drivers/pcmcia/ricoh.h - kernel/msm-4.9 - Gitiles

 /*
  * ricoh.h 1.9 1999/10/25 20:03:34
  *
  * The contents of this file are subject to the Mozilla Public License
  * Version 1.1 (the "License"); you may not use this file except in
  * compliance with the License. You may obtain a copy of the License
  * at http://www.mozilla.org/MPL/
  *
  * Software distributed under the License is distributed on an "AS IS"
  * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
  * the License for the specific language governing rights and
  * limitations under the License.
  *
  * The initial developer of the original code is David A. Hinds
  * <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
  * are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
  *
  * Alternatively, the contents of this file may be used under the
  * terms of the GNU General Public License version 2 (the "GPL"), in which
  * case the provisions of the GPL are applicable instead of the
  * above.  If you wish to allow the use of your version of this file
  * only under the terms of the GPL and not to allow others to use
  * your version of this file under the MPL, indicate your decision by
  * deleting the provisions above and replace them with the notice and
  * other provisions required by the GPL.  If you do not delete the
  * provisions above, a recipient may use your version of this file
  * under either the MPL or the GPL.
  */

 #ifndef _LINUX_RICOH_H
 #define _LINUX_RICOH_H


 #define RF5C_MODE_CTL		0x1f	/* Mode control */
 #define RF5C_PWR_CTL		0x2f	/* Mixed voltage control */
 #define RF5C_CHIP_ID		0x3a	/* Chip identification */
 #define RF5C_MODE_CTL_3		0x3b	/* Mode control 3 */

 /* I/O window address offset */
 #define RF5C_IO_OFF(w)		(0x36+((w)<<1))

 /* Flags for RF5C_MODE_CTL */
 #define RF5C_MODE_ATA		0x01	/* ATA mode */
 #define RF5C_MODE_LED_ENA	0x02	/* IRQ 12 is LED */
 #define RF5C_MODE_CA21		0x04
 #define RF5C_MODE_CA22		0x08
 #define RF5C_MODE_CA23		0x10
 #define RF5C_MODE_CA24		0x20
 #define RF5C_MODE_CA25		0x40
 #define RF5C_MODE_3STATE_BIT7	0x80

 /* Flags for RF5C_PWR_CTL */
 #define RF5C_PWR_VCC_3V		0x01
 #define RF5C_PWR_IREQ_HIGH	0x02
 #define RF5C_PWR_INPACK_ENA	0x04
 #define RF5C_PWR_5V_DET		0x08
 #define RF5C_PWR_TC_SEL		0x10	/* Terminal Count: irq 11 or 15 */
 #define RF5C_PWR_DREQ_LOW	0x20
 #define RF5C_PWR_DREQ_OFF	0x00	/* DREQ steering control */
 #define RF5C_PWR_DREQ_INPACK	0x40
 #define RF5C_PWR_DREQ_SPKR	0x80
 #define RF5C_PWR_DREQ_IOIS16	0xc0

 /* Values for RF5C_CHIP_ID */
 #define RF5C_CHIP_RF5C296	0x32
 #define RF5C_CHIP_RF5C396	0xb2

 /* Flags for RF5C_MODE_CTL_3 */
 #define RF5C_MCTL3_DISABLE	0x01	/* Disable PCMCIA interface */
 #define RF5C_MCTL3_DMA_ENA	0x02

 /* Register definitions for Ricoh PCI-to-CardBus bridges */

 /* Extra bits in CB_BRIDGE_CONTROL */
 #define RL5C46X_BCR_3E0_ENA		0x0800
 #define RL5C46X_BCR_3E2_ENA		0x1000

 /* Bridge Configuration Register */
 #define RL5C4XX_CONFIG			0x80	/* 16 bit */
 #define  RL5C4XX_CONFIG_IO_1_MODE	0x0200
 #define  RL5C4XX_CONFIG_IO_0_MODE	0x0100
 #define  RL5C4XX_CONFIG_PREFETCH	0x0001

 /* Misc Control Register */
 #define RL5C4XX_MISC			0x0082	/* 16 bit */
 #define  RL5C4XX_MISC_HW_SUSPEND_ENA	0x0002
 #define  RL5C4XX_MISC_VCCEN_POL		0x0100
 #define  RL5C4XX_MISC_VPPEN_POL		0x0200
 #define  RL5C46X_MISC_SUSPEND		0x0001
 #define  RL5C46X_MISC_PWR_SAVE_2	0x0004
 #define  RL5C46X_MISC_IFACE_BUSY	0x0008
 #define  RL5C46X_MISC_B_LOCK		0x0010
 #define  RL5C46X_MISC_A_LOCK		0x0020
 #define  RL5C46X_MISC_PCI_LOCK		0x0040
 #define  RL5C47X_MISC_IFACE_BUSY	0x0004
 #define  RL5C47X_MISC_PCI_INT_MASK	0x0018
 #define  RL5C47X_MISC_PCI_INT_DIS	0x0020
 #define  RL5C47X_MISC_SUBSYS_WR		0x0040
 #define  RL5C47X_MISC_SRIRQ_ENA		0x0080
 #define  RL5C47X_MISC_5V_DISABLE	0x0400
 #define  RL5C47X_MISC_LED_POL		0x0800

 /* 16-bit Interface Control Register */
 #define RL5C4XX_16BIT_CTL		0x0084	/* 16 bit */
 #define  RL5C4XX_16CTL_IO_TIMING	0x0100
 #define  RL5C4XX_16CTL_MEM_TIMING	0x0200
 #define  RL5C46X_16CTL_LEVEL_1		0x0010
 #define  RL5C46X_16CTL_LEVEL_2		0x0020

 /* 16-bit IO and memory timing registers */
 #define RL5C4XX_16BIT_IO_0		0x0088	/* 16 bit */
 #define RL5C4XX_16BIT_MEM_0		0x008a	/* 16 bit */
 #define  RL5C4XX_SETUP_MASK		0x0007
 #define  RL5C4XX_SETUP_SHIFT		0
 #define  RL5C4XX_CMD_MASK		0x01f0
 #define  RL5C4XX_CMD_SHIFT		4
 #define  RL5C4XX_HOLD_MASK		0x1c00
 #define  RL5C4XX_HOLD_SHIFT		10
 #define  RL5C4XX_MISC_CONTROL           0x2F /* 8 bit */
 #define  RL5C4XX_ZV_ENABLE              0x08

 #ifdef __YENTA_H

 #define rl_misc(socket)		((socket)->private[0])
 #define rl_ctl(socket)		((socket)->private[1])
 #define rl_io(socket)		((socket)->private[2])
 #define rl_mem(socket)		((socket)->private[3])
 #define rl_config(socket)	((socket)->private[4])

 static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
 {
         u8 reg;
 	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);

         reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
         if (onoff)
                 /* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
                 reg |=  RL5C4XX_ZV_ENABLE;
         else
                 reg &= ~RL5C4XX_ZV_ENABLE;

         config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
 }

 static void ricoh_set_zv(struct yenta_socket *socket)
 {
         if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
         {
                 switch(socket->dev->device)
                 {
                         /* There may be more .. */
 		case  PCI_DEVICE_ID_RICOH_RL5C478:
 			socket->socket.zoom_video = ricoh_zoom_video;
 			break;
                 }
         }
 }

 static void ricoh_save_state(struct yenta_socket *socket)
 {
 	rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
 	rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
 	rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
 	rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
 	rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
 }

 static void ricoh_restore_state(struct yenta_socket *socket)
 {
 	config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
 	config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
 	config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
 	config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
 	config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
 }


 /*
  * Magic Ricoh initialization code..
  */
 static int ricoh_override(struct yenta_socket *socket)
 {
 	u16 config, ctl;

 	config = config_readw(socket, RL5C4XX_CONFIG);

 	/* Set the default timings, don't trust the original values */
 	ctl = RL5C4XX_16CTL_IO_TIMING | RL5C4XX_16CTL_MEM_TIMING;

 	if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
 		ctl |= RL5C46X_16CTL_LEVEL_1 | RL5C46X_16CTL_LEVEL_2;
 	} else {
 		config |= RL5C4XX_CONFIG_PREFETCH;
 	}

 	config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
 	config_writew(socket, RL5C4XX_CONFIG, config);

 	ricoh_set_zv(socket);

 	return 0;
 }

 #endif /* CONFIG_CARDBUS */

 #endif /* _LINUX_RICOH_H */
	/*
	* ricoh.h 1.9 1999/10/25 20:03:34
	*
	* The contents of this file are subject to the Mozilla Public License
	* Version 1.1 (the "License"); you may not use this file except in
	* compliance with the License. You may obtain a copy of the License
	* at http://www.mozilla.org/MPL/
	*
	* Software distributed under the License is distributed on an "AS IS"
	* basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
	* the License for the specific language governing rights and
	* limitations under the License.
	*
	* The initial developer of the original code is David A. Hinds
	* <dahinds@users.sourceforge.net>. Portions created by David A. Hinds
	* are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
	*
	* Alternatively, the contents of this file may be used under the
	* terms of the GNU General Public License version 2 (the "GPL"), in which
	* case the provisions of the GPL are applicable instead of the
	* above. If you wish to allow the use of your version of this file
	* only under the terms of the GPL and not to allow others to use
	* your version of this file under the MPL, indicate your decision by
	* deleting the provisions above and replace them with the notice and
	* other provisions required by the GPL. If you do not delete the
	* provisions above, a recipient may use your version of this file
	* under either the MPL or the GPL.
	*/

	#ifndef _LINUX_RICOH_H
	#define _LINUX_RICOH_H


	#define RF5C_MODE_CTL 0x1f /* Mode control */
	#define RF5C_PWR_CTL 0x2f /* Mixed voltage control */
	#define RF5C_CHIP_ID 0x3a /* Chip identification */
	#define RF5C_MODE_CTL_3 0x3b /* Mode control 3 */

	/* I/O window address offset */
	#define RF5C_IO_OFF(w) (0x36+((w)<<1))

	/* Flags for RF5C_MODE_CTL */
	#define RF5C_MODE_ATA 0x01 /* ATA mode */
	#define RF5C_MODE_LED_ENA 0x02 /* IRQ 12 is LED */
	#define RF5C_MODE_CA21 0x04
	#define RF5C_MODE_CA22 0x08
	#define RF5C_MODE_CA23 0x10
	#define RF5C_MODE_CA24 0x20
	#define RF5C_MODE_CA25 0x40
	#define RF5C_MODE_3STATE_BIT7 0x80

	/* Flags for RF5C_PWR_CTL */
	#define RF5C_PWR_VCC_3V 0x01
	#define RF5C_PWR_IREQ_HIGH 0x02
	#define RF5C_PWR_INPACK_ENA 0x04
	#define RF5C_PWR_5V_DET 0x08
	#define RF5C_PWR_TC_SEL 0x10 /* Terminal Count: irq 11 or 15 */
	#define RF5C_PWR_DREQ_LOW 0x20
	#define RF5C_PWR_DREQ_OFF 0x00 /* DREQ steering control */
	#define RF5C_PWR_DREQ_INPACK 0x40
	#define RF5C_PWR_DREQ_SPKR 0x80
	#define RF5C_PWR_DREQ_IOIS16 0xc0

	/* Values for RF5C_CHIP_ID */
	#define RF5C_CHIP_RF5C296 0x32
	#define RF5C_CHIP_RF5C396 0xb2

	/* Flags for RF5C_MODE_CTL_3 */
	#define RF5C_MCTL3_DISABLE 0x01 /* Disable PCMCIA interface */
	#define RF5C_MCTL3_DMA_ENA 0x02

	/* Register definitions for Ricoh PCI-to-CardBus bridges */

	/* Extra bits in CB_BRIDGE_CONTROL */
	#define RL5C46X_BCR_3E0_ENA 0x0800
	#define RL5C46X_BCR_3E2_ENA 0x1000

	/* Bridge Configuration Register */
	#define RL5C4XX_CONFIG 0x80 /* 16 bit */
	#define RL5C4XX_CONFIG_IO_1_MODE 0x0200
	#define RL5C4XX_CONFIG_IO_0_MODE 0x0100
	#define RL5C4XX_CONFIG_PREFETCH 0x0001

	/* Misc Control Register */
	#define RL5C4XX_MISC 0x0082 /* 16 bit */
	#define RL5C4XX_MISC_HW_SUSPEND_ENA 0x0002
	#define RL5C4XX_MISC_VCCEN_POL 0x0100
	#define RL5C4XX_MISC_VPPEN_POL 0x0200
	#define RL5C46X_MISC_SUSPEND 0x0001
	#define RL5C46X_MISC_PWR_SAVE_2 0x0004
	#define RL5C46X_MISC_IFACE_BUSY 0x0008
	#define RL5C46X_MISC_B_LOCK 0x0010
	#define RL5C46X_MISC_A_LOCK 0x0020
	#define RL5C46X_MISC_PCI_LOCK 0x0040
	#define RL5C47X_MISC_IFACE_BUSY 0x0004
	#define RL5C47X_MISC_PCI_INT_MASK 0x0018
	#define RL5C47X_MISC_PCI_INT_DIS 0x0020
	#define RL5C47X_MISC_SUBSYS_WR 0x0040
	#define RL5C47X_MISC_SRIRQ_ENA 0x0080
	#define RL5C47X_MISC_5V_DISABLE 0x0400
	#define RL5C47X_MISC_LED_POL 0x0800

	/* 16-bit Interface Control Register */
	#define RL5C4XX_16BIT_CTL 0x0084 /* 16 bit */
	#define RL5C4XX_16CTL_IO_TIMING 0x0100
	#define RL5C4XX_16CTL_MEM_TIMING 0x0200
	#define RL5C46X_16CTL_LEVEL_1 0x0010
	#define RL5C46X_16CTL_LEVEL_2 0x0020

	/* 16-bit IO and memory timing registers */
	#define RL5C4XX_16BIT_IO_0 0x0088 /* 16 bit */
	#define RL5C4XX_16BIT_MEM_0 0x008a /* 16 bit */
	#define RL5C4XX_SETUP_MASK 0x0007
	#define RL5C4XX_SETUP_SHIFT 0
	#define RL5C4XX_CMD_MASK 0x01f0
	#define RL5C4XX_CMD_SHIFT 4
	#define RL5C4XX_HOLD_MASK 0x1c00
	#define RL5C4XX_HOLD_SHIFT 10
	#define RL5C4XX_MISC_CONTROL 0x2F /* 8 bit */
	#define RL5C4XX_ZV_ENABLE 0x08

	#ifdef __YENTA_H

	#define rl_misc(socket) ((socket)->private[0])
	#define rl_ctl(socket) ((socket)->private[1])
	#define rl_io(socket) ((socket)->private[2])
	#define rl_mem(socket) ((socket)->private[3])
	#define rl_config(socket) ((socket)->private[4])

	static void ricoh_zoom_video(struct pcmcia_socket *sock, int onoff)
	{
	u8 reg;
	struct yenta_socket *socket = container_of(sock, struct yenta_socket, socket);

	reg = config_readb(socket, RL5C4XX_MISC_CONTROL);
	if (onoff)
	/* Zoom zoom, we will all go together, zoom zoom, zoom zoom */
	reg \|= RL5C4XX_ZV_ENABLE;
	else
	reg &= ~RL5C4XX_ZV_ENABLE;

	config_writeb(socket, RL5C4XX_MISC_CONTROL, reg);
	}

	static void ricoh_set_zv(struct yenta_socket *socket)
	{
	if(socket->dev->vendor == PCI_VENDOR_ID_RICOH)
	{
	switch(socket->dev->device)
	{
	/* There may be more .. */
	case PCI_DEVICE_ID_RICOH_RL5C478:
	socket->socket.zoom_video = ricoh_zoom_video;
	break;
	}
	}
	}

	static void ricoh_save_state(struct yenta_socket *socket)
	{
	rl_misc(socket) = config_readw(socket, RL5C4XX_MISC);
	rl_ctl(socket) = config_readw(socket, RL5C4XX_16BIT_CTL);
	rl_io(socket) = config_readw(socket, RL5C4XX_16BIT_IO_0);
	rl_mem(socket) = config_readw(socket, RL5C4XX_16BIT_MEM_0);
	rl_config(socket) = config_readw(socket, RL5C4XX_CONFIG);
	}

	static void ricoh_restore_state(struct yenta_socket *socket)
	{
	config_writew(socket, RL5C4XX_MISC, rl_misc(socket));
	config_writew(socket, RL5C4XX_16BIT_CTL, rl_ctl(socket));
	config_writew(socket, RL5C4XX_16BIT_IO_0, rl_io(socket));
	config_writew(socket, RL5C4XX_16BIT_MEM_0, rl_mem(socket));
	config_writew(socket, RL5C4XX_CONFIG, rl_config(socket));
	}


	/*
	* Magic Ricoh initialization code..
	*/
	static int ricoh_override(struct yenta_socket *socket)
	{
	u16 config, ctl;

	config = config_readw(socket, RL5C4XX_CONFIG);

	/* Set the default timings, don't trust the original values */
	ctl = RL5C4XX_16CTL_IO_TIMING \| RL5C4XX_16CTL_MEM_TIMING;

	if(socket->dev->device < PCI_DEVICE_ID_RICOH_RL5C475) {
	ctl \|= RL5C46X_16CTL_LEVEL_1 \| RL5C46X_16CTL_LEVEL_2;
	} else {
	config \|= RL5C4XX_CONFIG_PREFETCH;
	}

	config_writew(socket, RL5C4XX_16BIT_CTL, ctl);
	config_writew(socket, RL5C4XX_CONFIG, config);

	ricoh_set_zv(socket);

	return 0;
	}

	#endif /* CONFIG_CARDBUS */

	#endif /* _LINUX_RICOH_H */