| /* |
| * linux/include/asm-arm/arch-l7200/serial_l7200.h |
| * |
| * Copyright (c) 2000 Steven Hill (sjhill@cotw.com) |
| * |
| * Changelog: |
| * 05-09-2000 SJH Created |
| */ |
| #ifndef __ASM_ARCH_SERIAL_L7200_H |
| #define __ASM_ARCH_SERIAL_L7200_H |
| |
| #include <asm/arch/memory.h> |
| |
| /* |
| * This assumes you have a 3.6864 MHz clock for your UART. |
| */ |
| #define BASE_BAUD 3686400 |
| |
| /* |
| * UART base register addresses |
| */ |
| #define UART1_BASE (IO_BASE + 0x00044000) |
| #define UART2_BASE (IO_BASE + 0x00045000) |
| |
| /* |
| * UART register offsets |
| */ |
| #define UARTDR 0x00 /* Tx/Rx data */ |
| #define RXSTAT 0x04 /* Rx status */ |
| #define H_UBRLCR 0x08 /* mode register high */ |
| #define M_UBRLCR 0x0C /* mode reg mid (MSB of baud)*/ |
| #define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/ |
| #define UARTCON 0x14 /* control register */ |
| #define UARTFLG 0x18 /* flag register */ |
| #define UARTINTSTAT 0x1C /* FIFO IRQ status register */ |
| #define UARTINTMASK 0x20 /* FIFO IRQ mask register */ |
| |
| /* |
| * UART baud rate register values |
| */ |
| #define BR_110 0x827 |
| #define BR_1200 0x06e |
| #define BR_2400 0x05f |
| #define BR_4800 0x02f |
| #define BR_9600 0x017 |
| #define BR_14400 0x00f |
| #define BR_19200 0x00b |
| #define BR_38400 0x005 |
| #define BR_57600 0x003 |
| #define BR_76800 0x002 |
| #define BR_115200 0x001 |
| |
| /* |
| * Receiver status register (RXSTAT) mask values |
| */ |
| #define RXSTAT_NO_ERR 0x00 /* No error */ |
| #define RXSTAT_FRM_ERR 0x01 /* Framing error */ |
| #define RXSTAT_PAR_ERR 0x02 /* Parity error */ |
| #define RXSTAT_OVR_ERR 0x04 /* Overrun error */ |
| |
| /* |
| * High byte of UART bit rate and line control register (H_UBRLCR) values |
| */ |
| #define UBRLCR_BRK 0x01 /* generate break on tx */ |
| #define UBRLCR_PEN 0x02 /* enable parity */ |
| #define UBRLCR_PDIS 0x00 /* disable parity */ |
| #define UBRLCR_EVEN 0x04 /* 1= even parity,0 = odd parity */ |
| #define UBRLCR_STP2 0x08 /* transmit 2 stop bits */ |
| #define UBRLCR_FIFO 0x10 /* enable FIFO */ |
| #define UBRLCR_LEN5 0x60 /* word length5 */ |
| #define UBRLCR_LEN6 0x40 /* word length6 */ |
| #define UBRLCR_LEN7 0x20 /* word length7 */ |
| #define UBRLCR_LEN8 0x00 /* word length8 */ |
| |
| /* |
| * UART control register (UARTCON) values |
| */ |
| #define UARTCON_UARTEN 0x01 /* Enable UART */ |
| #define UARTCON_DMAONERR 0x08 /* Mask RxDmaRq when errors occur */ |
| |
| /* |
| * UART flag register (UARTFLG) mask values |
| */ |
| #define UARTFLG_UTXFF 0x20 /* Transmit FIFO full */ |
| #define UARTFLG_URXFE 0x10 /* Receiver FIFO empty */ |
| #define UARTFLG_UBUSY 0x08 /* Transmitter busy */ |
| #define UARTFLG_DCD 0x04 /* Data carrier detect */ |
| #define UARTFLG_DSR 0x02 /* Data set ready */ |
| #define UARTFLG_CTS 0x01 /* Clear to send */ |
| |
| /* |
| * UART interrupt status/clear registers (UARTINTSTAT/CLR) values |
| */ |
| #define UART_TXINT 0x01 /* TX interrupt */ |
| #define UART_RXINT 0x02 /* RX interrupt */ |
| #define UART_RXERRINT 0x04 /* RX error interrupt */ |
| #define UART_MSINT 0x08 /* Modem Status interrupt */ |
| #define UART_UDINT 0x10 /* UART Disabled interrupt */ |
| #define UART_ALLIRQS 0x1f /* All interrupts */ |
| |
| #endif |