blob: 0df1391f9663b257a170e5bbf6503268207b3d2d [file] [log] [blame]
#
# QLogic network device configuration
#
config NET_VENDOR_QLOGIC
bool "QLogic devices"
default y
depends on PCI
---help---
If you have a network (Ethernet) card belonging to this class, say Y.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about QLogic cards. If you say Y, you will be asked for
your specific card in the following questions.
if NET_VENDOR_QLOGIC
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
depends on PCI
---help---
This driver supports QLogic ISP3XXX gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called qla3xxx.
config QLCNIC
tristate "QLOGIC QLCNIC 1/10Gb Converged Ethernet NIC Support"
depends on PCI
select FW_LOADER
---help---
This driver supports QLogic QLE8240 and QLE8242 Converged Ethernet
devices.
config QLCNIC_SRIOV
bool "QLOGIC QLCNIC 83XX family SR-IOV Support"
depends on QLCNIC && PCI_IOV
default y
---help---
This configuration parameter enables Single Root Input Output
Virtualization support for QLE83XX Converged Ethernet devices.
This allows for virtual function acceleration in virtualized
environments.
config QLCNIC_DCB
bool "QLOGIC QLCNIC 82XX and 83XX family DCB Support"
depends on QLCNIC && DCB
default y
---help---
This configuration parameter enables DCB support in QLE83XX
and QLE82XX Converged Ethernet devices. This allows for DCB
get operations support through rtNetlink interface. Only CEE
mode of DCB is supported. PG and PFC values are related only
to Tx.
config QLCNIC_HWMON
bool "QLOGIC QLCNIC 82XX and 83XX family HWMON support"
depends on QLCNIC && HWMON && !(QLCNIC=y && HWMON=m)
default y
---help---
This configuration parameter can be used to read the
board temperature in Converged Ethernet devices
supported by qlcnic.
This data is available via the hwmon sysfs interface.
config QLGE
tristate "QLogic QLGE 10Gb Ethernet Driver Support"
depends on PCI
---help---
This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called qlge.
config NETXEN_NIC
tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
depends on PCI
select FW_LOADER
---help---
This enables the support for NetXen's Gigabit Ethernet card.
config QED
tristate "QLogic QED 25/40/100Gb core driver"
depends on PCI
select ZLIB_INFLATE
---help---
This enables the support for ...
config QED_LL2
bool
config QED_SRIOV
bool "QLogic QED 25/40/100Gb SR-IOV support"
depends on QED && PCI_IOV
default y
---help---
This configuration parameter enables Single Root Input Output
Virtualization support for QED devices.
This allows for virtual function acceleration in virtualized
environments.
config QEDE
tristate "QLogic QED 25/40/100Gb Ethernet NIC"
depends on QED
---help---
This enables the support for ...
config INFINIBAND_QEDR
tristate "QLogic qede RoCE sources [debug]"
depends on QEDE && 64BIT
select QED_LL2
default n
---help---
This provides a temporary node that allows the compilation
and logical testing of the InfiniBand over Ethernet support
for QLogic QED. This would be replaced by the 'real' option
once the QEDR driver is added [+relocated].
endif # NET_VENDOR_QLOGIC