| Qualcomm Technologies, Inc. |
| |
| mdss-dsi is the master DSI device which supports multiple DSI host controllers |
| that are compatible with MIPI display serial interface specification. |
| |
| DSI Controller: |
| Required properties: |
| - compatible: Should be "qcom,dsi-ctrl-hw-v<version>". Supported |
| versions include 1.4, 2.0 and 2.2. |
| eg: qcom,dsi-ctrl-hw-v1.4, qcom,dsi-ctrl-hw-v2.0, |
| qcom,dsi-ctrl-hw-v2.2 |
| And for dsi phy driver: |
| qcom,dsi-phy-v0.0-hpm, qcom,dsi-phy-v0.0-lpm, |
| qcom,dsi-phy-v1.0, qcom,dsi-phy-v2.0, |
| qcom,dsi-phy-v3.0 |
| - reg: Base address and length of DSI controller's memory |
| mapped regions. |
| - reg-names: A list of strings that name the list of regs. |
| "dsi_ctrl" - DSI controller memory region. |
| "mmss_misc" - MMSS misc memory region. |
| - cell-index: Specifies the controller instance. |
| - clocks: Clocks required for DSI controller operation. |
| - clock-names: Names of the clocks corresponding to handles. Following |
| clocks are required: |
| "mdp_core_clk" |
| "iface_clk" |
| "core_mmss_clk" |
| "bus_clk" |
| "byte_clk" |
| "pixel_clk" |
| "core_clk" |
| "byte_clk_rcg" |
| "pixel_clk_rcg" |
| - gdsc-supply: phandle to gdsc regulator node. |
| - vdda-supply: phandle to vdda regulator node. |
| - vcca-supply: phandle to vcca regulator node. |
| - interrupt-parent phandle to the interrupt parent device node. |
| - interrupts: The interrupt signal from the DSI block. |
| |
| Bus Scaling Data: |
| - qcom,msm-bus,name: String property describing MDSS client. |
| - qcom,msm-bus,num-cases: This is the number of bus scaling use cases |
| defined in the vectors property. This must be |
| set to <2> for MDSS DSI driver where use-case 0 |
| is used to remove BW votes from the system. Use |
| case 1 is used to generate bandwidth requestes |
| when sending command packets. |
| - qcom,msm-bus,num-paths: This represents number of paths in each bus |
| scaling usecase. This value depends on number of |
| AXI master ports dedicated to MDSS for |
| particular chipset. |
| - qcom,msm-bus,vectors-KBps: A series of 4 cell properties, with a format |
| of (src, dst, ab, ib) which is defined at |
| Documentation/devicetree/bindings/arm/msm/msm_bus.txt. |
| DSI driver should always set average bandwidth |
| (ab) to 0 and always use instantaneous |
| bandwidth(ib) values. |
| |
| Optional properties: |
| - label: String to describe controller. |
| - qcom,platform-te-gpio: Specifies the gpio used for TE. |
| - qcom,dsi-display-active: Current active display |
| - qcom,dsi-ctrl: handle to dsi controller device |
| - qcom,dsi-phy: handle to dsi phy device |
| - qcom,dsi-manager: Specifies dsi manager is present |
| - qcom,dsi-display: Specifies dsi display is present |
| - qcom,hdmi-display: Specifies hdmi is present |
| - qcom,dp-display: Specified dp is present |
| - qcom,<type>-supply-entries: A node that lists the elements of the supply used by the |
| a particular "type" of DSI module. The module "types" |
| can be "core", "ctrl", and "phy". Within the same type, |
| there can be more than one instance of this binding, |
| in which case the entry would be appended with the |
| supply entry index. |
| e.g. qcom,ctrl-supply-entry@0 |
| -- qcom,supply-name: name of the supply (vdd/vdda/vddio) |
| -- qcom,supply-min-voltage: minimum voltage level (uV) |
| -- qcom,supply-max-voltage: maximum voltage level (uV) |
| -- qcom,supply-enable-load: load drawn (uA) from enabled supply |
| -- qcom,supply-disable-load: load drawn (uA) from disabled supply |
| -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on |
| -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on |
| -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off |
| -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off |
| - qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode |
| panels in microseconds. Driver uses this number to adjust |
| the clock rate according to the expected transfer time. |
| Increasing this value would slow down the mdp processing |
| and can result in slower performance. |
| Decreasing this value can speed up the mdp processing, |
| but this can also impact power consumption. |
| As a rule this time should not be higher than the time |
| that would be expected with the processing at the |
| dsi link rate since anyways this would be the maximum |
| transfer time that could be achieved. |
| If ping pong split enabled, this time should not be higher |
| than two times the dsi link rate time. |
| If the property is not specified, then the default value is 14000 us. |