Documentation/devicetree/bindings/power/apm.txt

MSM Array Power Mux (msm-apm)

In some MSM designs, the CPU and caches contain logic which can be powered by
multiple rails. The APM controller exists to enable the selection of the power
rail supplying these arrays. Since a given supply may drop below the array
SRAM minimum operating voltage, the APM controller can be used to request a
switch to a power supply that will guarantee logic state retention.

Required properties
- compatible:	"qcom,msm-apm", "qcom,msm8996pro-apm", "qcom,msm8953-apm"
- reg:		Specifies physical base address and size of memory mapped regions
		containing the APM controller, APCS CSR, APC PLL controller, and
		SPM event registers.
- reg-names:	List of strings identifying the reg property entries. This list must
		contain: "pm-apcc-glb", "apcs-csr", "apc0-pll-ctl", "apc1-pll-ctl",
		"apc0-cpu0-spm", "apc0-cpu1-spm", "apc1-cpu0-spm", "apc1-cpu1-spm",
		"apc0-l2-spm", and "apc1-l2-spm".

Optional properties
- qcom,clock-source-override:	Specify this property to request a switch of the APC0 and APC1
				clock sources to GPLL0 before the APM switch begins and to
				switch back to the original clock source after the APM switch
				completes.
- qcom,apm-post-halt-delay:	The APM controller post halt delay counter value that SW needs
				to program one time before starting the APM HW controller for
				msm8953 target.
- qcom,apm-halt-clk-delay:	The APM controller halt clock delay counter value that SW
				needs to program one time before starting the APM HW controller
				for msm8953 target.
- qcom,apm-resume-clk-delay:	The APM controller resume clock delay counter value that SW
				needs to program one time before starting the APM HW controller
				for msm8953 target.
- qcom,apm-sel-switch-delay:	The APM controller switch selection delay counter value that SW
				needs to program one time before starting the APM HW controller
				for msm8953 target.

MSM APM Users

Required properties:
- qcom,apm-ctrl:		phandle of APM controller device node

Example:
	apc_apm: apm@099e0000 {
		compatible = "qcom,msm-apm";
		reg = <0x099e0000 0x1000>,
			<0x09820000 0x10000>,
			<0x06400050 0x8>,
			<0x06480050 0x8>,
			<0x09981068 0x8>,
			<0x09991068 0x8>,
			<0x099b1068 0x8>,
			<0x099c1068 0x8>,
			<0x099a1068 0x8>,
			<0x099d1068 0x8>;
		reg-names = "pm-apcc-glb",
				"apcs-csr",
				"apc0-pll-ctl",
				"apc1-pll-ctl",
				"apc0-cpu0-spm",
				"apc0-cpu1-spm",
				"apc1-cpu0-spm",
				"apc1-cpu1-spm",
				"apc0-l2-spm",
				"apc1-l2-spm";
		qcom,apm-post-halt-delay = <0x2>;
		qcom,apm-halt-clk-delay = <0x11>;
		qcom,apm-resume-clk-delay = <0x10>;
		qcom,apm-sel-switch-delay = <0x01>;

	foo_user {
		...
		qcom,apm-ctrl = <&apc_apm>;
	};