| /* |
| * Copyright (c) 2016, Fuzhou Rockchip Electronics Co., Ltd |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| */ |
| #include <linux/clk.h> |
| #include <linux/component.h> |
| #include <linux/iopoll.h> |
| #include <linux/math64.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/regmap.h> |
| #include <linux/mfd/syscon.h> |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_crtc.h> |
| #include <drm/drm_crtc_helper.h> |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_of.h> |
| #include <drm/drm_panel.h> |
| #include <drm/drmP.h> |
| #include <video/mipi_display.h> |
| |
| #include "rockchip_drm_drv.h" |
| #include "rockchip_drm_vop.h" |
| |
| #define DRIVER_NAME "dw-mipi-dsi" |
| |
| #define GRF_SOC_CON6 0x025c |
| #define DSI0_SEL_VOP_LIT (1 << 6) |
| #define DSI1_SEL_VOP_LIT (1 << 9) |
| |
| #define DSI_VERSION 0x00 |
| #define DSI_PWR_UP 0x04 |
| #define RESET 0 |
| #define POWERUP BIT(0) |
| |
| #define DSI_CLKMGR_CFG 0x08 |
| #define TO_CLK_DIVIDSION(div) (((div) & 0xff) << 8) |
| #define TX_ESC_CLK_DIVIDSION(div) (((div) & 0xff) << 0) |
| |
| #define DSI_DPI_VCID 0x0c |
| #define DPI_VID(vid) (((vid) & 0x3) << 0) |
| |
| #define DSI_DPI_COLOR_CODING 0x10 |
| #define EN18_LOOSELY BIT(8) |
| #define DPI_COLOR_CODING_16BIT_1 0x0 |
| #define DPI_COLOR_CODING_16BIT_2 0x1 |
| #define DPI_COLOR_CODING_16BIT_3 0x2 |
| #define DPI_COLOR_CODING_18BIT_1 0x3 |
| #define DPI_COLOR_CODING_18BIT_2 0x4 |
| #define DPI_COLOR_CODING_24BIT 0x5 |
| |
| #define DSI_DPI_CFG_POL 0x14 |
| #define COLORM_ACTIVE_LOW BIT(4) |
| #define SHUTD_ACTIVE_LOW BIT(3) |
| #define HSYNC_ACTIVE_LOW BIT(2) |
| #define VSYNC_ACTIVE_LOW BIT(1) |
| #define DATAEN_ACTIVE_LOW BIT(0) |
| |
| #define DSI_DPI_LP_CMD_TIM 0x18 |
| #define OUTVACT_LPCMD_TIME(p) (((p) & 0xff) << 16) |
| #define INVACT_LPCMD_TIME(p) ((p) & 0xff) |
| |
| #define DSI_DBI_CFG 0x20 |
| #define DSI_DBI_CMDSIZE 0x28 |
| |
| #define DSI_PCKHDL_CFG 0x2c |
| #define EN_CRC_RX BIT(4) |
| #define EN_ECC_RX BIT(3) |
| #define EN_BTA BIT(2) |
| #define EN_EOTP_RX BIT(1) |
| #define EN_EOTP_TX BIT(0) |
| |
| #define DSI_MODE_CFG 0x34 |
| #define ENABLE_VIDEO_MODE 0 |
| #define ENABLE_CMD_MODE BIT(0) |
| |
| #define DSI_VID_MODE_CFG 0x38 |
| #define FRAME_BTA_ACK BIT(14) |
| #define ENABLE_LOW_POWER (0x3f << 8) |
| #define ENABLE_LOW_POWER_MASK (0x3f << 8) |
| #define VID_MODE_TYPE_BURST_SYNC_PULSES 0x2 |
| #define VID_MODE_TYPE_MASK 0x3 |
| |
| #define DSI_VID_PKT_SIZE 0x3c |
| #define VID_PKT_SIZE(p) (((p) & 0x3fff) << 0) |
| #define VID_PKT_MAX_SIZE 0x3fff |
| |
| #define DSI_VID_HSA_TIME 0x48 |
| #define DSI_VID_HBP_TIME 0x4c |
| #define DSI_VID_HLINE_TIME 0x50 |
| #define DSI_VID_VSA_LINES 0x54 |
| #define DSI_VID_VBP_LINES 0x58 |
| #define DSI_VID_VFP_LINES 0x5c |
| #define DSI_VID_VACTIVE_LINES 0x60 |
| #define DSI_CMD_MODE_CFG 0x68 |
| #define MAX_RD_PKT_SIZE_LP BIT(24) |
| #define DCS_LW_TX_LP BIT(19) |
| #define DCS_SR_0P_TX_LP BIT(18) |
| #define DCS_SW_1P_TX_LP BIT(17) |
| #define DCS_SW_0P_TX_LP BIT(16) |
| #define GEN_LW_TX_LP BIT(14) |
| #define GEN_SR_2P_TX_LP BIT(13) |
| #define GEN_SR_1P_TX_LP BIT(12) |
| #define GEN_SR_0P_TX_LP BIT(11) |
| #define GEN_SW_2P_TX_LP BIT(10) |
| #define GEN_SW_1P_TX_LP BIT(9) |
| #define GEN_SW_0P_TX_LP BIT(8) |
| #define EN_ACK_RQST BIT(1) |
| #define EN_TEAR_FX BIT(0) |
| |
| #define CMD_MODE_ALL_LP (MAX_RD_PKT_SIZE_LP | \ |
| DCS_LW_TX_LP | \ |
| DCS_SR_0P_TX_LP | \ |
| DCS_SW_1P_TX_LP | \ |
| DCS_SW_0P_TX_LP | \ |
| GEN_LW_TX_LP | \ |
| GEN_SR_2P_TX_LP | \ |
| GEN_SR_1P_TX_LP | \ |
| GEN_SR_0P_TX_LP | \ |
| GEN_SW_2P_TX_LP | \ |
| GEN_SW_1P_TX_LP | \ |
| GEN_SW_0P_TX_LP) |
| |
| #define DSI_GEN_HDR 0x6c |
| #define GEN_HDATA(data) (((data) & 0xffff) << 8) |
| #define GEN_HDATA_MASK (0xffff << 8) |
| #define GEN_HTYPE(type) (((type) & 0xff) << 0) |
| #define GEN_HTYPE_MASK 0xff |
| |
| #define DSI_GEN_PLD_DATA 0x70 |
| |
| #define DSI_CMD_PKT_STATUS 0x74 |
| #define GEN_CMD_EMPTY BIT(0) |
| #define GEN_CMD_FULL BIT(1) |
| #define GEN_PLD_W_EMPTY BIT(2) |
| #define GEN_PLD_W_FULL BIT(3) |
| #define GEN_PLD_R_EMPTY BIT(4) |
| #define GEN_PLD_R_FULL BIT(5) |
| #define GEN_RD_CMD_BUSY BIT(6) |
| |
| #define DSI_TO_CNT_CFG 0x78 |
| #define HSTX_TO_CNT(p) (((p) & 0xffff) << 16) |
| #define LPRX_TO_CNT(p) ((p) & 0xffff) |
| |
| #define DSI_BTA_TO_CNT 0x8c |
| |
| #define DSI_LPCLK_CTRL 0x94 |
| #define AUTO_CLKLANE_CTRL BIT(1) |
| #define PHY_TXREQUESTCLKHS BIT(0) |
| |
| #define DSI_PHY_TMR_LPCLK_CFG 0x98 |
| #define PHY_CLKHS2LP_TIME(lbcc) (((lbcc) & 0x3ff) << 16) |
| #define PHY_CLKLP2HS_TIME(lbcc) ((lbcc) & 0x3ff) |
| |
| #define DSI_PHY_TMR_CFG 0x9c |
| #define PHY_HS2LP_TIME(lbcc) (((lbcc) & 0xff) << 24) |
| #define PHY_LP2HS_TIME(lbcc) (((lbcc) & 0xff) << 16) |
| #define MAX_RD_TIME(lbcc) ((lbcc) & 0x7fff) |
| |
| #define DSI_PHY_RSTZ 0xa0 |
| #define PHY_DISFORCEPLL 0 |
| #define PHY_ENFORCEPLL BIT(3) |
| #define PHY_DISABLECLK 0 |
| #define PHY_ENABLECLK BIT(2) |
| #define PHY_RSTZ 0 |
| #define PHY_UNRSTZ BIT(1) |
| #define PHY_SHUTDOWNZ 0 |
| #define PHY_UNSHUTDOWNZ BIT(0) |
| |
| #define DSI_PHY_IF_CFG 0xa4 |
| #define N_LANES(n) ((((n) - 1) & 0x3) << 0) |
| #define PHY_STOP_WAIT_TIME(cycle) (((cycle) & 0xff) << 8) |
| |
| #define DSI_PHY_STATUS 0xb0 |
| #define LOCK BIT(0) |
| #define STOP_STATE_CLK_LANE BIT(2) |
| |
| #define DSI_PHY_TST_CTRL0 0xb4 |
| #define PHY_TESTCLK BIT(1) |
| #define PHY_UNTESTCLK 0 |
| #define PHY_TESTCLR BIT(0) |
| #define PHY_UNTESTCLR 0 |
| |
| #define DSI_PHY_TST_CTRL1 0xb8 |
| #define PHY_TESTEN BIT(16) |
| #define PHY_UNTESTEN 0 |
| #define PHY_TESTDOUT(n) (((n) & 0xff) << 8) |
| #define PHY_TESTDIN(n) (((n) & 0xff) << 0) |
| |
| #define DSI_INT_ST0 0xbc |
| #define DSI_INT_ST1 0xc0 |
| #define DSI_INT_MSK0 0xc4 |
| #define DSI_INT_MSK1 0xc8 |
| |
| #define PHY_STATUS_TIMEOUT_US 10000 |
| #define CMD_PKT_STATUS_TIMEOUT_US 20000 |
| |
| #define BYPASS_VCO_RANGE BIT(7) |
| #define VCO_RANGE_CON_SEL(val) (((val) & 0x7) << 3) |
| #define VCO_IN_CAP_CON_DEFAULT (0x0 << 1) |
| #define VCO_IN_CAP_CON_LOW (0x1 << 1) |
| #define VCO_IN_CAP_CON_HIGH (0x2 << 1) |
| #define REF_BIAS_CUR_SEL BIT(0) |
| |
| #define CP_CURRENT_3MA BIT(3) |
| #define CP_PROGRAM_EN BIT(7) |
| #define LPF_PROGRAM_EN BIT(6) |
| #define LPF_RESISTORS_20_KOHM 0 |
| |
| #define HSFREQRANGE_SEL(val) (((val) & 0x3f) << 1) |
| |
| #define INPUT_DIVIDER(val) ((val - 1) & 0x7f) |
| #define LOW_PROGRAM_EN 0 |
| #define HIGH_PROGRAM_EN BIT(7) |
| #define LOOP_DIV_LOW_SEL(val) ((val - 1) & 0x1f) |
| #define LOOP_DIV_HIGH_SEL(val) (((val - 1) >> 5) & 0x1f) |
| #define PLL_LOOP_DIV_EN BIT(5) |
| #define PLL_INPUT_DIV_EN BIT(4) |
| |
| #define POWER_CONTROL BIT(6) |
| #define INTERNAL_REG_CURRENT BIT(3) |
| #define BIAS_BLOCK_ON BIT(2) |
| #define BANDGAP_ON BIT(0) |
| |
| #define TER_RESISTOR_HIGH BIT(7) |
| #define TER_RESISTOR_LOW 0 |
| #define LEVEL_SHIFTERS_ON BIT(6) |
| #define TER_CAL_DONE BIT(5) |
| #define SETRD_MAX (0x7 << 2) |
| #define POWER_MANAGE BIT(1) |
| #define TER_RESISTORS_ON BIT(0) |
| |
| #define BIASEXTR_SEL(val) ((val) & 0x7) |
| #define BANDGAP_SEL(val) ((val) & 0x7) |
| #define TLP_PROGRAM_EN BIT(7) |
| #define THS_PRE_PROGRAM_EN BIT(7) |
| #define THS_ZERO_PROGRAM_EN BIT(6) |
| |
| enum { |
| BANDGAP_97_07, |
| BANDGAP_98_05, |
| BANDGAP_99_02, |
| BANDGAP_100_00, |
| BANDGAP_93_17, |
| BANDGAP_94_15, |
| BANDGAP_95_12, |
| BANDGAP_96_10, |
| }; |
| |
| enum { |
| BIASEXTR_87_1, |
| BIASEXTR_91_5, |
| BIASEXTR_95_9, |
| BIASEXTR_100, |
| BIASEXTR_105_94, |
| BIASEXTR_111_88, |
| BIASEXTR_118_8, |
| BIASEXTR_127_7, |
| }; |
| |
| struct dw_mipi_dsi_plat_data { |
| unsigned int max_data_lanes; |
| enum drm_mode_status (*mode_valid)(struct drm_connector *connector, |
| struct drm_display_mode *mode); |
| }; |
| |
| struct dw_mipi_dsi { |
| struct drm_encoder encoder; |
| struct drm_connector connector; |
| struct mipi_dsi_host dsi_host; |
| struct drm_panel *panel; |
| struct device *dev; |
| struct regmap *grf_regmap; |
| void __iomem *base; |
| |
| struct clk *pllref_clk; |
| struct clk *pclk; |
| |
| unsigned int lane_mbps; /* per lane */ |
| u32 channel; |
| u32 lanes; |
| u32 format; |
| u16 input_div; |
| u16 feedback_div; |
| struct drm_display_mode *mode; |
| |
| const struct dw_mipi_dsi_plat_data *pdata; |
| }; |
| |
| enum dw_mipi_dsi_mode { |
| DW_MIPI_DSI_CMD_MODE, |
| DW_MIPI_DSI_VID_MODE, |
| }; |
| |
| struct dphy_pll_testdin_map { |
| unsigned int max_mbps; |
| u8 testdin; |
| }; |
| |
| /* The table is based on 27MHz DPHY pll reference clock. */ |
| static const struct dphy_pll_testdin_map dptdin_map[] = { |
| { 90, 0x00}, { 100, 0x10}, { 110, 0x20}, { 130, 0x01}, |
| { 140, 0x11}, { 150, 0x21}, { 170, 0x02}, { 180, 0x12}, |
| { 200, 0x22}, { 220, 0x03}, { 240, 0x13}, { 250, 0x23}, |
| { 270, 0x04}, { 300, 0x14}, { 330, 0x05}, { 360, 0x15}, |
| { 400, 0x25}, { 450, 0x06}, { 500, 0x16}, { 550, 0x07}, |
| { 600, 0x17}, { 650, 0x08}, { 700, 0x18}, { 750, 0x09}, |
| { 800, 0x19}, { 850, 0x29}, { 900, 0x39}, { 950, 0x0a}, |
| {1000, 0x1a}, {1050, 0x2a}, {1100, 0x3a}, {1150, 0x0b}, |
| {1200, 0x1b}, {1250, 0x2b}, {1300, 0x3b}, {1350, 0x0c}, |
| {1400, 0x1c}, {1450, 0x2c}, {1500, 0x3c} |
| }; |
| |
| static int max_mbps_to_testdin(unsigned int max_mbps) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(dptdin_map); i++) |
| if (dptdin_map[i].max_mbps > max_mbps) |
| return dptdin_map[i].testdin; |
| |
| return -EINVAL; |
| } |
| |
| /* |
| * The controller should generate 2 frames before |
| * preparing the peripheral. |
| */ |
| static void dw_mipi_dsi_wait_for_two_frames(struct dw_mipi_dsi *dsi) |
| { |
| int refresh, two_frames; |
| |
| refresh = drm_mode_vrefresh(dsi->mode); |
| two_frames = DIV_ROUND_UP(MSEC_PER_SEC, refresh) * 2; |
| msleep(two_frames); |
| } |
| |
| static inline struct dw_mipi_dsi *host_to_dsi(struct mipi_dsi_host *host) |
| { |
| return container_of(host, struct dw_mipi_dsi, dsi_host); |
| } |
| |
| static inline struct dw_mipi_dsi *con_to_dsi(struct drm_connector *con) |
| { |
| return container_of(con, struct dw_mipi_dsi, connector); |
| } |
| |
| static inline struct dw_mipi_dsi *encoder_to_dsi(struct drm_encoder *encoder) |
| { |
| return container_of(encoder, struct dw_mipi_dsi, encoder); |
| } |
| static inline void dsi_write(struct dw_mipi_dsi *dsi, u32 reg, u32 val) |
| { |
| writel(val, dsi->base + reg); |
| } |
| |
| static inline u32 dsi_read(struct dw_mipi_dsi *dsi, u32 reg) |
| { |
| return readl(dsi->base + reg); |
| } |
| |
| static void dw_mipi_dsi_phy_write(struct dw_mipi_dsi *dsi, u8 test_code, |
| u8 test_data) |
| { |
| /* |
| * With the falling edge on TESTCLK, the TESTDIN[7:0] signal content |
| * is latched internally as the current test code. Test data is |
| * programmed internally by rising edge on TESTCLK. |
| */ |
| dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); |
| |
| dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0) | |
| PHY_TESTDIN(test_code)); |
| |
| dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); |
| |
| dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_UNTESTEN | PHY_TESTDOUT(0) | |
| PHY_TESTDIN(test_data)); |
| |
| dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); |
| } |
| |
| static int dw_mipi_dsi_phy_init(struct dw_mipi_dsi *dsi) |
| { |
| int ret, testdin, vco, val; |
| |
| vco = (dsi->lane_mbps < 200) ? 0 : (dsi->lane_mbps + 100) / 200; |
| |
| testdin = max_mbps_to_testdin(dsi->lane_mbps); |
| if (testdin < 0) { |
| dev_err(dsi->dev, |
| "failed to get testdin for %dmbps lane clock\n", |
| dsi->lane_mbps); |
| return testdin; |
| } |
| |
| dsi_write(dsi, DSI_PWR_UP, POWERUP); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x10, BYPASS_VCO_RANGE | |
| VCO_RANGE_CON_SEL(vco) | |
| VCO_IN_CAP_CON_LOW | |
| REF_BIAS_CUR_SEL); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x11, CP_CURRENT_3MA); |
| dw_mipi_dsi_phy_write(dsi, 0x12, CP_PROGRAM_EN | LPF_PROGRAM_EN | |
| LPF_RESISTORS_20_KOHM); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x44, HSFREQRANGE_SEL(testdin)); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x19, PLL_LOOP_DIV_EN | PLL_INPUT_DIV_EN); |
| dw_mipi_dsi_phy_write(dsi, 0x17, INPUT_DIVIDER(dsi->input_div)); |
| dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_LOW_SEL(dsi->feedback_div) | |
| LOW_PROGRAM_EN); |
| dw_mipi_dsi_phy_write(dsi, 0x18, LOOP_DIV_HIGH_SEL(dsi->feedback_div) | |
| HIGH_PROGRAM_EN); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x20, POWER_CONTROL | INTERNAL_REG_CURRENT | |
| BIAS_BLOCK_ON | BANDGAP_ON); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_LOW | TER_CAL_DONE | |
| SETRD_MAX | TER_RESISTORS_ON); |
| dw_mipi_dsi_phy_write(dsi, 0x21, TER_RESISTOR_HIGH | LEVEL_SHIFTERS_ON | |
| SETRD_MAX | POWER_MANAGE | |
| TER_RESISTORS_ON); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x22, LOW_PROGRAM_EN | |
| BIASEXTR_SEL(BIASEXTR_127_7)); |
| dw_mipi_dsi_phy_write(dsi, 0x22, HIGH_PROGRAM_EN | |
| BANDGAP_SEL(BANDGAP_96_10)); |
| |
| dw_mipi_dsi_phy_write(dsi, 0x70, TLP_PROGRAM_EN | 0xf); |
| dw_mipi_dsi_phy_write(dsi, 0x71, THS_PRE_PROGRAM_EN | 0x55); |
| dw_mipi_dsi_phy_write(dsi, 0x72, THS_ZERO_PROGRAM_EN | 0xa); |
| |
| dsi_write(dsi, DSI_PHY_RSTZ, PHY_ENFORCEPLL | PHY_ENABLECLK | |
| PHY_UNRSTZ | PHY_UNSHUTDOWNZ); |
| |
| |
| ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS, |
| val, val & LOCK, 1000, PHY_STATUS_TIMEOUT_US); |
| if (ret < 0) { |
| dev_err(dsi->dev, "failed to wait for phy lock state\n"); |
| return ret; |
| } |
| |
| ret = readx_poll_timeout(readl, dsi->base + DSI_PHY_STATUS, |
| val, val & STOP_STATE_CLK_LANE, 1000, |
| PHY_STATUS_TIMEOUT_US); |
| if (ret < 0) { |
| dev_err(dsi->dev, |
| "failed to wait for phy clk lane stop state\n"); |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| static int dw_mipi_dsi_get_lane_bps(struct dw_mipi_dsi *dsi) |
| { |
| unsigned int i, pre; |
| unsigned long mpclk, pllref, tmp; |
| unsigned int m = 1, n = 1, target_mbps = 1000; |
| unsigned int max_mbps = dptdin_map[ARRAY_SIZE(dptdin_map) - 1].max_mbps; |
| int bpp; |
| |
| bpp = mipi_dsi_pixel_format_to_bpp(dsi->format); |
| if (bpp < 0) { |
| dev_err(dsi->dev, "failed to get bpp for pixel format %d\n", |
| dsi->format); |
| return bpp; |
| } |
| |
| mpclk = DIV_ROUND_UP(dsi->mode->clock, MSEC_PER_SEC); |
| if (mpclk) { |
| /* take 1 / 0.9, since mbps must big than bandwidth of RGB */ |
| tmp = mpclk * (bpp / dsi->lanes) * 10 / 9; |
| if (tmp < max_mbps) |
| target_mbps = tmp; |
| else |
| dev_err(dsi->dev, "DPHY clock frequency is out of range\n"); |
| } |
| |
| pllref = DIV_ROUND_UP(clk_get_rate(dsi->pllref_clk), USEC_PER_SEC); |
| tmp = pllref; |
| |
| for (i = 1; i < 6; i++) { |
| pre = pllref / i; |
| if ((tmp > (target_mbps % pre)) && (target_mbps / pre < 512)) { |
| tmp = target_mbps % pre; |
| n = i; |
| m = target_mbps / pre; |
| } |
| if (tmp == 0) |
| break; |
| } |
| |
| dsi->lane_mbps = pllref / n * m; |
| dsi->input_div = n; |
| dsi->feedback_div = m; |
| |
| return 0; |
| } |
| |
| static int dw_mipi_dsi_host_attach(struct mipi_dsi_host *host, |
| struct mipi_dsi_device *device) |
| { |
| struct dw_mipi_dsi *dsi = host_to_dsi(host); |
| |
| if (device->lanes > dsi->pdata->max_data_lanes) { |
| dev_err(dsi->dev, "the number of data lanes(%u) is too many\n", |
| device->lanes); |
| return -EINVAL; |
| } |
| |
| if (!(device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) || |
| !(device->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)) { |
| dev_err(dsi->dev, "device mode is unsupported\n"); |
| return -EINVAL; |
| } |
| |
| dsi->lanes = device->lanes; |
| dsi->channel = device->channel; |
| dsi->format = device->format; |
| dsi->panel = of_drm_find_panel(device->dev.of_node); |
| if (dsi->panel) |
| return drm_panel_attach(dsi->panel, &dsi->connector); |
| |
| return -EINVAL; |
| } |
| |
| static int dw_mipi_dsi_host_detach(struct mipi_dsi_host *host, |
| struct mipi_dsi_device *device) |
| { |
| struct dw_mipi_dsi *dsi = host_to_dsi(host); |
| |
| drm_panel_detach(dsi->panel); |
| |
| return 0; |
| } |
| |
| static int dw_mipi_dsi_gen_pkt_hdr_write(struct dw_mipi_dsi *dsi, u32 val) |
| { |
| int ret; |
| |
| ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS, |
| val, !(val & GEN_CMD_FULL), 1000, |
| CMD_PKT_STATUS_TIMEOUT_US); |
| if (ret < 0) { |
| dev_err(dsi->dev, "failed to get available command FIFO\n"); |
| return ret; |
| } |
| |
| dsi_write(dsi, DSI_GEN_HDR, val); |
| |
| ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS, |
| val, val & (GEN_CMD_EMPTY | GEN_PLD_W_EMPTY), |
| 1000, CMD_PKT_STATUS_TIMEOUT_US); |
| if (ret < 0) { |
| dev_err(dsi->dev, "failed to write command FIFO\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int dw_mipi_dsi_dcs_short_write(struct dw_mipi_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| const u16 *tx_buf = msg->tx_buf; |
| u32 val = GEN_HDATA(*tx_buf) | GEN_HTYPE(msg->type); |
| |
| if (msg->tx_len > 2) { |
| dev_err(dsi->dev, "too long tx buf length %zu for short write\n", |
| msg->tx_len); |
| return -EINVAL; |
| } |
| |
| return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val); |
| } |
| |
| static int dw_mipi_dsi_dcs_long_write(struct dw_mipi_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| const u32 *tx_buf = msg->tx_buf; |
| int len = msg->tx_len, pld_data_bytes = sizeof(*tx_buf), ret; |
| u32 val = GEN_HDATA(msg->tx_len) | GEN_HTYPE(msg->type); |
| u32 remainder = 0; |
| |
| if (msg->tx_len < 3) { |
| dev_err(dsi->dev, "wrong tx buf length %zu for long write\n", |
| msg->tx_len); |
| return -EINVAL; |
| } |
| |
| while (DIV_ROUND_UP(len, pld_data_bytes)) { |
| if (len < pld_data_bytes) { |
| memcpy(&remainder, tx_buf, len); |
| dsi_write(dsi, DSI_GEN_PLD_DATA, remainder); |
| len = 0; |
| } else { |
| dsi_write(dsi, DSI_GEN_PLD_DATA, *tx_buf); |
| tx_buf++; |
| len -= pld_data_bytes; |
| } |
| |
| ret = readx_poll_timeout(readl, dsi->base + DSI_CMD_PKT_STATUS, |
| val, !(val & GEN_PLD_W_FULL), 1000, |
| CMD_PKT_STATUS_TIMEOUT_US); |
| if (ret < 0) { |
| dev_err(dsi->dev, |
| "failed to get available write payload FIFO\n"); |
| return ret; |
| } |
| } |
| |
| return dw_mipi_dsi_gen_pkt_hdr_write(dsi, val); |
| } |
| |
| static ssize_t dw_mipi_dsi_host_transfer(struct mipi_dsi_host *host, |
| const struct mipi_dsi_msg *msg) |
| { |
| struct dw_mipi_dsi *dsi = host_to_dsi(host); |
| int ret; |
| |
| switch (msg->type) { |
| case MIPI_DSI_DCS_SHORT_WRITE: |
| case MIPI_DSI_DCS_SHORT_WRITE_PARAM: |
| case MIPI_DSI_SET_MAXIMUM_RETURN_PACKET_SIZE: |
| ret = dw_mipi_dsi_dcs_short_write(dsi, msg); |
| break; |
| case MIPI_DSI_DCS_LONG_WRITE: |
| ret = dw_mipi_dsi_dcs_long_write(dsi, msg); |
| break; |
| default: |
| dev_err(dsi->dev, "unsupported message type\n"); |
| ret = -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| static const struct mipi_dsi_host_ops dw_mipi_dsi_host_ops = { |
| .attach = dw_mipi_dsi_host_attach, |
| .detach = dw_mipi_dsi_host_detach, |
| .transfer = dw_mipi_dsi_host_transfer, |
| }; |
| |
| static void dw_mipi_dsi_video_mode_config(struct dw_mipi_dsi *dsi) |
| { |
| u32 val; |
| |
| val = VID_MODE_TYPE_BURST_SYNC_PULSES | ENABLE_LOW_POWER; |
| |
| dsi_write(dsi, DSI_VID_MODE_CFG, val); |
| } |
| |
| static void dw_mipi_dsi_set_mode(struct dw_mipi_dsi *dsi, |
| enum dw_mipi_dsi_mode mode) |
| { |
| if (mode == DW_MIPI_DSI_CMD_MODE) { |
| dsi_write(dsi, DSI_PWR_UP, RESET); |
| dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); |
| dsi_write(dsi, DSI_PWR_UP, POWERUP); |
| } else { |
| dsi_write(dsi, DSI_PWR_UP, RESET); |
| dsi_write(dsi, DSI_MODE_CFG, ENABLE_VIDEO_MODE); |
| dw_mipi_dsi_video_mode_config(dsi); |
| dsi_write(dsi, DSI_PWR_UP, POWERUP); |
| } |
| } |
| |
| static void dw_mipi_dsi_disable(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_PWR_UP, RESET); |
| dsi_write(dsi, DSI_PHY_RSTZ, PHY_RSTZ); |
| } |
| |
| static void dw_mipi_dsi_init(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_PWR_UP, RESET); |
| dsi_write(dsi, DSI_PHY_RSTZ, PHY_DISFORCEPLL | PHY_DISABLECLK |
| | PHY_RSTZ | PHY_SHUTDOWNZ); |
| dsi_write(dsi, DSI_CLKMGR_CFG, TO_CLK_DIVIDSION(10) | |
| TX_ESC_CLK_DIVIDSION(7)); |
| dsi_write(dsi, DSI_LPCLK_CTRL, PHY_TXREQUESTCLKHS); |
| } |
| |
| static void dw_mipi_dsi_dpi_config(struct dw_mipi_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| u32 val = 0, color = 0; |
| |
| switch (dsi->format) { |
| case MIPI_DSI_FMT_RGB888: |
| color = DPI_COLOR_CODING_24BIT; |
| break; |
| case MIPI_DSI_FMT_RGB666: |
| color = DPI_COLOR_CODING_18BIT_2 | EN18_LOOSELY; |
| break; |
| case MIPI_DSI_FMT_RGB666_PACKED: |
| color = DPI_COLOR_CODING_18BIT_1; |
| break; |
| case MIPI_DSI_FMT_RGB565: |
| color = DPI_COLOR_CODING_16BIT_1; |
| break; |
| } |
| |
| if (!(mode->flags & DRM_MODE_FLAG_PVSYNC)) |
| val |= VSYNC_ACTIVE_LOW; |
| if (!(mode->flags & DRM_MODE_FLAG_PHSYNC)) |
| val |= HSYNC_ACTIVE_LOW; |
| |
| dsi_write(dsi, DSI_DPI_VCID, DPI_VID(dsi->channel)); |
| dsi_write(dsi, DSI_DPI_COLOR_CODING, color); |
| dsi_write(dsi, DSI_DPI_CFG_POL, val); |
| dsi_write(dsi, DSI_DPI_LP_CMD_TIM, OUTVACT_LPCMD_TIME(4) |
| | INVACT_LPCMD_TIME(4)); |
| } |
| |
| static void dw_mipi_dsi_packet_handler_config(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_PCKHDL_CFG, EN_CRC_RX | EN_ECC_RX | EN_BTA); |
| } |
| |
| static void dw_mipi_dsi_video_packet_config(struct dw_mipi_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| dsi_write(dsi, DSI_VID_PKT_SIZE, VID_PKT_SIZE(mode->hdisplay)); |
| } |
| |
| static void dw_mipi_dsi_command_mode_config(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_TO_CNT_CFG, HSTX_TO_CNT(1000) | LPRX_TO_CNT(1000)); |
| dsi_write(dsi, DSI_BTA_TO_CNT, 0xd00); |
| dsi_write(dsi, DSI_CMD_MODE_CFG, CMD_MODE_ALL_LP); |
| dsi_write(dsi, DSI_MODE_CFG, ENABLE_CMD_MODE); |
| } |
| |
| /* Get lane byte clock cycles. */ |
| static u32 dw_mipi_dsi_get_hcomponent_lbcc(struct dw_mipi_dsi *dsi, |
| u32 hcomponent) |
| { |
| u32 frac, lbcc; |
| |
| lbcc = hcomponent * dsi->lane_mbps * MSEC_PER_SEC / 8; |
| |
| frac = lbcc % dsi->mode->clock; |
| lbcc = lbcc / dsi->mode->clock; |
| if (frac) |
| lbcc++; |
| |
| return lbcc; |
| } |
| |
| static void dw_mipi_dsi_line_timer_config(struct dw_mipi_dsi *dsi) |
| { |
| u32 htotal, hsa, hbp, lbcc; |
| struct drm_display_mode *mode = dsi->mode; |
| |
| htotal = mode->htotal; |
| hsa = mode->hsync_end - mode->hsync_start; |
| hbp = mode->htotal - mode->hsync_end; |
| |
| lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, htotal); |
| dsi_write(dsi, DSI_VID_HLINE_TIME, lbcc); |
| |
| lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hsa); |
| dsi_write(dsi, DSI_VID_HSA_TIME, lbcc); |
| |
| lbcc = dw_mipi_dsi_get_hcomponent_lbcc(dsi, hbp); |
| dsi_write(dsi, DSI_VID_HBP_TIME, lbcc); |
| } |
| |
| static void dw_mipi_dsi_vertical_timing_config(struct dw_mipi_dsi *dsi) |
| { |
| u32 vactive, vsa, vfp, vbp; |
| struct drm_display_mode *mode = dsi->mode; |
| |
| vactive = mode->vdisplay; |
| vsa = mode->vsync_end - mode->vsync_start; |
| vfp = mode->vsync_start - mode->vdisplay; |
| vbp = mode->vtotal - mode->vsync_end; |
| |
| dsi_write(dsi, DSI_VID_VACTIVE_LINES, vactive); |
| dsi_write(dsi, DSI_VID_VSA_LINES, vsa); |
| dsi_write(dsi, DSI_VID_VFP_LINES, vfp); |
| dsi_write(dsi, DSI_VID_VBP_LINES, vbp); |
| } |
| |
| static void dw_mipi_dsi_dphy_timing_config(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_PHY_TMR_CFG, PHY_HS2LP_TIME(0x40) |
| | PHY_LP2HS_TIME(0x40) | MAX_RD_TIME(10000)); |
| |
| dsi_write(dsi, DSI_PHY_TMR_LPCLK_CFG, PHY_CLKHS2LP_TIME(0x40) |
| | PHY_CLKLP2HS_TIME(0x40)); |
| } |
| |
| static void dw_mipi_dsi_dphy_interface_config(struct dw_mipi_dsi *dsi) |
| { |
| dsi_write(dsi, DSI_PHY_IF_CFG, PHY_STOP_WAIT_TIME(0x20) | |
| N_LANES(dsi->lanes)); |
| } |
| |
| static void dw_mipi_dsi_clear_err(struct dw_mipi_dsi *dsi) |
| { |
| dsi_read(dsi, DSI_INT_ST0); |
| dsi_read(dsi, DSI_INT_ST1); |
| dsi_write(dsi, DSI_INT_MSK0, 0); |
| dsi_write(dsi, DSI_INT_MSK1, 0); |
| } |
| |
| static void dw_mipi_dsi_encoder_mode_set(struct drm_encoder *encoder, |
| struct drm_display_mode *mode, |
| struct drm_display_mode *adjusted_mode) |
| { |
| struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); |
| int ret; |
| |
| dsi->mode = adjusted_mode; |
| |
| ret = dw_mipi_dsi_get_lane_bps(dsi); |
| if (ret < 0) |
| return; |
| |
| if (clk_prepare_enable(dsi->pclk)) { |
| dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__); |
| return; |
| } |
| |
| dw_mipi_dsi_init(dsi); |
| dw_mipi_dsi_dpi_config(dsi, mode); |
| dw_mipi_dsi_packet_handler_config(dsi); |
| dw_mipi_dsi_video_mode_config(dsi); |
| dw_mipi_dsi_video_packet_config(dsi, mode); |
| dw_mipi_dsi_command_mode_config(dsi); |
| dw_mipi_dsi_line_timer_config(dsi); |
| dw_mipi_dsi_vertical_timing_config(dsi); |
| dw_mipi_dsi_dphy_timing_config(dsi); |
| dw_mipi_dsi_dphy_interface_config(dsi); |
| dw_mipi_dsi_clear_err(dsi); |
| if (drm_panel_prepare(dsi->panel)) |
| dev_err(dsi->dev, "failed to prepare panel\n"); |
| |
| clk_disable_unprepare(dsi->pclk); |
| } |
| |
| static void dw_mipi_dsi_encoder_disable(struct drm_encoder *encoder) |
| { |
| struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); |
| |
| drm_panel_disable(dsi->panel); |
| |
| if (clk_prepare_enable(dsi->pclk)) { |
| dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__); |
| return; |
| } |
| |
| dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); |
| drm_panel_unprepare(dsi->panel); |
| dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE); |
| |
| /* |
| * This is necessary to make sure the peripheral will be driven |
| * normally when the display is enabled again later. |
| */ |
| msleep(120); |
| |
| dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_CMD_MODE); |
| dw_mipi_dsi_disable(dsi); |
| clk_disable_unprepare(dsi->pclk); |
| } |
| |
| static void dw_mipi_dsi_encoder_commit(struct drm_encoder *encoder) |
| { |
| struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); |
| int mux = drm_of_encoder_active_endpoint_id(dsi->dev->of_node, encoder); |
| u32 val; |
| |
| if (clk_prepare_enable(dsi->pclk)) { |
| dev_err(dsi->dev, "%s: Failed to enable pclk\n", __func__); |
| return; |
| } |
| |
| dw_mipi_dsi_phy_init(dsi); |
| dw_mipi_dsi_wait_for_two_frames(dsi); |
| |
| dw_mipi_dsi_set_mode(dsi, DW_MIPI_DSI_VID_MODE); |
| drm_panel_enable(dsi->panel); |
| |
| clk_disable_unprepare(dsi->pclk); |
| |
| if (mux) |
| val = DSI0_SEL_VOP_LIT | (DSI0_SEL_VOP_LIT << 16); |
| else |
| val = DSI0_SEL_VOP_LIT << 16; |
| |
| regmap_write(dsi->grf_regmap, GRF_SOC_CON6, val); |
| dev_dbg(dsi->dev, "vop %s output to dsi0\n", (mux) ? "LIT" : "BIG"); |
| } |
| |
| static int |
| dw_mipi_dsi_encoder_atomic_check(struct drm_encoder *encoder, |
| struct drm_crtc_state *crtc_state, |
| struct drm_connector_state *conn_state) |
| { |
| struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state); |
| struct dw_mipi_dsi *dsi = encoder_to_dsi(encoder); |
| |
| switch (dsi->format) { |
| case MIPI_DSI_FMT_RGB888: |
| s->output_mode = ROCKCHIP_OUT_MODE_P888; |
| break; |
| case MIPI_DSI_FMT_RGB666: |
| s->output_mode = ROCKCHIP_OUT_MODE_P666; |
| break; |
| case MIPI_DSI_FMT_RGB565: |
| s->output_mode = ROCKCHIP_OUT_MODE_P565; |
| break; |
| default: |
| WARN_ON(1); |
| return -EINVAL; |
| } |
| |
| s->output_type = DRM_MODE_CONNECTOR_DSI; |
| |
| return 0; |
| } |
| |
| static struct drm_encoder_helper_funcs |
| dw_mipi_dsi_encoder_helper_funcs = { |
| .commit = dw_mipi_dsi_encoder_commit, |
| .mode_set = dw_mipi_dsi_encoder_mode_set, |
| .disable = dw_mipi_dsi_encoder_disable, |
| .atomic_check = dw_mipi_dsi_encoder_atomic_check, |
| }; |
| |
| static struct drm_encoder_funcs dw_mipi_dsi_encoder_funcs = { |
| .destroy = drm_encoder_cleanup, |
| }; |
| |
| static int dw_mipi_dsi_connector_get_modes(struct drm_connector *connector) |
| { |
| struct dw_mipi_dsi *dsi = con_to_dsi(connector); |
| |
| return drm_panel_get_modes(dsi->panel); |
| } |
| |
| static enum drm_mode_status dw_mipi_dsi_mode_valid( |
| struct drm_connector *connector, |
| struct drm_display_mode *mode) |
| { |
| struct dw_mipi_dsi *dsi = con_to_dsi(connector); |
| |
| enum drm_mode_status mode_status = MODE_OK; |
| |
| if (dsi->pdata->mode_valid) |
| mode_status = dsi->pdata->mode_valid(connector, mode); |
| |
| return mode_status; |
| } |
| |
| static struct drm_connector_helper_funcs dw_mipi_dsi_connector_helper_funcs = { |
| .get_modes = dw_mipi_dsi_connector_get_modes, |
| .mode_valid = dw_mipi_dsi_mode_valid, |
| }; |
| |
| static enum drm_connector_status |
| dw_mipi_dsi_detect(struct drm_connector *connector, bool force) |
| { |
| return connector_status_connected; |
| } |
| |
| static void dw_mipi_dsi_drm_connector_destroy(struct drm_connector *connector) |
| { |
| drm_connector_unregister(connector); |
| drm_connector_cleanup(connector); |
| } |
| |
| static struct drm_connector_funcs dw_mipi_dsi_atomic_connector_funcs = { |
| .dpms = drm_atomic_helper_connector_dpms, |
| .fill_modes = drm_helper_probe_single_connector_modes, |
| .detect = dw_mipi_dsi_detect, |
| .destroy = dw_mipi_dsi_drm_connector_destroy, |
| .reset = drm_atomic_helper_connector_reset, |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, |
| }; |
| |
| static int dw_mipi_dsi_register(struct drm_device *drm, |
| struct dw_mipi_dsi *dsi) |
| { |
| struct drm_encoder *encoder = &dsi->encoder; |
| struct drm_connector *connector = &dsi->connector; |
| struct device *dev = dsi->dev; |
| int ret; |
| |
| encoder->possible_crtcs = drm_of_find_possible_crtcs(drm, |
| dev->of_node); |
| /* |
| * If we failed to find the CRTC(s) which this encoder is |
| * supposed to be connected to, it's because the CRTC has |
| * not been registered yet. Defer probing, and hope that |
| * the required CRTC is added later. |
| */ |
| if (encoder->possible_crtcs == 0) |
| return -EPROBE_DEFER; |
| |
| drm_encoder_helper_add(&dsi->encoder, |
| &dw_mipi_dsi_encoder_helper_funcs); |
| ret = drm_encoder_init(drm, &dsi->encoder, &dw_mipi_dsi_encoder_funcs, |
| DRM_MODE_ENCODER_DSI, NULL); |
| if (ret) { |
| dev_err(dev, "Failed to initialize encoder with drm\n"); |
| return ret; |
| } |
| |
| drm_connector_helper_add(connector, |
| &dw_mipi_dsi_connector_helper_funcs); |
| |
| drm_connector_init(drm, &dsi->connector, |
| &dw_mipi_dsi_atomic_connector_funcs, |
| DRM_MODE_CONNECTOR_DSI); |
| |
| drm_mode_connector_attach_encoder(connector, encoder); |
| |
| return 0; |
| } |
| |
| static int rockchip_mipi_parse_dt(struct dw_mipi_dsi *dsi) |
| { |
| struct device_node *np = dsi->dev->of_node; |
| |
| dsi->grf_regmap = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); |
| if (IS_ERR(dsi->grf_regmap)) { |
| dev_err(dsi->dev, "Unable to get rockchip,grf\n"); |
| return PTR_ERR(dsi->grf_regmap); |
| } |
| |
| return 0; |
| } |
| |
| static enum drm_mode_status rk3288_mipi_dsi_mode_valid( |
| struct drm_connector *connector, |
| struct drm_display_mode *mode) |
| { |
| /* |
| * The VID_PKT_SIZE field in the DSI_VID_PKT_CFG |
| * register is 11-bit. |
| */ |
| if (mode->hdisplay > 0x7ff) |
| return MODE_BAD_HVALUE; |
| |
| /* |
| * The V_ACTIVE_LINES field in the DSI_VTIMING_CFG |
| * register is 11-bit. |
| */ |
| if (mode->vdisplay > 0x7ff) |
| return MODE_BAD_VVALUE; |
| |
| return MODE_OK; |
| } |
| |
| static struct dw_mipi_dsi_plat_data rk3288_mipi_dsi_drv_data = { |
| .max_data_lanes = 4, |
| .mode_valid = rk3288_mipi_dsi_mode_valid, |
| }; |
| |
| static const struct of_device_id dw_mipi_dsi_dt_ids[] = { |
| { |
| .compatible = "rockchip,rk3288-mipi-dsi", |
| .data = &rk3288_mipi_dsi_drv_data, |
| }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, dw_mipi_dsi_dt_ids); |
| |
| static int dw_mipi_dsi_bind(struct device *dev, struct device *master, |
| void *data) |
| { |
| const struct of_device_id *of_id = |
| of_match_device(dw_mipi_dsi_dt_ids, dev); |
| const struct dw_mipi_dsi_plat_data *pdata = of_id->data; |
| struct platform_device *pdev = to_platform_device(dev); |
| struct drm_device *drm = data; |
| struct dw_mipi_dsi *dsi; |
| struct resource *res; |
| int ret; |
| |
| dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); |
| if (!dsi) |
| return -ENOMEM; |
| |
| dsi->dev = dev; |
| dsi->pdata = pdata; |
| |
| ret = rockchip_mipi_parse_dt(dsi); |
| if (ret) |
| return ret; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!res) |
| return -ENODEV; |
| |
| dsi->base = devm_ioremap_resource(dev, res); |
| if (IS_ERR(dsi->base)) |
| return PTR_ERR(dsi->base); |
| |
| dsi->pllref_clk = devm_clk_get(dev, "ref"); |
| if (IS_ERR(dsi->pllref_clk)) { |
| ret = PTR_ERR(dsi->pllref_clk); |
| dev_err(dev, "Unable to get pll reference clock: %d\n", ret); |
| return ret; |
| } |
| |
| dsi->pclk = devm_clk_get(dev, "pclk"); |
| if (IS_ERR(dsi->pclk)) { |
| ret = PTR_ERR(dsi->pclk); |
| dev_err(dev, "Unable to get pclk: %d\n", ret); |
| return ret; |
| } |
| |
| ret = clk_prepare_enable(dsi->pllref_clk); |
| if (ret) { |
| dev_err(dev, "%s: Failed to enable pllref_clk\n", __func__); |
| return ret; |
| } |
| |
| ret = dw_mipi_dsi_register(drm, dsi); |
| if (ret) { |
| dev_err(dev, "Failed to register mipi_dsi: %d\n", ret); |
| goto err_pllref; |
| } |
| |
| dev_set_drvdata(dev, dsi); |
| |
| dsi->dsi_host.ops = &dw_mipi_dsi_host_ops; |
| dsi->dsi_host.dev = dev; |
| return mipi_dsi_host_register(&dsi->dsi_host); |
| |
| err_pllref: |
| clk_disable_unprepare(dsi->pllref_clk); |
| return ret; |
| } |
| |
| static void dw_mipi_dsi_unbind(struct device *dev, struct device *master, |
| void *data) |
| { |
| struct dw_mipi_dsi *dsi = dev_get_drvdata(dev); |
| |
| mipi_dsi_host_unregister(&dsi->dsi_host); |
| clk_disable_unprepare(dsi->pllref_clk); |
| } |
| |
| static const struct component_ops dw_mipi_dsi_ops = { |
| .bind = dw_mipi_dsi_bind, |
| .unbind = dw_mipi_dsi_unbind, |
| }; |
| |
| static int dw_mipi_dsi_probe(struct platform_device *pdev) |
| { |
| return component_add(&pdev->dev, &dw_mipi_dsi_ops); |
| } |
| |
| static int dw_mipi_dsi_remove(struct platform_device *pdev) |
| { |
| component_del(&pdev->dev, &dw_mipi_dsi_ops); |
| return 0; |
| } |
| |
| static struct platform_driver dw_mipi_dsi_driver = { |
| .probe = dw_mipi_dsi_probe, |
| .remove = dw_mipi_dsi_remove, |
| .driver = { |
| .of_match_table = dw_mipi_dsi_dt_ids, |
| .name = DRIVER_NAME, |
| }, |
| }; |
| module_platform_driver(dw_mipi_dsi_driver); |
| |
| MODULE_DESCRIPTION("ROCKCHIP MIPI DSI host controller driver"); |
| MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:" DRIVER_NAME); |