| /* |
| * File: drivers/input/keyboard/adp5588_keys.c |
| * Description: keypad driver for ADP5588 and ADP5587 |
| * I2C QWERTY Keypad and IO Expander |
| * Bugs: Enter bugs at http://blackfin.uclinux.org/ |
| * |
| * Copyright (C) 2008-2010 Analog Devices Inc. |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/workqueue.h> |
| #include <linux/errno.h> |
| #include <linux/pm.h> |
| #include <linux/platform_device.h> |
| #include <linux/input.h> |
| #include <linux/i2c.h> |
| #include <linux/gpio.h> |
| #include <linux/slab.h> |
| |
| #include <linux/i2c/adp5588.h> |
| |
| /* Key Event Register xy */ |
| #define KEY_EV_PRESSED (1 << 7) |
| #define KEY_EV_MASK (0x7F) |
| |
| #define KP_SEL(x) (0xFFFF >> (16 - x)) /* 2^x-1 */ |
| |
| #define KEYP_MAX_EVENT 10 |
| |
| /* |
| * Early pre 4.0 Silicon required to delay readout by at least 25ms, |
| * since the Event Counter Register updated 25ms after the interrupt |
| * asserted. |
| */ |
| #define WA_DELAYED_READOUT_REVID(rev) ((rev) < 4) |
| |
| struct adp5588_kpad { |
| struct i2c_client *client; |
| struct input_dev *input; |
| struct delayed_work work; |
| unsigned long delay; |
| unsigned short keycode[ADP5588_KEYMAPSIZE]; |
| const struct adp5588_gpi_map *gpimap; |
| unsigned short gpimapsize; |
| #ifdef CONFIG_GPIOLIB |
| unsigned char gpiomap[ADP5588_MAXGPIO]; |
| bool export_gpio; |
| struct gpio_chip gc; |
| struct mutex gpio_lock; /* Protect cached dir, dat_out */ |
| u8 dat_out[3]; |
| u8 dir[3]; |
| #endif |
| }; |
| |
| static int adp5588_read(struct i2c_client *client, u8 reg) |
| { |
| int ret = i2c_smbus_read_byte_data(client, reg); |
| |
| if (ret < 0) |
| dev_err(&client->dev, "Read Error\n"); |
| |
| return ret; |
| } |
| |
| static int adp5588_write(struct i2c_client *client, u8 reg, u8 val) |
| { |
| return i2c_smbus_write_byte_data(client, reg, val); |
| } |
| |
| #ifdef CONFIG_GPIOLIB |
| static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off) |
| { |
| struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc); |
| unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]); |
| |
| return !!(adp5588_read(kpad->client, GPIO_DAT_STAT1 + bank) & bit); |
| } |
| |
| static void adp5588_gpio_set_value(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc); |
| unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]); |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| if (val) |
| kpad->dat_out[bank] |= bit; |
| else |
| kpad->dat_out[bank] &= ~bit; |
| |
| adp5588_write(kpad->client, GPIO_DAT_OUT1 + bank, |
| kpad->dat_out[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| } |
| |
| static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off) |
| { |
| struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc); |
| unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]); |
| int ret; |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| kpad->dir[bank] &= ~bit; |
| ret = adp5588_write(kpad->client, GPIO_DIR1 + bank, kpad->dir[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| |
| return ret; |
| } |
| |
| static int adp5588_gpio_direction_output(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| struct adp5588_kpad *kpad = container_of(chip, struct adp5588_kpad, gc); |
| unsigned int bank = ADP5588_BANK(kpad->gpiomap[off]); |
| unsigned int bit = ADP5588_BIT(kpad->gpiomap[off]); |
| int ret; |
| |
| mutex_lock(&kpad->gpio_lock); |
| |
| kpad->dir[bank] |= bit; |
| |
| if (val) |
| kpad->dat_out[bank] |= bit; |
| else |
| kpad->dat_out[bank] &= ~bit; |
| |
| ret = adp5588_write(kpad->client, GPIO_DAT_OUT1 + bank, |
| kpad->dat_out[bank]); |
| ret |= adp5588_write(kpad->client, GPIO_DIR1 + bank, |
| kpad->dir[bank]); |
| |
| mutex_unlock(&kpad->gpio_lock); |
| |
| return ret; |
| } |
| |
| static int adp5588_build_gpiomap(struct adp5588_kpad *kpad, |
| const struct adp5588_kpad_platform_data *pdata) |
| { |
| bool pin_used[ADP5588_MAXGPIO]; |
| int n_unused = 0; |
| int i; |
| |
| memset(pin_used, 0, sizeof(pin_used)); |
| |
| for (i = 0; i < pdata->rows; i++) |
| pin_used[i] = true; |
| |
| for (i = 0; i < pdata->cols; i++) |
| pin_used[i + GPI_PIN_COL_BASE - GPI_PIN_BASE] = true; |
| |
| for (i = 0; i < kpad->gpimapsize; i++) |
| pin_used[kpad->gpimap[i].pin - GPI_PIN_BASE] = true; |
| |
| for (i = 0; i < ADP5588_MAXGPIO; i++) |
| if (!pin_used[i]) |
| kpad->gpiomap[n_unused++] = i; |
| |
| return n_unused; |
| } |
| |
| static int adp5588_gpio_add(struct adp5588_kpad *kpad) |
| { |
| struct device *dev = &kpad->client->dev; |
| const struct adp5588_kpad_platform_data *pdata = dev->platform_data; |
| const struct adp5588_gpio_platform_data *gpio_data = pdata->gpio_data; |
| int i, error; |
| |
| if (!gpio_data) |
| return 0; |
| |
| kpad->gc.ngpio = adp5588_build_gpiomap(kpad, pdata); |
| if (kpad->gc.ngpio == 0) { |
| dev_info(dev, "No unused gpios left to export\n"); |
| return 0; |
| } |
| |
| kpad->export_gpio = true; |
| |
| kpad->gc.direction_input = adp5588_gpio_direction_input; |
| kpad->gc.direction_output = adp5588_gpio_direction_output; |
| kpad->gc.get = adp5588_gpio_get_value; |
| kpad->gc.set = adp5588_gpio_set_value; |
| kpad->gc.can_sleep = 1; |
| |
| kpad->gc.base = gpio_data->gpio_start; |
| kpad->gc.label = kpad->client->name; |
| kpad->gc.owner = THIS_MODULE; |
| kpad->gc.names = gpio_data->names; |
| |
| mutex_init(&kpad->gpio_lock); |
| |
| error = gpiochip_add(&kpad->gc); |
| if (error) { |
| dev_err(dev, "gpiochip_add failed, err: %d\n", error); |
| return error; |
| } |
| |
| for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { |
| kpad->dat_out[i] = adp5588_read(kpad->client, |
| GPIO_DAT_OUT1 + i); |
| kpad->dir[i] = adp5588_read(kpad->client, GPIO_DIR1 + i); |
| } |
| |
| if (gpio_data->setup) { |
| error = gpio_data->setup(kpad->client, |
| kpad->gc.base, kpad->gc.ngpio, |
| gpio_data->context); |
| if (error) |
| dev_warn(dev, "setup failed, %d\n", error); |
| } |
| |
| return 0; |
| } |
| |
| static void adp5588_gpio_remove(struct adp5588_kpad *kpad) |
| { |
| struct device *dev = &kpad->client->dev; |
| const struct adp5588_kpad_platform_data *pdata = dev->platform_data; |
| const struct adp5588_gpio_platform_data *gpio_data = pdata->gpio_data; |
| int error; |
| |
| if (!kpad->export_gpio) |
| return; |
| |
| if (gpio_data->teardown) { |
| error = gpio_data->teardown(kpad->client, |
| kpad->gc.base, kpad->gc.ngpio, |
| gpio_data->context); |
| if (error) |
| dev_warn(dev, "teardown failed %d\n", error); |
| } |
| |
| error = gpiochip_remove(&kpad->gc); |
| if (error) |
| dev_warn(dev, "gpiochip_remove failed %d\n", error); |
| } |
| #else |
| static inline int adp5588_gpio_add(struct adp5588_kpad *kpad) |
| { |
| return 0; |
| } |
| |
| static inline void adp5588_gpio_remove(struct adp5588_kpad *kpad) |
| { |
| } |
| #endif |
| |
| static void adp5588_report_events(struct adp5588_kpad *kpad, int ev_cnt) |
| { |
| int i, j; |
| |
| for (i = 0; i < ev_cnt; i++) { |
| int key = adp5588_read(kpad->client, Key_EVENTA + i); |
| int key_val = key & KEY_EV_MASK; |
| |
| if (key_val >= GPI_PIN_BASE && key_val <= GPI_PIN_END) { |
| for (j = 0; j < kpad->gpimapsize; j++) { |
| if (key_val == kpad->gpimap[j].pin) { |
| input_report_switch(kpad->input, |
| kpad->gpimap[j].sw_evt, |
| key & KEY_EV_PRESSED); |
| break; |
| } |
| } |
| } else { |
| input_report_key(kpad->input, |
| kpad->keycode[key_val - 1], |
| key & KEY_EV_PRESSED); |
| } |
| } |
| } |
| |
| static void adp5588_work(struct work_struct *work) |
| { |
| struct adp5588_kpad *kpad = container_of(work, |
| struct adp5588_kpad, work.work); |
| struct i2c_client *client = kpad->client; |
| int status, ev_cnt; |
| |
| status = adp5588_read(client, INT_STAT); |
| |
| if (status & ADP5588_OVR_FLOW_INT) /* Unlikely and should never happen */ |
| dev_err(&client->dev, "Event Overflow Error\n"); |
| |
| if (status & ADP5588_KE_INT) { |
| ev_cnt = adp5588_read(client, KEY_LCK_EC_STAT) & ADP5588_KEC; |
| if (ev_cnt) { |
| adp5588_report_events(kpad, ev_cnt); |
| input_sync(kpad->input); |
| } |
| } |
| adp5588_write(client, INT_STAT, status); /* Status is W1C */ |
| } |
| |
| static irqreturn_t adp5588_irq(int irq, void *handle) |
| { |
| struct adp5588_kpad *kpad = handle; |
| |
| /* |
| * use keventd context to read the event fifo registers |
| * Schedule readout at least 25ms after notification for |
| * REVID < 4 |
| */ |
| |
| schedule_delayed_work(&kpad->work, kpad->delay); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int adp5588_setup(struct i2c_client *client) |
| { |
| const struct adp5588_kpad_platform_data *pdata = client->dev.platform_data; |
| const struct adp5588_gpio_platform_data *gpio_data = pdata->gpio_data; |
| int i, ret; |
| unsigned char evt_mode1 = 0, evt_mode2 = 0, evt_mode3 = 0; |
| |
| ret = adp5588_write(client, KP_GPIO1, KP_SEL(pdata->rows)); |
| ret |= adp5588_write(client, KP_GPIO2, KP_SEL(pdata->cols) & 0xFF); |
| ret |= adp5588_write(client, KP_GPIO3, KP_SEL(pdata->cols) >> 8); |
| |
| if (pdata->en_keylock) { |
| ret |= adp5588_write(client, UNLOCK1, pdata->unlock_key1); |
| ret |= adp5588_write(client, UNLOCK2, pdata->unlock_key2); |
| ret |= adp5588_write(client, KEY_LCK_EC_STAT, ADP5588_K_LCK_EN); |
| } |
| |
| for (i = 0; i < KEYP_MAX_EVENT; i++) |
| ret |= adp5588_read(client, Key_EVENTA); |
| |
| for (i = 0; i < pdata->gpimapsize; i++) { |
| unsigned short pin = pdata->gpimap[i].pin; |
| |
| if (pin <= GPI_PIN_ROW_END) { |
| evt_mode1 |= (1 << (pin - GPI_PIN_ROW_BASE)); |
| } else { |
| evt_mode2 |= ((1 << (pin - GPI_PIN_COL_BASE)) & 0xFF); |
| evt_mode3 |= ((1 << (pin - GPI_PIN_COL_BASE)) >> 8); |
| } |
| } |
| |
| if (pdata->gpimapsize) { |
| ret |= adp5588_write(client, GPI_EM1, evt_mode1); |
| ret |= adp5588_write(client, GPI_EM2, evt_mode2); |
| ret |= adp5588_write(client, GPI_EM3, evt_mode3); |
| } |
| |
| if (gpio_data) { |
| for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { |
| int pull_mask = gpio_data->pullup_dis_mask; |
| |
| ret |= adp5588_write(client, GPIO_PULL1 + i, |
| (pull_mask >> (8 * i)) & 0xFF); |
| } |
| } |
| |
| ret |= adp5588_write(client, INT_STAT, |
| ADP5588_CMP2_INT | ADP5588_CMP1_INT | |
| ADP5588_OVR_FLOW_INT | ADP5588_K_LCK_INT | |
| ADP5588_GPI_INT | ADP5588_KE_INT); /* Status is W1C */ |
| |
| ret |= adp5588_write(client, CFG, ADP5588_INT_CFG | |
| ADP5588_OVR_FLOW_IEN | |
| ADP5588_KE_IEN); |
| |
| if (ret < 0) { |
| dev_err(&client->dev, "Write Error\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void adp5588_report_switch_state(struct adp5588_kpad *kpad) |
| { |
| int gpi_stat1 = adp5588_read(kpad->client, GPIO_DAT_STAT1); |
| int gpi_stat2 = adp5588_read(kpad->client, GPIO_DAT_STAT2); |
| int gpi_stat3 = adp5588_read(kpad->client, GPIO_DAT_STAT3); |
| int gpi_stat_tmp, pin_loc; |
| int i; |
| |
| for (i = 0; i < kpad->gpimapsize; i++) { |
| unsigned short pin = kpad->gpimap[i].pin; |
| |
| if (pin <= GPI_PIN_ROW_END) { |
| gpi_stat_tmp = gpi_stat1; |
| pin_loc = pin - GPI_PIN_ROW_BASE; |
| } else if ((pin - GPI_PIN_COL_BASE) < 8) { |
| gpi_stat_tmp = gpi_stat2; |
| pin_loc = pin - GPI_PIN_COL_BASE; |
| } else { |
| gpi_stat_tmp = gpi_stat3; |
| pin_loc = pin - GPI_PIN_COL_BASE - 8; |
| } |
| |
| if (gpi_stat_tmp < 0) { |
| dev_err(&kpad->client->dev, |
| "Can't read GPIO_DAT_STAT switch %d default to OFF\n", |
| pin); |
| gpi_stat_tmp = 0; |
| } |
| |
| input_report_switch(kpad->input, |
| kpad->gpimap[i].sw_evt, |
| !(gpi_stat_tmp & (1 << pin_loc))); |
| } |
| |
| input_sync(kpad->input); |
| } |
| |
| |
| static int adp5588_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct adp5588_kpad *kpad; |
| const struct adp5588_kpad_platform_data *pdata = client->dev.platform_data; |
| struct input_dev *input; |
| unsigned int revid; |
| int ret, i; |
| int error; |
| |
| if (!i2c_check_functionality(client->adapter, |
| I2C_FUNC_SMBUS_BYTE_DATA)) { |
| dev_err(&client->dev, "SMBUS Byte Data not Supported\n"); |
| return -EIO; |
| } |
| |
| if (!pdata) { |
| dev_err(&client->dev, "no platform data?\n"); |
| return -EINVAL; |
| } |
| |
| if (!pdata->rows || !pdata->cols || !pdata->keymap) { |
| dev_err(&client->dev, "no rows, cols or keymap from pdata\n"); |
| return -EINVAL; |
| } |
| |
| if (pdata->keymapsize != ADP5588_KEYMAPSIZE) { |
| dev_err(&client->dev, "invalid keymapsize\n"); |
| return -EINVAL; |
| } |
| |
| if (!pdata->gpimap && pdata->gpimapsize) { |
| dev_err(&client->dev, "invalid gpimap from pdata\n"); |
| return -EINVAL; |
| } |
| |
| if (pdata->gpimapsize > ADP5588_GPIMAPSIZE_MAX) { |
| dev_err(&client->dev, "invalid gpimapsize\n"); |
| return -EINVAL; |
| } |
| |
| for (i = 0; i < pdata->gpimapsize; i++) { |
| unsigned short pin = pdata->gpimap[i].pin; |
| |
| if (pin < GPI_PIN_BASE || pin > GPI_PIN_END) { |
| dev_err(&client->dev, "invalid gpi pin data\n"); |
| return -EINVAL; |
| } |
| |
| if (pin <= GPI_PIN_ROW_END) { |
| if (pin - GPI_PIN_ROW_BASE + 1 <= pdata->rows) { |
| dev_err(&client->dev, "invalid gpi row data\n"); |
| return -EINVAL; |
| } |
| } else { |
| if (pin - GPI_PIN_COL_BASE + 1 <= pdata->cols) { |
| dev_err(&client->dev, "invalid gpi col data\n"); |
| return -EINVAL; |
| } |
| } |
| } |
| |
| if (!client->irq) { |
| dev_err(&client->dev, "no IRQ?\n"); |
| return -EINVAL; |
| } |
| |
| kpad = kzalloc(sizeof(*kpad), GFP_KERNEL); |
| input = input_allocate_device(); |
| if (!kpad || !input) { |
| error = -ENOMEM; |
| goto err_free_mem; |
| } |
| |
| kpad->client = client; |
| kpad->input = input; |
| INIT_DELAYED_WORK(&kpad->work, adp5588_work); |
| |
| ret = adp5588_read(client, DEV_ID); |
| if (ret < 0) { |
| error = ret; |
| goto err_free_mem; |
| } |
| |
| revid = (u8) ret & ADP5588_DEVICE_ID_MASK; |
| if (WA_DELAYED_READOUT_REVID(revid)) |
| kpad->delay = msecs_to_jiffies(30); |
| |
| input->name = client->name; |
| input->phys = "adp5588-keys/input0"; |
| input->dev.parent = &client->dev; |
| |
| input_set_drvdata(input, kpad); |
| |
| input->id.bustype = BUS_I2C; |
| input->id.vendor = 0x0001; |
| input->id.product = 0x0001; |
| input->id.version = revid; |
| |
| input->keycodesize = sizeof(kpad->keycode[0]); |
| input->keycodemax = pdata->keymapsize; |
| input->keycode = kpad->keycode; |
| |
| memcpy(kpad->keycode, pdata->keymap, |
| pdata->keymapsize * input->keycodesize); |
| |
| kpad->gpimap = pdata->gpimap; |
| kpad->gpimapsize = pdata->gpimapsize; |
| |
| /* setup input device */ |
| __set_bit(EV_KEY, input->evbit); |
| |
| if (pdata->repeat) |
| __set_bit(EV_REP, input->evbit); |
| |
| for (i = 0; i < input->keycodemax; i++) |
| if (kpad->keycode[i] <= KEY_MAX) |
| __set_bit(kpad->keycode[i], input->keybit); |
| __clear_bit(KEY_RESERVED, input->keybit); |
| |
| if (kpad->gpimapsize) |
| __set_bit(EV_SW, input->evbit); |
| for (i = 0; i < kpad->gpimapsize; i++) |
| __set_bit(kpad->gpimap[i].sw_evt, input->swbit); |
| |
| error = input_register_device(input); |
| if (error) { |
| dev_err(&client->dev, "unable to register input device\n"); |
| goto err_free_mem; |
| } |
| |
| error = request_irq(client->irq, adp5588_irq, |
| IRQF_TRIGGER_FALLING, |
| client->dev.driver->name, kpad); |
| if (error) { |
| dev_err(&client->dev, "irq %d busy?\n", client->irq); |
| goto err_unreg_dev; |
| } |
| |
| error = adp5588_setup(client); |
| if (error) |
| goto err_free_irq; |
| |
| if (kpad->gpimapsize) |
| adp5588_report_switch_state(kpad); |
| |
| error = adp5588_gpio_add(kpad); |
| if (error) |
| goto err_free_irq; |
| |
| device_init_wakeup(&client->dev, 1); |
| i2c_set_clientdata(client, kpad); |
| |
| dev_info(&client->dev, "Rev.%d keypad, irq %d\n", revid, client->irq); |
| return 0; |
| |
| err_free_irq: |
| free_irq(client->irq, kpad); |
| err_unreg_dev: |
| input_unregister_device(input); |
| input = NULL; |
| err_free_mem: |
| input_free_device(input); |
| kfree(kpad); |
| |
| return error; |
| } |
| |
| static int adp5588_remove(struct i2c_client *client) |
| { |
| struct adp5588_kpad *kpad = i2c_get_clientdata(client); |
| |
| adp5588_write(client, CFG, 0); |
| free_irq(client->irq, kpad); |
| cancel_delayed_work_sync(&kpad->work); |
| input_unregister_device(kpad->input); |
| adp5588_gpio_remove(kpad); |
| kfree(kpad); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int adp5588_suspend(struct device *dev) |
| { |
| struct adp5588_kpad *kpad = dev_get_drvdata(dev); |
| struct i2c_client *client = kpad->client; |
| |
| disable_irq(client->irq); |
| cancel_delayed_work_sync(&kpad->work); |
| |
| if (device_may_wakeup(&client->dev)) |
| enable_irq_wake(client->irq); |
| |
| return 0; |
| } |
| |
| static int adp5588_resume(struct device *dev) |
| { |
| struct adp5588_kpad *kpad = dev_get_drvdata(dev); |
| struct i2c_client *client = kpad->client; |
| |
| if (device_may_wakeup(&client->dev)) |
| disable_irq_wake(client->irq); |
| |
| enable_irq(client->irq); |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops adp5588_dev_pm_ops = { |
| .suspend = adp5588_suspend, |
| .resume = adp5588_resume, |
| }; |
| #endif |
| |
| static const struct i2c_device_id adp5588_id[] = { |
| { "adp5588-keys", 0 }, |
| { "adp5587-keys", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, adp5588_id); |
| |
| static struct i2c_driver adp5588_driver = { |
| .driver = { |
| .name = KBUILD_MODNAME, |
| #ifdef CONFIG_PM |
| .pm = &adp5588_dev_pm_ops, |
| #endif |
| }, |
| .probe = adp5588_probe, |
| .remove = adp5588_remove, |
| .id_table = adp5588_id, |
| }; |
| |
| module_i2c_driver(adp5588_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>"); |
| MODULE_DESCRIPTION("ADP5588/87 Keypad driver"); |