| /* Copyright (c) 2016-2017, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| &spmi_bus { |
| qcom,pm660@0 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm660_revid: qcom,revid@100 { |
| compatible = "qcom,qpnp-revid"; |
| reg = <0x100 0x100>; |
| qcom,fab-id-valid; |
| }; |
| |
| pm660_misc: qcom,misc@900 { |
| compatible = "qcom,qpnp-misc"; |
| reg = <0x900 0x100>; |
| }; |
| |
| qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| interrupts = <0x0 0x8 0x0 IRQ_TYPE_NONE>, |
| <0x0 0x8 0x1 IRQ_TYPE_NONE>, |
| <0x0 0x8 0x4 IRQ_TYPE_NONE>, |
| <0x0 0x8 0x5 IRQ_TYPE_NONE>; |
| interrupt-names = "kpdpwr", "resin", |
| "resin-bark", "kpdpwr-resin-bark"; |
| qcom,pon-dbc-delay = <15625>; |
| qcom,kpdpwr-sw-debounce; |
| qcom,system-reset; |
| qcom,store-hard-reset-reason; |
| |
| qcom,pon_1 { |
| qcom,pon-type = <0>; |
| qcom,pull-up = <1>; |
| linux,code = <116>; |
| }; |
| |
| qcom,pon_2 { |
| qcom,pon-type = <1>; |
| qcom,pull-up = <1>; |
| linux,code = <114>; |
| }; |
| }; |
| |
| qcom,temp-alarm@2400 { |
| compatible = "qcom,qpnp-temp-alarm"; |
| reg = <0x2400 0x100>; |
| interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| label = "pm660_tz"; |
| qcom,channel-num = <6>; |
| qcom,temp_alarm-vadc = <&pm660_vadc>; |
| }; |
| |
| pm660_gpios: pinctrl@c000 { |
| compatible = "qcom,spmi-gpio"; |
| reg = <0xc000 0xd00>; |
| interrupts = <0x0 0xc1 0 IRQ_TYPE_NONE>, |
| <0x0 0xc2 0 IRQ_TYPE_NONE>, |
| <0x0 0xc3 0 IRQ_TYPE_NONE>, |
| <0x0 0xc8 0 IRQ_TYPE_NONE>, |
| <0x0 0xca 0 IRQ_TYPE_NONE>, |
| <0x0 0xcb 0 IRQ_TYPE_NONE>, |
| <0x0 0xcc 0 IRQ_TYPE_NONE>; |
| interrupt-names = "pm660_gpio2", "pm660_gpio3", |
| "pm660_gpio4", "pm660_gpio9", |
| "pm660_gpio11", "pm660_gpio12", |
| "pm660_gpio13"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| qcom,gpios-disallowed = <1 5 6 7 8 10>; |
| }; |
| |
| pm660_coincell: qcom,coincell@2800 { |
| compatible = "qcom,qpnp-coincell"; |
| reg = <0x2800 0x100>; |
| }; |
| |
| pm660_rtc: qcom,pm660_rtc { |
| compatible = "qcom,qpnp-rtc"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| qcom,qpnp-rtc-write = <0>; |
| qcom,qpnp-rtc-alarm-pwrup = <0>; |
| |
| qcom,pm660_rtc_rw@6000 { |
| reg = <0x6000 0x100>; |
| }; |
| qcom,pm660_rtc_alarm@6100 { |
| reg = <0x6100 0x100>; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| }; |
| }; |
| |
| pm660_vadc: vadc@3100 { |
| compatible = "qcom,qpnp-vadc-hc"; |
| reg = <0x3100 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "eoc-int-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1875>; |
| |
| chan@6 { |
| label = "die_temp"; |
| reg = <6>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <3>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| qcom,cal-val = <0>; |
| }; |
| |
| chan@0 { |
| label = "ref_gnd"; |
| reg = <0>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| qcom,cal-val = <0>; |
| }; |
| |
| chan@1 { |
| label = "ref_1250v"; |
| reg = <1>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| qcom,cal-val = <0>; |
| }; |
| |
| chan@83 { |
| label = "vph_pwr"; |
| reg = <0x83>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@85 { |
| label = "vcoin"; |
| reg = <0x85>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@4c { |
| label = "xo_therm"; |
| reg = <0x4c>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <4>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@4d { |
| label = "msm_therm"; |
| reg = <0x4d>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@51 { |
| label = "quiet_therm"; |
| reg = <0x51>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| }; |
| |
| chan@4e { |
| label = "emmc_therm"; |
| reg = <0x4e>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@4f { |
| label = "pa_therm0"; |
| reg = <0x4f>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,fast-avg-setup = <0>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@1d { |
| label = "drax_temp"; |
| reg = <0x1d>; |
| qcom,decimation = <2>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <3>; |
| qcom,hw-settle-time = <0>; |
| qcom,fast-avg-setup = <0>; |
| qcom,cal-val = <0>; |
| }; |
| }; |
| |
| pm660_charger: qcom,qpnp-smb2 { |
| compatible = "qcom,qpnp-smb2"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qcom,pmic-revid = <&pm660_revid>; |
| |
| io-channels = <&pm660_rradc 8>, |
| <&pm660_rradc 10>, |
| <&pm660_rradc 3>, |
| <&pm660_rradc 4>; |
| io-channel-names = "charger_temp", |
| "charger_temp_max", |
| "usbin_i", |
| "usbin_v"; |
| |
| qcom,wipower-max-uw = <5000000>; |
| |
| /* Enable after the qusb_phy0 device node is added */ |
| /* dpdm-supply = <&qusb_phy0>; */ |
| |
| qcom,thermal-mitigation |
| = <3000000 2500000 2000000 1500000 |
| 1000000 500000>; |
| |
| qcom,chgr@1000 { |
| reg = <0x1000 0x100>; |
| interrupts = |
| <0x0 0x10 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x10 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x10 0x2 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x10 0x3 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x10 0x4 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "chg-error", |
| "chg-state-change", |
| "step-chg-state-change", |
| "step-chg-soc-update-fail", |
| "step-chg-soc-update-request"; |
| }; |
| |
| qcom,otg@1100 { |
| reg = <0x1100 0x100>; |
| interrupts = <0x0 0x11 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x11 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x11 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x11 0x3 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "otg-fail", |
| "otg-overcurrent", |
| "otg-oc-dis-sw-sts", |
| "testmode-change-detect"; |
| }; |
| |
| qcom,bat-if@1200 { |
| reg = <0x1200 0x100>; |
| interrupts = |
| <0x0 0x12 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x12 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x12 0x5 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "bat-temp", |
| "bat-ocp", |
| "bat-ov", |
| "bat-low", |
| "bat-therm-or-id-missing", |
| "bat-terminal-missing"; |
| }; |
| |
| qcom,usb-chgpth@1300 { |
| reg = <0x1300 0x100>; |
| interrupts = |
| <0x0 0x13 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x13 0x5 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x13 0x6 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x13 0x7 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "usbin-collapse", |
| "usbin-lt-3p6v", |
| "usbin-uv", |
| "usbin-ov", |
| "usbin-plugin", |
| "usbin-src-change", |
| "usbin-icl-change", |
| "type-c-change"; |
| }; |
| |
| qcom,dc-chgpth@1400 { |
| reg = <0x1400 0x100>; |
| interrupts = |
| <0x0 0x14 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x14 0x6 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "dcin-collapse", |
| "dcin-lt-3p6v", |
| "dcin-uv", |
| "dcin-ov", |
| "dcin-plugin", |
| "div2-en-dg", |
| "dcin-icl-change"; |
| }; |
| |
| qcom,chgr-misc@1600 { |
| reg = <0x1600 0x100>; |
| interrupts = |
| <0x0 0x16 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x16 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x16 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x16 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x16 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x16 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x16 0x6 IRQ_TYPE_EDGE_FALLING>, |
| <0x0 0x16 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "wdog-snarl", |
| "wdog-bark", |
| "aicl-fail", |
| "aicl-done", |
| "high-duty-cycle", |
| "input-current-limiting", |
| "temperature-change", |
| "switcher-power-ok"; |
| }; |
| }; |
| |
| pm660_pdphy: qcom,usb-pdphy@1700 { |
| compatible = "qcom,qpnp-pdphy"; |
| reg = <0x1700 0x100>; |
| vdd-pdphy-supply = <&pm660l_l7>; |
| vbus-supply = <&smb2_vbus>; |
| vconn-supply = <&smb2_vconn>; |
| interrupts = <0x0 0x17 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x2 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x3 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x4 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x5 IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x17 0x6 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "sig-tx", |
| "sig-rx", |
| "msg-tx", |
| "msg-rx", |
| "msg-tx-failed", |
| "msg-tx-discarded", |
| "msg-rx-discarded"; |
| |
| qcom,default-sink-caps = <5000 3000>, /* 5V @ 3A */ |
| <9000 3000>; /* 9V @ 3A */ |
| }; |
| |
| pm660_adc_tm: vadc@3400 { |
| compatible = "qcom,qpnp-adc-tm-hc"; |
| reg = <0x3400 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "eoc-int-en-set"; |
| qcom,adc-bit-resolution = <15>; |
| qcom,adc-vdd-reference = <1875>; |
| qcom,adc_tm-vadc = <&pm660_vadc>; |
| qcom,decimation = <0>; |
| qcom,fast-avg-setup = <0>; |
| #thermal-sensor-cells = <1>; |
| |
| chan@83 { |
| label = "vph_pwr"; |
| reg = <0x83>; |
| qcom,pre-div-channel-scaling = <1>; |
| qcom,calibration-type = "absolute"; |
| qcom,scale-function = <0>; |
| qcom,hw-settle-time = <0>; |
| qcom,btm-channel-number = <0x60>; |
| }; |
| |
| chan@4d { |
| label = "msm_therm"; |
| reg = <0x4d>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,btm-channel-number = <0x68>; |
| qcom,thermal-node; |
| }; |
| |
| chan@51 { |
| label = "quiet_therm"; |
| reg = <0x51>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,btm-channel-number = <0x70>; |
| qcom,thermal-node; |
| }; |
| |
| chan@4c { |
| label = "xo_therm"; |
| reg = <0x4c>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <4>; |
| qcom,hw-settle-time = <2>; |
| qcom,btm-channel-number = <0x78>; |
| qcom,thermal-node; |
| }; |
| |
| chan@4e { |
| label = "emmc_therm"; |
| reg = <0x4e>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,btm-channel-number = <0x80>; |
| qcom,vadc-thermal-node; |
| }; |
| |
| chan@4f { |
| label = "pa_therm0"; |
| reg = <0x4f>; |
| qcom,pre-div-channel-scaling = <0>; |
| qcom,calibration-type = "ratiometric"; |
| qcom,scale-function = <2>; |
| qcom,hw-settle-time = <2>; |
| qcom,btm-channel-number = <0x88>; |
| qcom,vadc-thermal-node; |
| }; |
| }; |
| |
| pm660_rradc: rradc@4500 { |
| compatible = "qcom,rradc"; |
| reg = <0x4500 0x100>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| qcom,pmic-revid = <&pm660_revid>; |
| }; |
| |
| pm660_fg: qpnp,fg { |
| compatible = "qcom,fg-gen3"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| qcom,pmic-revid = <&pm660_revid>; |
| io-channels = <&pm660_rradc 0>, |
| <&pm660_rradc 7>; |
| io-channel-names = "rradc_batt_id", |
| "rradc_die_temp"; |
| qcom,rradc-base = <0x4500>; |
| qcom,fg-esr-timer-awake = <96 96>; |
| qcom,fg-esr-timer-asleep = <256 256>; |
| qcom,fg-esr-timer-charging = <0 96>; |
| qcom,cycle-counter-en; |
| status = "okay"; |
| |
| qcom,fg-batt-soc@4000 { |
| status = "okay"; |
| reg = <0x4000 0x100>; |
| interrupts = <0x0 0x40 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x40 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x40 0x2 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 0x3 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x40 0x5 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x0 0x40 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x40 0x7 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "soc-update", |
| "soc-ready", |
| "bsoc-delta", |
| "msoc-delta", |
| "msoc-low", |
| "msoc-empty", |
| "msoc-high", |
| "msoc-full"; |
| }; |
| |
| qcom,fg-batt-info@4100 { |
| status = "okay"; |
| reg = <0x4100 0x100>; |
| interrupts = <0x0 0x41 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x41 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x41 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x41 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x41 0x6 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "vbatt-pred-delta", |
| "vbatt-low", |
| "esr-delta", |
| "batt-missing", |
| "batt-temp-delta"; |
| }; |
| |
| qcom,fg-memif@4400 { |
| status = "okay"; |
| reg = <0x4400 0x100>; |
| interrupts = <0x0 0x44 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x44 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x0 0x44 0x2 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "ima-rdy", |
| "mem-xcp", |
| "dma-grant"; |
| }; |
| }; |
| |
| bcl@4200 { |
| compatible = "qcom,msm-bcl-lmh"; |
| reg = <0x4200 0xff>, |
| <0x4300 0xff>; |
| reg-names = "fg_user_adc", |
| "fg_lmh"; |
| interrupts = <0x0 0x42 0x0 IRQ_TYPE_NONE>, |
| <0x0 0x42 0x2 IRQ_TYPE_NONE>; |
| interrupt-names = "bcl-high-ibat-int", |
| "bcl-low-vbat-int"; |
| qcom,vbat-polling-delay-ms = <100>; |
| qcom,ibat-polling-delay-ms = <100>; |
| }; |
| }; |
| |
| qcom,pm660@1 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm660_haptics: qcom,haptics@c000 { |
| compatible = "qcom,qpnp-haptics"; |
| reg = <0xc000 0x100>; |
| interrupts = <0x1 0xc0 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x1 0xc0 0x1 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "hap-sc-irq", "hap-play-irq"; |
| qcom,pmic-revid = <&pm660_revid>; |
| qcom,pmic-misc = <&pm660_misc>; |
| qcom,misc-clk-trim-error-reg = <0xf3>; |
| qcom,actuator-type = <0>; |
| qcom,play-mode = "direct"; |
| qcom,vmax-mv = <3200>; |
| qcom,ilim-ma = <800>; |
| qcom,sc-dbc-cycles = <8>; |
| qcom,wave-play-rate-us = <6667>; |
| qcom,en-brake; |
| qcom,lra-high-z = "opt0"; |
| qcom,lra-auto-res-mode = "qwd"; |
| qcom,lra-res-cal-period = <4>; |
| }; |
| }; |
| }; |
| |
| &thermal_zones { |
| xo-therm-adc { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm660_adc_tm 0x4c>; |
| thermal-governor = "user_space"; |
| |
| trips { |
| active-config0 { |
| temperature = <65000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| msm-therm-adc { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm660_adc_tm 0x4d>; |
| thermal-governor = "user_space"; |
| |
| trips { |
| active-config0 { |
| temperature = <65000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| emmc-therm-adc { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm660_adc_tm 0x4e>; |
| thermal-governor = "user_space"; |
| |
| trips { |
| active-config0 { |
| temperature = <65000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pa-therm0-adc { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm660_adc_tm 0x4f>; |
| thermal-governor = "user_space"; |
| |
| trips { |
| active-config0 { |
| temperature = <65000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| quiet-therm-adc { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&pm660_adc_tm 0x51>; |
| thermal-governor = "user_space"; |
| |
| trips { |
| active-config0 { |
| temperature = <65000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |