa-smmu-uc-cb" - represents IPA uC context bank (for uC
offload scenarios).
- qcom,smmu-s1-bypass: Boolean context flag to set SMMU to S1 bypass.
- iommus : the phandle and stream IDs for the SMMU used by this root
- qcom,iova-mapping: specifies the start address and size of iova space.
- qcom,additional-mapping: specifies any addtional mapping needed for this
context bank. The format is <iova pa size>
- qcom,ipa-q6-smem-size: specifies the Q6 SMEM partition size
IPA SMP2P sub nodes
-compatible: "qcom,smp2pgpio-map-ipa-1-out" - represents the out gpio from
ipa driver to modem.
-compatible: "qcom,smp2pgpio-map-ipa-1-in" - represents the in gpio to
ipa driver from modem.
-gpios: Binding to the gpio defined in XXX-smp2p.dtsi
Example:
qcom,ipa@fd4c0000 {
compatible = "qcom,ipa";
reg = <0xfd4c0000 0x26000>,
<0xfd4c4000 0x14818>;
<0xfc834000 0x7000>;
reg-names = "ipa-base", "bam-base"; "a2-bam-base";
interrupts = <0 252 0>,
<0 253 0>;
<0 29 1>;
interrupt-names = "ipa-irq", "bam-irq"; "a2-bam-irq";
qcom,ipa-hw-ver = <1>;
clocks = <&clock_rpm clk_ipa_clk>;
clock-names = "iface_clk";
qcom,msm-bus,name = "ipa";
qcom,msm-bus,num-cases = <3>;
qcom,msm-bus,num-paths = <2>;
qcom,msm-bus,vectors-KBps =
<90 512 0 0>, <90 585 0 0>, /* No vote */
<90 512 100000 800000>, <90 585 100000 800000>, /* SVS */
<90 512 100000 1200000>, <90 585 100000 1200000>; /* PERF */
qcom,bus-vector-names = "MIN", "SVS", "PERF";
qcom,pipe1 {
label = "a2-to-ipa";
qcom,src-bam-physical-address = <0xfc834000>;
qcom,ipa-bam-mem-type = <0>;
qcom,src-bam-pipe-index = <1>;
qcom,dst-bam-physical-address = <0xfd4c0000>;
qcom,dst-bam-pipe-index = <6>;
qcom,data-fifo-offset = <0x1000>;
qcom,data-fifo-size = <0xd00>;
qcom,descriptor-fifo-offset = <0x1d00>;
qcom,descriptor-fifo-size = <0x300>;
};
qcom,pipe2 {
label = "ipa-to-a2";
qcom,src-bam-physical-address = <0xfd4c0000>;
qcom,ipa-bam-mem-type = <0>;
qcom,src-bam-pipe-index = <7>;
qcom,dst-bam-physical-address = <0xfc834000>;
qcom,dst-bam-pipe-index = <0>;
qcom,data-fifo-offset = <0x00>;
qcom,data-fifo-size = <0xd00>;
qcom,descriptor-fifo-offset = <0xd00>;
qcom,descriptor-fifo-size = <0x300>;
};
/* smp2p gpio information */
qcom,smp2pgpio_map_ipa_1_out {
compatible = "qcom,smp2pgpio-map-ipa-1-out";
gpios = <&smp2pgpio_ipa_1_out 0 0>;
};
qcom,smp2pgpio_map_ipa_1_in {
compatible = "qcom,smp2pgpio-map-ipa-1-in";
gpios = <&smp2pgpio_ipa_1_in 0 0>;
};
ipa_smmu_ap: ipa_smmu_ap {
compatible = "qcom,ipa-smmu-ap-cb";
iommus = <&apps_smmu 0x720>;
qcom,iova-mapping = <0x20000000 0x40000000>;
qcom,additional-mapping =
/* modem tables in IMEM */
<0x146bd000 0x146bd000 0x2000>;
};
ipa_smmu_wlan: ipa_smmu_wlan {
compatible = "qcom,ipa-smmu-wlan-cb";
iommus = <&apps_smmu 0x721>;
qcom,additional-mapping =
/* ipa-uc ram */
<0x1e60000 0x1e60000 0x80000>;
};
ipa_smmu_uc: ipa_smmu_uc {
compatible = "qcom,ipa-smmu-uc-cb";
iommus = <&apps_smmu 0x722>;
qcom,iova-mapping = <0x40000000 0x20000000>;
};
};