| /* |
| * Copyright (c) 2016-2018, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| /dts-v1/; |
| |
| #include "apq8017.dtsi" |
| #include "msm8917-cdp.dtsi" |
| #include "msm8917-pmi8950.dtsi" |
| #include "apq8017-rome.dtsi" |
| #include "apq8017-audio.dtsi" |
| #include "apq8017-pmi8950-cdp-wcd-rome.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. APQ8017-PMI8950 CDP \ |
| with WCD codec/Rome card"; |
| compatible = "qcom,apq8017-cdp", "qcom,apq8017", "qcom,cdp"; |
| qcom,board-id= <1 2>; |
| qcom,pmic-id = <0x10019 0x010011 0x0 0x0>; |
| }; |
| |
| &blsp1_uart1 { |
| status = "ok"; |
| }; |
| |
| &wcd9335 { |
| qcom,cdc-mic-unmute-delay = <50>; |
| }; |
| |
| &sdhc_2 { |
| /* device core power supply */ |
| /delete-property/vdd-supply; |
| /delete-property/qcom,vdd-voltage-level; |
| /delete-property/qcom,vdd-current-level; |
| |
| /* device communication power supply */ |
| vdd-io-supply = <&pm8937_l5>; |
| qcom,vdd-io-always-on; |
| qcom,vdd-io-voltage-level = <1800000 1800000>; |
| qcom,vdd-io-current-level = <200 325000>; |
| |
| qcom,core_3_0v_support; |
| qcom,nonremovable; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on |
| &sdc2_wlan_gpio_active>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off |
| &sdc2_wlan_gpio_sleep>; |
| |
| #address-cells = <0>; |
| interrupt-parent = <&sdhc_2>; |
| interrupts = <0 1 2>; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0xffffffff>; |
| interrupt-map = <0 &intc 0 125 0 |
| 1 &intc 0 221 0 |
| 2 &tlmm 124 0x4>; |
| interrupt-names = "hc_irq", "pwr_irq", "sdiowakeup_irq"; |
| |
| /delete-property/cd-gpios; |
| /delete-property/qcom,devfreq,freq-table; |
| |
| status = "ok"; |
| |
| }; |
| |
| &mdss_fb0 { |
| /delete-node/ qcom,cont-splash-memory; |
| }; |
| |
| /delete-node/ &cont_splash_mem; |
| |
| &soc { |
| gpio_keys { |
| /delete-node/ home; |
| }; |
| }; |
| |
| &usb_otg { |
| vbus_otg-supply = <0>; |
| qcom,vbus-low-as-hostmode; |
| }; |
| |
| &i2c_4 { |
| usb2533@2c { |
| status = "ok"; |
| }; |
| }; |
| |
| &i2c_2 { |
| /* DSI_TO_HDMI I2C configuration */ |
| adv7533@39 { |
| compatible = "adv7533"; |
| reg = <0x39>; |
| instance_id = <0>; |
| adi,video-mode = <3>; /* 3 = 1080p */ |
| adi,main-addr = <0x39>; |
| adi,cec-dsi-addr = <0x3C>; |
| adi,enable-audio; |
| adi,irq-gpio = <&tlmm 0x29 0x2002>; |
| adi,power-down-gpio = <&tlmm 0x7D 0x0>; |
| adi,switch-gpio = <&pm8937_gpios 0x8 0x1>; |
| pinctrl-names = "pmx_adv7533_active", |
| "pmx_adv7533_suspend"; |
| pinctrl-0 = <&adv7533_int_active>; |
| pinctrl-1 = <&adv7533_int_suspend>; |
| }; |
| |
| pericom-type-c@1d { |
| status = "disabled"; |
| }; |
| }; |
| |
| &mdss_dsi { |
| hw-config = "single_dsi"; |
| }; |
| |
| &mdss_dsi0 { |
| qcom,dsi-pref-prim-pan = <&dsi_adv7533_1080p>; |
| qcom,platform-intf-mux-gpio = <&tlmm 115 0>; |
| status = "ok"; |
| qcom,bridge-index = <0>; |
| qcom,pluggable; |
| }; |
| |
| &dsi_adv7533_1080p { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| }; |
| |
| &modem_mem { |
| reg = <0x0 0x86800000 0x0 0x1500000>; |
| }; |
| |
| &adsp_fw_mem { |
| reg = <0x0 0x87d00000 0x0 0x1100000>; |
| }; |
| |
| &wcnss_fw_mem { |
| reg = <0x0 0x88e00000 0x0 0x700000>; |
| }; |
| |
| &other_ext_mem { |
| reg = <0x0 0x84f00000 0x0 0x1900000>; |
| }; |
| |
| &qcom_seecom { |
| reg = <0x84f00000 0x1400000>; |
| }; |
| |
| &secure_mem { |
| status = "disabled"; |
| }; |
| |
| /* Warning, SPI6 & I2C6 cannot be enabled at the same time due to pin usage. */ |
| &spi_6 { |
| status = "disabled"; |
| }; |
| |
| &i2c_6 { |
| status = "ok"; |
| qcom,clk-freq-out = <100000>; |
| |
| /* TI591XX LED Drivers */ |
| tlc59116@60 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "ti,tlc59116"; |
| reg = <0x60>; |
| out0@0 { |
| label = "ledsec1_g"; |
| reg = <0x0>; |
| }; |
| out1@1 { |
| label = "ledsec1_r"; |
| reg = <0x1>; |
| }; |
| out2@2 { |
| label = "ledsec1_b"; |
| reg = <0x2>; |
| }; |
| out3@3 { |
| label = "ledsec2_g"; |
| reg = <0x3>; |
| }; |
| out4@4 { |
| label = "ledsec2_r"; |
| reg = <0x4>; |
| }; |
| out5@5 { |
| label = "ledsec2_b"; |
| reg = <0x5>; |
| }; |
| out6@6 { |
| label = "ledsec3_g"; |
| reg = <0x6>; |
| }; |
| out7@7 { |
| label = "ledsec3_r"; |
| reg = <0x7>; |
| }; |
| out8@8 { |
| label = "ledsec3_b"; |
| reg = <0x8>; |
| }; |
| out9@9 { |
| label = "ledsec4_g"; |
| reg = <0x9>; |
| }; |
| out10@10 { |
| label = "ledsec4_r"; |
| reg = <0xa>; |
| }; |
| out11@11 { |
| label = "ledsec4_b"; |
| reg = <0xb>; |
| }; |
| out12@12 { |
| label = "ledsec5_g"; |
| reg = <0xc>; |
| }; |
| out13@13 { |
| label = "ledsec5_r"; |
| reg = <0xd>; |
| }; |
| out14@14 { |
| label = "ledsec5_b"; |
| reg = <0xe>; |
| }; |
| }; |
| |
| tlc59116@61 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "ti,tlc59116"; |
| reg = <0x61>; |
| out0@0 { |
| label = "ledsec6_g"; |
| reg = <0x0>; |
| }; |
| out1@1 { |
| label = "ledsec6_r"; |
| reg = <0x1>; |
| }; |
| out2@2 { |
| label = "ledsec6_b"; |
| reg = <0x2>; |
| }; |
| out3@3 { |
| label = "ledsec7_g"; |
| reg = <0x3>; |
| }; |
| out4@4 { |
| label = "ledsec7_r"; |
| reg = <0x4>; |
| }; |
| out5@5 { |
| label = "ledsec7_b"; |
| reg = <0x5>; |
| }; |
| out6@6 { |
| label = "ledsec8_g"; |
| reg = <0x6>; |
| }; |
| out7@7 { |
| label = "ledsec8_r"; |
| reg = <0x7>; |
| }; |
| out8@8 { |
| label = "ledsec8_b"; |
| reg = <0x8>; |
| }; |
| out9@9 { |
| label = "ledsec9_g"; |
| reg = <0x9>; |
| }; |
| out10@10 { |
| label = "ledsec9_r"; |
| reg = <0xa>; |
| }; |
| out11@11 { |
| label = "ledsec9_b"; |
| reg = <0xb>; |
| }; |
| }; |
| }; |
| |
| &soc { |
| pinctrl@1000000 { |
| i2c6{ |
| tlc59116_reset: tlc59116_reset { |
| config { |
| pins = "gpio20"; |
| drive-strength = <16>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| }; |
| }; |