| /* Copyright (c) 2012-2015, 2017, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/regmap.h> |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/leds.h> |
| #include <linux/err.h> |
| #include <linux/spinlock.h> |
| #include <linux/of_platform.h> |
| #include <linux/of_device.h> |
| #include <linux/spmi.h> |
| #include <linux/platform_device.h> |
| #include <linux/qpnp/pwm.h> |
| #include <linux/workqueue.h> |
| #include <linux/delay.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/delay.h> |
| |
| #define WLED_MOD_EN_REG(base, n) (base + 0x60 + n*0x10) |
| #define WLED_IDAC_DLY_REG(base, n) (WLED_MOD_EN_REG(base, n) + 0x01) |
| #define WLED_FULL_SCALE_REG(base, n) (WLED_IDAC_DLY_REG(base, n) + 0x01) |
| #define WLED_MOD_SRC_SEL_REG(base, n) (WLED_FULL_SCALE_REG(base, n) + 0x01) |
| |
| /* wled control registers */ |
| #define WLED_OVP_INT_STATUS(base) (base + 0x10) |
| #define WLED_BRIGHTNESS_CNTL_LSB(base, n) (base + 0x40 + 2*n) |
| #define WLED_BRIGHTNESS_CNTL_MSB(base, n) (base + 0x41 + 2*n) |
| #define WLED_MOD_CTRL_REG(base) (base + 0x46) |
| #define WLED_SYNC_REG(base) (base + 0x47) |
| #define WLED_FDBCK_CTRL_REG(base) (base + 0x48) |
| #define WLED_SWITCHING_FREQ_REG(base) (base + 0x4C) |
| #define WLED_OVP_CFG_REG(base) (base + 0x4D) |
| #define WLED_BOOST_LIMIT_REG(base) (base + 0x4E) |
| #define WLED_CURR_SINK_REG(base) (base + 0x4F) |
| #define WLED_HIGH_POLE_CAP_REG(base) (base + 0x58) |
| #define WLED_CURR_SINK_MASK 0xE0 |
| #define WLED_CURR_SINK_SHFT 0x05 |
| #define WLED_DISABLE_ALL_SINKS 0x00 |
| #define WLED_DISABLE_1_2_SINKS 0x80 |
| #define WLED_SWITCH_FREQ_MASK 0x0F |
| #define WLED_OVP_VAL_MASK 0x03 |
| #define WLED_OVP_INT_MASK 0x02 |
| #define WLED_OVP_VAL_BIT_SHFT 0x00 |
| #define WLED_BOOST_LIMIT_MASK 0x07 |
| #define WLED_BOOST_LIMIT_BIT_SHFT 0x00 |
| #define WLED_BOOST_ON 0x80 |
| #define WLED_BOOST_OFF 0x00 |
| #define WLED_EN_MASK 0x80 |
| #define WLED_NO_MASK 0x00 |
| #define WLED_CP_SELECT_MAX 0x03 |
| #define WLED_CP_SELECT_MASK 0x02 |
| #define WLED_USE_EXT_GEN_MOD_SRC 0x01 |
| #define WLED_CTL_DLY_STEP 200 |
| #define WLED_CTL_DLY_MAX 1400 |
| #define WLED_MAX_CURR 25 |
| #define WLED_NO_CURRENT 0x00 |
| #define WLED_OVP_DELAY 1000 |
| #define WLED_OVP_DELAY_INT 200 |
| #define WLED_OVP_DELAY_LOOP 100 |
| #define WLED_MSB_MASK 0x0F |
| #define WLED_MAX_CURR_MASK 0x1F |
| #define WLED_OP_FDBCK_MASK 0x07 |
| #define WLED_OP_FDBCK_BIT_SHFT 0x00 |
| #define WLED_OP_FDBCK_DEFAULT 0x00 |
| |
| #define WLED_SET_ILIM_CODE 0x01 |
| |
| #define WLED_MAX_LEVEL 4095 |
| #define WLED_8_BIT_MASK 0xFF |
| #define WLED_4_BIT_MASK 0x0F |
| #define WLED_8_BIT_SHFT 0x08 |
| #define WLED_MAX_DUTY_CYCLE 0xFFF |
| |
| #define WLED_SYNC_VAL 0x07 |
| #define WLED_SYNC_RESET_VAL 0x00 |
| |
| #define PMIC_VER_8026 0x04 |
| #define PMIC_VER_8941 0x01 |
| #define PMIC_VERSION_REG 0x0105 |
| |
| #define WLED_DEFAULT_STRINGS 0x01 |
| #define WLED_THREE_STRINGS 0x03 |
| #define WLED_MAX_TRIES 5 |
| #define WLED_DEFAULT_OVP_VAL 0x02 |
| #define WLED_BOOST_LIM_DEFAULT 0x03 |
| #define WLED_CP_SEL_DEFAULT 0x00 |
| #define WLED_CTRL_DLY_DEFAULT 0x00 |
| #define WLED_SWITCH_FREQ_DEFAULT 0x0B |
| |
| #define FLASH_SAFETY_TIMER(base) (base + 0x40) |
| #define FLASH_MAX_CURR(base) (base + 0x41) |
| #define FLASH_LED_0_CURR(base) (base + 0x42) |
| #define FLASH_LED_1_CURR(base) (base + 0x43) |
| #define FLASH_CLAMP_CURR(base) (base + 0x44) |
| #define FLASH_LED_TMR_CTRL(base) (base + 0x48) |
| #define FLASH_HEADROOM(base) (base + 0x4A) |
| #define FLASH_STARTUP_DELAY(base) (base + 0x4B) |
| #define FLASH_MASK_ENABLE(base) (base + 0x4C) |
| #define FLASH_VREG_OK_FORCE(base) (base + 0x4F) |
| #define FLASH_ENABLE_CONTROL(base) (base + 0x46) |
| #define FLASH_LED_STROBE_CTRL(base) (base + 0x47) |
| #define FLASH_WATCHDOG_TMR(base) (base + 0x49) |
| #define FLASH_FAULT_DETECT(base) (base + 0x51) |
| #define FLASH_PERIPHERAL_SUBTYPE(base) (base + 0x05) |
| #define FLASH_CURRENT_RAMP(base) (base + 0x54) |
| |
| #define FLASH_MAX_LEVEL 0x4F |
| #define TORCH_MAX_LEVEL 0x0F |
| #define FLASH_NO_MASK 0x00 |
| |
| #define FLASH_MASK_1 0x20 |
| #define FLASH_MASK_REG_MASK 0xE0 |
| #define FLASH_HEADROOM_MASK 0x03 |
| #define FLASH_SAFETY_TIMER_MASK 0x7F |
| #define FLASH_CURRENT_MASK 0xFF |
| #define FLASH_MAX_CURRENT_MASK 0x7F |
| #define FLASH_TMR_MASK 0x03 |
| #define FLASH_TMR_WATCHDOG 0x03 |
| #define FLASH_TMR_SAFETY 0x00 |
| #define FLASH_FAULT_DETECT_MASK 0X80 |
| #define FLASH_HW_VREG_OK 0x40 |
| #define FLASH_SW_VREG_OK 0x80 |
| #define FLASH_VREG_MASK 0xC0 |
| #define FLASH_STARTUP_DLY_MASK 0x02 |
| #define FLASH_CURRENT_RAMP_MASK 0xBF |
| |
| #define FLASH_ENABLE_ALL 0xE0 |
| #define FLASH_ENABLE_MODULE 0x80 |
| #define FLASH_ENABLE_MODULE_MASK 0x80 |
| #define FLASH_DISABLE_ALL 0x00 |
| #define FLASH_ENABLE_MASK 0xE0 |
| #define FLASH_ENABLE_LED_0 0xC0 |
| #define FLASH_ENABLE_LED_1 0xA0 |
| #define FLASH_INIT_MASK 0xE0 |
| #define FLASH_SELFCHECK_ENABLE 0x80 |
| #define FLASH_WATCHDOG_MASK 0x1F |
| #define FLASH_RAMP_STEP_27US 0xBF |
| |
| #define FLASH_HW_SW_STROBE_SEL_MASK 0x04 |
| #define FLASH_STROBE_MASK 0xC7 |
| #define FLASH_LED_0_OUTPUT 0x80 |
| #define FLASH_LED_1_OUTPUT 0x40 |
| #define FLASH_TORCH_OUTPUT 0xC0 |
| |
| #define FLASH_CURRENT_PRGM_MIN 1 |
| #define FLASH_CURRENT_PRGM_SHIFT 1 |
| #define FLASH_CURRENT_MAX 0x4F |
| #define FLASH_CURRENT_TORCH 0x07 |
| |
| #define FLASH_DURATION_200ms 0x13 |
| #define TORCH_DURATION_12s 0x0A |
| #define FLASH_CLAMP_200mA 0x0F |
| |
| #define FLASH_SUBTYPE_DUAL 0x01 |
| #define FLASH_SUBTYPE_SINGLE 0x02 |
| |
| #define FLASH_RAMP_UP_DELAY_US 1000 |
| #define FLASH_RAMP_DN_DELAY_US 2160 |
| |
| #define LED_TRIGGER_DEFAULT "none" |
| |
| #define RGB_LED_SRC_SEL(base) (base + 0x45) |
| #define RGB_LED_EN_CTL(base) (base + 0x46) |
| #define RGB_LED_ATC_CTL(base) (base + 0x47) |
| |
| #define RGB_MAX_LEVEL LED_FULL |
| #define RGB_LED_ENABLE_RED 0x80 |
| #define RGB_LED_ENABLE_GREEN 0x40 |
| #define RGB_LED_ENABLE_BLUE 0x20 |
| #define RGB_LED_SOURCE_VPH_PWR 0x01 |
| #define RGB_LED_ENABLE_MASK 0xE0 |
| #define RGB_LED_SRC_MASK 0x03 |
| #define QPNP_LED_PWM_FLAGS (PM_PWM_LUT_LOOP | PM_PWM_LUT_RAMP_UP) |
| #define QPNP_LUT_RAMP_STEP_DEFAULT 255 |
| #define PWM_LUT_MAX_SIZE 63 |
| #define PWM_GPLED_LUT_MAX_SIZE 31 |
| #define RGB_LED_DISABLE 0x00 |
| |
| #define MPP_MAX_LEVEL LED_FULL |
| #define LED_MPP_MODE_CTRL(base) (base + 0x40) |
| #define LED_MPP_VIN_CTRL(base) (base + 0x41) |
| #define LED_MPP_EN_CTRL(base) (base + 0x46) |
| #define LED_MPP_SINK_CTRL(base) (base + 0x4C) |
| |
| #define LED_MPP_CURRENT_MIN 5 |
| #define LED_MPP_CURRENT_MAX 40 |
| #define LED_MPP_VIN_CTRL_DEFAULT 0 |
| #define LED_MPP_CURRENT_PER_SETTING 5 |
| #define LED_MPP_SOURCE_SEL_DEFAULT LED_MPP_MODE_ENABLE |
| |
| #define LED_MPP_SINK_MASK 0x07 |
| #define LED_MPP_MODE_MASK 0x7F |
| #define LED_MPP_VIN_MASK 0x03 |
| #define LED_MPP_EN_MASK 0x80 |
| #define LED_MPP_SRC_MASK 0x0F |
| #define LED_MPP_MODE_CTRL_MASK 0x70 |
| |
| #define LED_MPP_MODE_SINK (0x06 << 4) |
| #define LED_MPP_MODE_ENABLE 0x01 |
| #define LED_MPP_MODE_OUTPUT 0x10 |
| #define LED_MPP_MODE_DISABLE 0x00 |
| #define LED_MPP_EN_ENABLE 0x80 |
| #define LED_MPP_EN_DISABLE 0x00 |
| |
| #define MPP_SOURCE_DTEST1 0x08 |
| |
| #define GPIO_MAX_LEVEL LED_FULL |
| #define LED_GPIO_MODE_CTRL(base) (base + 0x40) |
| #define LED_GPIO_VIN_CTRL(base) (base + 0x41) |
| #define LED_GPIO_EN_CTRL(base) (base + 0x46) |
| |
| #define LED_GPIO_VIN_CTRL_DEFAULT 0 |
| #define LED_GPIO_SOURCE_SEL_DEFAULT LED_GPIO_MODE_ENABLE |
| |
| #define LED_GPIO_MODE_MASK 0x3F |
| #define LED_GPIO_VIN_MASK 0x0F |
| #define LED_GPIO_EN_MASK 0x80 |
| #define LED_GPIO_SRC_MASK 0x0F |
| #define LED_GPIO_MODE_CTRL_MASK 0x30 |
| |
| #define LED_GPIO_MODE_ENABLE 0x01 |
| #define LED_GPIO_MODE_DISABLE 0x00 |
| #define LED_GPIO_MODE_OUTPUT 0x10 |
| #define LED_GPIO_EN_ENABLE 0x80 |
| #define LED_GPIO_EN_DISABLE 0x00 |
| |
| #define KPDBL_MAX_LEVEL LED_FULL |
| #define KPDBL_ROW_SRC_SEL(base) (base + 0x40) |
| #define KPDBL_ENABLE(base) (base + 0x46) |
| #define KPDBL_ROW_SRC(base) (base + 0xE5) |
| |
| #define KPDBL_ROW_SRC_SEL_VAL_MASK 0x0F |
| #define KPDBL_ROW_SCAN_EN_MASK 0x80 |
| #define KPDBL_ROW_SCAN_VAL_MASK 0x0F |
| #define KPDBL_ROW_SCAN_EN_SHIFT 7 |
| #define KPDBL_MODULE_EN 0x80 |
| #define KPDBL_MODULE_DIS 0x00 |
| #define KPDBL_MODULE_EN_MASK 0x80 |
| #define NUM_KPDBL_LEDS 4 |
| #define KPDBL_MASTER_BIT_INDEX 0 |
| |
| /** |
| * enum qpnp_leds - QPNP supported led ids |
| * @QPNP_ID_WLED - White led backlight |
| */ |
| enum qpnp_leds { |
| QPNP_ID_WLED = 0, |
| QPNP_ID_FLASH1_LED0, |
| QPNP_ID_FLASH1_LED1, |
| QPNP_ID_RGB_RED, |
| QPNP_ID_RGB_GREEN, |
| QPNP_ID_RGB_BLUE, |
| QPNP_ID_LED_MPP, |
| QPNP_ID_KPDBL, |
| QPNP_ID_LED_GPIO, |
| QPNP_ID_MAX, |
| }; |
| |
| /* current boost limit */ |
| enum wled_current_boost_limit { |
| WLED_CURR_LIMIT_105mA, |
| WLED_CURR_LIMIT_385mA, |
| WLED_CURR_LIMIT_525mA, |
| WLED_CURR_LIMIT_805mA, |
| WLED_CURR_LIMIT_980mA, |
| WLED_CURR_LIMIT_1260mA, |
| WLED_CURR_LIMIT_1400mA, |
| WLED_CURR_LIMIT_1680mA, |
| }; |
| |
| /* over voltage protection threshold */ |
| enum wled_ovp_threshold { |
| WLED_OVP_35V, |
| WLED_OVP_32V, |
| WLED_OVP_29V, |
| WLED_OVP_27V, |
| }; |
| |
| enum flash_headroom { |
| HEADROOM_250mV = 0, |
| HEADROOM_300mV, |
| HEADROOM_400mV, |
| HEADROOM_500mV, |
| }; |
| |
| enum flash_startup_dly { |
| DELAY_10us = 0, |
| DELAY_32us, |
| DELAY_64us, |
| DELAY_128us, |
| }; |
| |
| enum led_mode { |
| PWM_MODE = 0, |
| LPG_MODE, |
| MANUAL_MODE, |
| }; |
| |
| static u8 wled_debug_regs[] = { |
| /* brightness registers */ |
| 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, |
| /* common registers */ |
| 0x46, 0x47, 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, |
| 0x50, 0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57, 0x58, 0x59, |
| /* LED1 */ |
| 0x60, 0x61, 0x62, 0x63, 0x66, |
| /* LED2 */ |
| 0x70, 0x71, 0x72, 0x73, 0x76, |
| /* LED3 */ |
| 0x80, 0x81, 0x82, 0x83, 0x86, |
| }; |
| |
| static u8 flash_debug_regs[] = { |
| 0x40, 0x41, 0x42, 0x43, 0x44, 0x48, 0x49, 0x4b, 0x4c, |
| 0x4f, 0x46, 0x47, |
| }; |
| |
| static u8 rgb_pwm_debug_regs[] = { |
| 0x45, 0x46, 0x47, |
| }; |
| |
| static u8 mpp_debug_regs[] = { |
| 0x40, 0x41, 0x42, 0x45, 0x46, 0x4c, |
| }; |
| |
| static u8 kpdbl_debug_regs[] = { |
| 0x40, 0x46, 0xb1, 0xb3, 0xb4, 0xe5, |
| }; |
| |
| static u8 gpio_debug_regs[] = { |
| 0x40, 0x41, 0x42, 0x45, 0x46, |
| }; |
| |
| /** |
| * pwm_config_data - pwm configuration data |
| * @lut_params - lut parameters to be used by pwm driver |
| * @pwm_device - pwm device |
| * @pwm_period_us - period for pwm, in us |
| * @mode - mode the led operates in |
| * @old_duty_pcts - storage for duty pcts that may need to be reused |
| * @default_mode - default mode of LED as set in device tree |
| * @use_blink - use blink sysfs entry |
| * @blinking - device is currently blinking w/LPG mode |
| */ |
| struct pwm_config_data { |
| struct lut_params lut_params; |
| struct pwm_device *pwm_dev; |
| u32 pwm_period_us; |
| struct pwm_duty_cycles *duty_cycles; |
| int *old_duty_pcts; |
| u8 mode; |
| u8 default_mode; |
| bool pwm_enabled; |
| bool use_blink; |
| bool blinking; |
| }; |
| |
| /** |
| * wled_config_data - wled configuration data |
| * @num_strings - number of wled strings to be configured |
| * @num_physical_strings - physical number of strings supported |
| * @ovp_val - over voltage protection threshold |
| * @boost_curr_lim - boot current limit |
| * @cp_select - high pole capacitance |
| * @ctrl_delay_us - delay in activation of led |
| * @dig_mod_gen_en - digital module generator |
| * @cs_out_en - current sink output enable |
| * @op_fdbck - selection of output as feedback for the boost |
| */ |
| struct wled_config_data { |
| u8 num_strings; |
| u8 num_physical_strings; |
| u8 ovp_val; |
| u8 boost_curr_lim; |
| u8 cp_select; |
| u8 ctrl_delay_us; |
| u8 switch_freq; |
| u8 op_fdbck; |
| u8 pmic_version; |
| bool dig_mod_gen_en; |
| bool cs_out_en; |
| }; |
| |
| /** |
| * mpp_config_data - mpp configuration data |
| * @pwm_cfg - device pwm configuration |
| * @current_setting - current setting, 5ma-40ma in 5ma increments |
| * @source_sel - source selection |
| * @mode_ctrl - mode control |
| * @vin_ctrl - input control |
| * @min_brightness - minimum brightness supported |
| * @pwm_mode - pwm mode in use |
| * @max_uV - maximum regulator voltage |
| * @min_uV - minimum regulator voltage |
| * @mpp_reg - regulator to power mpp based LED |
| * @enable - flag indicating LED on or off |
| */ |
| struct mpp_config_data { |
| struct pwm_config_data *pwm_cfg; |
| u8 current_setting; |
| u8 source_sel; |
| u8 mode_ctrl; |
| u8 vin_ctrl; |
| u8 min_brightness; |
| u8 pwm_mode; |
| u32 max_uV; |
| u32 min_uV; |
| struct regulator *mpp_reg; |
| bool enable; |
| }; |
| |
| /** |
| * flash_config_data - flash configuration data |
| * @current_prgm - current to be programmed, scaled by max level |
| * @clamp_curr - clamp current to use |
| * @headroom - headroom value to use |
| * @duration - duration of the flash |
| * @enable_module - enable address for particular flash |
| * @trigger_flash - trigger flash |
| * @startup_dly - startup delay for flash |
| * @strobe_type - select between sw and hw strobe |
| * @peripheral_subtype - module peripheral subtype |
| * @current_addr - address to write for current |
| * @second_addr - address of secondary flash to be written |
| * @safety_timer - enable safety timer or watchdog timer |
| * @torch_enable - enable flash LED torch mode |
| * @flash_reg_get - flash regulator attached or not |
| * @flash_wa_reg_get - workaround regulator attached or not |
| * @flash_on - flash status, on or off |
| * @torch_on - torch status, on or off |
| * @vreg_ok - specifies strobe type, sw or hw |
| * @no_smbb_support - specifies if smbb boost is not required and there is a |
| single regulator for both flash and torch |
| * @flash_boost_reg - boost regulator for flash |
| * @torch_boost_reg - boost regulator for torch |
| * @flash_wa_reg - flash regulator for wa |
| */ |
| struct flash_config_data { |
| u8 current_prgm; |
| u8 clamp_curr; |
| u8 headroom; |
| u8 duration; |
| u8 enable_module; |
| u8 trigger_flash; |
| u8 startup_dly; |
| u8 strobe_type; |
| u8 peripheral_subtype; |
| u16 current_addr; |
| u16 second_addr; |
| bool safety_timer; |
| bool torch_enable; |
| bool flash_reg_get; |
| bool flash_wa_reg_get; |
| bool flash_on; |
| bool torch_on; |
| bool vreg_ok; |
| bool no_smbb_support; |
| struct regulator *flash_boost_reg; |
| struct regulator *torch_boost_reg; |
| struct regulator *flash_wa_reg; |
| }; |
| |
| /** |
| * kpdbl_config_data - kpdbl configuration data |
| * @pwm_cfg - device pwm configuration |
| * @mode - running mode: pwm or lut |
| * @row_id - row id of the led |
| * @row_src_vbst - 0 for vph_pwr and 1 for vbst |
| * @row_src_en - enable row source |
| * @always_on - always on row |
| * @lut_params - lut parameters to be used by pwm driver |
| * @duty_cycles - duty cycles for lut |
| * @pwm_mode - pwm mode in use |
| */ |
| struct kpdbl_config_data { |
| struct pwm_config_data *pwm_cfg; |
| u32 row_id; |
| bool row_src_vbst; |
| bool row_src_en; |
| bool always_on; |
| struct pwm_duty_cycles *duty_cycles; |
| struct lut_params lut_params; |
| u8 pwm_mode; |
| }; |
| |
| /** |
| * rgb_config_data - rgb configuration data |
| * @pwm_cfg - device pwm configuration |
| * @enable - bits to enable led |
| */ |
| struct rgb_config_data { |
| struct pwm_config_data *pwm_cfg; |
| u8 enable; |
| }; |
| |
| /** |
| * gpio_config_data - gpio configuration data |
| * @source_sel - source selection |
| * @mode_ctrl - mode control |
| * @vin_ctrl - input control |
| * @enable - flag indicating LED on or off |
| */ |
| struct gpio_config_data { |
| u8 source_sel; |
| u8 mode_ctrl; |
| u8 vin_ctrl; |
| bool enable; |
| }; |
| |
| /** |
| * struct qpnp_led_data - internal led data structure |
| * @led_classdev - led class device |
| * @delayed_work - delayed work for turning off the LED |
| * @workqueue - dedicated workqueue to handle concurrency |
| * @work - workqueue for led |
| * @id - led index |
| * @base_reg - base register given in device tree |
| * @lock - to protect the transactions |
| * @reg - cached value of led register |
| * @num_leds - number of leds in the module |
| * @max_current - maximum current supported by LED |
| * @default_on - true: default state max, false, default state 0 |
| * @turn_off_delay_ms - number of msec before turning off the LED |
| */ |
| struct qpnp_led_data { |
| struct led_classdev cdev; |
| struct platform_device *pdev; |
| struct regmap *regmap; |
| struct delayed_work dwork; |
| struct workqueue_struct *workqueue; |
| struct work_struct work; |
| int id; |
| u16 base; |
| u8 reg; |
| u8 num_leds; |
| struct mutex lock; |
| struct wled_config_data *wled_cfg; |
| struct flash_config_data *flash_cfg; |
| struct kpdbl_config_data *kpdbl_cfg; |
| struct rgb_config_data *rgb_cfg; |
| struct mpp_config_data *mpp_cfg; |
| struct gpio_config_data *gpio_cfg; |
| int max_current; |
| bool default_on; |
| bool in_order_command_processing; |
| int turn_off_delay_ms; |
| }; |
| |
| static DEFINE_MUTEX(flash_lock); |
| static struct pwm_device *kpdbl_master; |
| static u32 kpdbl_master_period_us; |
| DECLARE_BITMAP(kpdbl_leds_in_use, NUM_KPDBL_LEDS); |
| static bool is_kpdbl_master_turn_on; |
| |
| static int |
| qpnp_led_masked_write(struct qpnp_led_data *led, u16 addr, u8 mask, u8 val) |
| { |
| int rc; |
| |
| rc = regmap_update_bits(led->regmap, addr, mask, val); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "Unable to regmap_update_bits to addr=%x, rc(%d)\n", |
| addr, rc); |
| return rc; |
| } |
| |
| static void qpnp_dump_regs(struct qpnp_led_data *led, u8 regs[], u8 array_size) |
| { |
| int i; |
| u8 val; |
| |
| pr_debug("===== %s LED register dump start =====\n", led->cdev.name); |
| for (i = 0; i < array_size; i++) { |
| regmap_bulk_read(led->regmap, led->base + regs[i], &val, |
| sizeof(val)); |
| pr_debug("%s: 0x%x = 0x%x\n", led->cdev.name, |
| led->base + regs[i], val); |
| } |
| pr_debug("===== %s LED register dump end =====\n", led->cdev.name); |
| } |
| |
| static int qpnp_wled_sync(struct qpnp_led_data *led) |
| { |
| int rc; |
| u8 val; |
| |
| /* sync */ |
| val = WLED_SYNC_VAL; |
| rc = regmap_write(led->regmap, WLED_SYNC_REG(led->base), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED set sync reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| val = WLED_SYNC_RESET_VAL; |
| rc = regmap_write(led->regmap, WLED_SYNC_REG(led->base), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED reset sync reg failed(%d)\n", rc); |
| return rc; |
| } |
| return 0; |
| } |
| |
| static int qpnp_wled_set(struct qpnp_led_data *led) |
| { |
| int rc, duty, level, tries = 0; |
| u8 val, i, num_wled_strings; |
| uint sink_val, ilim_val, ovp_val; |
| |
| num_wled_strings = led->wled_cfg->num_strings; |
| |
| level = led->cdev.brightness; |
| |
| if (level > WLED_MAX_LEVEL) |
| level = WLED_MAX_LEVEL; |
| if (level == 0) { |
| for (i = 0; i < num_wled_strings; i++) { |
| rc = qpnp_led_masked_write(led, |
| WLED_FULL_SCALE_REG(led->base, i), |
| WLED_MAX_CURR_MASK, WLED_NO_CURRENT); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Write max current failure (%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| rc = qpnp_wled_sync(led); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED sync failed(%d)\n", rc); |
| return rc; |
| } |
| |
| rc = regmap_read(led->regmap, WLED_CURR_SINK_REG(led->base), |
| &sink_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED read sink reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| if (led->wled_cfg->pmic_version == PMIC_VER_8026) { |
| val = WLED_DISABLE_ALL_SINKS; |
| rc = regmap_write(led->regmap, |
| WLED_CURR_SINK_REG(led->base), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| usleep_range(WLED_OVP_DELAY, WLED_OVP_DELAY + 10); |
| } else if (led->wled_cfg->pmic_version == PMIC_VER_8941) { |
| if (led->wled_cfg->num_physical_strings <= |
| WLED_THREE_STRINGS) { |
| val = WLED_DISABLE_1_2_SINKS; |
| rc = regmap_write(led->regmap, |
| WLED_CURR_SINK_REG(led->base), |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed"); |
| return rc; |
| } |
| |
| rc = regmap_read(led->regmap, |
| WLED_BOOST_LIMIT_REG(led->base), |
| &ilim_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read boost reg"); |
| } |
| val = WLED_SET_ILIM_CODE; |
| rc = regmap_write(led->regmap, |
| WLED_BOOST_LIMIT_REG(led->base), |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed"); |
| return rc; |
| } |
| usleep_range(WLED_OVP_DELAY, |
| WLED_OVP_DELAY + 10); |
| } else { |
| val = WLED_DISABLE_ALL_SINKS; |
| rc = regmap_write(led->regmap, |
| WLED_CURR_SINK_REG(led->base), |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed"); |
| return rc; |
| } |
| |
| msleep(WLED_OVP_DELAY_INT); |
| while (tries < WLED_MAX_TRIES) { |
| rc = regmap_read(led->regmap, |
| WLED_OVP_INT_STATUS(led->base), |
| &ovp_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read boost reg"); |
| } |
| |
| if (ovp_val & WLED_OVP_INT_MASK) |
| break; |
| |
| msleep(WLED_OVP_DELAY_LOOP); |
| tries++; |
| } |
| usleep_range(WLED_OVP_DELAY, |
| WLED_OVP_DELAY + 10); |
| } |
| } |
| |
| val = WLED_BOOST_OFF; |
| rc = regmap_write(led->regmap, WLED_MOD_CTRL_REG(led->base), |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write ctrl reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| for (i = 0; i < num_wled_strings; i++) { |
| rc = qpnp_led_masked_write(led, |
| WLED_FULL_SCALE_REG(led->base, i), |
| WLED_MAX_CURR_MASK, (u8)led->max_current); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Write max current failure (%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| rc = qpnp_wled_sync(led); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED sync failed(%d)\n", rc); |
| return rc; |
| } |
| |
| if (led->wled_cfg->pmic_version == PMIC_VER_8941) { |
| if (led->wled_cfg->num_physical_strings <= |
| WLED_THREE_STRINGS) { |
| rc = regmap_write(led->regmap, |
| WLED_BOOST_LIMIT_REG(led->base), |
| ilim_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed"); |
| return rc; |
| } |
| } else { |
| /* restore OVP to original value */ |
| rc = regmap_write(led->regmap, |
| WLED_OVP_CFG_REG(led->base), |
| *&led->wled_cfg->ovp_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed"); |
| return rc; |
| } |
| } |
| } |
| |
| /* re-enable all sinks */ |
| rc = regmap_write(led->regmap, WLED_CURR_SINK_REG(led->base), |
| sink_val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write sink reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| } else { |
| val = WLED_BOOST_ON; |
| rc = regmap_write(led->regmap, WLED_MOD_CTRL_REG(led->base), |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write ctrl reg failed(%d)\n", rc); |
| return rc; |
| } |
| } |
| |
| duty = (WLED_MAX_DUTY_CYCLE * level) / WLED_MAX_LEVEL; |
| |
| /* program brightness control registers */ |
| for (i = 0; i < num_wled_strings; i++) { |
| rc = qpnp_led_masked_write(led, |
| WLED_BRIGHTNESS_CNTL_MSB(led->base, i), WLED_MSB_MASK, |
| (duty >> WLED_8_BIT_SHFT) & WLED_4_BIT_MASK); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED set brightness MSB failed(%d)\n", rc); |
| return rc; |
| } |
| val = duty & WLED_8_BIT_MASK; |
| rc = regmap_write(led->regmap, |
| WLED_BRIGHTNESS_CNTL_LSB(led->base, i), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED set brightness LSB failed(%d)\n", rc); |
| return rc; |
| } |
| } |
| |
| rc = qpnp_wled_sync(led); |
| if (rc) { |
| dev_err(&led->pdev->dev, "WLED sync failed(%d)\n", rc); |
| return rc; |
| } |
| return 0; |
| } |
| |
| static int qpnp_mpp_set(struct qpnp_led_data *led) |
| { |
| int rc; |
| u8 val; |
| int duty_us, duty_ns, period_us; |
| |
| if (led->cdev.brightness) { |
| if (led->mpp_cfg->mpp_reg && !led->mpp_cfg->enable) { |
| rc = regulator_set_voltage(led->mpp_cfg->mpp_reg, |
| led->mpp_cfg->min_uV, |
| led->mpp_cfg->max_uV); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Regulator voltage set failed rc=%d\n", |
| rc); |
| return rc; |
| } |
| |
| rc = regulator_enable(led->mpp_cfg->mpp_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Regulator enable failed(%d)\n", rc); |
| goto err_reg_enable; |
| } |
| } |
| |
| led->mpp_cfg->enable = true; |
| |
| if (led->cdev.brightness < led->mpp_cfg->min_brightness) { |
| dev_warn(&led->pdev->dev, "brightness is less than supported, set to minimum supported\n"); |
| led->cdev.brightness = led->mpp_cfg->min_brightness; |
| } |
| |
| if (led->mpp_cfg->pwm_mode != MANUAL_MODE) { |
| if (!led->mpp_cfg->pwm_cfg->blinking) { |
| led->mpp_cfg->pwm_cfg->mode = |
| led->mpp_cfg->pwm_cfg->default_mode; |
| led->mpp_cfg->pwm_mode = |
| led->mpp_cfg->pwm_cfg->default_mode; |
| } |
| } |
| if (led->mpp_cfg->pwm_mode == PWM_MODE) { |
| /*config pwm for brightness scaling*/ |
| rc = pwm_change_mode(led->mpp_cfg->pwm_cfg->pwm_dev, |
| PM_PWM_MODE_PWM); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failed to set PWM mode, rc = %d\n", |
| rc); |
| return rc; |
| } |
| period_us = led->mpp_cfg->pwm_cfg->pwm_period_us; |
| if (period_us > INT_MAX / NSEC_PER_USEC) { |
| duty_us = (period_us * led->cdev.brightness) / |
| LED_FULL; |
| rc = pwm_config_us( |
| led->mpp_cfg->pwm_cfg->pwm_dev, |
| duty_us, |
| period_us); |
| } else { |
| duty_ns = ((period_us * NSEC_PER_USEC) / |
| LED_FULL) * led->cdev.brightness; |
| rc = pwm_config( |
| led->mpp_cfg->pwm_cfg->pwm_dev, |
| duty_ns, |
| period_us * NSEC_PER_USEC); |
| } |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, "Failed to configure pwm for new values\n"); |
| goto err_mpp_reg_write; |
| } |
| } |
| |
| if (led->mpp_cfg->pwm_mode != MANUAL_MODE) { |
| pwm_enable(led->mpp_cfg->pwm_cfg->pwm_dev); |
| led->mpp_cfg->pwm_cfg->pwm_enabled = 1; |
| } else { |
| if (led->cdev.brightness < LED_MPP_CURRENT_MIN) |
| led->cdev.brightness = LED_MPP_CURRENT_MIN; |
| else { |
| /* |
| * PMIC supports LED intensity from 5mA - 40mA |
| * in steps of 5mA. Brightness is rounded to |
| * 5mA or nearest lower supported values |
| */ |
| led->cdev.brightness /= LED_MPP_CURRENT_MIN; |
| led->cdev.brightness *= LED_MPP_CURRENT_MIN; |
| } |
| |
| val = (led->cdev.brightness / LED_MPP_CURRENT_MIN) - 1; |
| |
| rc = qpnp_led_masked_write(led, |
| LED_MPP_SINK_CTRL(led->base), |
| LED_MPP_SINK_MASK, val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write sink control reg\n"); |
| goto err_mpp_reg_write; |
| } |
| } |
| |
| val = (led->mpp_cfg->source_sel & LED_MPP_SRC_MASK) | |
| (led->mpp_cfg->mode_ctrl & LED_MPP_MODE_CTRL_MASK); |
| |
| rc = qpnp_led_masked_write(led, |
| LED_MPP_MODE_CTRL(led->base), LED_MPP_MODE_MASK, |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led mode reg\n"); |
| goto err_mpp_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| LED_MPP_EN_CTRL(led->base), LED_MPP_EN_MASK, |
| LED_MPP_EN_ENABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Failed to write led enable reg\n"); |
| goto err_mpp_reg_write; |
| } |
| } else { |
| if (led->mpp_cfg->pwm_mode != MANUAL_MODE) { |
| led->mpp_cfg->pwm_cfg->mode = |
| led->mpp_cfg->pwm_cfg->default_mode; |
| led->mpp_cfg->pwm_mode = |
| led->mpp_cfg->pwm_cfg->default_mode; |
| pwm_disable(led->mpp_cfg->pwm_cfg->pwm_dev); |
| led->mpp_cfg->pwm_cfg->pwm_enabled = 0; |
| } |
| rc = qpnp_led_masked_write(led, |
| LED_MPP_MODE_CTRL(led->base), |
| LED_MPP_MODE_MASK, |
| LED_MPP_MODE_DISABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led mode reg\n"); |
| goto err_mpp_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| LED_MPP_EN_CTRL(led->base), |
| LED_MPP_EN_MASK, |
| LED_MPP_EN_DISABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| goto err_mpp_reg_write; |
| } |
| |
| if (led->mpp_cfg->mpp_reg && led->mpp_cfg->enable) { |
| rc = regulator_disable(led->mpp_cfg->mpp_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "MPP regulator disable failed(%d)\n", |
| rc); |
| return rc; |
| } |
| |
| rc = regulator_set_voltage(led->mpp_cfg->mpp_reg, |
| 0, led->mpp_cfg->max_uV); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "MPP regulator voltage set failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| led->mpp_cfg->enable = false; |
| } |
| |
| if (led->mpp_cfg->pwm_mode != MANUAL_MODE) |
| led->mpp_cfg->pwm_cfg->blinking = false; |
| qpnp_dump_regs(led, mpp_debug_regs, ARRAY_SIZE(mpp_debug_regs)); |
| |
| return 0; |
| |
| err_mpp_reg_write: |
| if (led->mpp_cfg->mpp_reg) |
| regulator_disable(led->mpp_cfg->mpp_reg); |
| err_reg_enable: |
| if (led->mpp_cfg->mpp_reg) |
| regulator_set_voltage(led->mpp_cfg->mpp_reg, 0, |
| led->mpp_cfg->max_uV); |
| led->mpp_cfg->enable = false; |
| |
| return rc; |
| } |
| |
| static int qpnp_gpio_set(struct qpnp_led_data *led) |
| { |
| int rc, val; |
| |
| if (led->cdev.brightness) { |
| val = (led->gpio_cfg->source_sel & LED_GPIO_SRC_MASK) | |
| (led->gpio_cfg->mode_ctrl & LED_GPIO_MODE_CTRL_MASK); |
| |
| rc = qpnp_led_masked_write(led, |
| LED_GPIO_MODE_CTRL(led->base), |
| LED_GPIO_MODE_MASK, |
| val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led mode reg\n"); |
| goto err_gpio_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| LED_GPIO_EN_CTRL(led->base), |
| LED_GPIO_EN_MASK, |
| LED_GPIO_EN_ENABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| goto err_gpio_reg_write; |
| } |
| |
| led->gpio_cfg->enable = true; |
| } else { |
| rc = qpnp_led_masked_write(led, |
| LED_GPIO_MODE_CTRL(led->base), |
| LED_GPIO_MODE_MASK, |
| LED_GPIO_MODE_DISABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led mode reg\n"); |
| goto err_gpio_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| LED_GPIO_EN_CTRL(led->base), |
| LED_GPIO_EN_MASK, |
| LED_GPIO_EN_DISABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| goto err_gpio_reg_write; |
| } |
| |
| led->gpio_cfg->enable = false; |
| } |
| |
| qpnp_dump_regs(led, gpio_debug_regs, ARRAY_SIZE(gpio_debug_regs)); |
| |
| return 0; |
| |
| err_gpio_reg_write: |
| led->gpio_cfg->enable = false; |
| |
| return rc; |
| } |
| |
| static int qpnp_flash_regulator_operate(struct qpnp_led_data *led, bool on) |
| { |
| int rc, i; |
| struct qpnp_led_data *led_array; |
| bool regulator_on = false; |
| |
| led_array = dev_get_drvdata(&led->pdev->dev); |
| if (!led_array) { |
| dev_err(&led->pdev->dev, "Unable to get LED array\n"); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < led->num_leds; i++) |
| regulator_on |= led_array[i].flash_cfg->flash_on; |
| |
| if (!on) |
| goto regulator_turn_off; |
| |
| if (!regulator_on && !led->flash_cfg->flash_on) { |
| for (i = 0; i < led->num_leds; i++) { |
| if (led_array[i].flash_cfg->flash_reg_get) { |
| if (led_array[i].flash_cfg->flash_wa_reg_get) { |
| rc = regulator_enable( |
| led_array[i].flash_cfg-> |
| flash_wa_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Flash wa regulator enable failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| rc = regulator_enable( |
| led_array[i].flash_cfg->flash_boost_reg); |
| if (rc) { |
| if (led_array[i].flash_cfg-> |
| flash_wa_reg_get) |
| /* |
| * Disable flash wa regulator |
| * when flash boost regulator |
| * enable fails |
| */ |
| regulator_disable( |
| led_array[i].flash_cfg-> |
| flash_wa_reg); |
| dev_err(&led->pdev->dev, "Flash boost regulator enable failed(%d)\n", |
| rc); |
| return rc; |
| } |
| led->flash_cfg->flash_on = true; |
| } |
| break; |
| } |
| } |
| |
| return 0; |
| |
| regulator_turn_off: |
| if (regulator_on && led->flash_cfg->flash_on) { |
| for (i = 0; i < led->num_leds; i++) { |
| if (led_array[i].flash_cfg->flash_reg_get) { |
| rc = qpnp_led_masked_write(led, |
| FLASH_ENABLE_CONTROL(led->base), |
| FLASH_ENABLE_MASK, |
| FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", |
| rc); |
| } |
| |
| rc = regulator_disable( |
| led_array[i].flash_cfg->flash_boost_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Flash boost regulator disable failed(%d)\n", |
| rc); |
| return rc; |
| } |
| if (led_array[i].flash_cfg->flash_wa_reg_get) { |
| rc = regulator_disable( |
| led_array[i].flash_cfg-> |
| flash_wa_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Flash_wa regulator disable failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| led->flash_cfg->flash_on = false; |
| } |
| break; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_torch_regulator_operate(struct qpnp_led_data *led, bool on) |
| { |
| int rc; |
| |
| if (!on) |
| goto regulator_turn_off; |
| |
| if (!led->flash_cfg->torch_on) { |
| rc = regulator_enable(led->flash_cfg->torch_boost_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Regulator enable failed(%d)\n", rc); |
| return rc; |
| } |
| led->flash_cfg->torch_on = true; |
| } |
| return 0; |
| |
| regulator_turn_off: |
| if (led->flash_cfg->torch_on) { |
| rc = qpnp_led_masked_write(led, FLASH_ENABLE_CONTROL(led->base), |
| FLASH_ENABLE_MODULE_MASK, FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", rc); |
| } |
| |
| rc = regulator_disable(led->flash_cfg->torch_boost_reg); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Regulator disable failed(%d)\n", rc); |
| return rc; |
| } |
| led->flash_cfg->torch_on = false; |
| } |
| return 0; |
| } |
| |
| static int qpnp_flash_set(struct qpnp_led_data *led) |
| { |
| int rc = 0, error; |
| int val = led->cdev.brightness; |
| |
| if (led->flash_cfg->torch_enable) |
| led->flash_cfg->current_prgm = |
| (val * TORCH_MAX_LEVEL / led->max_current); |
| else |
| led->flash_cfg->current_prgm = |
| (val * FLASH_MAX_LEVEL / led->max_current); |
| |
| /* Set led current */ |
| if (val > 0) { |
| if (led->flash_cfg->torch_enable) { |
| if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_DUAL) { |
| if (!led->flash_cfg->no_smbb_support) |
| rc = qpnp_torch_regulator_operate(led, |
| true); |
| else |
| rc = qpnp_flash_regulator_operate(led, |
| true); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Torch regulator operate failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } else if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_SINGLE) { |
| rc = qpnp_flash_regulator_operate(led, true); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Flash regulator operate failed(%d)\n", |
| rc); |
| goto error_flash_set; |
| } |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_MAX_CURR(led->base), |
| FLASH_CURRENT_MASK, |
| TORCH_MAX_LEVEL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Max current reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_TMR_CTRL(led->base), |
| FLASH_TMR_MASK, |
| FLASH_TMR_WATCHDOG); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Timer control reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| led->flash_cfg->current_addr, |
| FLASH_CURRENT_MASK, |
| led->flash_cfg->current_prgm); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Current reg write failed(%d)\n", rc); |
| goto error_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| led->flash_cfg->second_addr, |
| FLASH_CURRENT_MASK, |
| led->flash_cfg->current_prgm); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "2nd Current reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_WATCHDOG_TMR(led->base), |
| FLASH_WATCHDOG_MASK, |
| led->flash_cfg->duration); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Max current reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_ENABLE_CONTROL(led->base), |
| FLASH_ENABLE_MASK, |
| led->flash_cfg->enable_module); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| if (!led->flash_cfg->strobe_type) |
| led->flash_cfg->trigger_flash &= |
| ~FLASH_HW_SW_STROBE_SEL_MASK; |
| else |
| led->flash_cfg->trigger_flash |= |
| FLASH_HW_SW_STROBE_SEL_MASK; |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_STROBE_CTRL(led->base), |
| led->flash_cfg->trigger_flash, |
| led->flash_cfg->trigger_flash); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "LED %d strobe reg write failed(%d)\n", |
| led->id, rc); |
| goto error_reg_write; |
| } |
| } else { |
| rc = qpnp_flash_regulator_operate(led, true); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Flash regulator operate failed(%d)\n", |
| rc); |
| goto error_flash_set; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_TMR_CTRL(led->base), |
| FLASH_TMR_MASK, |
| FLASH_TMR_SAFETY); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Timer control reg write failed(%d)\n", |
| rc); |
| goto error_reg_write; |
| } |
| |
| /* Set flash safety timer */ |
| rc = qpnp_led_masked_write(led, |
| FLASH_SAFETY_TIMER(led->base), |
| FLASH_SAFETY_TIMER_MASK, |
| led->flash_cfg->duration); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Safety timer reg write failed(%d)\n", |
| rc); |
| goto error_flash_set; |
| } |
| |
| /* Set max current */ |
| rc = qpnp_led_masked_write(led, |
| FLASH_MAX_CURR(led->base), FLASH_CURRENT_MASK, |
| FLASH_MAX_LEVEL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Max current reg write failed(%d)\n", |
| rc); |
| goto error_flash_set; |
| } |
| |
| /* Set clamp current */ |
| rc = qpnp_led_masked_write(led, |
| FLASH_CLAMP_CURR(led->base), |
| FLASH_CURRENT_MASK, |
| led->flash_cfg->clamp_curr); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Clamp current reg write failed(%d)\n", |
| rc); |
| goto error_flash_set; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| led->flash_cfg->current_addr, |
| FLASH_CURRENT_MASK, |
| led->flash_cfg->current_prgm); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Current reg write failed(%d)\n", rc); |
| goto error_flash_set; |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_ENABLE_CONTROL(led->base), |
| led->flash_cfg->enable_module, |
| led->flash_cfg->enable_module); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", rc); |
| goto error_flash_set; |
| } |
| |
| /* |
| * Add 1ms delay for bharger enter stable state |
| */ |
| usleep_range(FLASH_RAMP_UP_DELAY_US, |
| FLASH_RAMP_UP_DELAY_US + 10); |
| |
| if (!led->flash_cfg->strobe_type) |
| led->flash_cfg->trigger_flash &= |
| ~FLASH_HW_SW_STROBE_SEL_MASK; |
| else |
| led->flash_cfg->trigger_flash |= |
| FLASH_HW_SW_STROBE_SEL_MASK; |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_STROBE_CTRL(led->base), |
| led->flash_cfg->trigger_flash, |
| led->flash_cfg->trigger_flash); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "LED %d strobe reg write failed(%d)\n", |
| led->id, rc); |
| goto error_flash_set; |
| } |
| } |
| } else { |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_STROBE_CTRL(led->base), |
| led->flash_cfg->trigger_flash, |
| FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "LED %d flash write failed(%d)\n", led->id, rc); |
| if (led->flash_cfg->torch_enable) |
| goto error_torch_set; |
| else |
| goto error_flash_set; |
| } |
| |
| if (led->flash_cfg->torch_enable) { |
| if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_DUAL) { |
| if (!led->flash_cfg->no_smbb_support) |
| rc = qpnp_torch_regulator_operate(led, |
| false); |
| else |
| rc = qpnp_flash_regulator_operate(led, |
| false); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Torch regulator operate failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } else if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_SINGLE) { |
| rc = qpnp_flash_regulator_operate(led, false); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Flash regulator operate failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| } else { |
| /* |
| * Disable module after ramp down complete for stable |
| * behavior |
| */ |
| usleep_range(FLASH_RAMP_UP_DELAY_US, |
| FLASH_RAMP_UP_DELAY_US + 10); |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_ENABLE_CONTROL(led->base), |
| led->flash_cfg->enable_module & |
| ~FLASH_ENABLE_MODULE_MASK, |
| FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", rc); |
| if (led->flash_cfg->torch_enable) |
| goto error_torch_set; |
| else |
| goto error_flash_set; |
| } |
| |
| rc = qpnp_flash_regulator_operate(led, false); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Flash regulator operate failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| } |
| |
| qpnp_dump_regs(led, flash_debug_regs, ARRAY_SIZE(flash_debug_regs)); |
| |
| return 0; |
| |
| error_reg_write: |
| if (led->flash_cfg->peripheral_subtype == FLASH_SUBTYPE_SINGLE) |
| goto error_flash_set; |
| |
| error_torch_set: |
| if (!led->flash_cfg->no_smbb_support) |
| error = qpnp_torch_regulator_operate(led, false); |
| else |
| error = qpnp_flash_regulator_operate(led, false); |
| if (error) { |
| dev_err(&led->pdev->dev, |
| "Torch regulator operate failed(%d)\n", rc); |
| return error; |
| } |
| return rc; |
| |
| error_flash_set: |
| error = qpnp_flash_regulator_operate(led, false); |
| if (error) { |
| dev_err(&led->pdev->dev, |
| "Flash regulator operate failed(%d)\n", rc); |
| return error; |
| } |
| return rc; |
| } |
| |
| static int qpnp_kpdbl_set(struct qpnp_led_data *led) |
| { |
| int rc; |
| int duty_us, duty_ns, period_us; |
| |
| if (led->cdev.brightness) { |
| if (!led->kpdbl_cfg->pwm_cfg->blinking) |
| led->kpdbl_cfg->pwm_cfg->mode = |
| led->kpdbl_cfg->pwm_cfg->default_mode; |
| |
| if (bitmap_empty(kpdbl_leds_in_use, NUM_KPDBL_LEDS)) { |
| rc = qpnp_led_masked_write(led, KPDBL_ENABLE(led->base), |
| KPDBL_MODULE_EN_MASK, KPDBL_MODULE_EN); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable reg write failed(%d)\n", rc); |
| return rc; |
| } |
| } |
| |
| /* On some platforms, GPLED1 channel should always be enabled |
| * for the other GPLEDs 2/3/4 to glow. Before enabling GPLED |
| * 2/3/4, first check if GPLED1 is already enabled. If GPLED1 |
| * channel is not enabled, then enable the GPLED1 channel but |
| * with a 0 brightness |
| */ |
| if (!led->kpdbl_cfg->always_on && |
| !test_bit(KPDBL_MASTER_BIT_INDEX, kpdbl_leds_in_use) && |
| kpdbl_master) { |
| rc = pwm_config_us(kpdbl_master, 0, |
| kpdbl_master_period_us); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm config failed\n"); |
| return rc; |
| } |
| |
| rc = pwm_enable(kpdbl_master); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm enable failed\n"); |
| return rc; |
| } |
| set_bit(KPDBL_MASTER_BIT_INDEX, |
| kpdbl_leds_in_use); |
| } |
| |
| if (led->kpdbl_cfg->pwm_cfg->mode == PWM_MODE) { |
| rc = pwm_change_mode(led->kpdbl_cfg->pwm_cfg->pwm_dev, |
| PM_PWM_MODE_PWM); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failed to set PWM mode, rc = %d\n", |
| rc); |
| return rc; |
| } |
| period_us = led->kpdbl_cfg->pwm_cfg->pwm_period_us; |
| if (period_us > INT_MAX / NSEC_PER_USEC) { |
| duty_us = (period_us * led->cdev.brightness) / |
| KPDBL_MAX_LEVEL; |
| rc = pwm_config_us( |
| led->kpdbl_cfg->pwm_cfg->pwm_dev, |
| duty_us, |
| period_us); |
| } else { |
| duty_ns = ((period_us * NSEC_PER_USEC) / |
| KPDBL_MAX_LEVEL) * led->cdev.brightness; |
| rc = pwm_config( |
| led->kpdbl_cfg->pwm_cfg->pwm_dev, |
| duty_ns, |
| period_us * NSEC_PER_USEC); |
| } |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm config failed\n"); |
| return rc; |
| } |
| } |
| |
| rc = pwm_enable(led->kpdbl_cfg->pwm_cfg->pwm_dev); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, "pwm enable failed\n"); |
| return rc; |
| } |
| led->kpdbl_cfg->pwm_cfg->pwm_enabled = 1; |
| set_bit(led->kpdbl_cfg->row_id, kpdbl_leds_in_use); |
| |
| /* is_kpdbl_master_turn_on will be set to true when GPLED1 |
| * channel is enabled and has a valid brightness value |
| */ |
| if (led->kpdbl_cfg->always_on) |
| is_kpdbl_master_turn_on = true; |
| |
| } else { |
| led->kpdbl_cfg->pwm_cfg->mode = |
| led->kpdbl_cfg->pwm_cfg->default_mode; |
| |
| /* Before disabling GPLED1, check if any other GPLED 2/3/4 is |
| * on. If any of the other GPLED 2/3/4 is on, then have the |
| * GPLED1 channel enabled with 0 brightness. |
| */ |
| if (led->kpdbl_cfg->always_on) { |
| if (bitmap_weight(kpdbl_leds_in_use, |
| NUM_KPDBL_LEDS) > 1) { |
| rc = pwm_config_us( |
| led->kpdbl_cfg->pwm_cfg->pwm_dev, 0, |
| led->kpdbl_cfg->pwm_cfg->pwm_period_us); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm config failed\n"); |
| return rc; |
| } |
| |
| rc = pwm_enable(led->kpdbl_cfg->pwm_cfg-> |
| pwm_dev); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm enable failed\n"); |
| return rc; |
| } |
| led->kpdbl_cfg->pwm_cfg->pwm_enabled = 1; |
| } else { |
| if (kpdbl_master) { |
| pwm_disable(kpdbl_master); |
| clear_bit(KPDBL_MASTER_BIT_INDEX, |
| kpdbl_leds_in_use); |
| rc = qpnp_led_masked_write( |
| led, KPDBL_ENABLE(led->base), |
| KPDBL_MODULE_EN_MASK, |
| KPDBL_MODULE_DIS); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Failed to write led enable reg\n"); |
| return rc; |
| } |
| } |
| } |
| is_kpdbl_master_turn_on = false; |
| } else { |
| pwm_disable(led->kpdbl_cfg->pwm_cfg->pwm_dev); |
| led->kpdbl_cfg->pwm_cfg->pwm_enabled = 0; |
| clear_bit(led->kpdbl_cfg->row_id, kpdbl_leds_in_use); |
| if (bitmap_weight(kpdbl_leds_in_use, |
| NUM_KPDBL_LEDS) == 1 && kpdbl_master && |
| !is_kpdbl_master_turn_on) { |
| pwm_disable(kpdbl_master); |
| clear_bit(KPDBL_MASTER_BIT_INDEX, |
| kpdbl_leds_in_use); |
| rc = qpnp_led_masked_write( |
| led, KPDBL_ENABLE(led->base), |
| KPDBL_MODULE_EN_MASK, KPDBL_MODULE_DIS); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| return rc; |
| } |
| is_kpdbl_master_turn_on = false; |
| } |
| } |
| } |
| |
| led->kpdbl_cfg->pwm_cfg->blinking = false; |
| |
| qpnp_dump_regs(led, kpdbl_debug_regs, ARRAY_SIZE(kpdbl_debug_regs)); |
| |
| return 0; |
| } |
| |
| static int qpnp_rgb_set(struct qpnp_led_data *led) |
| { |
| int rc; |
| int duty_us, duty_ns, period_us; |
| |
| if (led->cdev.brightness) { |
| if (!led->rgb_cfg->pwm_cfg->blinking) |
| led->rgb_cfg->pwm_cfg->mode = |
| led->rgb_cfg->pwm_cfg->default_mode; |
| if (led->rgb_cfg->pwm_cfg->mode == PWM_MODE) { |
| rc = pwm_change_mode(led->rgb_cfg->pwm_cfg->pwm_dev, |
| PM_PWM_MODE_PWM); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failed to set PWM mode, rc = %d\n", |
| rc); |
| return rc; |
| } |
| } |
| period_us = led->rgb_cfg->pwm_cfg->pwm_period_us; |
| if (period_us > INT_MAX / NSEC_PER_USEC) { |
| duty_us = (period_us * led->cdev.brightness) / |
| LED_FULL; |
| rc = pwm_config_us( |
| led->rgb_cfg->pwm_cfg->pwm_dev, |
| duty_us, |
| period_us); |
| } else { |
| duty_ns = ((period_us * NSEC_PER_USEC) / |
| LED_FULL) * led->cdev.brightness; |
| rc = pwm_config( |
| led->rgb_cfg->pwm_cfg->pwm_dev, |
| duty_ns, |
| period_us * NSEC_PER_USEC); |
| } |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "pwm config failed\n"); |
| return rc; |
| } |
| rc = qpnp_led_masked_write(led, |
| RGB_LED_EN_CTL(led->base), |
| led->rgb_cfg->enable, led->rgb_cfg->enable); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| return rc; |
| } |
| if (!led->rgb_cfg->pwm_cfg->pwm_enabled) { |
| pwm_enable(led->rgb_cfg->pwm_cfg->pwm_dev); |
| led->rgb_cfg->pwm_cfg->pwm_enabled = 1; |
| } |
| } else { |
| led->rgb_cfg->pwm_cfg->mode = |
| led->rgb_cfg->pwm_cfg->default_mode; |
| if (led->rgb_cfg->pwm_cfg->pwm_enabled) { |
| pwm_disable(led->rgb_cfg->pwm_cfg->pwm_dev); |
| led->rgb_cfg->pwm_cfg->pwm_enabled = 0; |
| } |
| rc = qpnp_led_masked_write(led, |
| RGB_LED_EN_CTL(led->base), |
| led->rgb_cfg->enable, RGB_LED_DISABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led enable reg\n"); |
| return rc; |
| } |
| } |
| |
| led->rgb_cfg->pwm_cfg->blinking = false; |
| qpnp_dump_regs(led, rgb_pwm_debug_regs, ARRAY_SIZE(rgb_pwm_debug_regs)); |
| |
| return 0; |
| } |
| |
| static void qpnp_led_set(struct led_classdev *led_cdev, |
| enum led_brightness value) |
| { |
| struct qpnp_led_data *led; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| if (value < LED_OFF) { |
| dev_err(&led->pdev->dev, "Invalid brightness value\n"); |
| return; |
| } |
| |
| if (value > led->cdev.max_brightness) |
| value = led->cdev.max_brightness; |
| |
| led->cdev.brightness = value; |
| if (led->in_order_command_processing) |
| queue_work(led->workqueue, &led->work); |
| else |
| schedule_work(&led->work); |
| } |
| |
| static void __qpnp_led_work(struct qpnp_led_data *led, |
| enum led_brightness value) |
| { |
| int rc; |
| |
| if (led->id == QPNP_ID_FLASH1_LED0 || led->id == QPNP_ID_FLASH1_LED1) |
| mutex_lock(&flash_lock); |
| else |
| mutex_lock(&led->lock); |
| |
| switch (led->id) { |
| case QPNP_ID_WLED: |
| rc = qpnp_wled_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "WLED set brightness failed (%d)\n", rc); |
| break; |
| case QPNP_ID_FLASH1_LED0: |
| case QPNP_ID_FLASH1_LED1: |
| rc = qpnp_flash_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "FLASH set brightness failed (%d)\n", rc); |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| rc = qpnp_rgb_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "RGB set brightness failed (%d)\n", rc); |
| break; |
| case QPNP_ID_LED_MPP: |
| rc = qpnp_mpp_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "MPP set brightness failed (%d)\n", rc); |
| break; |
| case QPNP_ID_LED_GPIO: |
| rc = qpnp_gpio_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "GPIO set brightness failed (%d)\n", |
| rc); |
| break; |
| case QPNP_ID_KPDBL: |
| rc = qpnp_kpdbl_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "KPDBL set brightness failed (%d)\n", rc); |
| break; |
| default: |
| dev_err(&led->pdev->dev, "Invalid LED(%d)\n", led->id); |
| break; |
| } |
| if (led->id == QPNP_ID_FLASH1_LED0 || led->id == QPNP_ID_FLASH1_LED1) |
| mutex_unlock(&flash_lock); |
| else |
| mutex_unlock(&led->lock); |
| |
| } |
| |
| static void qpnp_led_work(struct work_struct *work) |
| { |
| struct qpnp_led_data *led = container_of(work, |
| struct qpnp_led_data, work); |
| |
| __qpnp_led_work(led, led->cdev.brightness); |
| } |
| |
| static int qpnp_led_set_max_brightness(struct qpnp_led_data *led) |
| { |
| switch (led->id) { |
| case QPNP_ID_WLED: |
| led->cdev.max_brightness = WLED_MAX_LEVEL; |
| break; |
| case QPNP_ID_FLASH1_LED0: |
| case QPNP_ID_FLASH1_LED1: |
| led->cdev.max_brightness = led->max_current; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| led->cdev.max_brightness = RGB_MAX_LEVEL; |
| break; |
| case QPNP_ID_LED_MPP: |
| if (led->mpp_cfg->pwm_mode == MANUAL_MODE) |
| led->cdev.max_brightness = led->max_current; |
| else |
| led->cdev.max_brightness = MPP_MAX_LEVEL; |
| break; |
| case QPNP_ID_LED_GPIO: |
| led->cdev.max_brightness = led->max_current; |
| break; |
| case QPNP_ID_KPDBL: |
| led->cdev.max_brightness = KPDBL_MAX_LEVEL; |
| break; |
| default: |
| dev_err(&led->pdev->dev, "Invalid LED(%d)\n", led->id); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static enum led_brightness qpnp_led_get(struct led_classdev *led_cdev) |
| { |
| struct qpnp_led_data *led; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| return led->cdev.brightness; |
| } |
| |
| static void qpnp_led_turn_off_delayed(struct work_struct *work) |
| { |
| struct delayed_work *dwork = to_delayed_work(work); |
| struct qpnp_led_data *led |
| = container_of(dwork, struct qpnp_led_data, dwork); |
| |
| led->cdev.brightness = LED_OFF; |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| } |
| |
| static void qpnp_led_turn_off(struct qpnp_led_data *led) |
| { |
| INIT_DELAYED_WORK(&led->dwork, qpnp_led_turn_off_delayed); |
| schedule_delayed_work(&led->dwork, |
| msecs_to_jiffies(led->turn_off_delay_ms)); |
| } |
| |
| static int qpnp_wled_init(struct qpnp_led_data *led) |
| { |
| int rc, i; |
| u8 num_wled_strings, val = 0; |
| |
| num_wled_strings = led->wled_cfg->num_strings; |
| |
| /* verify ranges */ |
| if (led->wled_cfg->ovp_val > WLED_OVP_27V) { |
| dev_err(&led->pdev->dev, "Invalid ovp value\n"); |
| return -EINVAL; |
| } |
| |
| if (led->wled_cfg->boost_curr_lim > WLED_CURR_LIMIT_1680mA) { |
| dev_err(&led->pdev->dev, "Invalid boost current limit\n"); |
| return -EINVAL; |
| } |
| |
| if (led->wled_cfg->cp_select > WLED_CP_SELECT_MAX) { |
| dev_err(&led->pdev->dev, "Invalid pole capacitance\n"); |
| return -EINVAL; |
| } |
| |
| if (led->max_current > WLED_MAX_CURR) { |
| dev_err(&led->pdev->dev, "Invalid max current\n"); |
| return -EINVAL; |
| } |
| |
| if ((led->wled_cfg->ctrl_delay_us % WLED_CTL_DLY_STEP) || |
| (led->wled_cfg->ctrl_delay_us > WLED_CTL_DLY_MAX)) { |
| dev_err(&led->pdev->dev, "Invalid control delay\n"); |
| return -EINVAL; |
| } |
| |
| /* program over voltage protection threshold */ |
| rc = qpnp_led_masked_write(led, WLED_OVP_CFG_REG(led->base), |
| WLED_OVP_VAL_MASK, |
| (led->wled_cfg->ovp_val << WLED_OVP_VAL_BIT_SHFT)); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED OVP reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* program current boost limit */ |
| rc = qpnp_led_masked_write(led, WLED_BOOST_LIMIT_REG(led->base), |
| WLED_BOOST_LIMIT_MASK, led->wled_cfg->boost_curr_lim); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED boost limit reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* program output feedback */ |
| rc = qpnp_led_masked_write(led, WLED_FDBCK_CTRL_REG(led->base), |
| WLED_OP_FDBCK_MASK, |
| (led->wled_cfg->op_fdbck << WLED_OP_FDBCK_BIT_SHFT)); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED fdbck ctrl reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* program switch frequency */ |
| rc = qpnp_led_masked_write(led, |
| WLED_SWITCHING_FREQ_REG(led->base), |
| WLED_SWITCH_FREQ_MASK, led->wled_cfg->switch_freq); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED switch freq reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* program current sink */ |
| if (led->wled_cfg->cs_out_en) { |
| for (i = 0; i < led->wled_cfg->num_strings; i++) |
| val |= 1 << i; |
| rc = qpnp_led_masked_write(led, WLED_CURR_SINK_REG(led->base), |
| WLED_CURR_SINK_MASK, (val << WLED_CURR_SINK_SHFT)); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED curr sink reg write failed(%d)\n", rc); |
| return rc; |
| } |
| } |
| |
| /* program high pole capacitance */ |
| rc = qpnp_led_masked_write(led, WLED_HIGH_POLE_CAP_REG(led->base), |
| WLED_CP_SELECT_MASK, led->wled_cfg->cp_select); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED pole cap reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* program modulator, current mod src and cabc */ |
| for (i = 0; i < num_wled_strings; i++) { |
| rc = qpnp_led_masked_write(led, WLED_MOD_EN_REG(led->base, i), |
| WLED_NO_MASK, WLED_EN_MASK); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED mod enable reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| if (led->wled_cfg->dig_mod_gen_en) { |
| rc = qpnp_led_masked_write(led, |
| WLED_MOD_SRC_SEL_REG(led->base, i), |
| WLED_NO_MASK, WLED_USE_EXT_GEN_MOD_SRC); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED dig mod en reg write failed(%d)\n", rc); |
| } |
| } |
| |
| rc = qpnp_led_masked_write(led, |
| WLED_FULL_SCALE_REG(led->base, i), WLED_MAX_CURR_MASK, |
| (u8)led->max_current); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED max current reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| } |
| |
| /* Reset WLED enable register */ |
| rc = qpnp_led_masked_write(led, WLED_MOD_CTRL_REG(led->base), |
| WLED_8_BIT_MASK, WLED_BOOST_OFF); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "WLED write ctrl reg failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* dump wled registers */ |
| qpnp_dump_regs(led, wled_debug_regs, ARRAY_SIZE(wled_debug_regs)); |
| |
| return 0; |
| } |
| |
| static ssize_t led_mode_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| unsigned long state; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret = -EINVAL; |
| |
| ret = kstrtoul(buf, 10, &state); |
| if (ret) |
| return ret; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| /* '1' to enable torch mode; '0' to switch to flash mode */ |
| if (state == 1) |
| led->flash_cfg->torch_enable = true; |
| else |
| led->flash_cfg->torch_enable = false; |
| |
| return count; |
| } |
| |
| static ssize_t led_strobe_type_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| unsigned long state; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret = -EINVAL; |
| |
| ret = kstrtoul(buf, 10, &state); |
| if (ret) |
| return ret; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| /* '0' for sw strobe; '1' for hw strobe */ |
| if (state == 1) |
| led->flash_cfg->strobe_type = 1; |
| else |
| led->flash_cfg->strobe_type = 0; |
| |
| return count; |
| } |
| |
| static int qpnp_pwm_init(struct pwm_config_data *pwm_cfg, |
| struct platform_device *pdev, |
| const char *name) |
| { |
| int rc, start_idx, idx_len, lut_max_size; |
| |
| if (pwm_cfg->pwm_dev) { |
| if (pwm_cfg->mode == LPG_MODE) { |
| start_idx = |
| pwm_cfg->duty_cycles->start_idx; |
| idx_len = |
| pwm_cfg->duty_cycles->num_duty_pcts; |
| |
| if (strnstr(name, "kpdbl", sizeof("kpdbl"))) |
| lut_max_size = PWM_GPLED_LUT_MAX_SIZE; |
| else |
| lut_max_size = PWM_LUT_MAX_SIZE; |
| |
| if (idx_len >= lut_max_size && start_idx) { |
| dev_err(&pdev->dev, |
| "Wrong LUT size or index\n"); |
| return -EINVAL; |
| } |
| |
| if ((start_idx + idx_len) > lut_max_size) { |
| dev_err(&pdev->dev, "Exceed LUT limit\n"); |
| return -EINVAL; |
| } |
| rc = pwm_lut_config(pwm_cfg->pwm_dev, |
| pwm_cfg->pwm_period_us, |
| pwm_cfg->duty_cycles->duty_pcts, |
| pwm_cfg->lut_params); |
| if (rc < 0) { |
| dev_err(&pdev->dev, "Failed to configure pwm LUT\n"); |
| return rc; |
| } |
| rc = pwm_change_mode(pwm_cfg->pwm_dev, PM_PWM_MODE_LPG); |
| if (rc < 0) { |
| dev_err(&pdev->dev, "Failed to set LPG mode\n"); |
| return rc; |
| } |
| } |
| } else { |
| dev_err(&pdev->dev, "Invalid PWM device\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static ssize_t pwm_us_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 pwm_us; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_pwm_us; |
| struct pwm_config_data *pwm_cfg; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| ret = kstrtou32(buf, 10, &pwm_us); |
| if (ret) |
| return ret; |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, "Invalid LED id type for pwm_us\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_pwm_us = pwm_cfg->pwm_period_us; |
| |
| pwm_cfg->pwm_period_us = pwm_us; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->pwm_period_us = previous_pwm_us; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new pwm_us value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t pause_lo_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 pause_lo; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_pause_lo; |
| struct pwm_config_data *pwm_cfg; |
| |
| ret = kstrtou32(buf, 10, &pause_lo); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for pause lo\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_pause_lo = pwm_cfg->lut_params.lut_pause_lo; |
| |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| pwm_cfg->lut_params.lut_pause_lo = pause_lo; |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->lut_params.lut_pause_lo = previous_pause_lo; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new pause lo value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t pause_hi_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 pause_hi; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_pause_hi; |
| struct pwm_config_data *pwm_cfg; |
| |
| ret = kstrtou32(buf, 10, &pause_hi); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for pause hi\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_pause_hi = pwm_cfg->lut_params.lut_pause_hi; |
| |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| pwm_cfg->lut_params.lut_pause_hi = pause_hi; |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->lut_params.lut_pause_hi = previous_pause_hi; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new pause hi value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t start_idx_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 start_idx; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_start_idx; |
| struct pwm_config_data *pwm_cfg; |
| |
| ret = kstrtou32(buf, 10, &start_idx); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for start idx\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_start_idx = pwm_cfg->duty_cycles->start_idx; |
| pwm_cfg->duty_cycles->start_idx = start_idx; |
| pwm_cfg->lut_params.start_idx = pwm_cfg->duty_cycles->start_idx; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->duty_cycles->start_idx = previous_start_idx; |
| pwm_cfg->lut_params.start_idx = pwm_cfg->duty_cycles->start_idx; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new start idx value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t ramp_step_ms_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 ramp_step_ms; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_ramp_step_ms; |
| struct pwm_config_data *pwm_cfg; |
| |
| ret = kstrtou32(buf, 10, &ramp_step_ms); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for ramp step\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_ramp_step_ms = pwm_cfg->lut_params.ramp_step_ms; |
| |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| pwm_cfg->lut_params.ramp_step_ms = ramp_step_ms; |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->lut_params.ramp_step_ms = previous_ramp_step_ms; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new ramp step value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t lut_flags_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| u32 lut_flags; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret; |
| u32 previous_lut_flags; |
| struct pwm_config_data *pwm_cfg; |
| |
| ret = kstrtou32(buf, 10, &lut_flags); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for lut flags\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| previous_lut_flags = pwm_cfg->lut_params.flags; |
| |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| pwm_cfg->lut_params.flags = lut_flags; |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) { |
| pwm_cfg->lut_params.flags = previous_lut_flags; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new lut flags value\n"); |
| return ret; |
| } |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| } |
| |
| static ssize_t duty_pcts_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| int num_duty_pcts = 0; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| char *buffer; |
| ssize_t ret; |
| int i = 0; |
| int max_duty_pcts; |
| struct pwm_config_data *pwm_cfg; |
| u32 previous_num_duty_pcts; |
| int value; |
| int *previous_duty_pcts; |
| |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| pwm_cfg = led->mpp_cfg->pwm_cfg; |
| max_duty_pcts = PWM_LUT_MAX_SIZE; |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| pwm_cfg = led->rgb_cfg->pwm_cfg; |
| max_duty_pcts = PWM_LUT_MAX_SIZE; |
| break; |
| case QPNP_ID_KPDBL: |
| pwm_cfg = led->kpdbl_cfg->pwm_cfg; |
| max_duty_pcts = PWM_GPLED_LUT_MAX_SIZE; |
| break; |
| default: |
| dev_err(&led->pdev->dev, |
| "Invalid LED id type for duty pcts\n"); |
| return -EINVAL; |
| } |
| |
| if (pwm_cfg->mode == LPG_MODE) |
| pwm_cfg->blinking = true; |
| |
| buffer = (char *)buf; |
| |
| for (i = 0; i < max_duty_pcts; i++) { |
| if (buffer == NULL) |
| break; |
| ret = sscanf((const char *)buffer, "%u,%s", &value, buffer); |
| pwm_cfg->old_duty_pcts[i] = value; |
| num_duty_pcts++; |
| if (ret <= 1) |
| break; |
| } |
| |
| if (num_duty_pcts >= max_duty_pcts) { |
| dev_err(&led->pdev->dev, |
| "Number of duty pcts given exceeds max (%d)\n", |
| max_duty_pcts); |
| return -EINVAL; |
| } |
| |
| previous_num_duty_pcts = pwm_cfg->duty_cycles->num_duty_pcts; |
| previous_duty_pcts = pwm_cfg->duty_cycles->duty_pcts; |
| |
| pwm_cfg->duty_cycles->num_duty_pcts = num_duty_pcts; |
| pwm_cfg->duty_cycles->duty_pcts = pwm_cfg->old_duty_pcts; |
| pwm_cfg->old_duty_pcts = previous_duty_pcts; |
| pwm_cfg->lut_params.idx_len = pwm_cfg->duty_cycles->num_duty_pcts; |
| |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| |
| ret = qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (ret) |
| goto restore; |
| |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return count; |
| |
| restore: |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm with new duty pcts value\n"); |
| pwm_cfg->duty_cycles->num_duty_pcts = previous_num_duty_pcts; |
| pwm_cfg->old_duty_pcts = pwm_cfg->duty_cycles->duty_pcts; |
| pwm_cfg->duty_cycles->duty_pcts = previous_duty_pcts; |
| pwm_cfg->lut_params.idx_len = pwm_cfg->duty_cycles->num_duty_pcts; |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| qpnp_led_set(&led->cdev, led->cdev.brightness); |
| return ret; |
| } |
| |
| static void led_blink(struct qpnp_led_data *led, |
| struct pwm_config_data *pwm_cfg) |
| { |
| int rc; |
| |
| flush_work(&led->work); |
| mutex_lock(&led->lock); |
| if (pwm_cfg->use_blink) { |
| if (led->cdev.brightness) { |
| pwm_cfg->blinking = true; |
| if (led->id == QPNP_ID_LED_MPP) |
| led->mpp_cfg->pwm_mode = LPG_MODE; |
| else if (led->id == QPNP_ID_KPDBL) |
| led->kpdbl_cfg->pwm_mode = LPG_MODE; |
| pwm_cfg->mode = LPG_MODE; |
| } else { |
| pwm_cfg->blinking = false; |
| pwm_cfg->mode = pwm_cfg->default_mode; |
| if (led->id == QPNP_ID_LED_MPP) |
| led->mpp_cfg->pwm_mode = pwm_cfg->default_mode; |
| else if (led->id == QPNP_ID_KPDBL) |
| led->kpdbl_cfg->pwm_mode = |
| pwm_cfg->default_mode; |
| } |
| if (pwm_cfg->pwm_enabled) { |
| pwm_disable(pwm_cfg->pwm_dev); |
| pwm_cfg->pwm_enabled = 0; |
| } |
| qpnp_pwm_init(pwm_cfg, led->pdev, led->cdev.name); |
| if (led->id == QPNP_ID_RGB_RED || led->id == QPNP_ID_RGB_GREEN |
| || led->id == QPNP_ID_RGB_BLUE) { |
| rc = qpnp_rgb_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "RGB set brightness failed (%d)\n", rc); |
| } else if (led->id == QPNP_ID_LED_MPP) { |
| rc = qpnp_mpp_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "MPP set brightness failed (%d)\n", rc); |
| } else if (led->id == QPNP_ID_KPDBL) { |
| rc = qpnp_kpdbl_set(led); |
| if (rc < 0) |
| dev_err(&led->pdev->dev, |
| "KPDBL set brightness failed (%d)\n", rc); |
| } |
| } |
| mutex_unlock(&led->lock); |
| } |
| |
| static ssize_t blink_store(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct qpnp_led_data *led; |
| unsigned long blinking; |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| ssize_t ret = -EINVAL; |
| |
| ret = kstrtoul(buf, 10, &blinking); |
| if (ret) |
| return ret; |
| led = container_of(led_cdev, struct qpnp_led_data, cdev); |
| led->cdev.brightness = blinking ? led->cdev.max_brightness : 0; |
| |
| switch (led->id) { |
| case QPNP_ID_LED_MPP: |
| led_blink(led, led->mpp_cfg->pwm_cfg); |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| led_blink(led, led->rgb_cfg->pwm_cfg); |
| break; |
| case QPNP_ID_KPDBL: |
| led_blink(led, led->kpdbl_cfg->pwm_cfg); |
| break; |
| default: |
| dev_err(&led->pdev->dev, "Invalid LED id type for blink\n"); |
| return -EINVAL; |
| } |
| return count; |
| } |
| |
| static DEVICE_ATTR(led_mode, 0664, NULL, led_mode_store); |
| static DEVICE_ATTR(strobe, 0664, NULL, led_strobe_type_store); |
| static DEVICE_ATTR(pwm_us, 0664, NULL, pwm_us_store); |
| static DEVICE_ATTR(pause_lo, 0664, NULL, pause_lo_store); |
| static DEVICE_ATTR(pause_hi, 0664, NULL, pause_hi_store); |
| static DEVICE_ATTR(start_idx, 0664, NULL, start_idx_store); |
| static DEVICE_ATTR(ramp_step_ms, 0664, NULL, ramp_step_ms_store); |
| static DEVICE_ATTR(lut_flags, 0664, NULL, lut_flags_store); |
| static DEVICE_ATTR(duty_pcts, 0664, NULL, duty_pcts_store); |
| static DEVICE_ATTR(blink, 0664, NULL, blink_store); |
| |
| static struct attribute *led_attrs[] = { |
| &dev_attr_led_mode.attr, |
| &dev_attr_strobe.attr, |
| NULL |
| }; |
| |
| static const struct attribute_group led_attr_group = { |
| .attrs = led_attrs, |
| }; |
| |
| static struct attribute *pwm_attrs[] = { |
| &dev_attr_pwm_us.attr, |
| NULL |
| }; |
| |
| static struct attribute *lpg_attrs[] = { |
| &dev_attr_pause_lo.attr, |
| &dev_attr_pause_hi.attr, |
| &dev_attr_start_idx.attr, |
| &dev_attr_ramp_step_ms.attr, |
| &dev_attr_lut_flags.attr, |
| &dev_attr_duty_pcts.attr, |
| NULL |
| }; |
| |
| static struct attribute *blink_attrs[] = { |
| &dev_attr_blink.attr, |
| NULL |
| }; |
| |
| static const struct attribute_group pwm_attr_group = { |
| .attrs = pwm_attrs, |
| }; |
| |
| static const struct attribute_group lpg_attr_group = { |
| .attrs = lpg_attrs, |
| }; |
| |
| static const struct attribute_group blink_attr_group = { |
| .attrs = blink_attrs, |
| }; |
| |
| static int qpnp_flash_init(struct qpnp_led_data *led) |
| { |
| int rc; |
| |
| led->flash_cfg->flash_on = false; |
| |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_STROBE_CTRL(led->base), |
| FLASH_STROBE_MASK, FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "LED %d flash write failed(%d)\n", led->id, rc); |
| return rc; |
| } |
| |
| /* Disable flash LED module */ |
| rc = qpnp_led_masked_write(led, FLASH_ENABLE_CONTROL(led->base), |
| FLASH_ENABLE_MASK, FLASH_DISABLE_ALL); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Enable reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| if (led->flash_cfg->torch_enable) |
| return 0; |
| |
| /* Set headroom */ |
| rc = qpnp_led_masked_write(led, FLASH_HEADROOM(led->base), |
| FLASH_HEADROOM_MASK, led->flash_cfg->headroom); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Headroom reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* Set startup delay */ |
| rc = qpnp_led_masked_write(led, |
| FLASH_STARTUP_DELAY(led->base), FLASH_STARTUP_DLY_MASK, |
| led->flash_cfg->startup_dly); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Startup delay reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* Set timer control - safety or watchdog */ |
| if (led->flash_cfg->safety_timer) { |
| rc = qpnp_led_masked_write(led, |
| FLASH_LED_TMR_CTRL(led->base), |
| FLASH_TMR_MASK, FLASH_TMR_SAFETY); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "LED timer ctrl reg write failed(%d)\n", |
| rc); |
| return rc; |
| } |
| } |
| |
| /* Set Vreg force */ |
| if (led->flash_cfg->vreg_ok) |
| rc = qpnp_led_masked_write(led, FLASH_VREG_OK_FORCE(led->base), |
| FLASH_VREG_MASK, FLASH_SW_VREG_OK); |
| else |
| rc = qpnp_led_masked_write(led, FLASH_VREG_OK_FORCE(led->base), |
| FLASH_VREG_MASK, FLASH_HW_VREG_OK); |
| |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Vreg OK reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* Set self fault check */ |
| rc = qpnp_led_masked_write(led, FLASH_FAULT_DETECT(led->base), |
| FLASH_FAULT_DETECT_MASK, FLASH_SELFCHECK_ENABLE); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Fault detect reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* Set mask enable */ |
| rc = qpnp_led_masked_write(led, FLASH_MASK_ENABLE(led->base), |
| FLASH_MASK_REG_MASK, FLASH_MASK_1); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Mask enable reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| /* Set current ramp */ |
| rc = qpnp_led_masked_write(led, FLASH_CURRENT_RAMP(led->base), |
| FLASH_CURRENT_RAMP_MASK, FLASH_RAMP_STEP_27US); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Current ramp reg write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| led->flash_cfg->strobe_type = 0; |
| |
| /* dump flash registers */ |
| qpnp_dump_regs(led, flash_debug_regs, ARRAY_SIZE(flash_debug_regs)); |
| |
| return 0; |
| } |
| |
| static int qpnp_kpdbl_init(struct qpnp_led_data *led) |
| { |
| int rc; |
| uint val; |
| |
| /* select row source - vbst or vph */ |
| rc = regmap_read(led->regmap, KPDBL_ROW_SRC_SEL(led->base), &val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read from addr=%x, rc(%d)\n", |
| KPDBL_ROW_SRC_SEL(led->base), rc); |
| return rc; |
| } |
| |
| if (led->kpdbl_cfg->row_src_vbst) |
| val |= 1 << led->kpdbl_cfg->row_id; |
| else |
| val &= ~(1 << led->kpdbl_cfg->row_id); |
| |
| rc = regmap_write(led->regmap, KPDBL_ROW_SRC_SEL(led->base), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read from addr=%x, rc(%d)\n", |
| KPDBL_ROW_SRC_SEL(led->base), rc); |
| return rc; |
| } |
| |
| /* row source enable */ |
| rc = regmap_read(led->regmap, KPDBL_ROW_SRC(led->base), &val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read from addr=%x, rc(%d)\n", |
| KPDBL_ROW_SRC(led->base), rc); |
| return rc; |
| } |
| |
| if (led->kpdbl_cfg->row_src_en) |
| val |= KPDBL_ROW_SCAN_EN_MASK | (1 << led->kpdbl_cfg->row_id); |
| else |
| val &= ~(1 << led->kpdbl_cfg->row_id); |
| |
| rc = regmap_write(led->regmap, KPDBL_ROW_SRC(led->base), val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to write to addr=%x, rc(%d)\n", |
| KPDBL_ROW_SRC(led->base), rc); |
| return rc; |
| } |
| |
| /* enable module */ |
| rc = qpnp_led_masked_write(led, KPDBL_ENABLE(led->base), |
| KPDBL_MODULE_EN_MASK, KPDBL_MODULE_EN); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Enable module write failed(%d)\n", rc); |
| return rc; |
| } |
| |
| rc = qpnp_pwm_init(led->kpdbl_cfg->pwm_cfg, led->pdev, |
| led->cdev.name); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Failed to initialize pwm\n"); |
| return rc; |
| } |
| |
| if (led->kpdbl_cfg->always_on) { |
| kpdbl_master = led->kpdbl_cfg->pwm_cfg->pwm_dev; |
| kpdbl_master_period_us = led->kpdbl_cfg->pwm_cfg->pwm_period_us; |
| } |
| |
| /* dump kpdbl registers */ |
| qpnp_dump_regs(led, kpdbl_debug_regs, ARRAY_SIZE(kpdbl_debug_regs)); |
| |
| return 0; |
| } |
| |
| static int qpnp_rgb_init(struct qpnp_led_data *led) |
| { |
| int rc; |
| |
| rc = qpnp_led_masked_write(led, RGB_LED_SRC_SEL(led->base), |
| RGB_LED_SRC_MASK, RGB_LED_SOURCE_VPH_PWR); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led source select register\n"); |
| return rc; |
| } |
| |
| rc = qpnp_pwm_init(led->rgb_cfg->pwm_cfg, led->pdev, led->cdev.name); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Failed to initialize pwm\n"); |
| return rc; |
| } |
| /* Initialize led for use in auto trickle charging mode */ |
| rc = qpnp_led_masked_write(led, RGB_LED_ATC_CTL(led->base), |
| led->rgb_cfg->enable, led->rgb_cfg->enable); |
| |
| return 0; |
| } |
| |
| static int qpnp_mpp_init(struct qpnp_led_data *led) |
| { |
| int rc; |
| u8 val; |
| |
| |
| if (led->max_current < LED_MPP_CURRENT_MIN || |
| led->max_current > LED_MPP_CURRENT_MAX) { |
| dev_err(&led->pdev->dev, |
| "max current for mpp is not valid\n"); |
| return -EINVAL; |
| } |
| |
| val = (led->mpp_cfg->current_setting / LED_MPP_CURRENT_PER_SETTING) - 1; |
| |
| if (val < 0) |
| val = 0; |
| |
| rc = qpnp_led_masked_write(led, LED_MPP_VIN_CTRL(led->base), |
| LED_MPP_VIN_MASK, led->mpp_cfg->vin_ctrl); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led vin control reg\n"); |
| return rc; |
| } |
| |
| rc = qpnp_led_masked_write(led, LED_MPP_SINK_CTRL(led->base), |
| LED_MPP_SINK_MASK, val); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write sink control reg\n"); |
| return rc; |
| } |
| |
| if (led->mpp_cfg->pwm_mode != MANUAL_MODE) { |
| rc = qpnp_pwm_init(led->mpp_cfg->pwm_cfg, led->pdev, |
| led->cdev.name); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to initialize pwm\n"); |
| return rc; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_gpio_init(struct qpnp_led_data *led) |
| { |
| int rc; |
| |
| rc = qpnp_led_masked_write(led, LED_GPIO_VIN_CTRL(led->base), |
| LED_GPIO_VIN_MASK, led->gpio_cfg->vin_ctrl); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Failed to write led vin control reg\n"); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_led_initialize(struct qpnp_led_data *led) |
| { |
| int rc = 0; |
| |
| switch (led->id) { |
| case QPNP_ID_WLED: |
| rc = qpnp_wled_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "WLED initialize failed(%d)\n", rc); |
| break; |
| case QPNP_ID_FLASH1_LED0: |
| case QPNP_ID_FLASH1_LED1: |
| rc = qpnp_flash_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "FLASH initialize failed(%d)\n", rc); |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| rc = qpnp_rgb_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "RGB initialize failed(%d)\n", rc); |
| break; |
| case QPNP_ID_LED_MPP: |
| rc = qpnp_mpp_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "MPP initialize failed(%d)\n", rc); |
| break; |
| case QPNP_ID_LED_GPIO: |
| rc = qpnp_gpio_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "GPIO initialize failed(%d)\n", rc); |
| break; |
| case QPNP_ID_KPDBL: |
| rc = qpnp_kpdbl_init(led); |
| if (rc) |
| dev_err(&led->pdev->dev, |
| "KPDBL initialize failed(%d)\n", rc); |
| break; |
| default: |
| dev_err(&led->pdev->dev, "Invalid LED(%d)\n", led->id); |
| return -EINVAL; |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_get_common_configs(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| int rc; |
| u32 val; |
| const char *temp_string; |
| |
| led->cdev.default_trigger = LED_TRIGGER_DEFAULT; |
| rc = of_property_read_string(node, "linux,default-trigger", |
| &temp_string); |
| if (!rc) |
| led->cdev.default_trigger = temp_string; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->default_on = false; |
| rc = of_property_read_string(node, "qcom,default-state", |
| &temp_string); |
| if (!rc) { |
| if (strcmp(temp_string, "on") == 0) |
| led->default_on = true; |
| } else if (rc != -EINVAL) |
| return rc; |
| |
| led->turn_off_delay_ms = 0; |
| rc = of_property_read_u32(node, "qcom,turn-off-delay-ms", &val); |
| if (!rc) |
| led->turn_off_delay_ms = val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| return 0; |
| } |
| |
| /* |
| * Handlers for alternative sources of platform_data |
| */ |
| static int qpnp_get_config_wled(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| u32 val; |
| uint tmp; |
| int rc; |
| |
| led->wled_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct wled_config_data), GFP_KERNEL); |
| if (!led->wled_cfg) |
| return -ENOMEM; |
| |
| rc = regmap_read(led->regmap, PMIC_VERSION_REG, &tmp); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read pmic ver, rc(%d)\n", rc); |
| } |
| led->wled_cfg->pmic_version = (u8)tmp; |
| |
| led->wled_cfg->num_strings = WLED_DEFAULT_STRINGS; |
| rc = of_property_read_u32(node, "qcom,num-strings", &val); |
| if (!rc) |
| led->wled_cfg->num_strings = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->num_physical_strings = led->wled_cfg->num_strings; |
| rc = of_property_read_u32(node, "qcom,num-physical-strings", &val); |
| if (!rc) |
| led->wled_cfg->num_physical_strings = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->ovp_val = WLED_DEFAULT_OVP_VAL; |
| rc = of_property_read_u32(node, "qcom,ovp-val", &val); |
| if (!rc) |
| led->wled_cfg->ovp_val = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->boost_curr_lim = WLED_BOOST_LIM_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,boost-curr-lim", &val); |
| if (!rc) |
| led->wled_cfg->boost_curr_lim = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->cp_select = WLED_CP_SEL_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,cp-sel", &val); |
| if (!rc) |
| led->wled_cfg->cp_select = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->ctrl_delay_us = WLED_CTRL_DLY_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,ctrl-delay-us", &val); |
| if (!rc) |
| led->wled_cfg->ctrl_delay_us = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->op_fdbck = WLED_OP_FDBCK_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,op-fdbck", &val); |
| if (!rc) |
| led->wled_cfg->op_fdbck = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->switch_freq = WLED_SWITCH_FREQ_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,switch-freq", &val); |
| if (!rc) |
| led->wled_cfg->switch_freq = (u8) val; |
| else if (rc != -EINVAL) |
| return rc; |
| |
| led->wled_cfg->dig_mod_gen_en = |
| of_property_read_bool(node, "qcom,dig-mod-gen-en"); |
| |
| led->wled_cfg->cs_out_en = |
| of_property_read_bool(node, "qcom,cs-out-en"); |
| |
| return 0; |
| } |
| |
| static int qpnp_get_config_flash(struct qpnp_led_data *led, |
| struct device_node *node, bool *reg_set) |
| { |
| int rc; |
| u32 val; |
| uint tmp; |
| |
| led->flash_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct flash_config_data), GFP_KERNEL); |
| if (!led->flash_cfg) |
| return -ENOMEM; |
| |
| rc = regmap_read(led->regmap, FLASH_PERIPHERAL_SUBTYPE(led->base), |
| &tmp); |
| if (rc) { |
| dev_err(&led->pdev->dev, |
| "Unable to read from addr=%x, rc(%d)\n", |
| FLASH_PERIPHERAL_SUBTYPE(led->base), rc); |
| } |
| led->flash_cfg->peripheral_subtype = (u8)tmp; |
| |
| led->flash_cfg->torch_enable = |
| of_property_read_bool(node, "qcom,torch-enable"); |
| |
| led->flash_cfg->no_smbb_support = |
| of_property_read_bool(node, "qcom,no-smbb-support"); |
| |
| if (of_find_property(of_get_parent(node), "flash-wa-supply", |
| NULL) && (!*reg_set)) { |
| led->flash_cfg->flash_wa_reg = |
| devm_regulator_get(&led->pdev->dev, "flash-wa"); |
| if (IS_ERR_OR_NULL(led->flash_cfg->flash_wa_reg)) { |
| rc = PTR_ERR(led->flash_cfg->flash_wa_reg); |
| if (rc != EPROBE_DEFER) { |
| dev_err(&led->pdev->dev, |
| "Flash wa regulator get failed(%d)\n", |
| rc); |
| } |
| } else { |
| led->flash_cfg->flash_wa_reg_get = true; |
| } |
| } |
| |
| if (led->id == QPNP_ID_FLASH1_LED0) { |
| led->flash_cfg->enable_module = FLASH_ENABLE_LED_0; |
| led->flash_cfg->current_addr = FLASH_LED_0_CURR(led->base); |
| led->flash_cfg->trigger_flash = FLASH_LED_0_OUTPUT; |
| if (!*reg_set) { |
| led->flash_cfg->flash_boost_reg = |
| regulator_get(&led->pdev->dev, |
| "flash-boost"); |
| if (IS_ERR(led->flash_cfg->flash_boost_reg)) { |
| rc = PTR_ERR(led->flash_cfg->flash_boost_reg); |
| dev_err(&led->pdev->dev, |
| "Regulator get failed(%d)\n", rc); |
| goto error_get_flash_reg; |
| } |
| led->flash_cfg->flash_reg_get = true; |
| *reg_set = true; |
| } else |
| led->flash_cfg->flash_reg_get = false; |
| |
| if (led->flash_cfg->torch_enable) { |
| led->flash_cfg->second_addr = |
| FLASH_LED_1_CURR(led->base); |
| } |
| } else if (led->id == QPNP_ID_FLASH1_LED1) { |
| led->flash_cfg->enable_module = FLASH_ENABLE_LED_1; |
| led->flash_cfg->current_addr = FLASH_LED_1_CURR(led->base); |
| led->flash_cfg->trigger_flash = FLASH_LED_1_OUTPUT; |
| if (!*reg_set) { |
| led->flash_cfg->flash_boost_reg = |
| regulator_get(&led->pdev->dev, |
| "flash-boost"); |
| if (IS_ERR(led->flash_cfg->flash_boost_reg)) { |
| rc = PTR_ERR(led->flash_cfg->flash_boost_reg); |
| dev_err(&led->pdev->dev, |
| "Regulator get failed(%d)\n", rc); |
| goto error_get_flash_reg; |
| } |
| led->flash_cfg->flash_reg_get = true; |
| *reg_set = true; |
| } else |
| led->flash_cfg->flash_reg_get = false; |
| |
| if (led->flash_cfg->torch_enable) { |
| led->flash_cfg->second_addr = |
| FLASH_LED_0_CURR(led->base); |
| } |
| } else { |
| dev_err(&led->pdev->dev, "Unknown flash LED name given\n"); |
| return -EINVAL; |
| } |
| |
| if (led->flash_cfg->torch_enable) { |
| if (of_find_property(of_get_parent(node), "torch-boost-supply", |
| NULL)) { |
| if (!led->flash_cfg->no_smbb_support) { |
| led->flash_cfg->torch_boost_reg = |
| regulator_get(&led->pdev->dev, |
| "torch-boost"); |
| if (IS_ERR(led->flash_cfg->torch_boost_reg)) { |
| rc = PTR_ERR(led->flash_cfg-> |
| torch_boost_reg); |
| dev_err(&led->pdev->dev, |
| "Torch regulator get failed(%d)\n", rc); |
| goto error_get_torch_reg; |
| } |
| } |
| led->flash_cfg->enable_module = FLASH_ENABLE_MODULE; |
| } else |
| led->flash_cfg->enable_module = FLASH_ENABLE_ALL; |
| led->flash_cfg->trigger_flash = FLASH_TORCH_OUTPUT; |
| |
| rc = of_property_read_u32(node, "qcom,duration", &val); |
| if (!rc) |
| led->flash_cfg->duration = ((u8) val) - 2; |
| else if (rc == -EINVAL) |
| led->flash_cfg->duration = TORCH_DURATION_12s; |
| else { |
| if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_SINGLE) |
| goto error_get_flash_reg; |
| else if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_DUAL) |
| goto error_get_torch_reg; |
| } |
| |
| rc = of_property_read_u32(node, "qcom,current", &val); |
| if (!rc) |
| led->flash_cfg->current_prgm = (val * |
| TORCH_MAX_LEVEL / led->max_current); |
| else { |
| if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_SINGLE) |
| goto error_get_flash_reg; |
| else if (led->flash_cfg->peripheral_subtype == |
| FLASH_SUBTYPE_DUAL) |
| goto error_get_torch_reg; |
| goto error_get_torch_reg; |
| } |
| |
| return 0; |
| } |
| |
| rc = of_property_read_u32(node, "qcom,duration", &val); |
| if (!rc) |
| led->flash_cfg->duration = (u8)((val - 10) / 10); |
| else if (rc == -EINVAL) |
| led->flash_cfg->duration = FLASH_DURATION_200ms; |
| else |
| goto error_get_flash_reg; |
| |
| rc = of_property_read_u32(node, "qcom,current", &val); |
| if (!rc) |
| led->flash_cfg->current_prgm = val * FLASH_MAX_LEVEL |
| / led->max_current; |
| else |
| goto error_get_flash_reg; |
| |
| rc = of_property_read_u32(node, "qcom,headroom", &val); |
| if (!rc) |
| led->flash_cfg->headroom = (u8) val; |
| else if (rc == -EINVAL) |
| led->flash_cfg->headroom = HEADROOM_500mV; |
| else |
| goto error_get_flash_reg; |
| |
| rc = of_property_read_u32(node, "qcom,clamp-curr", &val); |
| if (!rc) |
| led->flash_cfg->clamp_curr = (val * |
| FLASH_MAX_LEVEL / led->max_current); |
| else if (rc == -EINVAL) |
| led->flash_cfg->clamp_curr = FLASH_CLAMP_200mA; |
| else |
| goto error_get_flash_reg; |
| |
| rc = of_property_read_u32(node, "qcom,startup-dly", &val); |
| if (!rc) |
| led->flash_cfg->startup_dly = (u8) val; |
| else if (rc == -EINVAL) |
| led->flash_cfg->startup_dly = DELAY_128us; |
| else |
| goto error_get_flash_reg; |
| |
| led->flash_cfg->safety_timer = |
| of_property_read_bool(node, "qcom,safety-timer"); |
| |
| led->flash_cfg->vreg_ok = |
| of_property_read_bool(node, "qcom,sw_vreg_ok"); |
| |
| return 0; |
| |
| error_get_torch_reg: |
| if (led->flash_cfg->no_smbb_support) |
| regulator_put(led->flash_cfg->flash_boost_reg); |
| else |
| regulator_put(led->flash_cfg->torch_boost_reg); |
| |
| error_get_flash_reg: |
| regulator_put(led->flash_cfg->flash_boost_reg); |
| return rc; |
| |
| } |
| |
| static int qpnp_get_config_pwm(struct pwm_config_data *pwm_cfg, |
| struct platform_device *pdev, |
| struct device_node *node) |
| { |
| struct property *prop; |
| int rc, i, lut_max_size; |
| u32 val; |
| u8 *temp_cfg; |
| const char *led_label; |
| |
| pwm_cfg->pwm_dev = of_pwm_get(node, NULL); |
| |
| if (IS_ERR(pwm_cfg->pwm_dev)) { |
| rc = PTR_ERR(pwm_cfg->pwm_dev); |
| dev_err(&pdev->dev, "Cannot get PWM device rc:(%d)\n", rc); |
| pwm_cfg->pwm_dev = NULL; |
| return rc; |
| } |
| |
| if (pwm_cfg->mode != MANUAL_MODE) { |
| rc = of_property_read_u32(node, "qcom,pwm-us", &val); |
| if (!rc) |
| pwm_cfg->pwm_period_us = val; |
| else |
| return rc; |
| } |
| |
| pwm_cfg->use_blink = |
| of_property_read_bool(node, "qcom,use-blink"); |
| |
| if (pwm_cfg->mode == LPG_MODE || pwm_cfg->use_blink) { |
| pwm_cfg->duty_cycles = |
| devm_kzalloc(&pdev->dev, |
| sizeof(struct pwm_duty_cycles), GFP_KERNEL); |
| if (!pwm_cfg->duty_cycles) { |
| dev_err(&pdev->dev, "Unable to allocate memory\n"); |
| rc = -ENOMEM; |
| goto bad_lpg_params; |
| } |
| |
| prop = of_find_property(node, "qcom,duty-pcts", |
| &pwm_cfg->duty_cycles->num_duty_pcts); |
| if (!prop) { |
| dev_err(&pdev->dev, "Looking up property node qcom,duty-pcts failed\n"); |
| rc = -ENODEV; |
| goto bad_lpg_params; |
| } else if (!pwm_cfg->duty_cycles->num_duty_pcts) { |
| dev_err(&pdev->dev, "Invalid length of duty pcts\n"); |
| rc = -EINVAL; |
| goto bad_lpg_params; |
| } |
| |
| rc = of_property_read_string(node, "label", &led_label); |
| |
| if (rc < 0) { |
| dev_err(&pdev->dev, |
| "Failure reading label, rc = %d\n", rc); |
| return rc; |
| } |
| |
| if (strcmp(led_label, "kpdbl") == 0) |
| lut_max_size = PWM_GPLED_LUT_MAX_SIZE; |
| else |
| lut_max_size = PWM_LUT_MAX_SIZE; |
| |
| pwm_cfg->duty_cycles->duty_pcts = |
| devm_kzalloc(&pdev->dev, |
| sizeof(int) * lut_max_size, |
| GFP_KERNEL); |
| if (!pwm_cfg->duty_cycles->duty_pcts) { |
| dev_err(&pdev->dev, "Unable to allocate memory\n"); |
| rc = -ENOMEM; |
| goto bad_lpg_params; |
| } |
| |
| pwm_cfg->old_duty_pcts = |
| devm_kzalloc(&pdev->dev, |
| sizeof(int) * lut_max_size, |
| GFP_KERNEL); |
| if (!pwm_cfg->old_duty_pcts) { |
| dev_err(&pdev->dev, "Unable to allocate memory\n"); |
| rc = -ENOMEM; |
| goto bad_lpg_params; |
| } |
| |
| temp_cfg = devm_kzalloc(&pdev->dev, |
| pwm_cfg->duty_cycles->num_duty_pcts * |
| sizeof(u8), GFP_KERNEL); |
| if (!temp_cfg) { |
| dev_err(&pdev->dev, "Failed to allocate memory for duty pcts\n"); |
| rc = -ENOMEM; |
| goto bad_lpg_params; |
| } |
| |
| memcpy(temp_cfg, prop->value, |
| pwm_cfg->duty_cycles->num_duty_pcts); |
| |
| for (i = 0; i < pwm_cfg->duty_cycles->num_duty_pcts; i++) |
| pwm_cfg->duty_cycles->duty_pcts[i] = |
| (int) temp_cfg[i]; |
| |
| rc = of_property_read_u32(node, "qcom,start-idx", &val); |
| if (!rc) { |
| pwm_cfg->lut_params.start_idx = val; |
| pwm_cfg->duty_cycles->start_idx = val; |
| } else |
| goto bad_lpg_params; |
| |
| pwm_cfg->lut_params.lut_pause_hi = 0; |
| rc = of_property_read_u32(node, "qcom,pause-hi", &val); |
| if (!rc) |
| pwm_cfg->lut_params.lut_pause_hi = val; |
| else if (rc != -EINVAL) |
| goto bad_lpg_params; |
| |
| pwm_cfg->lut_params.lut_pause_lo = 0; |
| rc = of_property_read_u32(node, "qcom,pause-lo", &val); |
| if (!rc) |
| pwm_cfg->lut_params.lut_pause_lo = val; |
| else if (rc != -EINVAL) |
| goto bad_lpg_params; |
| |
| pwm_cfg->lut_params.ramp_step_ms = |
| QPNP_LUT_RAMP_STEP_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,ramp-step-ms", &val); |
| if (!rc) |
| pwm_cfg->lut_params.ramp_step_ms = val; |
| else if (rc != -EINVAL) |
| goto bad_lpg_params; |
| |
| pwm_cfg->lut_params.flags = QPNP_LED_PWM_FLAGS; |
| rc = of_property_read_u32(node, "qcom,lut-flags", &val); |
| if (!rc) |
| pwm_cfg->lut_params.flags = (u8) val; |
| else if (rc != -EINVAL) |
| goto bad_lpg_params; |
| |
| pwm_cfg->lut_params.idx_len = |
| pwm_cfg->duty_cycles->num_duty_pcts; |
| } |
| return 0; |
| |
| bad_lpg_params: |
| pwm_cfg->use_blink = false; |
| if (pwm_cfg->mode == PWM_MODE) { |
| dev_err(&pdev->dev, "LPG parameters not set for blink mode, defaulting to PWM mode\n"); |
| return 0; |
| } |
| return rc; |
| }; |
| |
| static int qpnp_led_get_mode(const char *mode) |
| { |
| if (strcmp(mode, "manual") == 0) |
| return MANUAL_MODE; |
| else if (strcmp(mode, "pwm") == 0) |
| return PWM_MODE; |
| else if (strcmp(mode, "lpg") == 0) |
| return LPG_MODE; |
| else |
| return -EINVAL; |
| }; |
| |
| static int qpnp_get_config_kpdbl(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| int rc; |
| u32 val; |
| u8 led_mode; |
| const char *mode; |
| |
| led->kpdbl_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct kpdbl_config_data), GFP_KERNEL); |
| if (!led->kpdbl_cfg) |
| return -ENOMEM; |
| |
| rc = of_property_read_string(node, "qcom,mode", &mode); |
| if (!rc) { |
| led_mode = qpnp_led_get_mode(mode); |
| if ((led_mode == MANUAL_MODE) || (led_mode == -EINVAL)) { |
| dev_err(&led->pdev->dev, "Selected mode not supported for kpdbl.\n"); |
| return -EINVAL; |
| } |
| led->kpdbl_cfg->pwm_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct pwm_config_data), |
| GFP_KERNEL); |
| if (!led->kpdbl_cfg->pwm_cfg) |
| return -ENOMEM; |
| |
| led->kpdbl_cfg->pwm_cfg->mode = led_mode; |
| led->kpdbl_cfg->pwm_cfg->default_mode = led_mode; |
| } else { |
| return rc; |
| } |
| |
| rc = qpnp_get_config_pwm(led->kpdbl_cfg->pwm_cfg, led->pdev, node); |
| if (rc < 0) { |
| if (led->kpdbl_cfg->pwm_cfg->pwm_dev) |
| pwm_put(led->kpdbl_cfg->pwm_cfg->pwm_dev); |
| return rc; |
| } |
| |
| rc = of_property_read_u32(node, "qcom,row-id", &val); |
| if (!rc) |
| led->kpdbl_cfg->row_id = val; |
| else |
| return rc; |
| |
| led->kpdbl_cfg->row_src_vbst = |
| of_property_read_bool(node, "qcom,row-src-vbst"); |
| |
| led->kpdbl_cfg->row_src_en = |
| of_property_read_bool(node, "qcom,row-src-en"); |
| |
| led->kpdbl_cfg->always_on = |
| of_property_read_bool(node, "qcom,always-on"); |
| |
| return 0; |
| } |
| |
| static int qpnp_get_config_rgb(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| int rc; |
| u8 led_mode; |
| const char *mode; |
| |
| led->rgb_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct rgb_config_data), GFP_KERNEL); |
| if (!led->rgb_cfg) |
| return -ENOMEM; |
| |
| if (led->id == QPNP_ID_RGB_RED) |
| led->rgb_cfg->enable = RGB_LED_ENABLE_RED; |
| else if (led->id == QPNP_ID_RGB_GREEN) |
| led->rgb_cfg->enable = RGB_LED_ENABLE_GREEN; |
| else if (led->id == QPNP_ID_RGB_BLUE) |
| led->rgb_cfg->enable = RGB_LED_ENABLE_BLUE; |
| else |
| return -EINVAL; |
| |
| rc = of_property_read_string(node, "qcom,mode", &mode); |
| if (!rc) { |
| led_mode = qpnp_led_get_mode(mode); |
| if ((led_mode == MANUAL_MODE) || (led_mode == -EINVAL)) { |
| dev_err(&led->pdev->dev, "Selected mode not supported for rgb\n"); |
| return -EINVAL; |
| } |
| led->rgb_cfg->pwm_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct pwm_config_data), |
| GFP_KERNEL); |
| if (!led->rgb_cfg->pwm_cfg) { |
| dev_err(&led->pdev->dev, |
| "Unable to allocate memory\n"); |
| return -ENOMEM; |
| } |
| led->rgb_cfg->pwm_cfg->mode = led_mode; |
| led->rgb_cfg->pwm_cfg->default_mode = led_mode; |
| } else { |
| return rc; |
| } |
| |
| rc = qpnp_get_config_pwm(led->rgb_cfg->pwm_cfg, led->pdev, node); |
| if (rc < 0) { |
| if (led->rgb_cfg->pwm_cfg->pwm_dev) |
| pwm_put(led->rgb_cfg->pwm_cfg->pwm_dev); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int qpnp_get_config_mpp(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| int rc; |
| u32 val; |
| u8 led_mode; |
| const char *mode; |
| |
| led->mpp_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct mpp_config_data), GFP_KERNEL); |
| if (!led->mpp_cfg) |
| return -ENOMEM; |
| |
| if (of_find_property(of_get_parent(node), "mpp-power-supply", NULL)) { |
| led->mpp_cfg->mpp_reg = |
| regulator_get(&led->pdev->dev, |
| "mpp-power"); |
| if (IS_ERR(led->mpp_cfg->mpp_reg)) { |
| rc = PTR_ERR(led->mpp_cfg->mpp_reg); |
| dev_err(&led->pdev->dev, |
| "MPP regulator get failed(%d)\n", rc); |
| return rc; |
| } |
| } |
| |
| if (led->mpp_cfg->mpp_reg) { |
| rc = of_property_read_u32(of_get_parent(node), |
| "qcom,mpp-power-max-voltage", &val); |
| if (!rc) |
| led->mpp_cfg->max_uV = val; |
| else |
| goto err_config_mpp; |
| |
| rc = of_property_read_u32(of_get_parent(node), |
| "qcom,mpp-power-min-voltage", &val); |
| if (!rc) |
| led->mpp_cfg->min_uV = val; |
| else |
| goto err_config_mpp; |
| } else { |
| rc = of_property_read_u32(of_get_parent(node), |
| "qcom,mpp-power-max-voltage", &val); |
| if (!rc) |
| dev_warn(&led->pdev->dev, "No regulator specified\n"); |
| |
| rc = of_property_read_u32(of_get_parent(node), |
| "qcom,mpp-power-min-voltage", &val); |
| if (!rc) |
| dev_warn(&led->pdev->dev, "No regulator specified\n"); |
| } |
| |
| led->mpp_cfg->current_setting = LED_MPP_CURRENT_MIN; |
| rc = of_property_read_u32(node, "qcom,current-setting", &val); |
| if (!rc) { |
| if (led->mpp_cfg->current_setting < LED_MPP_CURRENT_MIN) |
| led->mpp_cfg->current_setting = LED_MPP_CURRENT_MIN; |
| else if (led->mpp_cfg->current_setting > LED_MPP_CURRENT_MAX) |
| led->mpp_cfg->current_setting = LED_MPP_CURRENT_MAX; |
| else |
| led->mpp_cfg->current_setting = (u8) val; |
| } else if (rc != -EINVAL) |
| goto err_config_mpp; |
| |
| led->mpp_cfg->source_sel = LED_MPP_SOURCE_SEL_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,source-sel", &val); |
| if (!rc) |
| led->mpp_cfg->source_sel = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_mpp; |
| |
| led->mpp_cfg->mode_ctrl = LED_MPP_MODE_SINK; |
| rc = of_property_read_u32(node, "qcom,mode-ctrl", &val); |
| if (!rc) |
| led->mpp_cfg->mode_ctrl = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_mpp; |
| |
| led->mpp_cfg->vin_ctrl = LED_MPP_VIN_CTRL_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,vin-ctrl", &val); |
| if (!rc) |
| led->mpp_cfg->vin_ctrl = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_mpp; |
| |
| led->mpp_cfg->min_brightness = 0; |
| rc = of_property_read_u32(node, "qcom,min-brightness", &val); |
| if (!rc) |
| led->mpp_cfg->min_brightness = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_mpp; |
| |
| rc = of_property_read_string(node, "qcom,mode", &mode); |
| if (!rc) { |
| led_mode = qpnp_led_get_mode(mode); |
| led->mpp_cfg->pwm_mode = led_mode; |
| if (led_mode == MANUAL_MODE) |
| return MANUAL_MODE; |
| else if (led_mode == -EINVAL) { |
| dev_err(&led->pdev->dev, "Selected mode not supported for mpp\n"); |
| rc = -EINVAL; |
| goto err_config_mpp; |
| } |
| led->mpp_cfg->pwm_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct pwm_config_data), |
| GFP_KERNEL); |
| if (!led->mpp_cfg->pwm_cfg) { |
| dev_err(&led->pdev->dev, |
| "Unable to allocate memory\n"); |
| rc = -ENOMEM; |
| goto err_config_mpp; |
| } |
| led->mpp_cfg->pwm_cfg->mode = led_mode; |
| led->mpp_cfg->pwm_cfg->default_mode = led_mode; |
| } else { |
| return rc; |
| } |
| |
| rc = qpnp_get_config_pwm(led->mpp_cfg->pwm_cfg, led->pdev, node); |
| if (rc < 0) { |
| if (led->mpp_cfg->pwm_cfg && led->mpp_cfg->pwm_cfg->pwm_dev) |
| pwm_put(led->mpp_cfg->pwm_cfg->pwm_dev); |
| goto err_config_mpp; |
| } |
| |
| return 0; |
| |
| err_config_mpp: |
| if (led->mpp_cfg->mpp_reg) |
| regulator_put(led->mpp_cfg->mpp_reg); |
| return rc; |
| } |
| |
| static int qpnp_get_config_gpio(struct qpnp_led_data *led, |
| struct device_node *node) |
| { |
| int rc; |
| u32 val; |
| |
| led->gpio_cfg = devm_kzalloc(&led->pdev->dev, |
| sizeof(struct gpio_config_data), GFP_KERNEL); |
| if (!led->gpio_cfg) |
| return -ENOMEM; |
| |
| led->gpio_cfg->source_sel = LED_GPIO_SOURCE_SEL_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,source-sel", &val); |
| if (!rc) |
| led->gpio_cfg->source_sel = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_gpio; |
| |
| led->gpio_cfg->mode_ctrl = LED_GPIO_MODE_OUTPUT; |
| rc = of_property_read_u32(node, "qcom,mode-ctrl", &val); |
| if (!rc) |
| led->gpio_cfg->mode_ctrl = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_gpio; |
| |
| led->gpio_cfg->vin_ctrl = LED_GPIO_VIN_CTRL_DEFAULT; |
| rc = of_property_read_u32(node, "qcom,vin-ctrl", &val); |
| if (!rc) |
| led->gpio_cfg->vin_ctrl = (u8) val; |
| else if (rc != -EINVAL) |
| goto err_config_gpio; |
| |
| return 0; |
| |
| err_config_gpio: |
| return rc; |
| } |
| |
| static int qpnp_leds_probe(struct platform_device *pdev) |
| { |
| struct qpnp_led_data *led, *led_array; |
| unsigned int base; |
| struct device_node *node, *temp; |
| int rc, i, num_leds = 0, parsed_leds = 0; |
| const char *led_label; |
| bool regulator_probe = false; |
| |
| node = pdev->dev.of_node; |
| if (node == NULL) |
| return -ENODEV; |
| |
| temp = NULL; |
| while ((temp = of_get_next_child(node, temp))) |
| num_leds++; |
| |
| if (!num_leds) |
| return -ECHILD; |
| |
| led_array = devm_kcalloc(&pdev->dev, num_leds, sizeof(*led_array), |
| GFP_KERNEL); |
| if (!led_array) |
| return -ENOMEM; |
| |
| for_each_child_of_node(node, temp) { |
| led = &led_array[parsed_leds]; |
| led->num_leds = num_leds; |
| led->regmap = dev_get_regmap(pdev->dev.parent, NULL); |
| if (!led->regmap) { |
| dev_err(&pdev->dev, "Couldn't get parent's regmap\n"); |
| return -EINVAL; |
| } |
| led->pdev = pdev; |
| |
| rc = of_property_read_u32(pdev->dev.of_node, "reg", &base); |
| if (rc < 0) { |
| dev_err(&pdev->dev, |
| "Couldn't find reg in node = %s rc = %d\n", |
| pdev->dev.of_node->full_name, rc); |
| goto fail_id_check; |
| } |
| led->base = base; |
| |
| rc = of_property_read_string(temp, "label", &led_label); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failure reading label, rc = %d\n", rc); |
| goto fail_id_check; |
| } |
| |
| rc = of_property_read_string(temp, "linux,name", |
| &led->cdev.name); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failure reading led name, rc = %d\n", rc); |
| goto fail_id_check; |
| } |
| |
| rc = of_property_read_u32(temp, "qcom,max-current", |
| &led->max_current); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failure reading max_current, rc = %d\n", rc); |
| goto fail_id_check; |
| } |
| |
| rc = of_property_read_u32(temp, "qcom,id", &led->id); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Failure reading led id, rc = %d\n", rc); |
| goto fail_id_check; |
| } |
| |
| rc = qpnp_get_common_configs(led, temp); |
| if (rc) { |
| dev_err(&led->pdev->dev, "Failure reading common led configuration, rc = %d\n", |
| rc); |
| goto fail_id_check; |
| } |
| |
| led->cdev.brightness_set = qpnp_led_set; |
| led->cdev.brightness_get = qpnp_led_get; |
| |
| if (strcmp(led_label, "wled") == 0) { |
| rc = qpnp_get_config_wled(led, temp); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read wled config data\n"); |
| goto fail_id_check; |
| } |
| } else if (strcmp(led_label, "flash") == 0) { |
| if (!of_find_property(node, "flash-boost-supply", NULL)) |
| regulator_probe = true; |
| rc = qpnp_get_config_flash(led, temp, ®ulator_probe); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read flash config data\n"); |
| goto fail_id_check; |
| } |
| } else if (strcmp(led_label, "rgb") == 0) { |
| rc = qpnp_get_config_rgb(led, temp); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read rgb config data\n"); |
| goto fail_id_check; |
| } |
| } else if (strcmp(led_label, "mpp") == 0) { |
| rc = qpnp_get_config_mpp(led, temp); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read mpp config data\n"); |
| goto fail_id_check; |
| } |
| } else if (strcmp(led_label, "gpio") == 0) { |
| rc = qpnp_get_config_gpio(led, temp); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read gpio config data\n"); |
| goto fail_id_check; |
| } |
| } else if (strcmp(led_label, "kpdbl") == 0) { |
| bitmap_zero(kpdbl_leds_in_use, NUM_KPDBL_LEDS); |
| is_kpdbl_master_turn_on = false; |
| rc = qpnp_get_config_kpdbl(led, temp); |
| if (rc < 0) { |
| dev_err(&led->pdev->dev, |
| "Unable to read kpdbl config data\n"); |
| goto fail_id_check; |
| } |
| } else { |
| dev_err(&led->pdev->dev, "No LED matching label\n"); |
| rc = -EINVAL; |
| goto fail_id_check; |
| } |
| |
| if (led->id != QPNP_ID_FLASH1_LED0 && |
| led->id != QPNP_ID_FLASH1_LED1) |
| mutex_init(&led->lock); |
| |
| led->in_order_command_processing = of_property_read_bool |
| (temp, "qcom,in-order-command-processing"); |
| |
| if (led->in_order_command_processing) { |
| /* |
| * the command order from user space needs to be |
| * maintained use ordered workqueue to prevent |
| * concurrency |
| */ |
| led->workqueue = alloc_ordered_workqueue |
| ("led_workqueue", 0); |
| if (!led->workqueue) { |
| rc = -ENOMEM; |
| goto fail_id_check; |
| } |
| } |
| |
| INIT_WORK(&led->work, qpnp_led_work); |
| |
| rc = qpnp_led_initialize(led); |
| if (rc < 0) |
| goto fail_id_check; |
| |
| rc = qpnp_led_set_max_brightness(led); |
| if (rc < 0) |
| goto fail_id_check; |
| |
| rc = led_classdev_register(&pdev->dev, &led->cdev); |
| if (rc) { |
| dev_err(&pdev->dev, |
| "unable to register led %d,rc=%d\n", |
| led->id, rc); |
| goto fail_id_check; |
| } |
| |
| if (led->id == QPNP_ID_FLASH1_LED0 || |
| led->id == QPNP_ID_FLASH1_LED1) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &led_attr_group); |
| if (rc) |
| goto fail_id_check; |
| |
| } |
| |
| if (led->id == QPNP_ID_LED_MPP) { |
| if (!led->mpp_cfg->pwm_cfg) |
| break; |
| if (led->mpp_cfg->pwm_cfg->mode == PWM_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &pwm_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| if (led->mpp_cfg->pwm_cfg->use_blink) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &blink_attr_group); |
| if (rc) |
| goto fail_id_check; |
| |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } else if (led->mpp_cfg->pwm_cfg->mode == LPG_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| } else if ((led->id == QPNP_ID_RGB_RED) || |
| (led->id == QPNP_ID_RGB_GREEN) || |
| (led->id == QPNP_ID_RGB_BLUE)) { |
| if (led->rgb_cfg->pwm_cfg->mode == PWM_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &pwm_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| if (led->rgb_cfg->pwm_cfg->use_blink) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &blink_attr_group); |
| if (rc) |
| goto fail_id_check; |
| |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } else if (led->rgb_cfg->pwm_cfg->mode == LPG_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| } else if (led->id == QPNP_ID_KPDBL) { |
| if (led->kpdbl_cfg->pwm_cfg->mode == PWM_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &pwm_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| if (led->kpdbl_cfg->pwm_cfg->use_blink) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &blink_attr_group); |
| if (rc) |
| goto fail_id_check; |
| |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } else if (led->kpdbl_cfg->pwm_cfg->mode == LPG_MODE) { |
| rc = sysfs_create_group(&led->cdev.dev->kobj, |
| &lpg_attr_group); |
| if (rc) |
| goto fail_id_check; |
| } |
| } |
| |
| /* configure default state */ |
| if (led->default_on) { |
| led->cdev.brightness = led->cdev.max_brightness; |
| __qpnp_led_work(led, led->cdev.brightness); |
| if (led->turn_off_delay_ms > 0) |
| qpnp_led_turn_off(led); |
| } else |
| led->cdev.brightness = LED_OFF; |
| |
| parsed_leds++; |
| } |
| dev_set_drvdata(&pdev->dev, led_array); |
| return 0; |
| |
| fail_id_check: |
| for (i = 0; i < parsed_leds; i++) { |
| if (led_array[i].id != QPNP_ID_FLASH1_LED0 && |
| led_array[i].id != QPNP_ID_FLASH1_LED1) |
| mutex_destroy(&led_array[i].lock); |
| if (led_array[i].in_order_command_processing) |
| destroy_workqueue(led_array[i].workqueue); |
| led_classdev_unregister(&led_array[i].cdev); |
| } |
| |
| return rc; |
| } |
| |
| static int qpnp_leds_remove(struct platform_device *pdev) |
| { |
| struct qpnp_led_data *led_array = dev_get_drvdata(&pdev->dev); |
| int i, parsed_leds = led_array->num_leds; |
| |
| for (i = 0; i < parsed_leds; i++) { |
| cancel_work_sync(&led_array[i].work); |
| if (led_array[i].id != QPNP_ID_FLASH1_LED0 && |
| led_array[i].id != QPNP_ID_FLASH1_LED1) |
| mutex_destroy(&led_array[i].lock); |
| |
| if (led_array[i].in_order_command_processing) |
| destroy_workqueue(led_array[i].workqueue); |
| led_classdev_unregister(&led_array[i].cdev); |
| switch (led_array[i].id) { |
| case QPNP_ID_WLED: |
| break; |
| case QPNP_ID_FLASH1_LED0: |
| case QPNP_ID_FLASH1_LED1: |
| if (led_array[i].flash_cfg->flash_reg_get) |
| regulator_put( |
| led_array[i].flash_cfg->flash_boost_reg); |
| if (led_array[i].flash_cfg->torch_enable) |
| if (!led_array[i].flash_cfg->no_smbb_support) |
| regulator_put(led_array[i]. |
| flash_cfg->torch_boost_reg); |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &led_attr_group); |
| break; |
| case QPNP_ID_RGB_RED: |
| case QPNP_ID_RGB_GREEN: |
| case QPNP_ID_RGB_BLUE: |
| if (led_array[i].rgb_cfg->pwm_cfg->mode == PWM_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &pwm_attr_group); |
| if (led_array[i].rgb_cfg->pwm_cfg->use_blink) { |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &blink_attr_group); |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| } else if (led_array[i].rgb_cfg->pwm_cfg->mode |
| == LPG_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| break; |
| case QPNP_ID_LED_MPP: |
| if (!led_array[i].mpp_cfg->pwm_cfg) |
| break; |
| if (led_array[i].mpp_cfg->pwm_cfg->mode == PWM_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &pwm_attr_group); |
| if (led_array[i].mpp_cfg->pwm_cfg->use_blink) { |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &blink_attr_group); |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| } else if (led_array[i].mpp_cfg->pwm_cfg->mode |
| == LPG_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| if (led_array[i].mpp_cfg->mpp_reg) |
| regulator_put(led_array[i].mpp_cfg->mpp_reg); |
| break; |
| case QPNP_ID_KPDBL: |
| if (led_array[i].kpdbl_cfg->pwm_cfg->mode == PWM_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &pwm_attr_group); |
| if (led_array[i].kpdbl_cfg->pwm_cfg->use_blink) { |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &blink_attr_group); |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| } else if (led_array[i].kpdbl_cfg->pwm_cfg->mode |
| == LPG_MODE) |
| sysfs_remove_group(&led_array[i].cdev.dev->kobj, |
| &lpg_attr_group); |
| break; |
| default: |
| dev_err(&led_array->pdev->dev, |
| "Invalid LED(%d)\n", |
| led_array[i].id); |
| return -EINVAL; |
| } |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id spmi_match_table[] = { |
| { .compatible = "qcom,leds-qpnp",}, |
| { }, |
| }; |
| #else |
| #define spmi_match_table NULL |
| #endif |
| |
| static struct platform_driver qpnp_leds_driver = { |
| .driver = { |
| .name = "qcom,leds-qpnp", |
| .of_match_table = spmi_match_table, |
| }, |
| .probe = qpnp_leds_probe, |
| .remove = qpnp_leds_remove, |
| }; |
| |
| static int __init qpnp_led_init(void) |
| { |
| return platform_driver_register(&qpnp_leds_driver); |
| } |
| module_init(qpnp_led_init); |
| |
| static void __exit qpnp_led_exit(void) |
| { |
| platform_driver_unregister(&qpnp_leds_driver); |
| } |
| module_exit(qpnp_led_exit); |
| |
| MODULE_DESCRIPTION("QPNP LEDs driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("leds:leds-qpnp"); |
| |